Philips DVP-3300 Service Manual
DVP3111 DVP3300(X)
DVP3111/55
DVP3300/93
DVP3300/96
Service Manual
ABLE OF CONTENTS
T
echnical Specifications…………....………………………..............1-2
. T
. Safety Instruction, Warning & Notes….……………………....….....1-3
. DFU Instruction..............................................................................2-1
. Mechanical and Dismantling Instructions…………........................3-1
. Software Version & Upgrades, Region Code Change..…….........
Trouble Shooting Chart…………………..……………………………
.
. Wiring Diagram………………………………………..……
. Electrical Diagrams and Print-layouts..….…………………....….…7-1
. Packing, Set Mechanical Exploded view & Part list.………..….….8-1
. Revision List..................................................................................9-1
©Copy
right 2009 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
Page
.
4-1
.
5-1
…..….….6-1
CLASS 1
LASER PRODUCT
Published by FK-0940 BU AVM Printed in The Netherlands Subject to modification
ersion 1.1
V
GB
3141 785 34461
PHILIPS
1-2
Specifi cations
Note
•
Specifi cation and design are subjec t to change
without notice
Accessories supplied
Remote control and batteries•
Audio/Video cables•
Power plug adaptor•
User Manual•
Play media
DVD-Video, Video CD/SVCD, Audio CD, •
CD-R /CD-RW, DVD+R /+RW, DVD-R /RW, DivX-CD, Picture CD, MP3-CD
TV standard
Number of lines:•
625 (PAL/50Hz); 525 (NTSC/60Hz)•
Play: Multi-standard (PAL/NTSC)•
Video performance
Video DAC: 12 bits, 108 MHz•
Video output: 1 Vpp ~ 75 ohm•
Video format
Digital compression:•
DVD/SVCD/VCD/DivX•
Horizontal resolution:•
DVD: 720 pixels (50 Hz); 720 pixels •
(60 Hz)
VCD: 352 pixels (50 Hz); 352 pixels •
(60 Hz)
Vertical resolution:•
DVD: 576 pixels (50 Hz); 480 pixels •
(60 Hz)
VCD: 288 lines (50 Hz); 240 lines •
(60 Hz)
for DVP3111/55
Audio format
Digital: •
MPEG/AC-3: Compressed digital (16, •
20, 24 bits, fs 44.1, 48, 96 kHz)
MP3: 96, 112, 128, 256 kbps & •
variable bit rate, fs 32, 44.1, 48 kHz
Analog sound stereo•
Dolby surround compatible downmix •
from Dolby Digital multi-channel sound
Connections
Video output: Cinch (yellow)•
Audio output (L+R): Cinch (white/red)•
Digital output: •
1 coaxial: IEC60958 for CDDA/•
LPCM; IEC61937 for MPEG 1/2,
Dolby Digital
Main unit
Dimensions (w x h x d): 360 x 37 x 209 •
(mm)
Net Weight: approximately 1.3 kg•
Power
Power supply rating: 110 - 240V, 50/60HZ•
Power consumption: <10 W•
Power consumption in standby mode: •
<1 W
Laser specifi cation
Type: Semiconductor laser InGaAIP •
(DVD), AIGaAs (CD)
Wave length: 658 nm (DVD), 790 nm •
(CD)
Output Power: 7.0 mW (DVD), 10.0 mW •
(VCD/CD)
Beam divergence: 60 degrees•
Audio performance
DA converter: 24 bits, 192 kHz•
Frequency response: •
DVD: 4 Hz - 22 kHz (48 kHz); 4 Hz - •
44 kHz (96 kHz)
SVCD: 4 Hz - 20 kHz (44.1 kHz); 4 •
Hz - 22 kHz (48 kHz)
CD/VCD: 4 Hz - 20 kHz (44.1 kHz) •
Signal-Noise (1 kHz): > 90 dB •
(A-weighted)
Dynamic range (1 kHz): > 80 dB •
(A-weighted)
Crosstalk (1 kHz): > 90 dB•
Distortion/noise (1 kHz): > 65 dB•
MP3: MPEG L3•
1-2
Specifications
Note
Specification and design are subject to change
•
without notice
Accessories supplied
Remote control and batteries•
Audio/Video cables•
User Manual•
Play media
DVD-Video, Video CD/SVCD, Audio CD, •
CD-R/CD-RW, DVD+R/+RW, DVDR/-RW, DivX-CD, Picture CD, MP3-CD,
USB flash drive
TV standard
Number of lines:•
625 (PAL/50Hz); 525 (NTSC/60Hz)•
Play: Multi-standard (PAL/NTSC)•
Video performance
Video DAC: 12 bits, 108 MHz•
Video output: 1 Vpp ~ 75 ohm•
Video format
Digital compression:•
DVD/SVCD/VCD/DivX•
Horizontal resolution:•
DVD: 720 pixels (50 Hz); 720 pixels •
(60 Hz)
VCD: 352 pixels (50 Hz); 352 pixels •
(60 Hz)
Vertical resolution:•
DVD: 576 pixels (50 Hz); 480 pixels •
(60 Hz)
VCD: 288 lines (50 Hz); 240 lines •
(60 Hz)
Audio performance
DA converter: 24 bits, 192 kHz•
Frequency response: •
DVD: 4 Hz - 22 kHz (48 kHz); 4 Hz - •
44 kHz (96 kHz)
SVCD: 4 Hz - 20 kHz (44.1 kHz); 4 •
Hz - 22 kHz (48 kHz)
CD/VCD: 4 Hz - 20 kHz (44.1 kHz) •
Signal-Noise (1 kHz): > 90 dB •
(A-weighted)
Dynamic range (1 kHz): > 80 dB •
(A-weighted)
Crosstalk (1 kHz): > 90 dB•
Distortion/noise (1 kHz): > 65 dB•
MP3: MPEG L3•
for DVP3300(X)/93/96
Audio format
Digital: •
MPEG/AC-3: Compressed digital (16, •
20, 24 bits, fs 44.1, 48, 96 kHz)
MP3: 96, 112, 128, 256 kbps & •
variable bit rate, fs 32, 44.1, 48 kHz
Analog sound stereo•
Dolby surround compatible downmix •
from Dolby Digital multi-channel sound
Connections
Video output: Cinch (yellow)•
Audio output (L+R): Cinch (white/red)•
Digital output: •
1 coaxial: IEC60958 for CDDA/•
LPCM; IEC61937 for MPEG 1/2,
Dolby Digital
Main unit
Dimensions (w x h x d): 360 x 37 x 209 •
(mm)
Net Weight: approximately 1.3 kg•
Power
Power supply rating: 110 - 240V, 50/60HZ•
Power consumption: <10 W•
Power consumption in standby mode: •
<1 W
Laser specification
Type: Semiconductor laser InGaAIP •
(DVD), AIGaAs (CD)
Wave length: 658 nm (DVD), 790 nm •
(CD)
Output Power: 7.0 mW (DVD), 10.0 mW •
(VCD/CD)
Beam divergence: 60 degrees•
1-3
Safety instruction, Warning & Notes
Safety instruction
1. General safety
Safety regulations require that during a repair:
. Connect the unit to the mains via an isolation transformer.
. Replace safety components indicated by the symbol
only by components identical to the original ones. Any
other component substitution (other than original type)
may increase risk of fire or electrical shock hazard.
Safety regulations require that after a repair, you must
return the unit in its original condition. Pay, in particular,
attention to the following points:
. Route the wires/cables correctly, and fix them with the
mounted cable clamps.
. Check the insulation of the mains lead for external
damage.
. Check the electrical DC resistance between the mains
plug and the secondary side:
1) Unplug the mains cord, and connect a wire between
the two pins of the mains plug.
2) Set the mains switch the “on” position (keep the
mains cord unplug).
3) Measure the resistance value between the mains
plug and the front panel, controls, and chassis
bottom.
4) Repair or correct unit when the resistance
measurement is less than 1M
5) Verify this, before you return the unit to the
customer/user (ref. UL-standard no. 1492).
6) Switch the unit “off”, and remove the wire between
the two pins of the mains plug.
¡
.
2.Laser safety
This unit employs a laser. Only qualified service personnel
,
may remove the cover, or attempt to service this device
(due to possible eye injury).
Laser device unit
Type : Semiconductor laser GaAlAs
Wavelength : 650nm (DVD)
: 780nm (VCD/CD)
Output power : 7mW (DVD)
: 10mW (DVD /CD)
Beam divergence: 60 degree
Note: Use of controls or adjustments or performance of
procedure other than those specified herein, may result in
hazardous radiation exposure. Avoid direct exposure to
beam.
Warning
1-4
1.General
. All ICs and many other semiconductors are susceptible to
electrostatic discharges (ESD). Careless handing during
repair can reduce life drastically. Make sure that, during
repair, you are at the same potential as the mass of the
set by a wristband with resistance. Keep components and
tools at this same potential. Available ESD protection
equipment:
1) Complete kit ESD3 (small tablemat, wristband,
connection box, extension cable and earth cable)
4822 310 10671.
2) Wristband tester 4822 344 13999.
. Be careful during measurements in the live voltage
section. The primary side of the power supply , including
the heat sink, carries live mains voltage when you
connect the player to the mains (even when the player is
“off”!). It is possible to touch copper tracks and/or
components in this unshielded primary area, when you
service the player. Service personnel must take
precautions to prevent touching this area or components
in this area. A “lighting stroke” and a stripe-marked
printing on the printed wiring board, indicate the primary
side of the power supply.
. Never replace modules, or components, while the unit is
“on”.
2. Laser
. The use of optical instruments with this product, will
increase eye hazard.
. Only qualified service personnel may remove the cover
or attempt to service this device, due to possible eye
injury.
. Repair handing should take place as much as possible
with a disc loaded inside the player.
. Text below is placed inside the unit, on the laser cover
shield:
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN, AVOID EXPOSURE
TO BEAM.
Notes: Manufactured under licence from Dolby
Laboratories. The double-D symbol is trademarks of Dolby
Laboratories, Inc. All rights reserved.
Notes
Lead-Free requirement for service
1-5
INDENTIFICATION:
Regardless of special logo (not always indicated)
One must treat all sets from 1.1.2005 onwards, according
next rules.
Important note
be treated in this way as long as you avoid mixing
solder-alloys (leaded/ lead-free). So best to always use
SAC305 and the higher temperatures belong to this.
Due to lead-free technology some rules have to be
respected by the workshop during a repair:
x Use only lead-free solder alloy Philips SAC305 with
order code 0622 149 00106. If lead-free solder-paste is
required, please contact the manufacturer of your
solder-equipment. In general use of solder-paste within
workshops should be avoided because paste is not easy
to store and to handle.
x Use only adequate solder tools applicable for lead-free
solder alloy. The solder tool must be able
o To reach at least a solder-temperature of 400°C,
o To stabilize the adjusted temperature at the
o To exchange solder-tips for different applications.
x Adjust your solder tool so that a temperature around
360°C
joint. Heating-time of the solder-joint should not exceed
~ 4 sec. Avoid temperatures above 400°C otherwise
wear-out of tips will rise drastically and flux-fluid will be
destroyed. To avoid wear-out of tips switch off un-used
equipment, or reduce heat.
x Mix of lead-free solder alloy / parts with leaded solder
alloy / parts is possible but PHILIPS recommends
strongly to avoid mixed
solder alloy types (leaded and lead-free). If one cannot
avoid, clean carefully the
solder-joint from old solder alloy and re-solder with new
solder alloy (SAC305).
: In fact also products a little older can also
solder-tip
– 380°C is reached and stabilized at the solder
x Use only original spare-parts listed in the
Service-Manuals. Not listed standard-material
(commodities) has to be purchased at external
companies.
x Special information for BGA-ICs:
- always use the 12nc-recognizable soldering
temperature profile of the specific BGA (for
de-soldering always use highest lead-free
temperature profile, in case of doubt)
- lead free BGA-ICs will be delivered in so-called
‘dry-packaging’ (sealed pack including a silica gel
pack) to protect the IC against moisture. After
opening, dependent of MSL-level seen on
indicator-label in the bag, the BGA-IC possibly
still has to be baked dry. This will be
communicated via AYS-website.
Do not re-use BGAs at all.
x For sets produced before 1.1.2005, containing
leaded soldering-tin and components, all needed
spare-parts will be available till the end of the
service-period. For repair of such sets nothing
changes.
x On our website:
www.atyourservice.ce.Philips.com
You find more information to:
BGA-de-/soldering (+ baking instructions)
Heating-profiles of BGAs and other ICs used in
Philips-sets
You will find this and more technical information
within the “magazine”, chapter “workshop news”.
For additional questions please contact your local
repair-helpdesk.
DVP3300/93 QSG:
2-1
4
The following excerpt of the Quick Start Guide serves as an introduction to the set.
The complete Direction For Use can be download in different languages from
Philips Customer Contact & Support site: www.p4c.philips.com
Register your product and get support at
www.philips.com/welcome
DVP3300
2009 © Koninklijke Philips N.V.
All rights reserved.
Warning
Riskofover heating!NeverinstalltheDVDplayerinaconÀnedspace.Always
leaveaspaceofatleas tfourinchesaroundtheDVDplayerforventilation.Ensure
thecurtainsorotherobjec tsnevercovertheventilationslotsontheDVDplayer.
NeverplacetheDVDplayer,remotecontr olor
otherheatsources,includingdirectsunlight.
OnlyusethisDVDplayerindoors.KeepthisDVDplayerawayfromwater,
moistureandliquid-Àlledobjects.
NeverplacethisDVDplayeronotherelectricalequipment.
KeepawayfromthisDVDplayerduringlightningstorms.
Wherethemainsplugoranappliancecouplerisusedasthedisconnectdevice,
thedisconnectdeviceshallremainreadilyoperable.
Visibleandinvisiblelaserradiationwhenopen .Avoidexposur etobeam.
EN Print your user manual at www.philips.com/support ZH_CN
batteriesnearnakedÁamesor
࿎അĞಯཡࣞDVDᅌיࡱПቯᅿۡҠৄࢹடdඵሶᅿDVDᅌיࡱሽ༘ટ
սሢ൴ჩ؇ৄࢹႽҮົ ۦdѮ֕ࡩ๓འບӤࡘᇝDVD ᅌיࡱ൪
؇ົۦԄd
ಯཡࣞ
DVDᅌיࡱcႌে౸ࡩت՟ۄᅿࡧࡩ๓അ ᅙĥѩ৵ ሒ ൿ؇ ၿ ޝĦܚ
d
ᅿடᄊְ
DVDᅌיࡱdഀְDV D ᅌיࡱᅛฅcඣ౹ߦඛᄗႣບ؇འ
ບd
ಯཡְࣞ
DVDᅌיࡱۄᅿ๓تኒඃ҃൪୍d
تມ౹ࢹĩೊᅛְ
ࣞتᅙԎ໊ࡩඃ҃ߨ౸ᄊٰتඃ҃ ඪĩܠٰتඃ҃ჭসႽඪᄊd
ܠඃ҃חঙඪĩᅿস࣐ࢅӤস࣐؇ࡹޝ۷ൿdҧሒࡹޝd
ۥ
DVDᅌיࡱd
ဵչႊႬ߀൱ҬĶ౬٤ໝZZZSKLOLSVFRPVXSSRUW
យᝆ
ᜰᮓ
᭶ᮓ
џጒ
И
:
ࡉࣞᇛយᝆ English
ߍࣞ zˊஔ
DivXߍࣞ
᭶ᮓ :ᔡஔ
DVD ᖐӠ
ᔡஔ
2-2
1
AUDIO OUT L/R &
VIDEO OUT
3
2
DIGITAL OUT/
COAXIAL
DIGITAL IN
DVP3111/55:
Product overview
Main unit
a b c de f
a
Turn on the unit or switch to •
standby.
b Disc compartment
c Indicators
d IR sensor
Remote sensor.•
e
Open or close the disc •
compartment.
f
Start, pause or resume disc play.•
2-3
2-4
Remote control
u
t
s
r
q
p
o
n
m
MUTE
a
Turn on the DVD player or switch to •
standby mode.
b DISPLAY
Display the current play status or •
disc information
c Numeric Keypad 0 - 9
Select an item to play.•
d SEARCH
Start playback from designated point.•
e SETUP
Access or exit the setup menu.•
f
( Navigation buttons )
Navigate through the menus.•
Search fast-forward (right) or fast-•
backward (left).
Search slow-forward (up) or slow-•
backward (down).
OK
Confi rm an entry or selection.•
a
b
c
d
e
f
g
h
i
j
k
l
g
/ (Previous/Next )
Skip to the previous or nex t title, •
chapter, or track.
Press and hold for fast-backward or •
fast-forward search.
h ANGLE
Select a viewing angle of a DVD.•
Switch veiwing modes during playing •
JPEG slideshow.
i ZOOM
Zoom into or out of an image.•
j
MUTE
Mute or restore audio output.•
k STEP
Play video frame by frame.•
l SLOW
Select a slow forward.•
m REPEAT A-B
Repeat a specifi c section within a •
track/disc.
n REPEAT
Select or turn off repeat mode.•
o STOP
Stop play.•
p PLAY/PAUSE
Start, pause or resume disc play•
q SUBTITLE
Select a subtitle language for video.•
r AUDIO
Select an audio language or channel.•
s DISC MENU
Access or exit the disc menu.•
For VCD 2.0 and SVCD, turn on or •
off the PBC (playback control) mode.
t RETURN/TITLE
Returns to the previous menu.•
For DVD, navigates to title menu.•
For VCD version 2.0 or SVCD with •
PBC turned on, returns to the menu.
u
OPEN/CLOSE
Open or close the disc •
compartment.
DVP3300/93:
2-3
Product overview
Overview of the main unit
a b c gd e f
a (Standby-On)
Turn on the DVD player or switch to •
standby mode.
b Disc compartment
c Indicators
d
(Open/Close)
Open or close the disc •
compartment.
e
(Play/Pause)
Start, pause or resume disc play. •
Overview of the remote control
u
t
s
r
q
p
o
a
b
c
d
e
f
g
h
i
j
f
(USB jack)
Connect a USB flash drive.•
n
m
Remote control
a
Turn on the DVD player or switch to •
standby mode.
b
Display the current play status or •
disc information.
k
l
2-4
c Numeric Keypad 0 - 9
Select an item to play.•
d
Start playback from designated point.•
e
Access or exit the setup menu.•
f
(Navigation buttons)
Navigate through the menus.•
Search fast-forward (right) or fast-•
backward (left).
Search slow-forward (up) or slow-•
backward (down).
• OK
Confirm an entry or selection.•
g
/ (Previous/Next)
Skip to the previous or next title, •
chapter, or track.
Press and hold for fast-backward or •
fast-forward search.
h
Select a viewing angle of a DVD.•
Switch veiwing modes during playing •
JPEG slideshow.
q
r
s
t
u
Select a subtitle language for video.•
Select an audio language or channel.•
/
Access or exit the disc menu.•
For VCD 2.0 and SVCD, turn on or •
off the PBC (playback control) mode.
/
Returns to the previous menu.•
For DVD, navigates to title menu.•
For VCD version 2.0 or SVCD with •
PBC turned on, returns to the menu.
Open or close the disc •
compartment.
i
j
k
l
m
n
o
p
Zoom into or out of an image.•
Select USB device source.•
Play video frame by frame.•
Select a slow forward.•
A-B
Repeat a specific section within a •
track/disc.
Select or turn off repeat mode.•
Stop play.•
Start, pause or resume disc play•
DVP3300X/96
Product overview
Overview of the main unit
2-3
Overview of the remote control
a b c gd e f
a ( Standby-On )
Turn on the DVD player or switch to •
standby mode.
b Disc compartment
c Indicators
d iR sensor
Remote sensor.•
e
( Open/Close )
Open or close the disc compartment.•
f
g
( Play/Pause )
Star t, pause or resume disc play. •
( USB jack )
Connect a USB ash drive.•
u
t
s
r
q
p
o
n
m
USB
a
b
c
d
e
f
g
h
i
j
k
l
a
b DISPLAY
c Numeric Keypad 0 - 9
d SEARCH
Turn on the DVD player or switch to •
standby mode.
Display the current play status or disc •
information
Select an item to play.•
Star t playback from designated point.•
2-4
e SETUP
Access or exit the setup menu.•
( Navigation buttons )
f
Navigate through the menus.•
Search fast-for ward (right) or fast-•
backward (lef t).
Search slow-forward (up) or slow-•
backward (down).
OK
Con rm an entry or selection.•
/ ( Previous/Next )
g
Skip to the previous or next title, chapter, •
or track.
Press and hold for fast-backward or fast-•
forward search.
h ANGLE
Select a viewing angle of a DVD.•
Switch veiwing modes during playing •
JPEG slideshow.
i ZOOM
Zoom into or out of an image.•
j USB
k STEP
l SLOW
m REPEAT A-B
n REPEAT
o STOP
p PLAY/PAUSE
q SUBTITLE
r AUDIO
s DISC MENU
Select USB device source.•
Play video frame by frame.•
Select a slow forward.•
Repeat a speci c section within a track/disc.•
Select or turn off repeat mode.•
Stop play.•
Star t, pause or resume disc play•
Select a subtitle language for video.•
Select an audio language or channel.•
Access or exit the disc menu.•
For VCD 2.0 and SVCD, turn on or of f •
the PBC (playback control) mode.
t RETURN/TITLE
Returns to the previous menu.•
For DVD, navigates to title menu.•
For VCD ver sion 2.0 or SVCD with PBC •
turned on, returns to the menu.
u
OPEN/CLOSE
Open or close the disc compartment.•
3-1
Mechanical and Dismantling Instructions
Dismantling Instruction
The following guidelines show how to dismantle the player.
Step1: Remove 5 screws around the Top Cover, and then remove the Top Cover (Figure 1).
Detailed information please refer to the model set.
Figure 1
Step2: If it is necessary to dismantle Loader or Front Panel, the Front door should be removed first. (Figure 2)
Note: Make sure to operate gently otherwise the guider would be damaged.
Please kindly note that dismantle the front door
assembly carefully to avoid damage tray and the front door.
Figure 2
3-2
XP7 24Pin
XP9
XP3
XP2
Mechanical and Dismantling Instructions
Dismantling Instruction
Step3: If the tray can’t open in normal way, you can make it through the instruction as below (Figure 3).
Note: Make sure to operate gently otherwise the guider would be damaged.
Detailed information please refer to the model set.
Step4: Dismantling Front Panel, disconnect the connectors (XP3), need release 4 snaps of Front Panel
and 2 snaps of bottom cabinet , then gently pull the Panel out from the set. (Figure 4 - Figure 6)
Figure 3
Figure 4
Loading...