Pelco TW3001AR User Manual

INSTALLATION

TW3001AR Active Receiver

Single Channel for UTP Transmission

C1666M-A (4/06)

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁt into your outlet consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14. Apparatus shall not be exposed to dripping or splashing and that no objects ﬁlled with liquids, such as vases shall be placed on the apparatus.

WARNING:

15. moisture.

16. Installation should be done only by qualiﬁed personnel and conform to all local codes.

17. Unless the unit is speciﬁcally marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.

18. Use only installation methods and materials capable of supporting four times the maximum speciﬁed load.

19. A CCC-approved power cord must be used to power this equipment when used in China.

To reduce the risk of ﬁre or electric shock, do not expose this apparatus to rain or

C1666M-A (4/06) 3

Regulatory Notices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Changes and Modiﬁcations not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules.

In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and television reception.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

4 C1666M-A (4/06)

Description

The TW3001AR is a single-channel active receiver that can receive live video over unshielded twisted pair (UTP) cable.

The adaptive technology in the TW3001AR automatically adjusts the low, medium and high frequency components of the video signal allowing for the best possible video transmission. The adaptive technology eliminates the need for manual adjustment by automatically adjusting to provide the most favorable video transmission depending on cable length needed. The unit has been optimized for use with Cat5e and Cat6 cable, although Cat3 and Cat5 cable can be used for shorter distances.

The DIP switch on the bottom of the TW3001AR allows you to override the adaptive technology and manually select the cable distance. Switches 1, 2, 3, and 4 can be set to 4,000 feet (1,219 meters), 3,000 feet (914 meters), 2,000 feet (610 meters), and 1,000 feet (305 meters), respectively. Switch 5 can be set to high mode and low mode.

There are two ways you can power the TW3001AR. You can power it by installing it into an RK5000PS-3U using the 4-pin connector. For stand-alone power, you can use the 2-pin power connector and use either a 12 VDC power supply (supplied) or a 24 VAC power supply.

The following features are found on the TW3001AR:

•

Full motion color/black and white video up to 4,000 feet (1,219 meters) with Cat5e or Cat6

•

Supports Coaxitron control (PTZ control signals) up to 750 feet (229 meters)

•

Compatible with all Pelco twisted pair equipped cameras, enclosures, and domes

•

Built-in surge suppression

•

Easy termination with removable UTP connector

•

Supports NTSC, PAL, and SECAM

•

Can be mounted into a Pelco ﬁber rack, wall mount base kit, or wall clip

C1666M-A (4/06) 5

PARTS OF THE RECEIVER

MODEL

FREQ



 











Figure 1.

Rubber Feet (4):

 

Status LED:

For placing unit on a ﬂat surface, such as a desk or shelf.

Lights red when there is no UTP video being received. Lights green when there is UTP video being received. Flashes amber when Coaxitron pan/tilt/zoom (PTZ) control commands are being received.

Pelco Badge:



Lights blue to indicate power when using either the 4-pin rack power connector

or the 2-pin power connector.

TW3001AR Parts

OPERATION

THISDEVICE

(1)

AND

INCLUSING

THISDEVICE MA

(2)THIS DEVICE

INTERFERENCE

ISSUBJECT

COMPLIES

YNOTCAUSE

MUST

WITH

TOTHE

THA

PART 15 OFTHE

FOLLOWINGT

HARMFUL

AY CAUS EUNDESIRED

ANY

INTERFERENCE

INTERFERENCE,

FCCRULES.

CONDITIONS:

RECEIVED,

OPERA

TION.

Rack Power Connector:

 

Power Connector (3.5 mm):

UTP Connector (2.5 mm):



BNC Connector:

 

DIP Switch:

Override the adaptive technology with the manual selection of cable distance

4-pin, power from RK5000PS-3U.

2-pin; stand-alone power, 12 VDC or 24 VAC.

2-pin connector with removable mating connector.

Coaxial output.

(1,000-4,000 feet or 305-1,219 meters). Switch 5 is used for selecting high mode or low mode.

6 C1666M-A (4/06)

+ 14 hidden pages