Peugeot 4007 2010 Owner's Manual
INSTRUMENTS and CONTROLS
1
Panel grouping together the dials and
warning/indicator lamps. These inform
the driver of the activation/deactivation
of a system or of the occurrence of a
fault.
1. Rev counter.
2. Speedometer.
3. Instrument panel screen:
- Warning and status displays.
- Total and trip distance recorders.
- Service indicator.
- Coolant temperature.
- Trip computer information.
- Cruise control setting.
- Dashboard lighting and parameter
settings.
- Fuel level.
- Ambient temperature.
- Transmission mode.
Screen type 1
Screen type 2
INSTRUMENTS and CONTROLS
Warning lamp is on Cause Actions/ Observations
1
Left-hand
direction
indicator
Flashing
with
audible
warning
This fl ashes when you
press the lighting stalk
down.
If this indicator lamp fl ashes abnormally quickly,
this could indicate that the bulb of one of the
direction indicators has blown. Change the bulb
or contact a PEUGEOT dealer.
Right-hand
direction
indicator
Main beam
headlamps
Sidelamps Fixed
Front foglamps Fixed
Rear foglamps Fixed
Cruise control Fixed
Flashing
with
audible
warning
Fixed
This fl ashes when you
push the lighting stalk up.
This comes on when
you pull the lighting stalk
towards you.
This comes on when the
lighting stalk is in the
"Sidelamps" or "Dipped
beam headlamps"
position.
This comes on when you
use the front foglamps.
This comes on when you
use the rear foglamps.
This comes on when the
mode is active.
If this indicator lamp fl ashes abnormally quickly,
this could indicate that the bulb of one of the
direction indicators has blown. Change the bulb
or contact a PEUGEOT dealer.
Pull the stalk to return to dipped beam
headlamps.
Turn the stalk to the desired position.
Turn the ring on the stalk forwards to switch on
the foglamps.
Turn the ring on the stalk forwards to switch on
the foglamps.
Press the "ON/OFF" button to activate/deactivate
the mode.
INSTRUMENTS and CONTROLS
Warning lamp is on Cause Actions/Observations
Diesel
preheating
Fixed
This comes on when the
ignition switch is in the
ON position.
Wait until this goes off before starting.
The duration for which this is on is determined by
the exterior climatic conditions.
Parking brake/
Brake fl uid level
Fixed
This comes on for a
few seconds when the
ignition is turned to "ON"
then goes off.
It is accompanied by a message on the
instrument panel screen.
The parking brake is
applied or has not been
released fully.
It is accompanied by a message on the
instrument panel screen. Release the parking
brake to switch off the warning lamp.
The brake fl uid level is
too low.
It is accompanied by a message on the
instrument panel screen. Top up with brake fl uid
and contact a PEUGEOT dealer.
Emission
control system
Fixed or
fl ashing
This comes on or
fl ashes if the system
fails.
Consult a PEUGEOT dealer.
It should go off a few seconds after starting the
engine.
Battery charge Fixed
This comes on if a
charging circuit fault
occurs.
It should go off when the engine is started.
It is accompanied by a message on the
instrument panel screen. Check the battery
terminals (refer to the "Battery" section).
1
INSTRUMENTS and CONTROLS
Warning lamp is on Cause Actions/Observations
1
Driver's
seat belt not
fastened
Fixed
The driver has not
fastened or has
unfastened their seat
belt.
This is accompanied by a message on the
instrument panel screen.
Fasten the driver's seat belt.
ABS Fixed
Airbags and
pretensioners
Dynamic
stability control
system (ASC)
Fixed
Fixed
This comes on if an
anti-lock braking system
fault occurs.
This comes on for a
few seconds when the
ignition is turned to "ON"
then goes off.
This comes on if an
airbag or pretensioner
fault occurs.
This comes on if a
dynamic stability control
system fault occurs.
It is accompanied by a message on the
instrument panel screen. The vehicle retains
conventional braking without assistance but
you are advised to stop. Have it checked by a
PEUGEOT dealer.
It should go off when the engine is started. If it
does not go off, contact a PEUGEOT dealer.
It is accompanied by a message on the
instrument panel screen. Have the system
checked by a PEUGEOT dealer without delay.
It is accompanied by a message on the
instrument panel screen. Have the system
checked by a PEUGEOT dealer without delay.
INSTRUMENTS and CONTROLS
Each time the engine is started: a series of warning lamps and/or messages come on, applying a checking self test. They go
off after a few seconds. Engine running: the warning lamp or the message becomes a warning if it remains on continuously
or fl ashes. This initial warning may be accompanied by an audible signal and a message on the screen. Do not ignore these
warnings.
The messages displayed may differ between the type 1 instrument panel and the type 2 instrument panel.
When the cause of the appearance of the warning lamp or warning message has been rectifi ed, the warning disappears
from the screen automatically. If the cause of the warning is not rectifi ed, you can return to the previous screen at any time
by pressing the INFO button on the dashboard.
The symbol "!" is displayed.
To return to the previous screen (with the "!" symbol), you must press the INFO button several times.
Symbols which appear in the top right corner of the screen.
You can close the warning messages which show these symbols in order to move on to the next screen.
To do this, press the INFO button according to the symbol displayed.
Press briefl y . Press and hold .
Warning messages (ignition at "OFF")
Message is on Cause Solution - action Observations
1
Key in
ignition
Lighting left
on
Fixed
Fixed
The driver's door is open
and you have forgotten
to remove the key from
the ignition.
You have forgotten to
switch off the vehicle
lighting.
Turn the ignition switch
to the LOCK position
and remove the key.
Switch off the vehicle
lighting by placing the
stalk at OFF.
Only if the engine has
been started.
An intermittent audible
signal is heard.
An intermittent audible
signal is heard.
INSTRUMENTS and CONTROLS
Warning messages (ignition at "ON")
1
Message is on Cause Solution - action Observations
ABS Fixed
Seat belt Fixed
Braking
system
Parking brake
on
Coolant
temperature
Fixed
Fixed
Flashing
Flashing
Anti-lock braking system
(ABS) fault.
Associated warning
lamp.
The level of brake fl uid in
the reservoir is too low.
Associated warning
lamp.
Braking system fault.
You have moved off with
the parking brake still
applied.
High engine
temperature.
The driver has not fastened
or has unfastened his seat
belt.
Consult a PEUGEOT
dealer.
Stop and top up, otherwise
contact a PEUGEOT dealer.
Consult a PEUGEOT
dealer.
Release the parking brake.
If the message fl ashes ,
wait for the engine to cool
before topping up the level,
if necessary.
If the message fl ashes
and the service warning
light comes on , contact
a PEUGEOT dealer
without delay.
Fasten your seat belt.
The vehicle retains
conventional braking
without assistance but
you are advised to stop.
If the message remains
on after topping up,
contact a PEUGEOT
dealer.
You must stop.
You must stop your
vehicle as soon as it
is safe to do so .
There is an intermittent
audible signal above
5 mph (8 km/h).
!
INSTRUMENTS and CONTROLS
Message is on Cause Solution - action Observations
1
Airbags Fixed
Service Fixed
Engine oil
pressure
Engine oil
level
Low fuel
warning
Fuel system Fixed Fuel system fault.
Opening
not closed
correctly
Fixed
Fixed Engine oil level too low.
Fixed The fuel level is low.
Fixed
Fault in the airbags or
pretensioners.
Problem in one of the
systems which does not
have a specifi c message.
Engine oil pressure too
low or fault in the engine
lubrication system.
One of the doors or the
tailgate is not closed
correctly.
Consult a PEUGEOT
dealer.
Stop the vehicle and
contact a PEUGEOT
dealer.
Stop the vehicle and
contact a PEUGEOT
dealer.
Stop the vehicle and
check the level using the
dipstick.
Refuel as soon as
possible.
Consult a PEUGEOT
dealer.
Close the door or the
tailgate.
To identify the problem,
contact a PEUGEOT
dealer.
If there is a lack of oil,
top up the level.
The opening concerned
is indicated on the
screen.
INSTRUMENTS and CONTROLS
1
Message is on Cause Solution - action Observations
Dynamic
stability control
system (ASC)
Four wheel
drive system
Four wheel
drive system
temperature
Automatic
headlamp
adjustment
system
Battery charge Fixed Battery charge fault.
Ambient
temperature
Fixed
Fixed
Fixed
Fixed
Fixed
Dynamic stability control
system (ASC) fault.
Four wheel drive
transmission system
fault.
The temperature of the
four wheel drive
transmission system is
too high.
The automatic headlamp
adjustment is faulty.
The ambient
temperature is 3 °C
(37 °F) or below.
Consult a PEUGEOT
dealer.
Consult a PEUGEOT
dealer.
Stop the vehicle and
contact a PEUGEOT
dealer.
Consult a PEUGEOT
dealer.
Stop the vehicle and
contact a PEUGEOT
dealer.
Road icy.
Take care and drive
slowly.
The vehicle switches to
front wheel drive (2 WD)
mode automatically.
Only on vehicle fi tted
with xenon bulbs.
Caution: The road may
be icy even when this
screen is not displayed.
INSTRUMENTS and CONTROLS
Message is on Cause Solution - action Observations
Saturation of
the particle
emission fi lter
Fixed
Start of saturation of the
particle emission fi lter.
As soon as traffi c
conditions permit,
regenerate the fi lter by
driving at a speed of at
least 35 mph (60 km/h)
until the message is
cleared.
If the message is still
displayed, contact a
PEUGEOT dealer.
Diesel additive
level
Fixed
Low Diesel additive
level.
Have the level topped
up by a PEUGEOT
dealer without delay.
Water in the
Diesel fi lter
(according to
country)
Fixed
The presence of water
in the Diesel fi lter is
indicated.
Risk of damage to the
injection system on
Diesel engines.
Contact a PEUGEOT
dealer without delay.
1
INSTRUMENTS and CONTROLS
Information messages (ignition at "ON")
Message is on Status of the system
1
2WD two wheel
drive system
Flashing
When the "2WD" (2 wheel drive) mode is selected using
the transmission mode selector.
4WD four wheel
drive system
4WD LOCK four
wheel drive system
Ambient
temperature
Prevention messages
Display is on Cause Solution - action Observations
Service
indicator
Break
advised
Fixed
Fixed
When the "4WD" (4 wheel drive) mode is selected using
Flashing
Flashing
Fixed
Informs the driver of
the time remaining
before the vehicle's
scheduled service.
Informs the driver that
they should stop to
take a break.
the transmission mode selector.
This mode is the default mode.
When the "LOCK" (4 wheel drive) mode is selected using
the transmission mode selector.
This indicates the ambient temperature.
When the vehicle is stationary or if the speed is below 12 mph
(20 km/h) the temperature displayed may not be the true
temperature.
Consult a
PEUGEOT dealer.
You are advised to
take a break.
This is displayed for a
few seconds when the ignition
is switched on.
This is displayed when the
driving time that you set
previously is reached.
An audible signal is heard
3 times and is then heard
every 5 minutes until the
vehicle stops.
INSTRUMENTS and CONTROLS
Information display
With the ignition on, press the INFO
button, located on the dashboard to the
right of the instrument panel, to display
the various information in succession:
- distance recorder A,
- distance recorder B,
- service indicator,
- coolant temperature,
- range,
- trip computer,
- setting menu.
Distance recorder (A and B)
The total distance is
displayed in zone 1
of the screen and the
trip distance in zone 2
(refer to the "Distance
recorders" section).
Service indicator
This displays the distance
and the number of months
remaining before the
next service in line with
with the manufacturer's
servicing schedule (refer
to the "Service indicator"
section).
Coolant temperature
When the engine is
running, this indicates
the temperature of the
coolant (refer to the
"Coolant temperature
indicator" section).
Range
When the engine is
running, this indicates
the number of miles
(kilometres) which can
still be travelled with the
fuel remaining in the tank
based on the average
the last few miles (kilometres) travelled
(refer to the "Range" section).
Trip computer
Setting menu
- the fuel consumption units,
- the option to reset the average
fuel consumption and the average
speed,
- the break (rest) reminder display
interval.
fuel consumption over
This indicates the average
fuel consumption, the
average speed and the
current fuel consumption
(refer to the "Trip
computer" section).
When the vehicle is
stationary , this allows
the user to change the
following settings (refer
to the "Setting menu"
section):
- the display language,
- the temperature dis-
play units,
1
INSTRUMENTS and CONTROLS
System for measuring the total distance
travelled by the vehicle during its service
1
life and the distance travelled in a day
or other period until it is reset to zero by
the driver.
The total distance is
displayed in zone 1 of
the screen and the trip
distance in zone 2 .
Zero reset
With the ignition on, press the INFO
button for more than 2 seconds until
zeros appear.
When the engine is
running, this indicates
the temperature of the
coolant.
If the bar is close to the critical position
located on the right, the temperature is
too high.
The symbol fl ashes when your engine
is overheating.
You must stop your vehicle as soon
as it is safe to do so .
Wait a few minutes before switching
off the engine.
Wait for the engine to cool before
topping up the level. The cooling
system is pressurised.
To avoid any risk of scalding,
unscrew the cap by two turns to
allow the pressure to drop.
When the pressure has dropped,
remove the cap and top up the
level, if necessary.
Consult a PEUGEOT dealer.
When the engine is
running , this indicates
the distance which can
still be travelled with the
fuel remaining in the tank
based on the average
fuel consumption over
the last few miles/
kilometres travelled.
When the range is less than 30 miles
(50 km) , dashes are displayed.
Refuel as soon as possible. The display
of the range is updated.
This fi gure may increase
following a change in the style
of driving or the relief, resulting
in a reduction in the current fuel
consumption.
If you only add a few litres, the
value displayed will be incorrect.
Therefore, you must fi ll the tank
whenever possible.
When you disconnect the battery,
the previous fuel consumption
data is lost and the value
displayed will be different from
that displayed before the battery
was disconnected. The distance
displayed must be considered
an approximate indication.
INSTRUMENTS and CONTROLS
System which informs the driver when
the next service is due in accordance
with the manufacturer's servicing
schedule.
The point at which the next service is
due is calculated from the last service
indicator zero reset.
It is determined by two parameters:
- the distance travelled (in miles (km)),
- the time elapsed since the last service (in months).
The distance remaining to be travelled
may be weighted by the time factor,
depending on the user's driving habits.
Operation
When the ignition is switched on, you
must press the INFO button several
times in succession until the service
indicator is displayed. The distance
recorder display line indicates the
number of miles (kilometres) remaining
and the time elapsed line indicates the
number of months remaining before the
next service is due.
Example: the display indicates that
7 300 miles (kilometres) remain before
the next service is due.
The symbol "--" remains
displayed until the fi rst service of
a new vehicle has been carried
out.
Service overdue
Each time the ignition is switched on,
the display " PERIODIC INSPECTION "
is displayed for a few seconds to
indicate that the service must be carried
out without delay.
Example: the display indicates that the
service is overdue. This service must
be carried out by a PEUGEOT dealer.
Resetting the service indicator
to zero
Your PEUGEOT dealer carries out this
operation after each service.
If you have carried out your vehicle's
service yourself, the zero reset
procedure is the following:
switch off the ignition.
press the INFO button several times
in succession until the service indicator is displayed.
press and hold the INFO button for
a few seconds until the spanner
fl ashes .
press the INFO button while the
spanner is fl ashing to change the
display "---" to "CLEAR" then the
time remaining before the next service is due is displayed.
After a certain distance and a
certain time, the display of "---" is
reinitialised and the display indicates
the time remaining before the next
service is due.
1
INSTRUMENTS and CONTROLS
System for measuring the total distance
travelled by the vehicle during its service
1
life and the distance travelled in a day
or other period until it is reset to zero by
the driver.
The total distance is
displayed in zone 1 of
the screen and the trip
distance in zone 2 .
Zero reset
With the ignition on, press the INFO
button for more than 2 seconds until
zeros appear.
When the engine is
running, this indicates
the temperature of the
coolant.
If the bar is close to the critical position
located on the right, the temperature is
too high.
The symbol fl ashes when your engine
is overheating.
You must stop your vehicle as soon
as it is safe to do so .
Wait a few minutes before switching
off the engine.
Wait for the engine to cool before
topping up the level. The cooling
system is pressurised.
To avoid any risk of scalding,
unscrew the cap by two turns to
allow the pressure to drop.
When the pressure has dropped,
remove the cap and top up the
level, if necessary.
Consult a PEUGEOT dealer.
When the engine is
running , this indicates
the distance which can
still be travelled with the
fuel remaining in the tank
based on the average
fuel consumption over
the last few miles/
kilometres travelled.
When the range is less than 30 miles
(50 km) , dashes are displayed.
Refuel as soon as possible. The display
of the range is updated.
This fi gure may increase
following a change in the style
of driving or the relief, resulting
in a reduction in the current fuel
consumption.
If you only add a few litres, the
value displayed will be incorrect.
Therefore, you must fi ll the tank
whenever possible.
When you disconnect the battery,
the previous fuel consumption
data is lost and the value
displayed will be different from
that displayed before the battery
was disconnected. The distance
displayed must be considered
an approximate indication.
INSTRUMENTS and CONTROLS
System which informs the driver when
the next service is due in accordance
with the manufacturer's servicing
schedule.
The point at which the next service is
due is calculated from the last service
indicator zero reset.
It is determined by two parameters:
- the distance travelled (in miles (km)),
- the time elapsed since the last service (in months).
The distance remaining to be travelled
may be weighted by the time factor,
depending on the user's driving habits.
Operation
When the ignition is switched on, you
must press the INFO button several
times in succession until the service
indicator is displayed. The distance
recorder display line indicates the
number of miles (kilometres) remaining
and the time elapsed line indicates the
number of months remaining before the
next service is due.
Example: the display indicates that
7 300 miles (kilometres) remain before
the next service is due.
The symbol "--" remains
displayed until the fi rst service of
a new vehicle has been carried
out.
Service overdue
Each time the ignition is switched on,
the display " PERIODIC INSPECTION "
is displayed for a few seconds to
indicate that the service must be carried
out without delay.
Example: the display indicates that the
service is overdue. This service must
be carried out by a PEUGEOT dealer.
Resetting the service indicator
to zero
Your PEUGEOT dealer carries out this
operation after each service.
If you have carried out your vehicle's
service yourself, the zero reset
procedure is the following:
switch off the ignition.
press the INFO button several times
in succession until the service indicator is displayed.
press and hold the INFO button for
a few seconds until the spanner
fl ashes .
press the INFO button while the
spanner is fl ashing to change the
display "---" to "CLEAR" then the
time remaining before the next service is due is displayed.
After a certain distance and a
certain time, the display of "---" is
reinitialised and the display indicates
the time remaining before the next
service is due.
1
INSTRUMENTS and CONTROLS
Information display
1
With the ignition on, press the INFO
button on the dashboard, to the right
of the instrument panel, several times
in succession to display the different
information:
- average fuel consumption,
- average speed,
- current fuel consumption.
If dashes "---" are displayed
for long periods in place of the
digits while driving, contact a
PEUGEOT dealer.
Average fuel
consumption (l/100 km
or km/l or mpg)
This is the average fuel
consumption since the
last zero reset.
This fi gure may change following
a change in the style of driving or
the relief resulting in a change in
the current fuel consumption.
Average speed
(km/h or mph)
This is the average
speed calculated since
the last zero reset.
Current fuel
consumption
(l/100 km or km/l or
mpg)
This is the average fuel
consumption during
the last few seconds of
driving.
Resetting the information to zero
When the required information is
displayed, press the INFO button for
more than two seconds to reset all of
the information to zero.
When the ignition is switched on, the
zero reset switches automatically from
manual mode to automatic mode.
Automatic
If the ignition key remains in the
OFF position for more than 4 hours,
the information is reset to zero
automatically.
INSTRUMENTS and CONTROLS
SETTING MENU
SETTING MENU
System which provides access to the
settings of certain functions.
The various menus may differ for the
type 1 instrument panel and the type 2
instrument panel.
With the ignition on , press the INFO
button on the dashboard, to the right of
the instrument panel, several times in
succession until the "SETTING MENU"
screen is displayed.
When the vehicle is
stationary , it allows
the user to change the
following settings:
- resetting average fuel
consumption and av-
erage speed,
- the fuel consumption units,
- the temperature display units,
- the display language,
- activation/deactivation of the INFO
button sound,
- the break (rest) reminder display in-
terval,
- restore factory settings.
To change the settings, you
must stop the vehicle and switch
on the ignition.
Apply the parking brake and
place the gear lever in neutral.
When the vehicle is moving ,
the setting menu screen is not
displayed when you press the
INFO button.
Operation
press and hold the INFO button for
a few seconds to display the menu
screen.
on the menu screen, press the INFO
button to select a function from the
list:
MENU 1/3 :
- 1 - 2 (options for resetting aver-
age fuel consumption and average
speed),
- UNIT (choice of the fuel consumption
units),
- choice of the temperature display
unit s ,
- LANGUAGE (choice of display lan-
guage),
MENU 2/3:
- a/b (option of displaying a different
language in the instrument panel
screen and the navigation screen),
- activation/deactivation of the
INFO button sound ,
- ALARM (changing the "BREAK
REMINDER" display interval),
- choice of the direction indicators
sound,
- activation/deactivation of current
fuel consumption,
MENU 3/3:
- RESET (restore factory settings).
Press and hold the INFO button
for a few seconds to return to
the previous screen.
When the menus screen is
displayed, if no operation is
carried out within 15 seconds,
the setting menu screen is
displayed.
1
INSTRUMENTS and CONTROLS
Options for resetting average
fuel consumption and average
speed
1
You can choose between two average
fuel consumption and average speed
resetting modes:
- automatic reset ( choice 1) ,
- manual reset (choice 2) .
On the menu screen:
press the INFO button to select:
press and hold the INFO button for a
few seconds to switch in succession
from resetting mode 1 (automatic)
to resetting mode 2 (manual) .
The mode selected is confi rmed.
Choice of fuel consumption
units
You can choose between different units
for displaying fuel consumption.
In this case, the distance, speed and
quantity of fuel units will also be changed
in accordance with your choice of fuel
consumption unit.
On the menu screen:
press the INFO button to select
"UNIT" .
press and hold the INFO button for
a few seconds to display the "UNIT"
screen.
press the INFO button to scroll the units
(km/L, L/100 km, mpg(US), mpg(UK)
and RETURN) in succession.
press and hold the INFO button
for a few seconds to confi rm your
selection.
If the battery is disconnected,
the settings memory is cleared
and the default unit (km/L) is
restored automatically.
Choice of temperature display
units
You can choose between different units
for displaying the temperature.
On the menu screen:
press the INFO button to se-
lect the temperature unit setting symbol (thermometer).
press and hold the INFO button for
a few seconds to alternate between
the units (°C and °F).
The mode selected is confi rmed.
If the battery is disconnected, the
settings memory is cleared and
the default unit (°C) is restored
automatically.
INSTRUMENTS and CONTROLS
Choice of display language
(LANGUAGE)
You can choose between different
languages for the screen.
On the menus screen:
press the INFO button to select
"LANGUAGE" .
press and hold the INFO button
for a few seconds to display the
"LANGUAGE" screen.
press the INFO button to scroll
through the languages (Japonais,
English, Deutsch, Français, Espanol,
Italiano, "---" and RETURN) in
succession.
press and hold the INFO button for
a few seconds to confi rm your se-
lection.
If you select the "---" setting, no
message will be displayed in
message display situations.
If the battery is disconnected, the
settings memory is cleared and
the default language (ENGLISH)
is restored automatically.
Activation/deactivation of the
"INFO" button sound
You can activate or deactivate the INFO
button sound.
On the menus screen:
press the INFO button to se-
lect the INFO button sound
activation/deactivation symbol (located on menu 2/3) .
press and hold the INFO button for
a few seconds to alternate between
the choices (ON, OFF).
The mode selected is confi rmed.
If the battery is disconnected,
the settings memory is cleared
and the default choice (ON) is
restored automatically.
Changing the display interval
of the "BREAK REMINDER"
message
You can change the display interval of
the "BREAK REMINDER" message.
On the menu screen:
press the INFO button to select
" ALARM " (located on menu 2/3) .
press and hold the INFO button
for a few seconds to display the
" ALARM " screen.
press the INFO button to select
the display interval of the "BREAK
REMINDER" message.
press and hold the INFO button for
a few seconds to confi rm.
If the battery is disconnected,
the settings memory is cleared
and the default value (OFF) is
restored automatically.
1
INSTRUMENTS and CONTROLS
Choice of the direction
indicators sound
You can choose the sound of the
1
direction indicators, on the type 2
instrument panel only.
On the menus screen:
press the INFO button to select sound 1
or 2 (located on menu 2/3) .
Activation/deactivation of the
current fuel consumption
You can activate or deactivate the
current fuel consumption, on the type 2
instrument panel only.
On the menu screen:
press the INFO button to select the
current fuel consumption activation/
deactivation symbol (located on
menu 2/3) .
press the INFO button for a few
seconds to alternate between the
choices (ON, OFF).
Restoring factory settings
(RESET)
You can restore all of the factory settings
for all of the functions.
On the menu screen:
press the INFO button to select
" RESET " (located on menu 2/2 or
3/3 depending on the instrument
panel) .
press and hold the INFO button for
at least 5 seconds .
An audible signal is heard and all of the
factory settings are restored for all of
the functions.
The factory settings are:
Functions Factory setting
Resetting average
fuel consumption
and average
speed
Fuel consumption
units
Temperature
display unit
Display language ENGLISH
INFO button
sound
Display of
the "BREAK
REMINDER"
message
1 (automatic)
L/100 km
°C
ON (activated)
OFF (deactivated)
INSTRUMENTS and CONTROLS
This provides the following information:
- the time,
- audio system information (refer to
the "Audio and Telematics" section).
Setting the time
The digital clock can be set in automatic mode or in manual mode .
Automatic mode
This mode permits automatic setting
of the local time using the signal from
RDS stations.
The symbol "CT" appears on the
screen.
Manual mode
This mode permits manual setting of
the time using the audio equipment
buttons.
It can also be used when the "Automatic
mode" displays an inaccurate time, when
the local RDS stations are broadcasting
from a different time zone.
Selecting the Setting
Select the automatic mode or the
manual mode as follows:
1
Press button A "PWR" to switch on
the audio system.
Access the setting mode by pressing
button B "TUNE" for approximately
2 seconds.
Press button B "TUNE" several
times to scroll through the various
menus and select the CT menu
(clock time).
The order of the menus is the
following: AF/CT/REG/TP-S/PTY
display language/SCV/PHONE/
Functions setting mode OFF.
INSTRUMENTS and CONTROLS
1
Turn button B "TUNE" to the left or
to the right to select "CT ON" (auto-
matic mode) or "CT OFF" (manual
mode).
After selecting the mode, you can
exit the "Functions setting mode"
menu by pressing button B "TUNE"
for approximately 2 seconds.
If no action is carried out within
10 seconds, the system will exit
the "Functions setting mode"
menu automatically.
Automatic mode
In this mode, setting is automatic using
the signal from the RDS radio stations.
Manual mode
Set the time using the buttons as
indicated below:
with the ignition on or in the ACC
(Accessories) position, press and
hold the CLOCK button until the
time display fl ashes.
Press the appropriate button to set
the time:
Button H: to set the hours
The hours digits scroll when you press
this button.
Button M: to set the minutes
The minutes digits scroll when you
press this button.
Button 00: to reset the minutes to
zero.
- from 1 to 29 min : rounded down to
the previous hour,
- from 30 to 59 min: rounded up to
the next hour.
After setting the time, press the
DISP button; the time display stops
fl ashing.
The digital clock does not display
seconds.
When the "minutes" display is
set or reset to zero, the clock
starts at the zero second of the
minute selected.
The time setting is lost if the
battery is disconnected.
INSTRUMENTS and CONTROLS
This permits display of the following
main menus:
"Audio-video" menu
On the control panel, press button A
(MODE) to access the "AV mode"
screen and select:
- radio (FM, MW, LW),
- CD (audio, MP3 or WMA),
- Music Server,
- DVD.
The "CD" and "DVD" buttons
are active if you insert a CD or
DVD in the player.
"Settings" menu
On the control panel, press button B
(SET) to access the "Settings" screen
and select:
- "Display Off " to switch off the dis-
play,
- "Sound control" for the sound dis-
tribution or volume, the type of music and the sound fi eld (surround),
- "Picture control" to set the colour,
the intensity, the brightness, the
contrast and the level of black,
- "System" to change the time zone,
the language, the units and other
settings,
- "Wide Screen" to change the size
of the DVD picture to 4/3 format,
wide screen mode, centred wide
screen mode or enlargement,
- "Equipment" to set certain equip-
ment offered in the vehicle,
- " Colour Contrast" to select the
contrast of the display in relation
to the ambient light (Day, Night or
Auto),
- "TP standby" to activate or deacti-
vate the traffi c information.
"Navigation-guidance" menu
On the control panel, press button C
(MENU) to access the "Menu" screen
and select:
- "Address/Junction" to search for
a location using the address or the
name of the street,
- "POI name" to search for a location
using the name of a point of interest
(POI),
- "Advanced search" to search for a
location using an advanced search
based on a POI,
- " Previous 20 " to search for a loca-
tion using one of the 20 previous
destinations,
- "Address book" to search for a loca-
tion using a stored address,
- " Go home " to navigate to your
home address,
- "Navigation settings" to set func-
tions linked with the navigation,
-
"Navigation tools" to access the basic
information or a pre-set demonstration.
1
INSTRUMENTS and CONTROLS
"Info" menu
1
On the control panel, press button D
(INFO) to access the "Info" screen and
consult:
- "Support info" to display the soft-
ware and data versions,
- "Vehicle position" to display the
GPS location of the vehicle,
- "Calendar" to make a note of
events, birthdays, etc.,
- "Journey" to display the average
speed, fuel consumption, distances
and driving time,
- "Environment" to display the alti-
tude, the atmospheric pressure, the
exterior temperature (the ice symbol
is displayed if there is a risk of ice),
- "Air conditioning" to display the
information relating to the air condi-
tioning,
- "Mobile phone " to enter a number,
delete a character, make or receive
a call.
"Route" menu
On the control panel, press button E
(NAVI) to access the "Route Menu"
screen and select:
- "Detour" to make a detour through
a specifi ed region,
- " Itinerary " to change the route,
- " View route" to display a route in
different ways,
- "Delete route" to delete a route,
- " Nearby POI" to search for the
POIs in the surrounding area.
Setting the time
The digital clock is set automatically .
This mode enables the system to set
the local time automatically using the
signal from the RDS stations.
On the control panel, press button
B (SET) to access the "Settings"
menu.
On the touch screen, press button B
to access the "System" menu.
The system settings screen is
displayed.
INSTRUMENTS and CONTROLS
Once this menu has been selected, you
can access the following functions:
System for manual adjustment of the
brightness of the instruments and
controls in relation to the exterior
brightness.
1
Press button C to access the "Time"
menu .
1. RDS Auto Correct :
Activate/deactivate automatic ad-
justment.
2. GMT/GMT+1/GMT+2
Select the time zone.
3. Summer Time:
Summer time On/Off.
Press button D to confi rm and re-
turn to the previous menu.
You must deactivate automatic
adjustment (RDS Auto Correct)
to change the time zone and
summer time settings.
On each screen, you can return
to the previous screen by
pressing button D "Return" .
With the lighting on or off, press the
button to change the intensity of the
lighting of the instruments and controls
in "day" or "night" mode.
An audible signal is heard and
the intensity of the lighting
increases each time the button
is pressed.
When the lighting reaches the maximum
setting, press again to change to the
minimum setting.
When the lighting reaches the required
intensity, release the button.
The setting is saved when the ignition
switch is turned to OFF.
INSTRUMENTS and CONTROLS
"Info" menu
1
On the control panel, press button D
(INFO) to access the "Info" screen and
consult:
- "Support info" to display the soft-
ware and data versions,
- "Vehicle position" to display the
GPS location of the vehicle,
- "Calendar" to make a note of
events, birthdays, etc.,
- "Journey" to display the average
speed, fuel consumption, distances
and driving time,
- "Environment" to display the alti-
tude, the atmospheric pressure, the
exterior temperature (the ice symbol
is displayed if there is a risk of ice),
- "Air conditioning" to display the
information relating to the air condi-
tioning,
- "Mobile phone " to enter a number,
delete a character, make or receive
a call.
"Route" menu
On the control panel, press button E
(NAVI) to access the "Route Menu"
screen and select:
- "Detour" to make a detour through
a specifi ed region,
- " Itinerary " to change the route,
- " View route" to display a route in
different ways,
- "Delete route" to delete a route,
- " Nearby POI" to search for the
POIs in the surrounding area.
Setting the time
The digital clock is set automatically .
This mode enables the system to set
the local time automatically using the
signal from the RDS stations.
On the control panel, press button
B (SET) to access the "Settings"
menu.
On the touch screen, press button B
to access the "System" menu.
The system settings screen is
displayed.
INSTRUMENTS and CONTROLS
Once this menu has been selected, you
can access the following functions:
System for manual adjustment of the
brightness of the instruments and
controls in relation to the exterior
brightness.
1
Press button C to access the "Time"
menu .
1. RDS Auto Correct :
Activate/deactivate automatic ad-
justment.
2. GMT/GMT+1/GMT+2
Select the time zone.
3. Summer Time:
Summer time On/Off.
Press button D to confi rm and re-
turn to the previous menu.
You must deactivate automatic
adjustment (RDS Auto Correct)
to change the time zone and
summer time settings.
On each screen, you can return
to the previous screen by
pressing button D "Return" .
With the lighting on or off, press the
button to change the intensity of the
lighting of the instruments and controls
in "day" or "night" mode.
An audible signal is heard and
the intensity of the lighting
increases each time the button
is pressed.
When the lighting reaches the maximum
setting, press again to change to the
minimum setting.
When the lighting reaches the required
intensity, release the button.
The setting is saved when the ignition
switch is turned to OFF.
INSTRUMENTS and CONTROLS
Once this menu has been selected, you
can access the following functions:
System for manual adjustment of the
brightness of the instruments and
controls in relation to the exterior
brightness.
1
Press button C to access the "Time"
menu .
1. RDS Auto Correct :
Activate/deactivate automatic ad-
justment.
2. GMT/GMT+1/GMT+2
Select the time zone.
3. Summer Time:
Summer time On/Off.
Press button D to confi rm and re-
turn to the previous menu.
You must deactivate automatic
adjustment (RDS Auto Correct)
to change the time zone and
summer time settings.
On each screen, you can return
to the previous screen by
pressing button D "Return" .
With the lighting on or off, press the
button to change the intensity of the
lighting of the instruments and controls
in "day" or "night" mode.
An audible signal is heard and
the intensity of the lighting
increases each time the button
is pressed.
When the lighting reaches the maximum
setting, press again to change to the
minimum setting.
When the lighting reaches the required
intensity, release the button.
The setting is saved when the ignition
switch is turned to OFF.
COMFORT
AUTOMATIC REGULATION OF
Use of the automatic regulation of the
air conditioning is recommended. It permits automatic and optimised control of
all of the following functions: air fl ow,
2
passenger compartment temperature
and air distribution, by means of various
sensors (ambient temperature, interior
temperature, sunshine), so preventing
the need for you to change your set-
tings other than the value displayed.
Do not cover the temperature and humidity
sensor 2 and the sunshine sensor 7 .
They are required for regulation of the
air conditioning.
Advice on operation
In hot weather, in order to obtain
intense ventilation, it is advisable to use vents 1 and 4 only.
If, when the vehicle has been
parked in the sun for a long time,
the interior temperature remains
very high, fi rst ventilate the passenger compartment for a few
minutes.
For even air distribution, take care not
to obstruct the exterior air intake grille
located at the bottom of the windscreen,
the vents, the air outlets under the front
seats and the air extractor located be-
hind the fl aps in the boot.
In certain cases of particularly arduous
use (towing the maximum load on a
steep gradient in hot weather), switch-
ing off the air conditioning saves engine
power and therefore improves the towing capacity.
Close the windows to benefi t from the
full effectiveness of the air conditioning.
Ensure that the passenger compartment fi lter is in good condition. Have
the fi lter elements replaced periodically.
If you drive in a dusty environment, re-
place it twice as often.
The air conditioning system does not
contain chlorine and is not harmful to
the ozone layer.
Operate the air conditioning system for
5 to 10 minutes, once or twice a month,
to keep it in good working order.
The water formed by the air conditioning
condensation is discharged via an opening provided for this purpose. Therefore,
a puddle of water may form underneath
the vehicle when stationary.
If the system does not produce cold air,
do not use it and have it checked by a
PEUGEOT dealer.
1. Central vents.
2. Temperature sensor.
3. Air outlet to passenger footwells.
4. Side vents.
5. Front window demisting/defrosting
vents.
6. Windscreen demisting/defrosting
vents.
7. Sunshine sensor.
Switch off the air conditioning
when the climatic conditions
permit.
COMFORT
2
Loading...