Philips CE130/51 User guide
Register your product and get support at
www.philips.com/welcome
CE131
EN User manual 3
ES-AR Manual del usuario 23
PT-BR Manual do Usuário 43
=+7: Ԛʹ˫
=+&1 Ⴌ߀൱Ҭ
Contents
Rear Aux 18
Reset 18
8 Additional information 18
1 Important 4
Safety 4
Notice 4
2 Your car audio system 6
Introduction 6
What’s in the box 6
Overview of the main unit 7
3 Get started 8
Install the car audio 8
Turn on 12
Set clock 12
Detach the front panel 18
Replace fuse 18
Remove the unit 19
9 Product information 19
10 Troubleshooting 20
11 Glossary 21
4 Listen to radio 12
Tune to a radio station 12
Store radio stations in memory 13
Tune to a preset station 13
5 Play audio files 13
Play from USB 13
Insert a card 13
Play options 14
Connect external sound source 15
English
6 Adjust sound 15
Adjust volume 15
Mute 15
Turn Dynamic Bass Boost (DBB) on/off 15
Tunr on/off max sound 15
Select preset equalizer 16
Switch music listening zone 16
Other sound settings 16
7 Adjust system settings 17
Turn beep sound on/off 17
Select blackout setting 17
Turn demo mode on/off 17
Dimmer 17
Dance 17
EN
3
1 Important
Safety
The apparatus shall not be exposed to •
dripping or splashing.
Do not place any sources of danger on •
the apparatus (e.g. liquid filled objects,
lighted candles).
Read and understand all instructions •
before you use your apparatus. If damage
is caused by failure to follow instructions,
the warranty does not apply.
This apparatus is designed for negative •
ground (earth) 12 V DC operation only.
To ensure safe driving, adjust the volume •
to a safe and comfortable level.
Improper fuses can cause damage or •
fire. When you need to change the fuse,
consult a professional.
Use only the supplied mounting hardware •
for a safe and secure installation.
To avoid short circuit, do not expose the •
apparatus, remote control or remote
control batteries to rain or water.
Never insert objects into the ventilation •
slots or other openings on the apparatus.
Clean the apparatus and frame with a •
soft, damp cloth. Never use substances
such as alcohol, chemicals or household
cleaners on the apparatus.
Never place any objects other than discs •
into the apparatus.
Never use solvents such as benzene, •
thinner, cleaners available commercially,
or anti-static sprays intended for discs.
Visible and invisible laser radiation when •
open. Avoid exposure to beam.
Risk of damage to the apparatus screen! •
Never touch, push, rub or strike the
screen with any object.
Caution
Use of controls or adjustments or •
performance of procedures other than herein
may result in hazardous radiation exposure or
other unsafe operation.
Notice
The making of unauthorized copies of
copy-protected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offence.
This equipment should not be used for such
purposes.
Windows Media and the Windows logo are
trademarks, or registered trademarks of
Microsoft Corporation in the United States
and/or other countries.
This apparatus includes this label:
Recycling
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
4
EN
When you see the crossed-out wheel bin
symbol attached to a product, it means the
product is covered by the European Directive
2002/96/EC:
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products. The correct
disposal of your old product helps prevent
potentially negative consequences on the
environment and human health.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed of with normal household
waste.
Please inform yourself about the local rules on
separate collection of batteries. The correct
disposal of batteries helps prevent potentially
negative consequences on the environment
and human health.
Any changes or modifications made to this
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
2011 © Koninklijke Philips Electronics N.V. All
rights reserved.
Specifications are subject to change without
notice. Trademarks are the property of
Koninklijke Philips Electronics N.V. or their
respective owners. Philips reserves the right
to change products at any time without being
obliged to adjust earlier supplies accordingly.
English
This product complies with the radio
interference requirements of the European
Community.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and
old equipment.
EN
5
2 Your car audio
system
h Disassembly tools x 2 pcs
i User manual
j Quick start guide
Congratulations on your purchase, and
welcome to Philips! To fully benefit from the
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With the in-car audio system, you can enjoy
your drive while listening to:
FM or AM (MW) radio•
Audio from USB devices•
Audio from SD/SDHC card•
Audio from other external devices•
The unit supports the following media format:
b
e
a
cd
f
g
jih
What’s in the box
Check and identify the contents of your
package:
a Main unit (with a sleeve)
b Front panel
c Trim p l a te
d Carrying case
e ISO male connector
f Rubber cushion
g Screws x 4 pcs
6
EN
Overview of the main unit
adc
b
e
f
g
English
p
a SOURCE
b MENU
c
d
r
Select audio source.•
Access system menu.•
Return to previous menu.•
/
n
q
mo
e ZONE /
l
k
Turn the unit on or off.•
Confirm selection.•
Mute or unmute sound.•
Rotate to adjust volume.•
Select tuner band. •
Select MP3/WMA folder.•
Switch music listening zone.•
ji
h
EN
7
f MP3 LINK
Connect external audio device.•
g
Unlock the panel.•
h
USB socket.•
6281'
i
Turn on or off Maximizing volume.•
View clock.•
j DBB
Turn on or off Dynamic Bass Boost •
(DBB) sound.
Access to tuner auto store.•
k
Start play.•
Pause or resume play.•
l RPT / SHUF
Access to repeat play.•
Access to random play.•
m
/
Search for track/folder.•
n
/
Tune for radio station.•
Skip/search for track.•
Fast forward/backward playback.•
o DISP
Display current status. •
p EQ / AUDIO
Select equalizer (EQ) setting.•
Access audio setting menu.•
q RESET
Restore default settings.•
r SD card slot
3 Get started
Caution
Use the controls only as stated in this user •
manual.
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of your apparatus. The
model number and serial number are on the
bottom of your apparatus. Write the numbers
here:
Model No. __________________________
Serial No. ___________________________
Install the car audio
These instructions are for a typical installation.
However, if your car has different requirements,
make the corresponding adjustment. If you have
any questions regarding installation kits, consult
your Philips car audio dealer.
Caution
This unit is designed for negative ground •
(earth) 12 V DC operation only.
Always install this unit in the car dashboard.
•
Other locations can be dangerous as the rear
of the unit heats up during use.
•
To avoid short-circuit: before you connect,
ensure that the ignition is off.
Ensure that you connect the yellow and red
•
power supply leads after all other leads are
connected.
Ensure that all loose leads are insulated with
•
electrical tape.
Ensure that the leads do not get caught under
•
screws orin parts that will move (e.g. seat rail).
Ensure that all ground (earth) leads are run to
•
a common ground (earth) point.
Use only the supplied mounting hardware for a
•
safe and secure installation.
Improper fuses can cause damage or fire.
•
When you need to change the fuse, consult a
professional.
8
EN
Note on the power supply lead (yellow)
When you connect other devices to this •
system, ensure that the rating of the car
circuit is higher than the total fuse value
of all the connected devices.
Notes on speaker connection
Never connect speaker wires to the •
metal body or chassis of the car.
Never connect speaker wires with stripes •
to one another.
aa
b
c
d
a
b
c
d
e
f
g
h
i
a
English
b
c
d
b
c
d
Connect wires: ISO male connectors
Caution
Ensure that all loose leads are insulated with •
electrical tape.
Note
Consult a professional to connect CE131 as •
instructed below.
1 Connect the supplied male connector to
the unit.
1Green/black
strip
2 White/black
strip
3 Gray/black
strip
4Purple/black
strip
e Red Ignition key +12V DC
f Blue Motor/electric antenna
gBlackGround
h Orange/
White
i Yellow To the +12V car
Left speaker (Rear)
Left speaker (Front)
Right speaker (Front)
Right speaker (Rear)
when ON/ACC
relay control lead/
Amplifier relay control
lead
Illumination switch
battery which is
energized at all times
2 Check the car’s wiring carefully and
connect them to the supplied male
connector.
Note
Risk of danger! Please consult a professional to •
perform the below steps!
EN
9
3 Connect the antenna and amplifier as
illustrated, if applicable.
f
g
L
L
Rear
Rear
R
R
h
Front
Front
Mount into the dashboard
1 If the car does not have an on-board
i
drive or navigation computer, disconnect
the negative terminal of the car battery.
If you disconnect the car battery in •
a car that has an on-board drive or
navigation computer, the computer
may lose its memory.
If the car battery is not disconnected, •
to avoid short-circuit, ensure that the
bare wires do not touch each other.
2 Ensure that car dashboard opening is
within these measurements:
Connector Connect to
1 ANTENNA Antenna
2 FRONT LINE OUT
R (Socket)
3 FRONT LINE OUT
L (Socket)
4 REAR LINE OUT R
(Socket)
5 REAR LINE OUT L
(Socket)
6 OE REMOTE (Pink) OE Remote
7TEL MUTING
(Orange)
8 SUBWOOFER
(Blue)
9 REAR AUX (Yellow) Aux right/left
Tip
The pin arrangement for the ISO connectors •
depends on the type of vehicle you drive. Be
sure to make proper connections to prevent
damage to the unit.
Front right
speaker
Front left
speaker
Rear right
speaker
Rear left
speaker
To c e l lular
phone system
Subwoofer
5mm
183 mm
53mm
3 Remove the mounting sleeve with the
supplied disassembly tools.
10
EN
4 Install the sleeve into the dashboard and
bend the tabs outward to fix the sleeve.
Note
If the unit is not fixed by sleeve but by the •
supplied screws, skip this step.
53.5 mm
183 mm
5 Place the supplied rubber cushion over
the end of the mounting bolt.
English
7 Reconnect the negative terminal of the
car battery.
Attach the front panel
1 Attach the trim plate.
6 Slide the unit into the dashboard until you
hear a click sound.
EN
11
2 Insert the left side of the panel in the
chassis until it is correctly engaged.
3 Press the right side of the panel until it is
locked into place.
Turn on
4 Listen to radio
Tune to a radio station
1 Press SOURCE repeatedly to select radio
mode.
2 Press ZONE / repeatedly to select
band: [FM1], [FM2], [FM3], [AM1], or
[AM2] .
3 Press and hold or to tune to a
radio station manually.
The radio station is broadcast. »
To search for a radio station »
automatically, press
or .
To turn on the unit,
.
Press •
To turn off the unit,
press and hold •
turned off.
until the unit is
Set clock
1 Press MENU repeatedly until current
time is flashed.
2 Rotate to set hour.
3 Press to confirm.
4 Rotate to set minute.
5 Press to confirm.
View clock
In any mode, press and hold MAX SOUND
until the clock is displayed.
Press any key to cancel the clock •
display.
Select tuner region
You can select suitable country/region of the
radio.
1 Press SOURCE to select radio mode.
2 Press MENU repeatedly until [ARE A] is
displayed..
3 Rotate to select:
[• EUR] (Western Europe)
[• RUS] (Russia)
[• ASI] (Asia Pacific)
[• USA] (United States)
[• LAT] (Latin America)
Select tuner sensitivity
To receive more radio stations or only
stations with strong signal, you can adjust the
tuner sensitivity.
1 Press MENU repeatedly until [LOCAL] is
displayed.
12
EN
2 Rotate to select a setting:
• [LOCAL ON] (local on): Only
stations with strong signal can be
broadcast.
• [LOCAL OFF] (local off): Stations
with strong and weak signals can be
broadcast.
Store radio stations in
memory
5 Play audio files
English
Play from USB
Note
Ensure that the USB device contains playable •
music.
You can store up to 6 stations in each band.
Store stations automatically
1 In Radio mode, press and hold DBB until
[STORE - - -] is displayed.
2 Press to confirm.
The six strongest stations of the »
selected band are saved in preset
channel automatically.
Store stations manually
1 Tune to a station that you want to store.
(see ‘Tune to a radio station’ on page 12)
2 Press a numeric button for 3 seconds.
The station is saved in the selected »
channel.
Tune to a preset station
1 Press ZONE / to select band.
2 Press the numeric button to select a
preset station.
Insert the USB device
1 Slide the USB socket cover marked
to the left.
2 Insert the USB device into the USB
socket.
The unit starts to play from the USB »
device automatically.
Remove the USB device
1 Press to turn off the unit.
2 Remove the USB device.
Insert a card
Note
This unit supports SD and SDHC cards. •
1 Press to release the panel.
2 Push the left side of the panel rightward,
then pull the panel towards you to
disengage it from the chassis.
EN
13
3 Insert the card into the card slot.
The unit starts playing from the card »
automatically.
Search in other folder
1 Press .
The name of the current folder is »
displayed.
2 Rotate to navigate through all folders.
3 Press to access the selected folder.
4 Rotate to select a track in the folder.
5 Press to start play.
Tip
To go back to upper level of a folder, press • .
Remove the card
1 Press to turn off the unit.
2 Press the card until you hear a click
sound.
The card is now disengaged. »
3 Remove the card.
Play options
To pause, press • .
To resume play, press • again.
To skip to the previous/next track, press •
/ .
To search backward/forward rapidly •
within the current track, press /
for 3 seconds.
Search for an MP3/WMA track
Search within the current folder
1 Press .
The name of the current track is »
displayed.
2 Rotate to select anther track in current
folder.
3 Press to confirm.
View play information
During playing, press DISP repeatedly to view:
Track number and elapsed play time•
Folder •
File •
Album•
Artist•
Title•
Repeat play
1 During play, press RPT.
» [REP] is displayed.
2 Rotate to select a setting.
• [RPT TRK] (repeat one track): play
current track repeatedly.
• [RPT FLD] (repeat a folder): play all
tracks in the current folder repeatedly.
• [RPT ALL] (repeat all tracks): play all
tracks repeatedly.
Random play
You can play the tracks in random order:
1 During play, press SHUF.
» [SHUF] is displayed.
14
EN
Loading...