Pelco TI57 User Manual

®

TI57 Thermal Insulation

for EH5700 Series Enclosures

Installation/Operation

Manual C1433M (6/95)

1.0 WARNINGS

Prior to installation and use of this product, the following
WARNINGS should be observed.

1. Installation and servicing should only be done by
Qualified Service Personnel and conform to all
Local codes.

2. Unless the unit is specifically marked as a NEMA
Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is
designed for indoor use only and it must not be
installed where exposed to rain and moisture.

3. Only use replacement parts recommended by
PELCO.

4. After replacement/repair of this unit’s electrical
components, conduct a resistance measurement
between line and exposed parts to verify the exposed
parts have not been connected to line circuitry.

2.0 SCOPE

The information contained in this manual covers the
TI57 Thermal Insulation Kit Installation.

2.1 DESCRIPTION

The TI57 Thermal Insulation Kit provides an improved
resistance to heat loss through the body of the enclosure
by adding a 1/4-inch thick polyurethane insulation to
the majority of the internal surfaces.

Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • [phone] or (1-559) 292-1981

FAX [phone] or (1-559) 292-3827

3.0 TI57 THERMAL INSULATION

NOTE: The camera mounting sled must be

removed for proper installation of the thermal
insulation, therefore, it should be done prior to
the enclosure installation. (- 1, -2, -3; heater/
blower/wiper kits must be removed prior to ther­mal insulation installation.)

4. Remove the adhesive backing, and carefully lay the
insulation in the body of the enclosure, pressing
firmly, taking care not to crease the insulation.

5. The insulation is very soft and will conform as needed
during the installation of the camera and lens.

3.2 LID INSULATION INSTALLATION

The TI57 thermal insulation sheets are designed to be
used with both 23-inch and 29-inch EH5700 and
EH5700L Series enclosures. If insulation is required
for an 23-inch enclosure, the excess insulation must be
removed along the factory-marked perforation. For 29­inch installations, no trimming is necessary. To install
the thermal insulation, perform the following steps:

3.1 BODY INSULATION INSTALLATION

1. Remove the necessary punch-out cable-feed pieces
from the insulation pad depending on the type of en­closure (EH5700 or EH5700L series) being used. Re­move the vent area pieces for (-1, -2, -3) ventilation
through the enclosure. (See Figures 1 and 2.)

2. To adjust the length of the insulation pad, tear the
insulation along the perforations from the end of the
pad to fit either the 23-inch standard or Legacy® ver­sion of the enclosure.

3. Position the pad around the press nuts in the center
of the body by folding the pad along its length. Posi­tion the insulation punch-out(s) to closely match the
position of the press nuts.

1. Unlatch the enclosure lid and raise.

2. Pop the gas spring off of the lid at the ball-joint con­nection. Make sure the lid is supported and not al­lowed to lay completely open - doing so will dam­age the lid hinge.

3. Remove the punch-out pieces from the insulation pad
that accommodate the sun shroud screws and the lid
arm on the inside of the enclosure lid.

4. Adjust the necessary length of the pad according to
the length of the enclosure.

5. Remove the adhesive backing, and carefully lay the
insulation in the lid of the enclosure, pressing firmly,
taking care not to crease the insulation.

6. Position the insulation around the sun shroud fas­teners on the inside of the lid. It may help to hold the
insulation in a folded manner while positioning.

7. Snap the gas spring ball joint to the lid, close the
enclosure.

29-inch

23-inch

23-inch

29-inch

Figure 1. Lid and Body Insulation Sheets

2 PELCO Manual C1433M (6/95)

NOTE: When using blanking plates (in extreme cold
conditions), leave the vent/blanking plate area of the
insulation in place for extra protection.

Lid

Lid Insulation

Body Insulation

Body Assembly

Figure 2. TI57 Thermal Insulation Installation

PELCO Manual C1433M (6/95) 3

4.0 WARRANTY AND RETURN
INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved
defective in material or workmanship for a period of one year after the date
of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex® Series products (multiplexers, server, and

keyboard).

• Three years on Camclosure

CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which have a five-year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy

DF5/DF8 Series fixed dome products.

• Two years on Spectra

ing when used in continuous motion applications.

• Two years on Esprit

wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300

Series network video recorders, and Endura
network-based video products.

• One year (except video heads) on video cassette recorders (VCRs).

Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in

continuous motion applications (that is, preset scan, tour and auto scan
modes).

Pelco will warrant all replacement parts and repairs for 90 days from the
date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to Pelco, Clovis, California. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident are not covered
under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or
loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract,
negligence, infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special,
incidental or consequential damages (including loss of use, loss of profit
and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The
Dealer may also have additional rights, which are subject to variation from
state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289­9100 or [phone] to obtain a Repair Authorization number (RA),
and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice

number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall
under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by
which the item was received by Pelco.

®

and fixed camera models, except the

®

, CM6700/CM6800/CM9700 Series matrix, and

®

, Esprit®, ExSite™, and PS20 scanners, includ-

®

and WW5700 Series window wiper (excluding

™

Series distributed

RETURNS

In order to expedite parts returned to the factory for repair or credit, please
call the factory at [phone] or [phone] to obtain an
authorization number (CA number if returned for credit, and RA number
if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking
and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the
assigned CA or RA number and freight should be prepaid. Ship to the
appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto
Rico, send goods to:

If you are located outside the continental U.S., Alaska, Hawaii or Puerto
Rico and are instructed to return goods to the USA, you may do one of the
following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:

If the goods are to be sent by a FREIGHT FORWARDER, send the goods
to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

®

PELCO

3500 Pelco Way

Clovis, CA 93612-5699 USA

[phone] • [phone]

FAX [phone] or [phone]

International customers call 1-559-292-1981 or

FAX [phone]

(Product specifications subject to change

without notice.)

C1433M

Pelco, the Pelco logo, Camclosure, Esprit,
Genex, Legacy, and Spectra are registered
trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.

© Copyright 1995, Pelco. All rights reserved.

4 PELCO Manual C1433M (6/95)