Pelco TLR2024 User Manual
®
TLR2024
Time-Lapse VCR
Installation/
Operation Manual
C650M (12/98)
Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.com
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120
CONTENTS
Section Page
1.0 GENERAL ..................................................................................................5
1.1 SAFEGUARDS, WARNINGS, CAUTION, AND CARE ..................... 6
1.2 REGULATORY NOTICES ................................................................. 8
1.3 UNPACKING INSTRUCTIONS ......................................................... 8
2.0 OVERVIEW ................................................................................................9
2.1 INTRODUCTION TO TIME-LAPSE RECORDERS .......................... 9
2.2 TLR2024 FEATURES AND FUNCTIONS.........................................9
3.0 QUICK START ..........................................................................................11
3.1 BASIC START...................................................................................11
3.2 ADDITIONAL ITEMS ....................................................................... 11
4.0 INSTALLATION ......................................................................................... 12
4.1 PRE-INSTALLATION CAUTIONS ....................................................12
4.1.1 Securing the VCR Controls ..................................................12
4.1.2 Monitor Tips ......................................................................... 12
4.2 INSTALLATION .............................................................................12
4.3 CONNECTING THE VCR TO A MULTIPLEXER ............................. 14
5.0 CONTROLS ..............................................................................................15
5.1 FRONT PANEL ................................................................................. 15
5.2 FLUORESCENT DISPLAY ...............................................................16
5.3 REAR PANEL.................................................................................... 17
6.0 PROGRAMMING ...................................................................................... 18
6.1 GENERAL PROGRAMMING INSTRUCTIONS ...............................18
6.2 QUICK GUIDE TO TLR2024 MENU STRUCTURE ......................... 19
6.3 MAIN MENU ..................................................................................... 20
6.4 DISPLAY MENU ...............................................................................20
6.4.1 Display Mode .......................................................................20
6.4.2 Time Date Size ....................................................................20
6.5 TIMER PROGRAM MENU ...............................................................21
6.6 RECORDING SET UP MENU .........................................................21
6.7 REAR TERMINAL MENU ................................................................22
6.8 MAINTENANCE MENU ................................................................... 23
6.9 FIRST TIME SET UP MENU ...........................................................23
6.9.1 Day and Time Display Modes .............................................. 24
6.9.2 Set the Day and Time .......................................................... 25
7.0 LOADING/UNLOADING/PROTECTING THE TAPE CASSETTE .............27
7.1 LOADING .......................................................................................... 27
7.2 UNLOADING .....................................................................................27
7.3 PREVENTING ACCIDENTAL ERASURE ........................................27
8.0 RECORDING ............................................................................................28
8.1 MANUAL RECORDING ...................................................................28
8.1.1 Recording Mode .................................................................. 28
8.1.2 Record Check Function ....................................................... 29
8.1.3 Audio Recording .................................................................. 29
8.1.4 Repeat Recording................................................................29
8.1.4.1 Number of Tape Uses (Repeat Recording Times) ..29
8.1.4.2 Recommended Number of Tape Uses ................ 30
8.1.5 Series Recording .................................................................30
8.2 TIMER RECORDING ....................................................................... 31
8.2.1 Programming Procedure......................................................31
8.2.2 Special DW Settings ............................................................31
8.2.3 Avoid Mistakes When Using the Timer ................................32
2 Pelco Manual C650M (12/98)
8.3 ALARM RECORDING ..................................................................... 32
8.3.1 Alarm Recording Connection ...............................................33
8.3.2 External Time Clock Adjustment ..........................................33
8.3.3 Programming for Alarm Recording ...................................... 34
8.3.4 Emergency Recording .........................................................35
8.3.5 Alarm Record Time Display .................................................35
8.4 RECORDING AFTER A POWER FAILURE.....................................35
9.0 PLAYBACK ...............................................................................................36
9.1 PLAYBACK PROCEDURE ..............................................................36
9.2 SPECIAL EFFECTS PLAYBACK .....................................................37
9.3 LOCATING THE START OF ALARM RECORDINGS......................39
9.4 ADJUSTMENT DURING PLAYBACK..............................................40
10.0 ADDITIONAL FUNCTIONS AND FEATURES .......................................... 42
10.1 COUNTER .......................................................................................42
10.2 MEMORY BACKUP IN CASE OF POWER FAILURE .....................42
10.3 POWER FAILURE TIME DISPLAY ..................................................42
10.4 ELAPSED TIME DISPLAY...............................................................43
8.3.5.1 Reset the Alarm Recording List ...........................35
9.1.1 Playback Mode ....................................................................36
9.1.2 Audio Playback ....................................................................37
9.1.3 End of Tape ..........................................................................37
9.2.1 Shuttle Ring .........................................................................38
9.2.2 Direct Shuttle Ring ...............................................................38
9.2.3 Still Picture...........................................................................39
9.2.4 Frame-by-Frame Playback ..................................................39
9.3.1 Index Search ....................................................................... 39
9.3.2 Skip Search ......................................................................... 40
9.4.1 Tracking Adjustment ............................................................ 40
9.4.2 Picture Quality Adjustment ...................................................41
9.4.3 Vertical Adjustment .............................................................. 41
10.1.1 Counter Memory ..................................................................42
10.1.2 Tape Counter ....................................................................... 42
10.1.3 Counter Reset ..................................................................... 42
11.0 TESTING ..................................................................................................43
11.1 INITIAL SYSTEM TESTING ............................................................ 43
11.2 REGULAR SYSTEM TESTING ....................................................... 43
12.0 TROUBLESHOOTING ..............................................................................44
12.1 SELF-DIAGNOSTIC FUNCTION AND WARNING DISPLAY .......... 44
12.2 BEFORE CALLING FOR SERVICE ................................................45
13.0 SPECIFICATIONS ....................................................................................46
14.0 WARRANTY AND RETURN INFORMATION ...........................................48
Pelco Manual C650M (12/98) 3
LIST OF ILLUSTRATIONS
Figure Page
1 Typical System Setup .......................................................................13
2 Connecting VCR to Multiplexer .........................................................14
3 Front View .........................................................................................15
4 Fluorescent Display .......................................................................... 16
5 Rear View ......................................................................................... 17
6 Menu Tree.........................................................................................19
7 Main Menu ........................................................................................20
8 Display Menu ....................................................................................20
9 Timer Program Illustration.................................................................21
10 Recording Set Up Menu ................................................................... 21
11 Rear Terminal Menu ..........................................................................22
12 Maintenance Menu ........................................................................... 23
13 First Time Set Up Menu ....................................................................23
14 Display Mode 1 .................................................................................24
15 Display Mode 2 .................................................................................24
16 Manual Recording Steps .................................................................. 28
17 Connecting VCRs in Series .............................................................. 30
18 Switching from Normal to Alarm Mode and Back ............................. 32
19 Alarm Recording Connection ............................................................33
20 Time Clock Adjustment Connection ..................................................33
21 Playback Controls .............................................................................36
22 Shuttle Ring Speed Settings .............................................................38
23 Direct Shuttle Ring Speed Settings .................................................. 38
24 Index Searching ................................................................................39
25 Skip Searching ..................................................................................40
26 Tracking Adjustment .........................................................................40
27 Picture Quality Adjustment................................................................41
28 Vertical Picture Adjustment ............................................................... 41
LIST OF TABLES
Table Page
A Call Out/Tape End .............................................................................22
B Recording Times in Hours ................................................................ 28
C When Tape End is Reached .............................................................29
D Recommended Number Of Tape Uses .............................................30
E Timer Recording Troubleshooting ..................................................... 32
F Audio Playback Availability................................................................38
G End of Tape Actions ..........................................................................38
H Warning Display and Actions ............................................................ 44
REVISION HISTORY
Manual # Date Comments
C650M 12/98 Original version.
4 Pelco Manual C650M (12/98)
1.0 GENERAL
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
the user to the presence of uninsulated
dangerous voltage within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the equipment.
A VERTISSEMENT
DANGER D’ÉLECTROCUTION
NE PAS OUVRIR
AVERTISSEMENT: POUR ÉLIMINER TOUT RISQUE
D’ÉLECTROCUTION, NE PAS OUVRIR LE
COUVERCLE (OU LA PARTIE ARRIÈRE).
AUCUNE PIECE RÉPARABLE PAR
L’UTILISATEUR NE SE TROUVE À
L’INTÉRIEUR. POUR TOUTE
INTERVENTION D’ENTRETIEN OU DE
RÉPARATION SE CONFIER AUX
TECHNICIENS QUALIFIÉS.
La flèche symbolisant l’éclair dans un triangle
équilateral a pour objet de tirer l’attention de
l’utilisateur sur le fait, qu’il y a des tensions
dangereuses non-isolées à l’intérieur de
l’enceinte du produit qui peuvent être
suffisamment impor-tantes pour conduire au
risque d’électrocution.
Le point d’exclamation au sein d’un triangle
équilateral a pour objet de tirer l’attention de
l’utilisateur sur le fait qu’il y a des instructions
de mise en service et d’entretien (de
réparation) dans les fiches descriptives de
l’appareil qui doivent obligatoirement être
respectées.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK DO NOT USE
THE POLARIZED PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET
UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE.
A VERTISSEMENT:
AFIN D’ÉVITER TOUT RISQUE D’INCENDIE
OU D’ÉLECTROCUTION, NE PAS EXPOSER
CET APPAREIL À LA PLUIE NI À L’HUMIDITÉ.
ATTENTION:
POUR PRÉVENIR LES CHOCS
ÉLECTRIQUES NE PAS UTILISER CETTE
FICHE POLARISÉE AVEC UN
PROLONGATEUR, UNE PRISE DE COURANT
OU UNE AUTRE SORTIE DE COURANT, SAUF
SI LES LAMES PEUVENT ÊTRE INSÉRÉES
À FOND SANS EN LAISSER AUCUNE PARTIE
À DÉCOUVERT.
Pelco Manual C650M (12/98) 5
1.1 SAFEGUARDS, WARNINGS, CAUTION, AND CARE
Observe the following WARNINGS before installing and using this product. Follow
all warnings and instructions marked on the VCR.
Instructions
Read all the safety and operating instructions before operating the VCR. Keep the
instructions for future reference. Follow all operating and use instructions. Heed all
warnings on the equipment and in the operating instructions.
Installation/Servicing
Installation and servicing should be done by qualified service personnel only and
conform to all local codes. Do not try to service this VCR yourself. Opening or removing covers may expose you to dangerous voltage or other hazards.
Damage Requiring Service
Unplug the VCR from the wall outlet and refer servicing to qualified service personnel under the following conditions:
1. When the power cord or plug is damaged.
2. If liquid has been spilled, or objects have fallen into the VCR.
3. If the VCR does not operate normally when following the operating instructions.
Adjust only those controls covered by the operating instructions. Improper adjustment of other controls may cause damage and will often require extensive
work by a qualified technician to restore the VCR to normal operation.
4. If the VCR was dropped or the cabinet damaged.
5. When the VCR shows a distinct change in performance–this indicates a need
for service.
Replacement Parts
Be sure the service technician uses only replacement parts Pelco recommends, or
which have the same characteristics as the original part. Unauthorized substitutions may cause fire, electric shock, or other hazards.
Safety Check
Upon completion of any service or repair to the VCR, ask the service technician to
perform safety checks to determine whether it is in safe operating condition.
Water/Moisture/Condensation
Do not use this VCR near water. It is designed for indoor use only and must not be
installed where exposed to rain and moisture.
Do not place objects containing water, such as drinks, on top of the VCR.
If the VCR is exposed to a rapid increase in temperature (such as warming a cold
room or after moving it from a cold location to a warm one), condensation may form
on the tape transport mechanism inside the VCR. To prevent damage to the VCR or
tapes, plug the VCR into the AC outlet and turn the power on for about two hours.
Do not play back or record on the VCR during this time.
Condensation is likely to occur when:
1. The VCR is moved from a cold room to a warm room or from outdoors to
indoors.
2. A cold room is heated quickly.
3. The humidity is very high.
Avoid using the VCR where cold air (such as from an air conditioner) will blow
directly on it.
6 Pelco Manual C650M (12/98)
Cleaning
Unplug the VCR from the wall outlet before cleaning. Do not use liquid or aerosol
cleaners. Clean with a soft cloth slightly moistened with mild detergent and water.
Wipe dry. NEVER USE PETROLEUM-BASED SOLUTIONS.
Attachments
Do not use attachments not recommended by Pelco as they may cause hazards.
Accessories
Do not place the VCR on an unstable cart, stand, tripod, bracket, or table. The VCR
may fall, seriously injuring a person or damaging the equipment. Use only with a
cart, stand, tripod, bracket, or table recommended by Pelco, or sold with the VCR.
Follow Pelco’s instructions when mounting equipment, and use a mounting accessory recommended by Pelco.
Use care when moving equipment on a cart. Quick stops, excessive force, and
uneven surfaces may overturn the VCR and cart combination.
Do Not Place Anything Heavy On The VCR
Heavy objects placed on the VCR will cause damage.
Ventilation
Slots and openings in the cabinet provide ventilation and ensure reliable operation
of the VCR and protect it from overheating. Do not block or cover these openings.
Never place the VCR near or over a radiator or heat register. Do not place it in a
built-in installation such as a rack unless proper ventilation is provided or Pelco’s
instructions have been followed. There are many ventilation holes on the bottom of
the VCR–for maximum ventilation, place it on a hard level surface only.
Power Sources
Operate this VCR only from the type of power source indicated on the marking
label. If you are unsure of the type of power supply, consult your equipment dealer
or local power company.
WARNING:
The included power cord is used
for 120 VAC, 60 Hz. Never
connect to any outlet or
power supply having a different voltage or frequency.
Grounding or Polarization
This VCR is equipped with a three-wire grounding-type plug–a plug having a third
(grounding) pin. This plug only fits into a grounding-type outlet. This is a safety
feature. If you cannot insert the plug into the outlet, contact an electrician to replace
the obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
Power Cord Protection
Do not damage the power cord; it may cause fire or shock hazard. Route the power
cord so it is not likely to be walked on or pinched by items placed on or against it.
Pay particular attention to the cord at the wall plug or convenience receptacle and
the point where it connects to the VCR. When unplugging the power cord, grasp the
plug and remove it carefully.
Lightning/Power Surges
Unplug the VCR from the wall outlet for its added protection during a lightning storm
or when it is unused for long periods. This prevents damage to the VCR from lightning and power line surges. Pelco recommends using conditioned-output
uninterruptible power supplies (UPS) and/or surge protected outlets to maximize
protection of the VCR.
When Not in Use
When you finish operating the VCR, always unload the cassette and turn off the
power.
Overloading
Do not overload wall outlets and extension cords as this increases the risk of fire
and electric shock.
Object and Liquid Entry
Never push objects of any kind into the VCR through openings. They may touch
dangerous voltage points or short out parts that could result in a fire or electric
shock. It can also cause extensive damage to the mechanism. Never spill liquid of
any kind on the VCR.
Pelco Manual C650M (12/98) 7
Care of Video Cassette Tape
1. Avoid violent vibration and shock.
2. Do not place near a strong magnetic field (near a motor, transformer, or magnet).
3. Never place or store in direct sunlight.
4. Avoid dusty places.
5. Place the cassette in the cassette case and store vertically.
6. Never store tapes in a high humidity location.
1.2 REGULATORY NOTICES
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
INFORMA TION
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
INFORMA TION
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement
sur le matériel brouilleur du Canada.
1.3 UNPACKING INSTRUCTIONS
Unpack and inspect all parts carefully.
Be sure to save the shipping carton, boxes and inserts. They are the safest material
in which to make future shipments.
If an item appears to have been damaged in shipment, replace it properly in its box
and contact the factory at 1-800-289-9100 or 1-559-292-1981 for a replacement.
(International customers fax 1-559-348-1120 for authorization and instructions.)
If an item needs to be returned to the factory for repair, consult the WARRANTY
AND RETURN section of this manual for instructions.
8 Pelco Manual C650M (12/98)
2.0 OVERVIEW
2.1 INTRODUCTION TO TIME-LAPSE RECORDERS
Time-lapse recording permits longer than ordinary recording times. The primary
reason for using time-lapse recording in a CCTV security system is that a single
VCR tape can be used for an extended period of time beyond the standard recording time. The following explains how time-lapse recording works.
The actual recording on VCRs is a series of still pictures or fields. Standard consumer VHS recorders store 60 fields (30 frames) per second. A T-120 cassette lasts
just two hours in this mode (SP mode). You can get slightly longer recording times
(six hours) using the extended recording mode (EP mode). You can record even
longer on a T-160 cassette in these modes: two hours and 40 minutes in SP mode
and eight hours in EP mode. (Refer to the table in Section 8.1.1 for actual recording
times in different modes.)
Time-lapse VCRs, however, use microprocessor-based techniques to record fewer
fields per second than a normal VHS machine and extend recording time. This negates the need to change the tape every two hours–and also substantially reduces
viewing time when the recording is played back, another important consideration.
In normal VCR operation, all video head scans (60 per second) are recorded. But in
time-lapse mode the tape runs more slowly and records pictures periodically. In 12hour mode, a normal time-lapse machine records 10 fields per second, and in 24hour mode, it stores just five fields per second (for up to 12 and 24 hours on a tape,
respectively). Longer times are possible by slowing the recording rate further.
At normal speed a picture is recorded every 1/60 of a second so there is little change
over five frames. In longer time-lapse modes, however, a field is recorded intermittently over a longer period of time so changes are apparent from field to field.
The time-lapse recording can be played back at normal two-hour tape speed, which
makes for rapid review–one of the time-lapse recorder’s most important advantages. Action on the tape, however, appears faster than normal.
As an advanced feature, time-lapse recorders (like the TLR2024) can automatically
switch from time-lapse to real-time recording when an alarm condition occurs. This
is important since the primary purpose of recording an event is identification, and
real-time recording provides more detail.
2.2 TLR2024 FEATURES AND FUNCTIONS
The TLR2024 time-lapse VCR is a powerful surveillance tool designed for industrial
and security recording. In addition to ordinary two-hour and six-hour recording modes,
it has time-lapse modes that allow recording in 12- and 24-hour modes. The TLR2024
features frame-by-frame playback and high-speed playback of longer recordings.
Audio Recording–Audio recorded in 2H, 6H, L(inear)12H, or L24H modes is played
back only in its respective mode.
Resolution And Image Quality–This VCR has a high-quality circuit allowing more
than 330 lines in B/W (black and white) mode, and more than 240 lines in color
mode.
Automatic Head Cleaning–The VCR automatically removes foreign matter from
the heads when a cassette is inserted for continuous smooth operation.
Easy Setup Using A Monitor– The on-screen menus simplify setup programming.
You can select these menus even without inputting a video signal.
Easy Cueing With Alarm Recording–Index signals are automatically added at
the beginning of alarm recording for easy cueing. You can even use the monitor to
confirm the starting time of alarm recording.
Pelco Manual C650M (12/98) 9
External Time Clock Adjustment–You can reset the on-screen clock to the nearest hour by applying a signal to the RST (reset) IN terminal at the rear of the VCR.
Record Check–You can confirm correct recording by pressing the PLAY button
during recording.
Special Playback Features–These include still images, speed search, reverse
playback, frame-by-frame viewing in both directions, slow-motion, and high-speed
viewing.
JOG Dial/SHUTTLE Ring–You can use these controls to search for the desired
image. You can adjust the playback speed with the SHUTTLE ring and search for an
image frame-by-frame with the JOG dial.
Recording Options–This versatile system offers a variety of recording options,
including daily and weekly timer recording, repeat, and alarm recording.
NOTE:
The battery backup is for
memory only–the VCR does not
continue recording if the power
goes out. If you want to keep recording during an outage, make
sure the VCR system is on your
UPS (uninterruptible power supply)
system.
Protection Against Power Failures–Recording data (including date, time, and
timer setup) is stored in backup memory, so the system can resume recording after
a power failure. The monitor displays the time of the failure.
Digital <ELAPSED TIME> Display–The elapsed time of recording and playback is
stored in non-volatile memory. You can use the elapsed time display as a guide to
when to do periodic maintenance.
Tape Use Counter–This counter displays how many times you have recorded on a
tape. This helps you decide when you need to replace a tape.
Daylight Saving Time Setting–A daylight saving time setting is available. You can
set the clock forward an hour by programming the menu.
10 Pelco Manual C650M (12/98)
3.1 BASIC START
3.0 QUICK START
NOTE:
This section is intended
for people experienced in working
with time-lapse recorders and installing CCTV systems. (However,
you might want to take a few minutes to review the material in Section 1.0.)
1. Decide where to locate the VCR. Do all system hookups first (camera, multiplexer, etc.) if you are installing the VCR in a location where you cannot access its rear panel.
2. Connect the VCR to other equipment (Sections 4.2 and 4.3).
3. Plug in the VCR and press the POWER button. You should see the time and
date displayed on the monitor.
4. To reset the time/date (First Time Set Up menu), see Section 6.9.2. Skip if you
do not want to reset the time/date.
5. Put in a T-120 or T-160 tape, refer to Table B for recording times.
6. Put the VCR in the recording mode you want by pressing the REC/PLAY (+)
and (-) buttons. Watch the fluorescent display. Set the recording speed to 2H,
6H, L12H, or L24H.
7. Press REC to begin recording.
8. Press STOP to stop. Turn the SHUTTLE ring right to fast forward and left to
rewind. Press PLAY to play back the tape.
9. Refer to Section 11.1 for initial system testing information.
3.2 ADDITIONAL ITEMS
You can also incorporate the following programming steps for more than a basic
quick setup.
1. If desired, set the tape end and quasi v-sync options (Section 6.9) on the First
Time Set Up menu.
2. If desired, set the display mode and time/date size options (Section 6.4) in the
Display menu.
3. If desired, program for timer recording in the Timer Program menu (Section
6.5).
4. If desired, in the Recording Set Up menu (Section 6.6), program for alarm
recording mode and duration (Section 8.3.3) and emergency recording (Section 8.3.4).
5. If desired, in the Rear Terminal menu (Section 6.7), program for call out (Section 8.1.5 for series recording), clock out, operation of the mode out terminal,
and operation mode of the REC IN terminal.
Pelco Manual C650M (12/98) 11
4.0 INSTALLATION
4.1 PRE-INSTALLATION CAUTIONS
1. Provide secure power to system components. Prevent overloading or shorting
by dedicating power circuits to the surveillance equipment. Restrict access to
the surveillance system circuit breakers, switches, and equipment power cords.
2. Surveillance system components must be operationally compatible. Time-lapse
recording speeds and dwell times of any accessory switching equipment must
be compatible with each other.
3. The TLR2024 time-lapse VCR provides multiple alarm recording speeds so it
is important that alarm triggering of components be operationally compatible.
Refer to Section 2.1 for information on time-lapse recording.
4. Complete all system hookups (camera, multiplexer, etc.) before installing the
VCR in a location where you cannot access its rear panel.
4.1.1 Securing the VCR Controls
Protect surveillance equipment to forestall tampering. We recommend putting the
recorder in a secure VCR cabinet. Pelco offers such units–the RM2000, which is a
rack kit for a single VCR, and the RM2004, which is a rack kit for four VCRs.
4.1.2 Monitor Tips
• Pelco recommends using a CCTV monitor.
• Some monitors may cause picture vibration or picture distortion at the top or
bottom of the image during still or normal playback. (Refer to Section 9.4.3 for
information.)
A television may be unable to provide a stable picture without vibration or distortion.
4.2 INSTALLATION
1. Remove the VCR and all cables from the box.
2. Place the VCR in a suitable location.
• If the location is unsecured, refer to Section 4.1.1 for information about
products to lock up the VCR.
• Do all system hookups (camera, multiplexer, etc.) before installing the
VCR in a location where you cannot access its rear panel.
3. If installing in a rack, place the VCR in the rack before making cable and power
connections. Refer to the documentation included with the rack kit for specific
installation instructions.
4. If you are not using a switcher, refer to Figure 1.
• Connect the camera (video output) to the rear of the VCR (video input
BNC). Connect the VCR (video output BNC) to the monitor (video input).
• Connect the alarm input to the VCR (SET IN and GND [ground] termi-
nals).
• If you are using a 600 Ω microphone, connect it to the VCR (MIC IN jack).
Connect the VCR (audio output connector) to the monitor (audio input).
5. If you are using a switcher, refer to Section 4.3.
12 Pelco Manual C650M (12/98)
CCTV
CAMERA
ALARM DEVICE
VIDEO OUTPUT
FROM CAMERA
ALARM OUTPUT
FROM DEVICE
MIC
600 Ω
SET
MIC IN
IN
SET RSTINREC GND ALM MODE CLK CALL
IN
OUTMIC
AUDIO
AUDIO
OUT
VIDEO
IN
OUT
OUTIN
VIDEO
RESET
REMOTE
VIDEO
OUT
VIDEO IN
AUDIO IN
AUDIO IN
MONITOR
Figure 1. Typical System Setup
Pelco Manual C650M (12/98) 13
4.3 CONNECTING THE VCR TO A MULTIPLEXER
Figure 2 shows how to connect the VCR to an MX4000 Series Genex™ Multiplexer.
• For Automatic Speed Tracking (“B” lines in Figure 2)
This lets the VCR control the multiplexer’s recording speed. It is the most efficient recording method.
1. Connect the VCR’s CLK output to the multiplexer’s head switching (HS)
input to synchronize camera switching.
2. Connect the multiplexer’s ground terminal to the VCR’s GND terminal.
NOTE:
Cameras and monitors are
connected to the multiplexer. Figure 2 shows the connection between the VCR and an MX4000
Series Genex™ Multiplexer. Refer
to the multiplexer manual for additional component connections.
• For Alarm Recording (“A” lines in Figure 2)
This is to start and stop recording when there are alarms.
1. Connect the multiplexer’s normally open (NO) relay terminal to the VCR’s
SET IN (alarm input) terminal.
2. Connect the common C terminal to the VCR’s GND terminal.
CALL
ALMINRECSET RST
GND
MODE
CLK
OUT
RESET
IN OUT
MIC
AUDIO
IN
REMOTE
OUT
VIDEO
TIME-LAPSE VCR
B
COAXIAL CABLE
COAXIAL CABLE
SPOT
MAIN
AUX
SVHS
VCR
OUT IN
SVHS
A
IN COM OUT
ALARMS
1 2 3 4 5 67 8 91011 14151612 13
NN
OCCS
H
120 VAC 60 Hz
MX4000 GENEX™ SERIES MULTIPLEXER
Figure 2. Connecting VCR to Multiplexer
14 Pelco Manual C650M (12/98)
5.1 FRONT PANEL
5.0 CONTROLS
12
POWER
EJECT
VIDEO
PICTURE
B/W
COLOR
I
POSITION/
SHARP
SOFT
VERTICAL
TRACKING
ADJUST
FGH
1. POWER button
Press for on; press again for off. The POWER indicator
illuminates when the VCR is turned on.
2. EJECT button
Press to remove the cassette.
3. Cassette loading slot
Insert the cassette in this slot to load it.
4. STOP button
Press to halt all tape-related functions.
5. REC (record) button
Press to begin recording.
6. JOG dial
Use to advance the tape frame-by-frame and to program
the menus.
7. SHUTTLE ring
Use to adjust the playback speed and to program the
menus. Turn this ring to the right to advance the tape or to
forward search. Turn it to the left to rewind a tape or to
reverse search. You can also use it to clear the alarm list,
power loss list, timer recording, and to initialize the menu
programming. It also lets you program or exit the menus
after setup.
8. PLAY button
Press to play back a previously recorded tape.
9. P AUSE/SHUTTLE HOLD button
Press this button during recording to temporarily stop tape
movement. Press again to resume recording. When it is
pressed during playback, tape movement stops and a still
field is displayed. Press again to restore normal playback.
Pressing and holding this button after turning the SHUTTLE
ring allows continuous high-speed playback even if the
SHUTTLE ring is released.
10. COUNTER MEMORY/SKIP/INDEX button
Press this button to switch among counter memory (fluorescent display shows M), skip search (displays SKIP), and
index search (displays INDEX).
3
Fluorescent display
Counter Memory: Turn the SHUTTLE ring to the right and
the tape rewinds to the 00000 counter position and stops
(Section 10.1.1).
Skip Search: The VCR fast forwards or rewinds until it locates an index signal and then plays back for about four
seconds in 2H or 6H mode, doing this until it reaches the
end or beginning of the tape (Section 9.3.2).
Index Search: During fast forward or rewind, the VCR
searches for alarm signals. When it finds one, the VCR plays
back the tape and stays in still mode (Section 9.3.1).
11. TIMER REC button
Press to make a timed recording.
12. REC/PLAY MODE buttons
Set to 2H, 6H, L12H, or L24H mode for recording; and to
2H, 6H, L12H, 12H, L24H, or 24H for playback.
13. COUNTER RESET button
Press to reset the counter to 00000.
14. DISPLAY button
Press to display the Main menu. Press again to show the
time display.
15. POSITION/VERTICAL ADJUST buttons (+/-)
• Pressing the (+) button moves the day and time display
• Pressing either button minimizes vertical jitter in the still
16. TRACKING buttons (+/-)
Press these buttons if noise is present during playback, reverse playback, or slow playback.
17. PICTURE control
Use this control to adjust picture quality between soft and
sharp.
18. VIDEO switch
Use the switch to select color or black and white recording
and playback.
DISPLAY
COUNTER
D
RESET
MODE
REC/PLAY
4
COUNTER MEMORY/
SKIP/INDEX
TIMER REC
A
5
REC
STOP
PLAY
PAUSE/
SHUTTLE HOLD
6
SHUTTLE
JOG/ADJUST
CLEAR/ ENTER/
REW
789BCE
FF
to the right. Pressing the (-) button moves the day and
time display down the screen. The display cannot be
adjusted if a warning is displayed.
mode or during fast playback. Refer to Section 9.4.3 for
details.
Figure 3. Front View
Pelco Manual C650M (12/98) 15
Loading...