Philips E3 User Manual

E3 Series

GENERAL DUTY THERMOPLASTIC EMERGENCY LIGHTING

Page 1 of 2

E3112WS92SD2

E3112WPT86W2

11.87 "

(30.15 cm)

13.01"

(33.05 cm)

14.53"

(36.91 cm)

5.0"

(12.7 cm)

6.84"

(17.37 cm)

Features

Illumination: Illumination

is accomplished with up to

three lamp heads mounted

on the top of the unit. Most

often specified is Lightolier’s

“S” series rectangular lamp

heads. The “S” series lamp

heads incorporate a high

performance parabolic

reflector with a wedge base

tungsten lamp allowing

maximum spacing between

units along a path of egress.

A complete offering of Par 36

sealed beam tungsten, halogen

or MR16 LED lamp heads are

also available.

Housing: Constructed of

impact-resistant, UL 94 V-0,

5 VA thermoplastic. Mounting

is accomplished by means of

the universal j-box mounting

pattern or the keyhole

knockouts provided on the

rear of the housing. The cover

assembly closes and remains

secure via a snap-fit design

and offers tool-free access to

the housing interior. White or

black housing and lamp head

colors are available.

Operating Temperature

Range: Standard Location:

65°F (19°C) to 85°F (30°C)

Damp Location: 32°F (0°C) to

104°F (40°C)

Non-Diagnostic

Electronics: Standard

electronics systems include

a 120/277 VAC dual tap

input transformer. Standard

electronic performance

features include AC line latch,

brownout detection, and

low-voltage battery disconnect

circuitry to maximize battery

service life.

Self-Diagnostics

Electronics: Charging system

is microprocessor driven with

software embedded diagnostic

routine and temperature

compensation. 120/277 VAC

input, surge protection,

brownout , AC lockout, and

low voltage disconnect features

are standard.

Job Information Type:

Job Name:

Cat. No.:

Self-Testing Diagnostics

(optional): The diagnostic/

charging platform with self-

testing mode automatically

runs a one-minute self-test

every 30 days and a 30-minute

test on the sixth and twelfth

month. A one-minute or

90-minute test may be initiated

via the push to test switch on

the unit or by activating the

appropriate test command on

the optional IR test device.

Code Compliance

UL 924 listed. NFPA 101,

NEC, BOCA, OSHA and

IBC illumination standards.

Optional UL damp location

listing available (SD2 models

only) 0°C to 40°C.

Warranty

Three year full electronics

warranty. One year full plus

four year prorated lead calcium

battery warranty. Five year full

plus five year prorated nickel

cadmium battery warranty.

Notes:

E3 Series

GENERAL DUTY THERMOPLASTIC EMERGENCY LIGHTING

Ordering Information

Page 2 of 2

Lamp Heads

6 V Tungsten

S6 = 5.4 W S7 = 7.2 W S9 = 9 W

12 V Tungsten

S9 = 9 W S12 = 12.5 W S18 = 18 W

MR16 LED Lamp Heads* 12 V LED M7F** = 7 Watt , 35°

# of Heads

Blank = No Lamp Heads

1 = One Lamp Head 2 = Two Lamp Heads 3 = Three Lamp Heads

Model Designator

Blank = Standard, Non-Diagnostic Unit SD2 = Diagnostic Electronics

Factory Installed Options

A = Ammeter BD = Battery Disconnect Switch DL = Damp Location Listed EX = Special Input Transformer (specify voltage &

frequency)

F1 = 120 VAC Input Fuse F2 = 277 VAC Input Fuse P1 = 120 VAC Power Switch P2 = 277 VAC Power Switch T = Self-Testing Diagnostics TA = Audible Self-Testing Diagnostics TD = Time Delay, 15 Minutes V = Voltmeter

Housing Color

W = White B = Black

Series

6 V Lead Calcium

E3112 = 12 W E3125 = 25 W E3136 = 36 W E3150 = 50 W

6 V Nickel Calcium

E31N25 = 25 W E31N50 = 50 W

Accessories (order as a separate item) SDREMOTE = Infrared Remote Test Device PCS1 = Polycarbonate Vandal Shield WG5 = Wire Guard

Note 1) Not available with DL option. 2) Only available with non-diagnostic models. 3) Only available with diagnostic electronic models. 4) Some option combinations

may impact UL listing, consult factor y for specifics.

* Lamp included per UL acceptance. ** UL testing restricts using any substitutes for this lamp option.

12 V Lead Calcium

E3225 = 25 W E3236 = 36 W

E3250 = 50 W

12 V Nickel Calcium

E32N25 = 25 W E32N50 = 50 W

Electrical Specifications

Non-Diagnostic Models (60 Hz)

6 V Lead Calcium: 0.115 A (120 VAC), 0.050 A (277 VAC)

6 V NiCad: 0.160 A (120 VAC), 0.071 A (277 VAC)

12 V Lead Calcium: 0.126 A (120 VAC), 0.055 A (277 VAC)

12 V NiCad: 0.116 A (120 VAC), 0.051 A (277 VAC)

Self-Diagnostics Models (60 Hz)

6 V Lead Calcium: 0.113 A (120 VAC), 0.055 A (277 VAC)

6 V NiCad: 0.157 A (120 VAC), 0.065 A (277 VAC)

12 V Lead Calcium: 0.331 A (120 VAC), 0.146 A (277 VAC)

12 V NiCad: 0.200 A (120 VAC), 0.094 A (277 VAC)

Optics Wall mounted 7.5' AFF, ‘S9’ 6 V 9 W Tungsten Lamps Represented

7.5 ft.

0.3

0.4

1.1

0.7

1.2

2.3

0.6

2.4

1.8

0.4

2.3

1.0

0.4

1.6

0.6

0.5

0.9

0.6

0.4

0.7

0.6

0.4

0.9

0.8

0.5

1.4

1.5

0.8

2.3

2.4

2.6

1.7

0.9

25 ft.

0.3

0.2

Average initial footcandles at floor = 1.08

Maximum initial footcandles at floor = 3.0

Minimum initial footcandles at floor = 0.3

Maximum to minimum ratio = 10.00

* The optics layout shown is intended to be used as reference only. Standard reflectances used were 8 0/50/20. Lightolier is not responsible for site specific conditions that may alter the results.

Philips Lightolier e: lol.webmaster@philips.com t: (508) 679-8131 w: www.lightolier.com

E3 Series August 9, 2012

1.6

0.5

0.3

1 FC Average

0.7

2.0

0.4

0.7

0.6

1.9

0.7

2.2

0.4

2.6

2.0

1.3

0.4

Job Information Type:

0.7

0.4

1.2

0.6

0.4

0.8

0.6

0.4

0.7

0.6

0.4

1.1

0.6

1.8

2.0

0.7

2.5

2.2

0.4

2.2

0.9

0.2

0.8

0.2

0.3

6 ft.