Philips BDL4221V, BDL4221V-27B User Manual

Manual

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/MANUAL.HTM2006-03-10 1:33:25 PM

Safety & Troubleshooting

Safety and Troubleshooting Information

Safety Precautions and Maintenance • FAQs • Troubleshooting • Regulatory Information • Other Related Information

Safety precautions and maintenance

WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards.

Read and follow these instructions when connecting and using your computer monitor:

● Unplug the monitor if you are not going to use it for an extensive period of time.

● Unplug the monitor if you need to clean it with a slightly damp cloth. The screen many be

wiped with a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based liquids.

● Consult a service technician if the monitor does not operate normally when you have

followed the instructions in this manual.

● The casing cover should be opened only by qualified service personnel.

● Keep the monitor out of direct sunlight and away from stoves or any other heat source.

● Remove any object that could fall into the vents or prevent proper cooling of the monitor’s

electronics.

● Do not block the ventilation holes on the cabinet.

● Keep the monitor dry. To avoid electric shock, do not expose it to rain or excessive moisture.

● If turning off the monitor by detaching power cable or DC power cord, wait for 6 seconds

before attach the power cable or DC power cord for normal operation.

● To avoid the risk of shock or permanent damage to the set do not expose the monitor to rain

or excessive moisture.

● When positioning the monitor, make sure the power plug and outlet are easily accessible.

● IMPORTANT: Always activate a screen saver program during your application. If a still

image in high contrast remains on the screen for an extended period of time, it may leave an 'after-image' or 'ghost image' on the front of the screen. This is a well-known phenomenon that is caused by the shortcomings inherent in the LCD technology. In most cases the afterimage will disappear gradually over a period of time after the power has been switched off. Be aware that the after-image symptom cannot be repaired and is not covered under warranty.

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/SAFETY/SAFETY.HTM (1 of 2)2006-03-10 1:33:37 PM

Safety & Troubleshooting

Consult a service technician if the monitor does not operate normally when the operating instructions given in this manual have been followed.

RETURN TO TOP OF THE PAGE

Installation Locations

● Avoid exposure to heat and extreme cold

● Do not store or use the product in locations exposed to heat, direct sunlight or extreme cold.

● Avoid moving the product between locations with large temperature differences. Choose a

site that falls within the following temperature and humidity ranges.

❍ Temperature: 0-35°C 32-95°F ❍ Humidity: 20-80% RH

● Do not subject the product to severe vibration or high impact conditions. Do not place the

product inside a car boot.

● Take care not to mishandle this product by either knocking or dropping during operation or

transportation.

● Do not store or use the product in locations where there is a high level of humidity or in dusty

environments. Do not allow water or other liquids to spill on or into the product.

RETURN TO TOP OF THE PAGE

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/SAFETY/SAFETY.HTM (2 of 2)2006-03-10 1:33:37 PM

About This Manual

About This Guide • Notational Descriptions

About This Guide

This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It describes the features, setup, operation and other important information.

It includes the following sections:

● Safety and Troubleshooting Information provides tips and solutions for common problems as

well as other related information you may need.

● About This Electronic User's Manual gives an overview of information included, along with

notation icon descriptions and other documentation for your reference.

● Product Information gives an overview of the monitor's features as well as the technical

specifications for this monitor.

● Installing Your Monitor describes the initial setup process and gives an overview of how to

use the monitor.

● On-Screen Display provides information on adjusting the settings on your monitor.

● Remote Control provides information on adjusting the settings for your Monitor.

● Customer Care and Warranty contains a list of worldwide Philips Consumer Information

Centres along with help desk phone numbers and information on the warranty applicable to your product.

● Download and Print Option transfers this entire manual to your hard drive for easy reference.

RETURN TO TOP OF THE PAGE

Notational Descriptions

The following subsections describe notational conventions used in this document.

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/ABOUT/ABOUT.HTM (1 of 2)2006-03-10 1:33:37 PM

About This Manual

Notes, Cautions and Warnings

Throughout this guide blocks of text may be accompanied by an icon and printed in bold or italic type. These blocks contain notes, cautions or warnings. They are used as follows:

NOTE: This icon indicates important information and tips that help you make better use of your computer system.

CAUTION: This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data.

WARNING: This icon indicates the potential for bodily harm and tells you how to avoid the problem.

Some warnings may appear in alternate formats and may not be accompanied by an icon. In such cases, the specific presentation of the warning is mandated by the relevant regulatory authority.

RETURN TO TOP OF THE PAGE

All rights reserved. Reproduction, copying, use, modification, hiring, renting, public performance, transmission and/or broadcasting in whole or in part is prohibited without written consent of Philips Electronics N.V.

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/ABOUT/ABOUT.HTM (2 of 2)2006-03-10 1:33:37 PM

Product Information

Product Features • Lead-free Product • Technical Specifications • Resolution & Preset Modes • Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views • Serial Interface Comunication Protocol

Product Features

BDL4221V

● Less management effort for maximum productivity

❍ Multiple displays form a daisy chain to show uniform ❍ Monitor is network controllable for remote management ❍ Input connectors: CVBS, S-video, SCART, and YPbPr.

● Better front of screen experience

❍ Motion adaptive deinterlacing for razor sharp images ❍ 3D comb filter separates color for a razor-sharp image ❍ WXGA, wide format 1366 x 768 resolution for sharper display ❍ Adaptive brightness intensifier technology

● Great convenience

❍ Zoom function to enable tiled matrix application ❍ Support hight-bandwidth digital content protection decryption ❍ Split screen for dual video/PC display ❍ Picture in picture for public display

RETURN TO TOP OF THE PAGE

Lead-free Product

Philips eliminated toxic substances like lead from its displays. Lead-free display helps protect your health and promotes environmentally sound recovery and disposal of waste from electrical and electronic equipment.Philips complies with the European Community stringent RoHS Directive mandating restrictions on hazardous substances in electrical and electronic equipment. With Philips, you can be confident that your display device does not harm the environment.

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/PRODUCT/product.htm (1 of 10)2006-03-10 1:33:39 PM

Product Information

Technical Specifications*

LCD PANEL

• Type TFT LCD

• Screen size 42"

• Pixel Pitch 0.227 x 0.681 mm

• LCD Panel type

1366 x 768 pixels R.G.B. vertical stripe Hard coating surface, anti-glare polarizer

• Effective viewing area 930.25 x 523.01 mm

• Display Colors 8 bits interface (16.7M colors)

PC SCANNING

• Vertical refresh rate 56Hz-75Hz

• Horizontal frequency 30kHz-63kHz

PC VIDEO

• Video dot rate < 85 MHz

• Input impedance

- Video

75 ohm

- Sync

2.2K ohm

• Input signal levels 0.7 Vpp

• Sync input signal

Separate sync

• Sync polarities Positive and negative

• Input Frequency

WXGA Hsync 48 kHz, Vsync 60 Hz (N.I.) SVGA Hsync 38 kHz, Vsync 60 Hz (N.I.) VGA/DVI-D Hsync 31 kHz, Vsync 60 Hz (N.I.)

• Video interface

D-sub, S-Video, SCART composite, components video, and DVI-D

AUDIO

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/PRODUCT/product.htm (2 of 10)2006-03-10 1:33:39 PM

Product Information

• Input level for PC/SVHS/SCART 500 mV nominal

• Loudspeaker 10W Stereo Audio (200Hz~10kHz, 8 ohm, 10% THD)

OPTICAL CHARACTERISTICS

• Contrast ratio 1100:1 (with DCR on)

• Brightness

500 cd/m

(typ.)

• Peak contrast angle 6 o'clock

• White Chromaticity

x: 0.283 y: 0.297 (at 9300°K) x: 0.313 y: 0.329 (at 6500°K) x: 0.328 y: 0.344 (at 5700°K)

• Viewing Angle (C/R >5)

Upper >89° (typ.) Lower >89° (typ.) Left >89° (typ.) Right >89° (typ.)

• Response time (G to G) 8 ms(typ.) 12 ms(max.)

sRGB

sRGB is a standard for ensuring correct exchange of colors between different devices (e.g. digital cameras, monitors, printers, scanners, etc.)

Using a standard unified color space, sRGB will help represent pictures taken by an sRGB compatible device correctly on your sRGB enabled Philips monitors. In that way, the colors are calibrated and you can rely on the correctness of the colors shown on your screen.

Important with the use of sRGB is that the brightness and contrast of your monitor is fixed to a predefined setting as well as the color gamut. Therefore it is important to select the sRGB setting in the monitor's OSD.

To do so, at PC mode, open the OSD by pressing the MENU button of your monitor. Use the down button to go to COLOR SETTINGS and press MENU again. Then move the down button to go to NORMAL COLOR and press MENU again.

* This data is subject to change without notice.

RETURN TO TOP OF THE PAGE

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/PRODUCT/product.htm (3 of 10)2006-03-10 1:33:39 PM

Product Information

Resolution & Preset Modes

• Recommended 1360 x 768 at 60Hz

10 factory preset modes:

Resolution Mode H. freq (kHz) V. freq (Hz)

640x350 VGA-1 31.469 70.086 640x480 VGA VESA 60 31.469 59.940 640x480 VGA VESA 75 37.500 75.000 720x400 IBM VGA 3H 31.468 70.087 800x600 SVGA VESA 56 35.156 56.250 800x600 SVGA VESA 60 37.879 60.317

800x600 SVGA VESA 75 46.875 75.000 1024x768 XGA VESA 60 48.363 60.004 1024x768 XGA VESA 75 60.023 75.029 1280x768 CVT 47.700 60.000 1280x720 CVT 44.772 59.855 1360x768 VESA 47.700 60.000

Video

720x480 480i 15.734 59.940

720x576 576i 15.625 50.000

720x480 480p 31.470 60.000

720x576 576p 31.250 50.000 1280x720 720p 37.500 50.000 1280x720 720p 45.000 60.000

1920x1080 1080i 28.125 50.000 1920x1080 1080i 33.750 60.000

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/PRODUCT/product.htm (4 of 10)2006-03-10 1:33:39 PM

Product Information

RETURN TO TOP OF THE PAGE

Automatic Power Saving

If you have VESA DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will then 'wake up' automatically. The following table shows the power consumption and signaling of this automatic power saving feature:

Power Management Definition

VESA Mode Video H-sync V-sync Power Used LED color

Active On Yes Yes 100 W (typ.) Blue

Sleep Off No No < 5 W Amber

Switch Off Off - - < 3 W Off

RETURN TO TOP OF THE PAGE

Physical Specifications

• Dimension (WxHxD) *

incl. Pedestal, Speakers: 1272mm x 680mm x 300mm (49" x

26.7" x 11.8") w/o Pedestal, Speakers: 1052mm x 644mm x 150mm (41.3" x 25.3" x 5.9")

• Weight 35 kg (incl. Pedestal, Speakers)

• Power supply 100 — 240VAC, 60 — 50Hz

• Power consumption 140 W (typ.)

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/PRODUCT/product.htm (5 of 10)2006-03-10 1:33:39 PM

Product Information

• Temperature (operating) 5° C to 35° C

• Relative humidity 20% to 80%

• System MTBF

50K hrs (excluding CCFL 50Khrs)

* This data is subject to change without notice.

RETURN TO TOP OF THE PAGE

Pin Assignment

1. The digital only connector (DVI-D) contains 24 signal contacts organized in three rows of eight contacts. Signal pin assignments are listed in the following table:

No.

Signal Assignment

No.

Signal Assignment

Pin No.

Signal Assignment

T.M.D.S. Data2-

T.M.D.S. Data1- 17 T.M.D.S. Data0-

T.M.D.S. Data2+

T.M.D.S. Data1+ 18 T.M.D.S. Data0+

T.M.D.S. Data2/4 Shield

T.M.D.S. Data1/3 Shield

T.M.D.S. Data0/5 Shield

No connect

No connect 20 No connect

No connect

No connect 21 No connect

DDC Clock

+5V Power 22

T.M.D.S. Clock Shield

DDC Data

Hot Plug Detect 23 T.M.D.S. Clock+

No connect 16 Ground (for +5V) 24 T.M.D.S. Clock-

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/PRODUCT/product.htm (6 of 10)2006-03-10 1:33:39 PM

Product Information

2. The 15-pin D-sub connector (male) of the signal cable:

No.

Assignment

No.

Assignment

Red video input

DDC +5V

Green video input

Cable detect

Blue video input

Identical output, connected to pin 10

Ground

Serial data line (SDA)

H. Sync / H+V

Red video ground

V. Sync

Green video ground

Data clock line (SCL)

Blue video ground

3. RS232 Connector

D-sub 9-pin male connector for communication with plasma engine or PC.

Pin No.

RS-232 (EIA-232-A) Function

3 Transmit Data (TD) from DTE to DCE 2 Receive Data (RD) from DCE to DTE 7 Request to Send (RTS) 8 Clear to Send (CTS)

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/PRODUCT/product.htm (7 of 10)2006-03-10 1:33:39 PM

Product Information

6 DCE Ready (DSR) 5 Signal Ground (SG) 1 Received Line Signal Detector (DCD) 4 DTE Ready (DTR) 9 Ring Indicator

4. SCART Connector

No.

Signal Pin

No.

Audio right channel output (0.5 Vrms, < 1K ohms)

Audio right channel input (0.5 Vrms, > 10K ohms)

Audio left channel output (0.5 Vrms, < 1K ohms)

4 Audio ground 4 5 Blue signal ground 5

Audio left channel input (0.5 Vrms, > 10K ohms)

7 Blue signal I/O (0.7 Vp-p, 75 ohms) 7

Function switching I/O (L: < 2V, H: > 10V, 10K ohms)

9 Green signal ground 9 10 Intercommunication data line No. 1 10 11 Green signal I/O (0.7 Vp-p, 75 ohms) 11

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/PRODUCT/product.htm (8 of 10)2006-03-10 1:33:39 PM

Product Information

12 Intercommunication data line No. 2 12 13 Red signal ground 13 14 Blanking signal ground 14 15 Red signal I/O (0.7 Vp-p, 75 ohms) 15

Blanking signal I/O (L: < 0.4V, H: >1.0V, 75 ohms)

17 Composite video signal ground 18 18 Blanking signal ground 17

Composite video signal output (1 Vp-p, 75 ohms, sync: negative)

Composite video signal input (1 Vp-p, 75 ohms, sync: negative)

21 Plug shield (common ground) 21

RETURN TO TOP OF THE PAGE

Product Views

Follow the links to see various views of the monitor and its components.

Product Description

Serial Interface Comunication Protocol

Link

SICP Protocol.pdf

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/PRODUCT/product.htm (9 of 10)2006-03-10 1:33:39 PM

Product Information

RETURN TO TOP OF THE PAGE

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/PRODUCT/product.htm (10 of 10)2006-03-10 1:33:39 PM

Installing your LCD Monitor

Product Description • Connecting to Your PC, DVD/VCR etc. • Getting Started • Optimizing Performance

Product Description

Installing your LCD Monitor

Side View (Left)

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/INSTALL/install.htm (1 of 5)2006-03-10 1:33:39 PM

Installing your LCD Monitor

INPUT

Selecting input source

Increase or decrease the channel number or moving up or down to highlight the function in OSD

Increase or decrease the level of audio volume or moving left or right to highlight the sub-menu in the selected function of OSD

Open the OSD or confirm the selected function

DC power switch On/Off

RETURN TO TOP OF THE PAGE

Side View (Right)

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/INSTALL/install.htm (2 of 5)2006-03-10 1:33:39 PM

Installing your LCD Monitor

1 Audio input for composite input

Audio (left and right) in put for compo site

signal in put. 2 Composite input Composite (CVBS) signal input 3 S-Video input S-Video signal input 4 Earphone output Earphone output

RETURN TO TOP OF THE PAGE

Rear View

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/INSTALL/install.htm (3 of 5)2006-03-10 1:33:39 PM

Installing your LCD Monitor

1 AC in AC power in 2 AC power AC power switch

3 Speakers output External speakers output 4 D-Sub output PC analog D-Sub output

5 DVI-D input PC digital input 6 D-Sub input PC analog D-Sub input 7 RS232 input RS232 network connection Input

8 RS232 output

RS232 network connection output for the use of loop through function

9 PC audio PC stereo audio input

10 Audio input for component signal

Audio (left and right) input for component signal input

11 Component input

Component (YP

bPr

) signal input

12 Composite output

Composite (CVBS) output for the use of loop through function

13 Audio output for composite output

Audio (left and right) out put for compo site signal out put.

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/INSTALL/install.htm (4 of 5)2006-03-10 1:33:39 PM

Installing your LCD Monitor

14 External / EURO-AV

SCART connection (for the use of European model only)

15 Kensington lock Kensington lock

Optimising Performance

● For best performance, ensure that your display settings are set at 1360x768, 60Hz.

Note: You can check the current display settings by pressing the 'MENU' button

once.

● You can also install the Flat Panel Adjust (FP Adjust) program, a program for getting the best performance

out of your monitor. This is included on this CD. Step-by-step instructions are provided to guide you through the installation process. Click on the link to find out more about this program.

More about FP_setup4.3.exe

RETURN TO TOP OF THE PAGE

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/INSTALL/install.htm (5 of 5)2006-03-10 1:33:39 PM

On Screen Display

On Screen Display Control • Using Your Remote Control

On Screen Display Controls

An overall view of the On-Screen Display (OSD) structure is shown below. You can use it as a reference for further adjusting your Monitor.

Main menu

Sub-menus

Picture: press to enter sub-menu selections.

Selection How to use

Smart Picture

In PC mode

● Users can press or to toggle between ❍ Normal ❍ Warm ❍ Cool

● Press to next sub-menu selection or to return

to main menu.

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/OSD/osddesc.htm (1 of 8)2006-03-10 1:33:40 PM

On Screen Display

Brightness

Adjust image brightness.

● Press or to adjust,

● Press or to adjacent sub menu selections,

● Press to return to main menu.

Contrast

Adjust image sharpness.

● Press or to adjust,

● Press to adjacent sub-menu selections,

● Press to return to main menu.

Auto Adjust

Automatic fine tuning display geometry and time frequency parameter.

● Press to start,

● A selection of Store? Yes/No will appear.

● Press or to toggle between Yes and No.

● Press to confirm and return to sub-menu.

Manual Adjust

Adjust display geometry and time frequency parameters.

● Phase: Press or to adjust, to confirm and

return to sub-menu.

● Clock: Phase: Press or to adjust, to confirm

and return to sub-menu.

● Horizontal: Phase: Press or to adjust, to

confirm and return to sub-menu.

● Vertical: Phase: Press or to adjust, to confirm

and return to sub-menu.

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/OSD/osddesc.htm (2 of 8)2006-03-10 1:33:40 PM

On Screen Display

Audio: press to enter sub-menu selections

Smart Sound

Preset audio modes.

● Users can press or to toggle between ❍ Personal ❍ News ❍ Music ❍ Theater

● Press to next sub-menu selections

● or to return to main menu.

Settings

Adjust audio setting parameters.

● Users can press or to toggle between ❍ Treble ❍ Bass ❍ Balance

● Press or to adjacent sub-menu selections

● or to return to main menu.

Virtual Surround Sound

Switch virtual surround effect on or off.

● Users can press or to toggle between ❍ On ❍ Off

● Press or to adjacent sub-menu selections, to

return to main menu.

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/OSD/osddesc.htm (3 of 8)2006-03-10 1:33:40 PM

On Screen Display

AVL

Auto Volume Limit, adjust volume level automatically to prevent sudden peak load exceeds design limit.

● Users can press or to toggle between ❍ Yes ❍ No

● Press or to adjacent sub-menu selections, to

return to main menu.

Features: press

to enter sub-menu

selections.

PIP

Picture in Picture size choices.

● Press to enter PIP sub-menu, and press or to

selection between

❍ Size ❍ Video ❍ Audio ❍ Display

● Press to return from PIP sub-menu to sub-menu, or

press

or to return to main menu.

PIP Sub-menu

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/OSD/osddesc.htm (4 of 8)2006-03-10 1:33:40 PM

On Screen Display

Size

PIP window size adjustment.

● Users can use or to toggle between ❍ Small ❍ Medium ❍ Large ❍ PBP ❍ Off

● Press or to return to upper level sub-menu, to

next selection.

Video

Video source of the PIP window.

● Users can use or to toggle between ❍ AV (CVBS) ❍ S-video ❍ EXT (Scart)

● Press or to adjacent sub-menu selections, to

return to upper level sub-menu.

Audio

Audio source of the PIP window.

● Users can use or to toggle between ❍ PC ❍ PIP

● Press or to adjacent sub-menu selections, to

return to upper level sub-menu.

Display

PIP window location selection.

● Users can use or to toggle between ❍ Icon1 (upper right corner of the screen) ❍ Icon2 (lower right corner of the screen) ❍ Icon3 (lower left corner of the screen) ❍ Icon4 (upper left corner of the screen)

● Press or to adjacent sub-menu selections, to

return to upper level sub-menu.

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/OSD/osddesc.htm (5 of 8)2006-03-10 1:33:40 PM

On Screen Display

Source

Choices of video source for main screen.

● Users can use or to toggle between ❍ PC ❍ DVI ❍ HDCP ❍ AV (CVBS) ❍ S-video ❍ EXT (Euro connector, Scart)

● Press or to adjacent sub-menu selections, to

return to upper level sub-menu.

Zoom

Choices for Zoom function.

● Users can use to enter next level sub-menu and Zoom sub-

menu.

Zoom sub-menu

Zoom Type

● Users can use or to toggle between ❍ Off ❍ 4x4 ❍ 3x3 ❍ 2x2 ❍ 1x5

● Press to confirm and to return to upper level sub-

menu.

Zoom ID

This selections is only available when one of zoom types is chosen. When zoom type is off, this selections is unavailable.

● Users can use or to toggle between IDs. For

example, when 4x4 is chosen, the ID selection are

A1 A2 A3 A3 B1 B2 B3 B4 C1 C2 C3 C4 D1 D2 D3 D4

● Press to confirm and to return to Zoom Type and

exit to upper level sub-menu.

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/OSD/osddesc.htm (6 of 8)2006-03-10 1:33:40 PM

On Screen Display

Install: press to enter sub-menu selections.

Language

Choices of languages in user interfaces.

● Users can use or to toggle between ❍ ENGLISH ❍ ESPAÑOL

❍

❍ DEUTSCH ❍ ITALIANO

❍

● Press to adjacent sub-menu selections or to

return to main menu.

Monitor ID

Assigning a three digits monitor ID to the unit, so it can be identified when using RS232 to control from remote.

● Use to enter, and or to select 1~9

numbers,

to confirm.

DCR

Dynamic Contrast Ratio, technology to boost display contrast ratio.

● Users can use or to toggle between ❍ On ❍ Off

● Press or to adjacent sub-menu selections.

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/OSD/osddesc.htm (7 of 8)2006-03-10 1:33:40 PM

On Screen Display

Light Sensor

Turns on or off the light sensor for automatic brightness control.

● Users can use or to toggle between ❍ On ❍ Off

● Press or to adjacent sub-menu selections.

Remote Control

Users need to turn off remote control function when they want to use RS232 protocol to control this unit from afar, so it will remote control commands not to conflict with RS232 commands.

● Users can use or to toggle between ❍ On ❍ Off

● Press or to adjacent sub-menu selections.

Factory Reset

To reset Monitor's settings back to factory default.

● Users can use or to toggle between ❍ No ❍ Yes

● Press to confirm.

RETURN TO TOP OF THE PAGE

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/OSD/osddesc.htm (8 of 8)2006-03-10 1:33:40 PM

Remote Control

On Screen Display • Using Your Remote Control

Using Your Remote Control

AV source:

● If Monitor is in Standby mode, press this button to switch to ON.

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/OSD/tv_control.htm (1 of 4)2006-03-10 1:33:41 PM

Remote Control

Mode:

Screen aspect ratio, switching between 4:3, 16: 9, wide screen, and super wide.

Numerical keys:

● For direct access to programs.

Previous program:

Jump to previous input source channel you are viewing.

Menu:

To turn on or off the On-screen-display (OSD) menu

● Move the cursor up in OSD

● Channel up

● Move the cursor left in OSD

● Adjust volume down

Switching between video input source and PC mode.

Closed Caption:

Functions in North America and Asia Pacific models only.

● Move the cursor down in OSD

● Channel down

● Move the cursor right in OSD

● Adjust volume up

Confirm the chosen OSD function

Freeze:

Freeze the screen in video mode or PIP.

Status:

Display channel number, video/PC mode, and sound mode information.

file:///D|/My%20Documents/dfu/BDL_27/english/420wn6/OSD/tv_control.htm (2 of 4)2006-03-10 1:33:41 PM

+ 89 hidden pages