Philips CED-1900 Owners Manual
Always there to help you
Question?
Contact
Philips
Question?
Contact
Philips
Register your product and get support at
www.philips.com/welcome
CED1900
User manual 3
Руководство пользователя 41
1
Contents
1 Safety 4
8 Play from an iPod/iPhone 26
Compatible iPod/iPhone models 26
Connect your iPod/iPhone 26
Control play 27
Charge your iPod/iPhone 27
English
2 Your car entertainment system 5
Introduction 5
What's in the box 5
Overview of the main unit 6
Overview of the remote control 7
3 Install the car entertainment system 8
Connect wires 9
About the GPS antenna 12
Mount into the dashboard 12
4 Get started 14
Prepare the remote control 14
Turn on 14
Use the home menu 15
Set the date and time 16
Adjust the screen brightness 16
Switch display designs 16
5 Play from hard media 17
Load a disc 17
Connect a USB storage device 18
Insert an SD/SDHC card 18
Control play 18
Browse recorded les 20
About DivX
®
videos 20
9 Adjust sound 28
Adjust the volume level 28
Mute sound 28
Enable the maximum sound 28
Enable the DBB sound effect 28
Enable the FullSound effect 28
Select a preset sound equalizer 28
Others 29
10 Adjust settings 30
Access system setup menus 30
Adjust general settings 31
View system information 31
Adjust Navigation settings 32
11 Others 32
Play external audio/video input 32
Use rear monitors 33
Use buttons on the steering wheel 34
Set the rear view camera 34
Reset the system 35
Replace the fuse 35
Upgrade the rmware 35
12 Product information 36
6 Listen to radio 22
Switch to radio mode 22
Set up 22
Tune to a radio station 23
Store radio stations in memory 23
Tune to a preset radio station 23
Use RDS related features 23
7 Use the navigation system 25
Insert the map data card 25
Navigate your road trip 25
13 Troubleshooting 38
General 38
14 Notice 39
Compliance 39
Care of the environment 39
Trademark notice 39
Copyright 40
EN
3
1 Safety
Read and understand all instructions before you
use the device. If damage is caused by failure to
follow instructions, the warranty does not apply.
• Use of controls or adjustments or
performance of procedures other than
herein may result in hazardous radiation
exposure or other unsafe operation.
• The device is designed for negative ground
(earth) 12 V DC operation only.
• To reduce the risk of trafc accidents, do
not watch video when driving.
• To ensure safe driving, adjust the volume to
a safe and comfortable level.
• Improper fuses can cause damage or
re. When you need to change the fuse,
consult a professional.
• Use only the supplied mounting hardware
for a safe and secure installation.
• To avoid short circuits, do not expose the
device, remote control or remote control
batteries to rain or water.
• The device shall not be exposed to
dripping or splashing.
• Do not place any sources of danger on
the device (e.g. liquid lled objects, lighted
candles).
• Never insert objects into the ventilation
slots or other openings on the device.
• Never place any objects other than discs
into the disc tray/slot.
• To avoid exposure to laser radiation, do
not disassemble the device.
• Risk of damage to the screen! Never push,
rub or strike the screen with any object.
• Never use solvents such as benzene,
thinner, cleaners available commercially, or
anti-static sprays intended for discs.
• Clean the device with soft, damp cloth.
Never use substances such as alcohol,
chemicals or household cleaners on the
device.
• Risk of swallowing batteries! A coin
type battery is bundled, which can be
swallowed. Keep the battery out of reach
of children at all times!
4 EN
2 Your car
cd
What's in the box
entertainment
system
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With the car entertainment system, you can
• listen to music,
• watch videos,
• view pictures,
• listen to FM (RDS included) and AM/MW
radio, and
• navigate your road trip.
Check and identify the contents of the package:
a
ef g
h i
b
j
English
1 Main unit 2 Remote
control
3 ISO male connector
X 2
5 Screw X 4 (M5x8mm) 6 Hexagon
7 Remote control
battery
9 User manual 10 Quick start
4 Rubber
cushion
head screw
8 GPS antenna
guide
EN
5
Overview of the main unit
k
a
b
c
d
j
i
h
a
• Press to eject the disc.
b
• Press to access the navigation system.
• Press and hold to adjust the brightness
of LCD screen.
c
• Press to turn on the unit.
• Press and hold to turn off the unit.
• Press to mute the speakers or release
them from mute status.
d RESET
• Press to reset the system.
e
• Insert an SD/SDHC card.
f MAP
• Insert a microSD card that stores the
digital map data.
g iR sensor
• The sensor that receives infra-red
signals from the remote control.
e
f
g
h AV-IN
• Connect to the audio and video
output sockets of an external player by
a composite AV cable.
i
• Connect to a USB storage device or
iPod/iPhone.
j LCD screen
k +/-
• Press to increase or decrease the
volume.
6 EN
Overview of the remote
control
y
x
w
v
u
t
s
r
q
p
o
n
m
a SOURCE
• Press repeatedly to select a source.
b
• Press to eject the disc.
c
• Return to the previous menu or mode.
d VOLUME + / -
• Press to increase or decrease the
volume.
e
• Access the home menu.
f
• Enable or disable the maximum sound.
g
• Switch to video playback mode.
a
b
c
d
e
f
g
h
i
j
k
l
h
• Enable or disable the FullSound effect.
i DVD AUDIO
• Select an audio language or audio
channel.
j DBB
• Enable or disable the DBB (Dynamic
Bass Boost) sound effect.
k EQ
• Select a preset sound equalizer.
l MUSIC ZONE
• Select a music listening zone.
m
• Turn on or off the screen.
n
• Switch to the control interface for
front source or rear source.
o TOP MENU
• Return to top menu.
p DVD MENU
• Access the DVD menu.
q
• Switch to music playback mode.
r
• Switch to picture slideshow mode.
s
• Start, pause, or resume the play.
t OK
• Conrm an option.
u
/ /TRACK -/TRACK +
• Skip to the previous or next track,
chapter, or le.
• For DVD, press and hold to select a
speed for fast backward or forward
search.
v BAND
• Select a tuner band.
English
EN
7
w / /PRESET +/PRESET -
• Tune to the previous or next preset
radio station.
• Skip to the previous or next folder.
x
• Press to turn on the system.
• Press and hold to turn off the system.
• Press to mute the speakers or release
them from mute status.
y NAVI
• Press to access the navigation system.
3 Install the car
entertainment
system
Always follow the instructions in this chapter in
sequence.
These instructions are for a typical installation.
However, if your car has different requirements,
make the adjustment accordingly. If you have
any question regarding installation kits, consult
your local retailer.
Note
This system is designed for negative ground (earth) 12V
•
DC operation only.
• Always install this system in the car dashboard. Other
locations can be dangerous as the rear of the system
heats up during use.
• To avoid short-circuit: before you connect, make sure
that the ignition is off.
• Make sure that you connect the yellow and red power
supply leads after all other leads are connected.
• Make sure that all loose leads are insulated with
electrical tape.
• Make sure that the leads do not get caught under
screws iron parts that will move (e.g. seat rail).
• Make sure that all ground (earth) leads are run to a
common ground (earth) point.
• Use only the supplied mounting hardware for a safe
and secure installation.
• Improper fuses can cause damage or re. When you
need to change the fuse, consult a professional.
• When you connect other devices to this system, make
sure that the rating of the car circuit is higher than the
total fuse value of all the connected devices.
• Never connect speaker wires to the metal body or
chassis of the car.
• Never connect speaker wires with stripes to one
another.
8 EN
Connect wires
Note
Make sure that all loose leads are insulated with
•
electrical tape.
• Consult a professional to connect wires as instructed
below.
• Before connection, check the car's wiring carefully.
1 Connect the ISO male connectors.
ISO male connectors Connect to
1 Green strip, black-
edged green strip
2 White strip, black-
edged white strip
3 Gray strip, black-
edged gray strip
4 Purple strip, black-
edged purple strip
e Red strip Ignition key +12V
f Blue strip Motor/electric
g Blue strip, white strip Amplier relay
h Black strip Ground
Rear left speaker
Front left speaker
Front right speaker
Rear right speaker
DC when ON/ACC
antenna relay
control lead
control lead
ISO male connectors Connect to
i Yellow strip The +12V car
battery which is
energized at all times
2 Connect other wires if necessary.
Caution
To avoid an accident, the driver must not watch video
•
while driving. By design, this system disallows watching
video during drive. Park your car in a safe place and
engage the parking brake before watching video.
Note
When the parking brake of your vehicle is not engaged,
•
the video blocking system is activated. It blocks the
display of front video source only.
• If the system is not properly connected with the
parking brake control module of your vehicle, video
signals will be blocked by the system, with the below
message displayed on the TFT.
Connectors and
sockets on rear panel
1 For ISO male
connectors
2 REAR OUT L (White
socket)
3 REAR OUT R (Red
socket)
4 FRONT OUT R (Red
socket)
5 FRONT OUT L
(White socket)
External sockets or
connectors
As indicated
above
Rear left speaker
Rear right speaker
Front right
speaker
Front left speaker
English
EN
9
Connectors and
sockets on rear panel
6 VIDEO OUT 1
(Yellow socket)
External sockets or
connectors
Video input
socket of an
external display
device
7 VIDEO OUT 2
(Yellow socket)
Video input
socket of an
external display
device
8 VIDEO IN (Yellow
socket)
Video output
socket of an
external player
9 CAMERA IN (Purple
socket)
Video output
socket of an
external camera
10 SUB-W OUT (Blue
Sub-woofer
socket)
11 AV-IN L (White
socket)
Left audio channel
output socket of
an external player
12 AV-IN R (Red socket) Right audio
channel output
socket of an
external player
13 REVERSE CAMERA
(Purple wire)
14 PARKING BRAKE
Reverse camera
(B+)
Parking brake (-)
(Pink wire)
15 OE SWC IR
REMOTE IN (Brown
OE SWC remote
in
wire)
16 OE SWC IR
Ground
REMOTE IN (Black
wire)
17 OE SWC AD LEARN
(White wire)
18 OE SWC AD LEARN
(White wire)
19 OE SWC AD LEARN
OE SWC AD
Learn line 1
OE SWC AD
Learn line 2
Ground
(Black wire)
Connectors and
sockets on rear panel
20 EXTERNAL BOX
CONNECTOR (Black
External sockets or
connectors
External
navigation box
connector)
21 GPS AERIAL (Black
connector)
22 RADIO ANTENNA
GPS smart
antenna
Radio antenna
(Black connector)
23 Rear Monitor
Audio Out 1 (White
connector)
24 Rear Monitor
Audio Out 1 (Red
connector)
Left audio channel
input socket of
one rear monitor
Right audio
channel input
socket of one rear
monitor
25 Rear Monitor
Audio Out 2 (White
connector)
Left audio channel
input socket of
another rear
monitor
26 Rear Monitor
Audio Out 2 (Red
connector)
Right audio
channel input
socket of another
rear monitor
Tip
The pin arrangement for the ISO connectors depends
•
on the type of your vehicle. To avoid damage to the
system, connect properly.
10 EN
kl
z
y
x
w
v
u
t
p
o
n
m
s
r
q
English
a
bcde fgh ij
EN
11
About the GPS antenna
Warning
•
Risk of injury: Never install the antenna and its
accessories on the airbag cover.
• Risk of swallowing parts: Keep the antenna and
accessories out of the reach of children.
Caution
Risk of electromagnetic interference: Do not install the
•
GPS antenna over any sensors or vents.
• Risk of short circuit, malfunction, or damage to your car
navigation system: Do not alter the GPS antenna cable
or dismantle the antenna box.
• Risk of poor reception: Use the supplied metal sheet
only, and never cut or distort it; do not paint the GPS
antenna.
• Risk of damage to the GPS antenna cable: Never pull
the antenna cable when you remove the antenna.
• Risk of scratching your car: The GPS antenna box has
a magnet. When you install or remove it, do not drag it
on any metal surface.
Note
Make sure that the contact surface that contacts with
•
the metal sheet is free of moisture, dust, grime, oil, and
any other dirt.
• If you remove the metal sheet, some adhesive may be
left on the contact surface.
b
a
c
Connect the GPS antenna
a b
GPS AERIAL
1 Connect the GPS antenna to your car
navigation system.
2 Use the supplied screw to fasten the
connectors.
Install the GPS antenna
You can install the signal receptor of GPS
antenna:
• On the dashboard cover
• On the back panel of rear-view mirror
12 EN
1 Remove the protective cover of the metal
sheet, and then afx it.
2 Afx the antenna box onto the metal
sheet.
3 Use clamps to secure the antenna cable.
Mount into the dashboard
Note
Make sure that wires are correctly connected before
•
you mount the main unit into a car.
• If preset radio stations are lost when the ignition key
is turned OFF and then back ON, reconnect the red
leads crosswise to the yellow ones.
1 If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
• If you disconnect the car battery in
a car that has an on-board drive or
navigation computer, the computer
may lose its memory.
• If the car battery is not disconnected,
to avoid short-circuit, make sure that
bare wires do not touch each other.
2 Make sure that the car dashboard opening
is within these measurements:
3 Slide the unit into the dashboard until a
click sound is heard.
English
5 mm
182 mm
112 mm
• Since the unit cannot be used if the
dashboard opening's slant angle is
above 20 degrees, make sure that the
horizontal slant of the car dashboard
opening is between 0 and 20 degrees.
4 Reconnect the negative terminal of the car
battery.
EN
13
Loading...