Pentax RTH6580, RTH6580WF, RTH6585, TRH6585WF User's Guide

User Guide

Wi-Fi Programmable Thermostat

RTH6500WF Wi-Fi Series

In the box you will find

• Thermostat

• Wallplate (attached to thermostat)

• Screws and anchors

• Quick Start Guide

• Thermostat ID Card

• Wire labels

• User Guide

• Quick Reference Card

69-2718ES—03 ii

Welcome

Congratulations on your purchase of a Honeywell Wi-Fi programmable thermostat. When registered to Honeywell’s Total Connect Comfort Solutions, you can remotely monitor and control the heating and cooling system in your home or business—you can stay connected to your comfort system wherever you go.

Honeywell’s Total Connect Comfort is the perfect solution if you travel frequently, own a vacation home, a business or manage an Investment property or if you are simply looking for peace of mind.

This thermostat works with common 24 volt systems such as forced air, hydronic, heat pump, oil, gas, and electric. It will not work with millivolt systems, such as a gas fireplace, or with 120/240 volt systems such as baseboard electric heat.

MERCURY NOTICE: Do not place your old thermostat in the trash if it contains mercury in a sealed tube. Contact the Thermostat Recycling Corporation at www. thermostat-recycle.org or 1-800-238-8192 for information on how and where to properly and safely dispose of your old thermostat.

NOTICE: To avoid possible compressor damage, do not run air conditioner if the outside temperature drops below 50°F (10°C).

Need help?

Visit wifithermostat.com or call 1-855-733-5465 for assistance before returning the thermostat to the store.

69-2718ES—03 2

Table of contents

About your new thermostat

Controls and Home screen

quick reference ............................................5

Preset energy-saving schedules ................. 6

Installation

Installing your thermostat ............................ 8

Connecting to your Wi-Fi network .............26

Registering your thermostat online ........... 31

Operation

Setting the clock ........................................ 36

Setting the fan ........................................... 37

Selecting system mode ............................. 38

Adjusting program schedules .................... 39

Overriding schedules temporarily .............40

Overriding schedules permanently ........... 41

69-2718ES—03 3

Unregistering thermostat........................... 42

Disconnecting Wi-Fi .................................. 43

Special features ........................................45

Setting functions and options ....................48

Appendices

Frequently asked questions ......................55

Troubleshooting .........................................61

Limited warranty ........................................ 67

Features of your Wi-Fi thermostat

With your new thermostat, you can:

• Connect to the Internet to monitor and control your heating/cooling system

• View and change your heating/cooling system settings

• View and set temperature and schedules

• Receive alerts via email and get automatic upgrades

Your new thermostat provides:

• Smart Response Technology

• Compressor protection

• Heat/cool auto changeover

69-2718ES—03 4

Controls and home screen quick reference

M31586

Once your Wi-Fi thermostat is installed, it will display the home screen. Portions of this display will change depending on how you are viewing it.

Set up messages describe steps in the Wi-Fi set up process

Set clock, day,

or schedule

Select fan

settings

HOLD

Select system

mode

Wi-Fi status

Temperature adjustment buttons

Permanent override button

Additional settings

The screen lights when you press any button. It stays lit for 8 seconds after you complete changes.

5 69-2718ES—03

Preset energy-saving schedules

This thermostat is pre-set with energy-saving program settings for four time periods. Using the default settings can reduce your heating/cooling expenses if used as directed. Savings may vary depending on geographic region and usage. To change the settings, see pages 39–41.

Default Heat Settings Default Cool Settings

WAKE

6:00 am

LEAVE

8:00 am

RETURN

6:00 pm

SLEEP

10:00 pm

69-2718ES—03 6

Setting up your thermostat

Setting up your Wi-Fi programmable thermostat is easy. It is preprogrammed and ready to go as soon as it is installed and registered.

Install your thermostat.

Connect your home Wi-Fi network.

Before you begin, you may want to watch a brief installation video. Use

the QR Code® at the front of this guide, or go to wifithermostat.com/support

7 69-2718ES—03

Installing your thermostat

You might need the following tools to install this thermostat:

• No. 2 Phillips screwdriver

• Small pocket screwdriver

• Pencil

• Level (optional)

1 Switch OFF power to your

heating/cooling system.

Important! To protect your equipment,

switch OFF the power to your heating/ cooling system at the breaker box or the system switch.

69-2718ES—03 8

• Drill and bits (3/16” for drywall, 7/32” for plaster) (optional)

• Hammer (optional)

• Electrical tape (optional)

Circuit breaker

box

Heating/cooling

system power

switch

Installing your thermostat

2 Remove old thermostat faceplate

and leave wires connected. 2a Take a picture of the wire

If you have an older thermostat with a sealed mercury tube, turn to page 2 for proper disposal instructions.

connections for later reference.

2b If no wire is connected to a

terminal labeled C or no C terminal exists on the old thermostat, view the Alternate Wiring videos at

wifithermostat.com/videos

Important! C wire is required and

is the primary power source for your thermostat. Without a C wire, your thermostat will not power up.

9 69-2718ES—03

Terminal designation

Installing your thermostat

3 Label wires.

Do not label by wire color. Use

the supplied sticky tags to label each wire as you disconnect it. Label wires according to the old thermostat terminal designations, not by wire color.

Note: If no tag matches a wire

terminal label, write the terminal label on a blank tag.

4 Remove wallplate.

Remove the old wallplate from the wall after all wires have been labeled and disconnected.

69-2718ES—03 10

Sticky tags

Blank sticky tags

Terminal designation

Installing your thermostat

5 Separate Wi-Fi thermostat and its

wallplate.

On your new thermostat, grasp the

Thermostat

Finger holds

finger holds on the top and bottom of the wallplate with one hand and the thermostat (front) with the other hand.

PULL HERE TO REMOVE

Pull pieces apart.

PULL HERE TO REMOVE

M33856

Wallplate (back view)

11 69-2718ES—03

Installing your thermostat

MCR33857

6 Mount wallplate for Wi-Fi thermostat.

Mount your new wallplate using screws and anchors included with the thermostat.

If necessary: Drill 3/16-in holes for drywall. Drill 7/32-in holes for plaster.

Note: You may be able to use your existing

wall anchors. Hold the wallplate up to the existing anchors to check for alignment.

Wallplate

69-2718ES—03 12

Installing your thermostat

Important! The Wi-Fi thermostat requires a C wire to operate. The C, or common, wire

brings 24 VAC power to the thermostat. Many older mechanical or battery operated thermostats do not require a C wire. If you don’t have a C wire, try:

• Looking for an unused wire that is pushed into the wall. Connect that wire to C and check that it is connected to the 24 VAC common at your heating/cooling system.

Note: Not all heating/cooling systems label the 24 VAC common C. Check your system

manual or contact the manufacturer to find out which terminal is the 24 VAC common.

View the Alternate Wiring videos at wifithermostat.com/videos

Wiring

For conventional heating/cooling systems (natural gas, oil or electric furnace, air conditioner), see page 14. See “Glossary” on page 64 for further definition.

For a heat pump system, see page 15. See “Glossary” on page 64 for further definition.

13 69-2718ES—03

Installing your thermostat

Wiring (conventional system)

7A Wire the Wi-Fi thermostat to your conventional system.

a Starting with the C Wire, match the sticky tag on the

wire to the terminal labels.

You must have a C wire. See page 13.

b Loosen screw, insert wire on inside edge

of terminal, then tighten screw.

c Verify wire is firmly secured by gently

pulling on wire. d Repeat steps a–c for all other wires. e Push any excess wire back into the wall

opening after all wires are installed. f Continue to page 20.

Labels don’t match? See alternate

wiring key on pages 16–17.

69-2718ES—03 14

Remove metal jumper

only if you have both

R and RC wires

G W

AUX/E

G O/B

YR RCK

CONVENTIONAL

YRRCK

HEAT PUMP

Note: The wiring for your

application might be different from the wiring shown above.

Installing your thermostat

Wiring (heat pump system only)

7B Wire Wi-Fi thermostat to your heat pump.

Labels don’t match? See alternate

wiring key on pages 18–19.

a Starting with the C Wire, match the sticky tag on the wire to the terminal labels.

You must have a C wire. See page 13.

b Loosen screw, insert wire on inside edge

of terminal, then tighten screw. c Verify wire is firmly secured by gently

pulling on wire.

Aux

d Repeat steps a–c for all other wires. e Push any excess wire back into the wall

opening after all wires are installed.

Continue to page 20.

AUX/E

G O/B

YRRCK

HEAT PUMP

Note: If old thermostat has separate wires on AUX and

E, place both wires into the E/AUX terminal.

If old thermostat has wire on AUX with a jumper to E, place wire on E/AUX terminal. No jumper is required.

15 69-2718ES—03

Note: The wiring for your

application might be different from the wiring shown above.

Installing your thermostat

MCR33885

CONVENTIONAL

Alternate wiring (conventional system)

Use this if your wire labels don’t match the terminal labels.

Note: You must have

a C wire or equivalent. See page 13.

G W

69-2718ES—03 16

W1F

X B C1

YRRC

RYWG

RHY1

4M V

See key to 1 – 3

on page 17.

Installing your thermostat

Alternate wiring key (conventional system)

Do not use K terminal. For future use.

If your old thermostat had both R and RH wires, remove metal jumper.

Connect the R wire to the RC terminal, and the RH wire to the R terminal. Remove metal jumper connecting R and RC only if you must connect both

R and RC.

17 69-2718ES—03

Installing your thermostat

MCR33886

T PUMP

Alternate wiring (heat pump system only)

Use this if your wire labels don’t match the terminal labels.

Note: You must have

a C wire or equivalent. See page 13.

EAUX

XW FH

W1 W2

X B

VY1

VRM

AUX/E

G O/B

69-2718ES—03 18

YRRCK

HEA

See key to 1 – 7

on page 19.

Installing your thermostat

Alternate wiring key (heat pump system only)

Do not use K terminal. For future use.

If old thermostat has separate wires on AUX and E, place both wires into the E /AUX terminal. If

old thermostat has wire on AUX with a jumper to E, place wire on E /AUX terminal. No jumper is required.

If your old thermostat had an O wire and not a B wire, attach the O wire to the O/B terminal.

If your old thermostat had separate O and B wires, attach the B wire to the C terminal. If

another wire is attached to the C terminal, check wifithermostat.com for help. Attach the O wire to the O/B terminal.

If your old thermostat had separate Y1, W1 and W2 wires, check wifithermostat.com for help.

If your old thermostat had both V and VR wires, check wifithermostat.com for help.

Leave metal jumper between R and RC terminals in place.

19 69-2718ES—03

Installing your thermostat

8 Insert quick reference card.

Fold quick reference card along score lines, and slide it into the slot on the back of the thermostat.

69-2718ES—03 20

Quick reference card

MCR33916

Back of thermostat

Installing your thermostat

M33860

9 Attach thermostat to wallplate.

Align the thermostat to the wallplate and then snap into place.

HOLD

21 69-2718ES—03

Installing your thermostat

10 Switch heating/cooling system ON.

Important!

10a Verify that the C wire is

connected at the thermostat and at the heating/cooling system.

10b Make sure the heating/

cooling system door is firmly secured.

10c Switch power back ON for

your heating/cooling system at the breaker box or its power switch.

69-2718ES—03 22

Circuit breaker

box

Heating/cooling

system power

switch

Installing your thermostat

MCR33909

11 Set clock to current day and time.

11a Press s or t to set clock. 11b Press Set Day. 11c Press s or t to select the

day of week.

11d Press Done to save.

(Press and hold a st button to quickly change a setting.)

HOLD

MCR33908

HOLD

23 69-2718ES—03

Installing your thermostat

12 Determine your heating/cooling system type.

Important! Heating/cooling system type must be set so that your

thermostat operates properly and does not damage your system.

12a If your system type is conventional single stage (natural gas-powered single

stage with a/c), continue to “Connecting to your Wi-Fi network” on page 26.

12b If your system is:

• Conventional multistage heat and cool

• Any type of heat pump

• Hydronic

• Other

You MUST change the system type by setting system function 1. See page 48 to match your thermostat to your system type.

69-2718ES—03 24

If you are not sure of your heating/cooling system type or have other questions, go to wifithermostat.com/support

Installing your thermostat

MCR33880

Congratulations! Your thermostat is operational. 13 Test your thermostat

13a Press the

heating or cooling and begin operation.

13b For remote access to your thermostat,

continue to

network” on page 26.

25 69-2718ES—03

System

button to change to

“Connecting to your Wi-Fi

Heating/cooling system not turning on? Refer to page 62 or FAQ at wifithermostat.com/support

Connecting to your Wi-Fi network

To complete this process, you must have a wireless device connected to your home wireless network. Any of these device types will work:

• Tablet (recommended)

• Laptop (recommended)

• Smartphone

If you get stuck... at any point in this procedure, restart the thermostat by

removing the thermostat from the wallplate, wait for 10 seconds, and snap it back onto the wallplate. Go to Step 1 in this procedure, starting on page 27.

View the Wi-Fi Enrollment video at wifithermostat.com/videos

69-2718ES—03 26

Connecting to your Wi-Fi network

M33852

1 Connect to your thermostat.

1a Make sure the thermostat displays

Wi-Fi Setup.

1b On the wireless device (laptop, tablet,

smartphone), view the list of available Wi-Fi networks.

1c Connect to the network called

NewThermostat_123456 (the number will vary).

Note: If you are asked to specify a home, public, or

office network, select Home Network.

27 69-2718ES—03

HOLD

Connecting to your Wi-Fi network

M31567

2 Join your home network.

2a Open your web browser to access the

Thermostat Wi-Fi Setup page. The browser should automatically direct you to the correct page; if it does not, go to http://192.168.1.1

2b Find the name of your home network on this

page and select it.

Note: Some routers have enhanced features such as

guest networks; use your home network.

2c Complete the instructions for joining your Wi-Fi

network and click on the Connect button. (Depending on your network setup, you may see an instruction such as Enter Password for your home network.)

Note: If you did not correctly connect to the thermostat, you may see

your home router page. If so, return to Step 1.

69-2718ES—03 28

+ 110 hidden pages