Pelco TI2350, TI2614-1, TI2614, TI2635, TI2650-1 User Manual

Sarix TI Series Camera

User Manual

C6622M

September 2019

Pelco Troubleshooting Contact Information

If the instructions provided fail to solve your problem, contact Pelco Product Support at 1-800-289-9100

(USA and Canada) or [phone] (international) for assistance. Be sure to have the serial number

available when calling.

Do not try to repair the unit yourself. Leave maintenance and repairs to qualified technical personnel only.

Chapter 1: Important Notices Sarix TI Series Camera User Manual

List of Revisions

No. Date Description Page Number

1.0 New Release All

1-1

Sarix TI Series Camera User Manual Chapter 1: Important Notices

Table of Contents

1. Important Notices ............................................................................................................................. 1-8

1.1 Regulatory Notices [FCC Class A] ..................................................................................................... 1-8

1.1.1 Radio and Television Interference ............................................................................................. 1-8

1.2 Legal Notice [Audio Notice] ............................................................................................................... 1-8

1.3 Video Quality Caution ........................................................................................................................ 1-9

1.3.1 Frame Rate Notice Regarding User Selected Options ............................................................... 1-9

1.4 Open Source Software ........................................................................................................................ 1-9

1.5 CCC Power Cord Statement ............................................................................................................... 1-9

1.5.1 2.4 GHZ Radio Device ............................................................................................................ 1-10

1.6 ESD Warning .................................................................................................................................... 1-10

1.7 Warranty ............................................................................................................................................ 1-10

1.8 Network Topology Statement ........................................................................................................... 1-10

2. Overview .......................................................................................................................................... 2-13

2.1 Overview ........................................................................................................................................... 2-14

2.2 Features ............................................................................................................................................. 2-14

2.3 Physical Description of the Camera .................................................................................................. 2-15

2.4 Marking ............................................................................................................................................. 2-16

2.5 Sarix TI Web GUI ............................................................................................................................. 2-17

2.6 Technical Data and Specifications .................................................................................................... 2-18

2.6.1 System Specifications .............................................................................................................. 2-18

2.6.2 Configurations ......................................................................................................................... 2-19

2.6.3 Thermal Camera ...................................................................................................................... 2-20

2.6.4 CMOS Camera ........................................................................................................................ 2-20

3. Safety .................................................................................................................................................. 3-1

3.1 Safety Conventions ............................................................................................................................. 3-1

3.2 Safety During Installation ................................................................................................................... 3-2

3.3 Safety During Maintenance ................................................................................................................ 3-2

4. Installation ......................................................................................................................................... 4-1

4.1 Unpacking ........................................................................................................................................... 4-1

4.2 Camera Installation ............................................................................................................................. 4-2

4.2.1 Installation Guidelines and Preparation .................................................................................... 4-2

4.2.2 Mechanical Interface Preparation .............................................................................................. 4-3

4.2.3 Wall Mount Configuration ........................................................................................................ 4-4

4.2.4 Pole Mount Configuration ......................................................................................................... 4-5

4.2.5 Electrical ICD IP PoE Cable ..................................................................................................... 4-6

5. Operation ........................................................................................................................................... 5-1

5.1 First Time Credentials Setup ............................................................................................................... 5-2

Chapter 1: Important Notices Sarix TI Series Camera User Manual

5.2 Logging Into Sarix TI Camera Web GUI ........................................................................................... 5-3

5.3 Changing Your Password ................................................................................................................... 5-5

5.4 Main Window Overview .................................................................................................................... 5-6

5.5 Live View Window ............................................................................................................................ 5-7

5.6 Status Window .................................................................................................................................... 5-8

5.6.1 System Tab ................................................................................................................................ 5-9

5.6.2 Thermal Tab ............................................................................................................................ 5-10

5.6.3 Day Tab ................................................................................................................................... 5-12

5.6.4 Disabling / Enabling a Camera ............................................................................................... 5-13

5.7 Network Window ............................................................................................................................. 5-15

5.7.1 Setting of IP Address .............................................................................................................. 5-16

5.7.2 Setting an Auto IP Address (DHCP) ....................................................................................... 5-16

5.7.3 Setting a Manual DNS Server Address ................................................................................... 5-17

5.7.4 Settings of HTTPS Connection ............................................................................................... 5-17

5.7.5 Setting the Network Interface ................................................................................................. 5-17

5.7.6 Resetting Network Settings ..................................................................................................... 5-18

5.7.7 Restarting ONVIF Service ...................................................................................................... 5-18

5.7.8 Certificates .............................................................................................................................. 5-19

5.8 Streaming Window ........................................................................................................................... 5-21

5.8.1 Thermal Tab ............................................................................................................................ 5-21

5.8.2 Day Tab ................................................................................................................................... 5-25

5.8.3 General Configuration Tab ..................................................................................................... 5-28

5.9 Image Processing Window ............................................................................................................... 5-29

5.9.1 Thermal Tab ............................................................................................................................ 5-29

5.9.2 Day Tab ................................................................................................................................... 5-37

5.10 Analytics Window ............................................................................................................................ 5-41

5.10.1 Regions Tab ............................................................................................................................ 5-42

5.10.2 Ignore Regions Tab ................................................................................................................. 5-46

5.10.3 Learning Tab ........................................................................................................................... 5-48

5.10.4 Analytics Settings .................................................................................................................... 5-49

5.11 System Window ................................................................................................................................ 5-51

5.11.1 Admin Tab .............................................................................................................................. 5-51

5.11.2 Logs Tab .................................................................................................................................. 5-57

5.11.3 Date and Time Tab .................................................................................................................. 5-58

5.11.4 File Upload Tab ....................................................................................................................... 5-60

5.11.5 User Management Tab ............................................................................................................ 5-60

5.12 Logging Out from the Web GUI ...................................................................................................... 5-62

6. Maintenance .................................................................................................................................... 6-63

6.1 Visual Inspection .............................................................................................................................. 6-63

6.2 Cleaning ............................................................................................................................................ 6-63

7. Ordering Information .................................................................................................................... 7-64

1-3

Sarix TI Series Camera User Manual Chapter 1: Important Notices

7.1 Ordering Information ........................................................................................................................ 7-64

7.2 Ordering Accessories ........................................................................................................................ 7-64

8. Index ................................................................................................................................................. 8-65

Chapter 1: Important Notices Sarix TI Series Camera User Manual

List of Figures

Figure 2-1: Sarix TI Camera General View .......................................................................................... 2-14

Figure 2-2: Physical Description of the Camera ................................................................................... 2-15

Figure 2-3: Sarix TI Label ..................................................................................................................... 2-16

Figure 2-4: Sarix TI Web GUI .............................................................................................................. 2-17

Figure 4-1: Sarix TI Camera Package General View .............................................................................. 4-1

Figure 4-2: Mechanical Interface Preparation - Camera Dimensions ..................................................... 4-3

Figure 4-3: Camera Installation - Wall Mount Configuration ................................................................ 4-4

Figure 4-4: Camera Installation - Pole Mount Configuration ................................................................. 4-5

Figure 4-5: Electrical ICD IP PoE Cable ................................................................................................ 4-6

Figure 5-1: Sarix TI Web GUI – First Time Setup ................................................................................. 5-2

Figure 5-2: Sarix TI Web GUI - Status Window (before Login) ............................................................ 5-3

Figure 5-3: Login Window ...................................................................................................................... 5-3

Figure 5-4: Login Window – Entering Username and Password ............................................................ 5-4

Figure 5-5: Sarix TI Web GUI - Status Window (after Login) ............................................................... 5-4

Figure 5-6: Changing Your Password - Drop Down Menu .................................................................... 5-5

Figure 5-7: Sarix TI Web GUI - Changing Your Password .................................................................... 5-5

Figure 5-8: Main Window Overview - Main Areas ................................................................................ 5-6

Figure 5-9: Live View Window (example) ............................................................................................. 5-7

Figure 5-10: Status Window (all collapsed) .............................................................................................. 5-8

Figure 5-11: Status Window - System Tab ............................................................................................... 5-9

Figure 5-12: Status Window - Thermal Tab ........................................................................................... 5-10

Figure 5-13: Status Window - Day Tab .................................................................................................. 5-12

Figure 5-14: Disabling / Enabling a Camera - System Reboot ............................................................... 5-13

Figure 5-15: Disabling / Enabling a Camera - System Reboot Approval ............................................... 5-14

Figure 5-16: Network Window - Basic Settings Tab .............................................................................. 5-15

Figure 5-17: Network Window - Changing an Address .......................................................................... 5-16

Figure 5-18: Network Window - Setting Network Interface .................................................................. 5-17

Figure 5-19: Network Window - Resetting IP Address Approval .......................................................... 5-18

Figure 5-20: Network Window - ONVIF Reload ................................................................................... 5-18

Figure 5-21: Certificates - Creating a Certificate Request ...................................................................... 5-19

Figure 5-22: Certificates - Generating a Self-Signed Certificate ............................................................ 5-19

Figure 5-23: Certificates - Uploading a Certificate ................................................................................. 5-20

Figure 5-24: Streaming Window - Thermal Tab ..................................................................................... 5-21

Figure 5-25: Streaming Window - Thermal Tab - Main Stream ............................................................. 5-22

Figure 5-26: Streaming Window - Thermal Tab - Secondary Stream .................................................... 5-24

Figure 5-27: Streaming Window - Day Tab - Main Stream .................................................................... 5-25

Figure 5-28: Streaming Window - Day Tab - Secondary Stream ........................................................... 5-27

Figure 5-29: Streaming Window - General Configuration Tab .............................................................. 5-28

Figure 5-30: Image Processing Window - Thermal Tab ......................................................................... 5-29

Figure 5-31: Image Processing Window - Thermal Tab - Basic Settings ............................................... 5-30

Figure 5-32: Image Processing Window - Thermal Tab - Signal Processing Settings ........................... 5-31

1-5

Sarix TI Series Camera User Manual Chapter 1: Important Notices

Figure 5-33: Image Processing Window - Thermal Tab - Gain Control Settings ................................... 5-32

Figure 5-34: Image Processing Window - Thermal Tab - Advanced Settings ........................................ 5-33

Figure 5-35: Image Processing Window - Thermal Tab - Color Processing Settings ............................. 5-34

Figure 5-36: Image Processing Window - Histogram Calculation ROI (1 of 3) ..................................... 5-34

Figure 5-37: Image Processing Window - Histogram Calculation ROI (2 of 3) ..................................... 5-35

Figure 5-38: Image Processing Window - Histogram Calculation ROI (3 of 3) ..................................... 5-36

Figure 5-39: Image Processing Window - Day Tab ................................................................................ 5-37

Figure 5-40: Image Processing Window - Day Tab - Geometry Settings ............................................... 5-38

Figure 5-41: Image Processing Window - Day Tab - Misc Properties Settings ...................................... 5-39

Figure 5-42: Analytics Window (all collapsed) ....................................................................................... 5-41

Figure 5-43: Analytics Window - Regions Tab ....................................................................................... 5-42

Figure 5-44: Analytics Window - Regions Tab - Region Options .......................................................... 5-43

Figure 5-45: Analytics Window - Regions Tab - Area ROI .................................................................... 5-45

Figure 5-46: Analytics Window - Regions Tab - Fence ROI .................................................................. 5-45

Figure 5-47: Analytics Window - Ignore Regions Tab ........................................................................... 5-46

Figure 5-48: Analytics Window - Ignore Regions Tab – Ignore Regions ROI (1 of 2) .......................... 5-47

Figure 5-49: Analytics Window - Ignore Regions Tab – Ignore Regions ROI (2 of 2) .......................... 5-47

Figure 5-50: Analytics Window - Learning Tab ..................................................................................... 5-48

Figure 5-51: Analytics Window - Analytics Settings .............................................................................. 5-49

Figure 5-52: System Window - Admin Tab ............................................................................................ 5-51

Figure 5-53: System Window - Admin Tab - Restart Aproval ............................................................... 5-51

Figure 5-54: System Window - Admin Tab - Restart .............................................................................. 5-52

Figure 5-55: System Window - Admin Tab - Archive System Files ...................................................... 5-52

Figure 5-56: System Window - Admin Tab - Save As Site Approval .................................................... 5-53

Figure 5-57: System Window - Admin Tab - Save As Site .................................................................... 5-53

Figure 5-58: System Window - Admin Tab - Export Site Approval ....................................................... 5-54

Figure 5-59: System Window - Admin Tab - Site Defaults Approval .................................................... 5-54

Figure 5-60: System Window - Admin Tab - Site Defaults .................................................................... 5-55

Figure 5-61: System Window - Admin Tab - Factory Defaults Approval .............................................. 5-55

Figure 5-62: System Window - Admin Tab - Factory Defaults .............................................................. 5-56

Figure 5-63: System Window - Logs Tab ............................................................................................... 5-57

Figure 5-64: System Window - Date and Time Tab ................................................................................ 5-58

Figure 5-65: System Window - Date and Time Tab - Synchronizing with Browser Time ..................... 5-59

Figure 5-66: System Window - Date and Time Tab - Synchronizing with NTP .................................... 5-59

Figure 5-67: System Window - File Upload Tab .................................................................................... 5-60

Figure 5-68: System Window - User Management Tab .......................................................................... 5-60

Figure 5-69: System Window - User Management Tab - Adding a User ............................................... 5-61

Figure 5-70: System Window - User Management Tab - Editing User Details ...................................... 5-62

Figure 5-71: Logging Out from the Web GUI - Drop Down Menu ........................................................ 5-62

Chapter 1: Important Notices Sarix TI Series Camera User Manual

List of Tables

Table 2-1: Technical Data and Specifications - System Specifications ............................................... 2-18

Table 2-2: Technical Data and Specifications - Configurations .......................................................... 2-19

Table 2-3: Technical Data and Specifications - Thermal Camera ....................................................... 2-20

Table 2-4: Technical Data and Specifications - CMOS Camera ......................................................... 2-20

Table 4-1: Electrical ICD IP PoE Cable - Pinout ................................................................................... 4-6

Table 7-1: Ordering Information for 30Hz Camera ............................................................................. 7-64

Table 7-2: Ordering Information for 9Hz Camera ............................................................................... 7-64

Table 7-3: Ordering Accessories .......................................................................................................... 7-64

1-7

Sarix TI Series Camera User Manual Chapter 1: Important Notices

1. Important Notices

1.1 Regulatory Notices [FCC Class A]

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

1.1.1 Radio and Television Interference

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can

void your authority to operate this equipment under Federal Communications Commission’s rules.

To maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation

with non-approved equipment or unshielded cables is likely to result in interference to radio and television

reception.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

1.2 Legal Notice [Audio Notice]

SOME PELCO EQUIPMENT CONTAINS, AND THE SOFTWARE ENABLES, AUDIO/VISUAL AND

RECORDING CAPABILITIES, THE IMPROPER USE OF WHICH MAY SUBJECT YOU TO CIVIL

AND CRIMINAL PENALTIES. APPLICABLE LAWS REGARDING THE USE OF SUCH

CAPABILITIES VARY BETWEEN JURISDICTIONS AND MAY REQUIRE, AMONG OTHER

THINGS, EXPRESS WRITTEN CONSENT FROM RECORDED SUBJECTS. YOU ARE SOLELY

RESPONSIBLE FOR INSURING STRICT COMPLIANCE WITH SUCH LAWS AND FOR STRICT

ADHERENCE TO ANY/ALL RIGHTS OF PRIVACY AND PERSONALTY. USE OF THIS

EQUIPMENT AND/OR SOFTWARE FOR ILLEGAL SURVEILLANCE OR MONITORING SHALL

BE DEEMED UNAUTHORIZED USE IN VIOLATION OF THE END USER SOFTWARE

Chapter 1: Important Notices Sarix TI Series Camera User Manual

AGREEMENT AND RESULT IN THE IMMEDIATE TERMINATION OF YOUR LICENSE RIGHTS

THEREUNDER.

1.3 Video Quality Caution

1.3.1 Frame Rate Notice Regarding User Selected Options

Pelco systems are capable of providing high quality video for both live viewing and playback. However,

the systems can be used in lower quality modes, which can degrade picture quality, to allow for a slower

rate of data transfer and to reduce the amount of video data stored. The picture quality can be degraded by

either lowering the resolution, reducing the picture rate, or both. A picture degraded by having a reduced

resolution may result in an image that is less clear or even indiscernible. A picture degraded by reducing

the picture rate has fewer frames per second, which can result in images that appear to jump or move more

quickly than normal during playback. Lower frame rates may result in a key event not being recorded by

the system.

Judgment as to the suitability of the products for users' purposes is solely the users' responsibility. Users

shall determine the suitability of the products for their own intended application, picture rate and picture

quality. In the event users intend to use the video for evidentiary purposes in a judicial proceeding or

otherwise, users should consult with their attorney regarding any particular requirements for such use.

1.4 Open Source Software

This product includes certain open source or other software originated from third parties that is subject to

the GNU General Public License (GPL), GNU Library/Lesser General Public License (LGPL) and

different and/or additional copyright licenses, disclaimers, and notices.

The exact terms of GPL, LGPL, and some other licenses are provided to you with this product. Please refer

to the exact terms of the GPL and LGPL at http://www.fsf.org (Free Software Foundation) or

http://www.opensource.org (Open Source Initiative) regarding your rights under said license. You may

obtain a complete corresponding machine-readable copy of the source code of such software under the GPL

or LGPL by sending your request to [e-mail]; the subject line should read Source Code

Request. You will then receive an email with a link for you to download the source code.

This offer is valid for a period of three (3) years from the date of the distribution of this product by Pelco.

1.5 CCC Power Cord Statement

Models shipped to China do not include power cords.

1-9

A CCC approved power cord must be used to power the equipment

WARNING: This product is sensitive to Electrostatic Discharge (ESD). To avoid ESD

Electrostatic Discharge Association (www.esda.org).

when used in China

1.5.1 2.4 GHZ Radio Device

1.6 ESD Warning

damage to this product, use ESD safe practices during installation. Before touching,
adjusting or handling this product, correctly attach an ESD wrist strap to your wrist and
appropriately discharge your body and tools. For more information about ESD control and
safe handling practices of electronics, please refer to ANSI/ESD S20.20-1999 or contact the

Sarix TI Series Camera User Manual Chapter 1: Important Notices

NOTE

1.7 Warranty

For information about Pleco's product warranty and thereto related information, refer to

www.pelco.com/warranty.

1.8 Network Topology Statement

IMPORTANT NOTE. PLEASE READ. The network implementation is shown as a general

representation only and is not intended to show a detailed network topology. Your actual network will

differ, requiring changes or perhaps additional network equipment to accommodate the system as

illustrated. Please contact your local Pelco representative to discuss your specific requirements.

Chapter 1: Important Notices Sarix TI Series Camera User Manual

List of Acronyms and Abbreviations

AWG: American Wire Gauge NUC: Non-Uniformity Correction

CBR: Constant Bit Rate NV: Night Vision

Histogram:

CE: Comminute European

CMOS:

DC: Direct Current QVGA+: Quarter Video Graphics Array (384 ×288)

DFPA:

DHCP:

Dynamic Host Configuration Protocol ROI: Region Of Interest

DNS:

Federal Communications Commission

FCC:

I-frame: Infra-coded frame RTSP:

FM:

FOV: Field Of View

FPS:

Ground SSL: Secure Sockets Layer

GND:

Accurate representation of the
distribution of numerical data.

ONVIF: Open Network Video Interface Forum

P/N: Part Number

Complementary Metal-Oxide
Semiconductor

Digital Focal Plan Array RH: Relative Humidity

Domain Name System RTN: Return

Power Over Ethernet

PoE:

RTP:

Real Time Protocol

Real-Time Streaming Protocol

Firmware

Frames Per Second VMS: Video Management System

S/N:

SDK:

Serial Number

Software Development Kit

GOP: Group of Pictures SW: Software

Graphical User Interface TCP: Transmission Control Protocol

GUI:

HD:

HTTP: Hypertexts Transfer Protocol TLS:

HTTPS: HyperText Transfer Protocol Secure URI:

IEEE:

IP: Internet Protocol

IR: Infrared VDC:

JPEG: Joint Photographic Expert Group

LAN: Local Area Network VGA:

MAC:

mK:

milli-Kelvin WWW: World Wide Web

NETD: Noise Equivalent Temperature

High Definition

Institute of Electrical and Electronics
Engineers

Media Access Control

Difference

TINT:

Transport Layer Security

V bus

VBR: Variable Bit Rate

Volts, Direct Current

VDDA:

Video Graphics Array (640 × 480)

VGSK:

Pipeline: data processing elements, connected in

Time Integration

Uniform Resource Indicator

CTIA reference voltage

Analog supply fixed

Compensation microbolometer - transistor
gate voltage

series, where the output of one element
is the input of the next one.

1-11

Scope of This Manual

This manual provides the necessary information for introducing, installing, operating and
maintaining the Sarix TI Series Camera.

The manual in intended for use by technicians and operators and consists of the following
chapters:

 Chapter 2: Overview:

Introduces the Sarix TI Series Camera and its web GUI features.

 Chapter 3: Safety:

Provides safety instructions that technicians should be aware of during the installation,
operation and maintenance of the Sarix TI Series Camera.

 Chapter 4: Installation:

Provides instructions for installing the Sarix TI Series Camera.

 Chapter 5: Operation:

Provides operating instructions for the Sarix TI Series Camera web GUI.

 Chapter 6: Maintenance:

Provides the Sarix TI Series Camera preventive maintenance instructions.

 Chapter 7: Ordering Information:

Provides information for purchasing the Sarix TI Series Camera and accessories.

 Index:

Provides a list, arranged in alphabetical order, of keywords found throughout this manual.

Sarix TI Series Camera User Manual Chapter 1: Important Notices

Chapter 2: Overview Sarix TI Series Camera User Manual

2. Overview

This chapter introduces the Sarix TI Series Camera and its web GUI features.

The chapter consists of the following sections:

 Section 2.1: Overview
 Section 2.2: Features
 Section 2.3: Physical Description of the Camera
 Section 2.5: Sarix TI Web GUI
 Section 2.6: Technical Data and Specifications

2-13

2.1 Overview

Sarix TI Camera is a state of the art observation system, boasting an incredibly easy installation
with thermal and visual capabilities. The Sarix TI line of cameras is a broad portfolio of high
performance outdoor rated cameras for 24/7 perimeter surveillance, observation, and monitoring
of critical infrastructure and sensitive sites.

Equipped with thermal and visible-light channels, the Sarix TI meets global Open Network
Video Interface Forum (ONVIF) standards to ensure interoperability of hardware and software
products for easy integration to both existing and new infrastructures, regardless of
manufacturer.

The Sarix TI is ruggedly designed to withstand the harshest weather and environmental
conditions, including rain, direct sunlight, high humidity, dust, heat, and cold.

The Sarix TI uses new and innovative open uncooled 17μ 640 x 480 or 384 x 288 resolution
thermal core and video enhancement algorithm.

Sarix TI Series Camera User Manual Chapter 2: Overview

Figure 2-1: Sarix TI Camera General View

2.2 Features

 Both visible and Video Graphics Array (VGA) thermal channels
 ONVIF Profile S compliant
 Easy installation
 Advanced optics
 Low cost of ownership
 Best support for analytics
 Rugged design
 Enhanced image processing

Chapter 2: Overview Sarix TI Series Camera User Manual

1

5

2

3 (x4)

4

Bottom View

2.3 Physical Description of the Camera

The Sarix TI Camera outer components include (see Figure 2-2):

1. Infrared (IR) Camera Lens

2. Main Connector (Power and Ethernet)

3. Camera-to-Pole Mount Adapter fastening screws (x4)

4. Tripod mount fastening screw

5. Complementary Metal-Oxide Semiconductor (CMOS) Camera Lens (module depended).

Figure 2-2: Physical Description of the Camera

2-15

2.4 Marking

The camera us marked with a label as shown below:

Sarix TI Series Camera User Manual Chapter 2: Overview

Figure 2-3: Sarix TI Label

NOTE: For reference only

Chapter 2: Overview Sarix TI Series Camera User Manual

2.5 Sarix TI Web GUI

The operation of the Sarix TI Camera is performed via Web Graphical User Interface (GUI).

With the GUI you can:

 Setup the camera operation.
 Optimize the camera video.
 Communicate with Video Management Systems (VMS).

Figure 2-4: Sarix TI Web GUI

2-17

2.6 Technical Data and Specifications

2.6.1 System Specifications

Applicable to models :Sarix TI 14.2mm, 35mm, and 50mm.

Table 2-1: Technical Data and Specifications - System Specifications

Thermal Camera: Imager Type: Uncooled ASi Microbolometer

Spectral Band: 7.5 - 14µ

Pixel Size: 17µ

Resolution: 640 x 480 (VGA) or 384 x 288 (QVGA)

NETD: VGA: < 40° mk, QVGA+: < 70° mk

Day Camera: Imager Type: ¼" CMOS

Resolutions: 640 x 480, 1024 x 768, or 1280 x 768

Field of View: 54° (H) x 42° (V) @ 1024 x 768

Sarix TI Series Camera User Manual Chapter 2: Overview

S/N Ratio: 36dB

Video: Dual Channel: 2 channels IP video

Compression: H.264, Motion JPEG

Frame Rate: 8.3Hz or 25Hz

Streaming: RTSP, Unicast, Multicast

Image Settings: Brightness, Sharpness, Contrast, Rotation: 0°, 90°,

180°, 270° Horizontal and Vertical Flip

Power
Requirements:

Environmental: Storage Temp: -40°C to +71°C (-40° F to +160° F)

Mechanical
Parameters:

Power Input: 12 - 32VDC or Power over Ethernet (IEEE

802.3af/802.3at)

Consumption: 7W typical, 20W max. (based on DC voltage)

Operating Temp: -40°C to +55°C (-40° F to +131° F)

Humidity: +40°C, 95% RH

Rating: IP66 (NEMA 4X equivalent)

Dimensions: - 135mm (w), 202mm (d), 169mm (h)

- 5.32" (w), 7.95" (d), 6.65" (h)

System
Integration:

Weight: - 14 and 35mm: 2.2kg,

- 50mm: 2.4kg,

Interfaces: ONVIF Profile S, Web GUI

Chapter 2: Overview Sarix TI Series Camera User Manual

EN 55032:12;

Network: Default IP: 192.168.0.20

RTSP Port: 8554

Protocols: IPv4, HTTP, HTTPS, SSL/TLS, RTSP, DHCP

Certifications: - CE

- FCC

- IP66

- UL and cUL

2.6.2 Configurations

EN 55024:2010+A1:2015;
EN 50130-4:11+A1:14;
EN 61000-3-2:14;
EN 61000-3-3:13;
EN 60950-1:06+A11:09+A1:10+A12:11+A2:13
UL 60950-1 2nd edition;

CAN/CSA-C22.2 No. 60950-1:07+Amend 1:2011

IEC 60950-1:05+A1:09+A2:13;
IEC 60950-22:16

Table 2-2: Technical Data and Specifications - Configurations

Day/Night Day

Configuration Type Thermal Camera & Lens Camera & Lens

VGA 17μ 640 x 480 Athermalized

Uncooled Thermal

QVGA+ 17μ 384 x 288 Athermalized

Uncooled Thermal

¼" Colour HD CMOS 1280 x 720
Autofocus

2-19

2.6.3 Thermal Camera

Table 2-3: Technical Data and Specifications - Thermal Camera

Configuration TI2X14 TI2X35 TI2X50

Thermal Type Uncooled

Thermal Core 17µ 640 x 480 (VGA) or

Lens Type Athermalized, Fixed Focus

Focal Length 14.2mm 35mm 50mm

Lens F # f/1.2 f/1.2 f/1.2

Horizontal FOV - VGA 42.1° 17.6° 12.4°

Horizontal FOV - QVGA+ 25.7° 10.6° 7.5°

Video Type H.264, Motion JPEG (25Hz

Sarix TI Series Camera User Manual Chapter 2: Overview

17µ 384 x 288 (QVGA+)

or 9Hz)

Spectral Band Spectral Band 7.5 - 14µ

NETD < 40° mk (VGA), < 70° mk

(QVGA+)

Digital Zoom 1x, 2x, 4x

Control Operation Polarity, NUC, Image Flip,

Image Rotation & Digital

Zoom

2.6.4 CMOS Camera

Table 2-4: Technical Data and Specifications - CMOS Camera

Imager Type: 1/4" Colour HD CMOS

Effective Pixels / Resolutions: 640 x 480 or 1024 x 768 or 1280 x 720

Lens Type: Autofocus

Imager FOV (H x V): 54° x 42°

S/N Ratio: 36dB

Additional Features: Configurable Resolutions, Digital Zoom

Chapter 3: Safety Sarix TI Series Camera User Manual

3. Safety

This chapter provides safety instructions that technicians should be aware of during the
installation, operation and maintenance of the Sarix TI Series Camera.

The chapter consists of the following sections:

 Section 3.1: Safety Conventions
 Section 3.2: Safety During Installation
 Section 3.3: Safety During Maintenance

3.1 Safety Conventions

In this manual, safety information is presented as warnings, cautions, and notes.

WARNING

An operating procedure, practice, and so forth, which if not correctly

followed, could result in personal injury or loss of life.

CAUTION

An operating procedure, practice, and so forth, which if not strictly

observed, could result in damage to, or destruction of equipment.

NOTE

An operating procedure, practice, and so forth that is essential

to highlight.

All procedures in this manual must be performed in accordance with

the applicable local regulations.

All local safety regulations apply. If the instructions in any section of
this manual contradict those of the applicable local regulations, the
instructions of the applicable local regulations will prevail.

3-1

3.2 Safety During Installation

To avoid injuries, follow standard safety regulations if mounting the Sarix TI Camera on an
elevated location.

3.3 Safety During Maintenance

 Warranty void if opening the Sarix TI camera.
 Do not touch the Sarix TI Camera optics with bare hands.
 Do not use any chemicals for cleaning the Sarix TI Camera. Use only wipes approved for

optical equipment. Failure to comply could result in damage to the Sarix TI Camera optical­lens and/or its surfaces.

Sarix TI Series Camera User Manual Chapter 3: Safety

3-2

Chapter 4: Installation Sarix TI Series Camera User Manual

4. Installation

This chapter provides instructions for installing the Sarix TI Series Camera.

The chapter consists of the following sections:

 Section 4.1: Unpacking
 Section 4.2: Camera Installation

4.1 Unpacking

A standard package contains the following:

 Sarix TI Camera
 18-pin round female cable-connector
 Ferrite
 Washer Lock
 Screw 6-32NCX1/4" SOC HD SS
 Terminal lug ring 16AWG stub size 6
 Package

Figure 4-1: Sarix TI Camera Package General View

4-1

4.2 Camera Installation

NOTE

Opening the Sarix TI Camera enclosure will void the product

warranty.

CAUTION

Avoid pointing the Sarix TI Camera at the sun.

4.2.1 Installation Guidelines and Preparation

Prepare your self-made IP PoE cable (cables are available for purchase, see

Table 7-3 for information).

4.2.1.1 Cable wires between camera and DC/PoE power supply should be 20-22AWG.

Sarix TI Series Camera User Manual Chapter 4: Installation

4.2.1.2 Both the camera ant the end-equipment connected to it should be permanently

connected to protective earth, using screw and washers. Wires should be made
of cupper. Minimal grounding cable is 14AWG.

4.2.1.3 In case of using DC power supply:

(1) The cables should be protected by fuse with maximal current of 3A

(2) The output current shall not exceed 3A after 60s

(3) The maximal output current of the power supply shall not exceed 7.5A

4.2.1.4 Power supply (either POE injector or DC power supply) should be safety

approved for local regulations.

4.2.1.5 Install the Ferrite on the operational cable as close as possible , max 5cm, from

the system.

4-2

Chapter 4: Installation Sarix TI Series Camera User Manual

4.2.2 Mechanical Interface Preparation

NOTE

It is recommended to check the functioning of the Sarix TI Camera

prior to the actual installation.

Figure 4-2 depicts the camera dimensions and mechanical interfaces.

Figure 4-2: Mechanical Interface Preparation - Camera Dimensions

4-3

4.2.3 Wall Mount Configuration

An arm for wall-mount is available for purchase (see Table 7-3 for information).

The dimensions of the arm are given in Figure 4-3:

Figure 4-3: Camera Installation - Wall Mount Configuration

Sarix TI Series Camera User Manual Chapter 4: Installation

4-4

Chapter 4: Installation Sarix TI Series Camera User Manual

4.2.4 Pole Mount Configuration

An adapter for pole-mount is available for purchase (see Table 7-3 for information).

The dimensions of the device are given in Figure 4-4 (note that the arm for wall-mount is
required, as well):

Figure 4-4: Camera Installation - Pole Mount Configuration

4-5

4.2.5 Electrical ICD IP PoE Cable

Connector Pin #

Connector Pin #

Signal Name

Ethernet\POE

2 1 ETH RX+

6 2 ETH RX-

11 3 ETH TX+

15 6 ETH TX-

12

5,4

POE +

14

7,8

POE -

DC Power Input

8

P.S (-)

12-32vDC RTN

9

P.S (+)

12-32vDC

Shield

Camera body

GND Stud

Shield

The cable is available for purchase (see Table 7-3 for information).

Cable Pinout (see Figure 4-5):

Table 4-1: Electrical ICD IP PoE Cable - Pinout

Sarix TI Series Camera User Manual Chapter 4: Installation

P1

P2 (RJ45)

Figure 4-5: Electrical ICD IP PoE Cable

4-6

Chapter 5: Operation Sarix TI Series Camera User Manual

5. Operation

This chapter provides operating instructions for the Sarix TI Series Camera web GUI.

The chapter consists of the following sections:

 Section 5.1: First Time Credentials Setup
 Section 5.2: Logging Into Sarix TI Camera Web GUI
 Section 5.3: Changing Your Password
 Section 5.4: Main Window Overview
 Section 5.5: Live View Window
 Section 5.6: Status Window
 Section 5.7: Network Window
 Section 5.8: Streaming Window
 Section 5.9: Image Processing Window
 Section 5.10: Analytics Window
 Section 5.11: System Window
 Section 5.12: Logging Out from the Web GUI

5-1

5.1 First Time Credentials Setup

1. Open your web browser.

2. Type the Sarix TI Camera default IP address (192.168.0.20) in the address bar and click

Enter. The First Time Setup window opens (example):

Figure 5-1: Sarix TI Web GUI – First Time Setup

Sarix TI Series Camera User Manual Chapter 5: Operation

NOTE

The First Time Setup window appears the first time a user accesses

the camera’s IP address.

3. Define the administrator username in the Admin Login section.

4. Define the administrator password in the Admin Password section.

5. Retype the same password in the Admin Password (confirm) section.

6. Click ADD. The administrator credentials are defined.

NOTE

After defining the administrator credentials, the Status window

opens (see Section 5.2).

5-2

Chapter 5: Operation Sarix TI Series Camera User Manual

5.2 Logging Into Sarix TI Camera Web GUI

1. Open your web browser.

2. Type the Sarix TI Camera default IP address (192.168.0.20) in the address bar and click

Enter. The Status window opens (example):

Figure 5-2: Sarix TI Web GUI - Status Window (before Login)

3. You may now view some default settings of your Sarix TI Camera by expanding the

System, Thermal or Day tabs.

4. Click . The Login window opens:

Figure 5-3: Login Window

NOTE

A user is able to login only after they set up their credentials for the

first time (see Section 5.1).

5-3

Sarix TI Series Camera User Manual Chapter 5: Operation

5. Enter your Username and Password:

Figure 5-4: Login Window – Entering Username and Password

6. Click . The following message is displayed on the lower-left corner of the screen

for three seconds, stating that you have successfully logged in. In addition, the Status
window opens:

Figure 5-5: Sarix TI Web GUI - Status Window (after Login)

You can now use the Sarix TI Web GUI.

5-4

Chapter 5: Operation Sarix TI Series Camera User Manual

5.3 Changing Your Password

1. From the upper-right drop-down menu select Change Password:

Figure 5-6: Changing Your Password - Drop Down Menu

The following opens:

Figure 5-7: Sarix TI Web GUI - Changing Your Password

5-5

2. Enter your Current Password.

3. Enter the New Password and re-enter in the New Password (Confirm) field.

4. Click . The system automatically logs out and the Login window reopen

(see Figure 5-3).

5. Log in using the new password. The Status window re-opens (see Figure 5-5).

5.4 Main Window Overview

The main areas in every window consist of the following:

Figure 5-8: Main Window Overview - Main Areas

Sarix TI Series Camera User Manual Chapter 5: Operation

Legend

:

1. Menu: maneuvering between the GUI main features/tabs.

2. The name of the currently opened feature/tab.

3. Available only after logging in; a drop-down menu, enables to change your password or log

out from the program.

4. The area where you can view and/or set the feature parameters.

5-6

Chapter 5: Operation Sarix TI Series Camera User Manual

5.5 Live View Window

The Live View window allows viewing the Sarix TI Camera live video.

1. Click Live View. The Live View window opens, containing a live video display of both

thermal and visual cameras (example):

Figure 5-9: Live View Window (example)

2. To freeze the live-view video click . Click to resume the live-view video.

3. To view the video in full screen click . Click the keyboard Esc key to resume.

4. To take a snapshot of the video and save elsewhere:

a. Click . A *.jpg file is created and downloaded into your PC. The file is saved in

your \Downloads folder.

- the file name of the thermal camera snapshot: proxycam-ir-Snapshot.

- the file name of the visual camera snapshot: proxycam-vis-Snapshot.

b. You can now move the file elsewhere.

5-7

5.6 Status Window

The Status window allows viewing some of the Sarix TI Camera parameters and settings.

1. Click Status. The Status window opens (all collapsed):

Sarix TI Series Camera User Manual Chapter 5: Operation

Figure 5-10: Status Window (all collapsed)

The Status window is comprised of three tabs:

 System Tab: allows viewing general parameters related to the camera settings and its

software/firmware (see Section 5.6.1).

 Thermal Tab: allows viewing parameters related to the thermal camera settings and its

software/firmware (see Section 5.6.2).

 Day Tab: allows viewing parameters related to the visual camera settings and its

software/firmware (see Section 5.6.3).

 Disabling / Enabling a Camera: allows disabling the thermal camera and/or the visual

camera and enable them (see Section 5.6.4).

5-8

Chapter 5: Operation Sarix TI Series Camera User Manual

5.6.1 System Tab

The System tab allows viewing general parameters related to the camera settings and its
software/firmware.

Expand the System tab. The following opens:

Figure 5-11: Status Window - System Tab

The System tab consists of the following parameters:

 System temperature: the "System On Chip" temperature.
 System up time: the operating time since the last camera startup.
 System load: a coded indication on how the system is busy.
 ONVIF service URI: the Uniform Resource Indicator (URI), e.g., the ONVIF device web

service address.

 IP address: the camera IP address.
 Product: the camera name.
 Serial number: the system Serial Number (S/N).
 Firmware version: the version of the installed Firmware (FM).
 Build date: the date of the FM creation.
 MAC address: the camera unique Media Access Control (MAC) address.

5-9

5.6.2 Thermal Tab

The Thermal tab allows viewing parameters related to the thermal camera settings and its
software/firmware.

Expand the Thermal tab. The following opens:

Sarix TI Series Camera User Manual Chapter 5: Operation

Figure 5-12: Status Window - Thermal Tab

5-10

Chapter 5: Operation Sarix TI Series Camera User Manual

The Thermal tab consists of the following parameters:
 Pipeline ID: the current name of the pipeline (data processing elements, connected in series,

where the output of one element is the input of the next one).

 Pipeline Running: is the pipeline running?
 Pending Updates: does the pipeline requires initialization?
 Actual FPS: the current frame-rate where the pipeline is running.
 DFPA: indication from the thermal camera.
 Firmware version: indication from the thermal camera.
 Gain: indication from the thermal camera.
 Frame rate [Hz]: indication from the thermal camera.
 Serial number: indication from the thermal camera.
 Software version: indication from the thermal camera.
 TINT: indication from the thermal camera.
 Sensor temp [°C]: indication from the thermal camera.
 V bus: indication from the thermal camera.
 VDDA: indication from the thermal camera.
 VGFID: indication from the thermal camera.
 VGSK: indication from the thermal camera.
 VT bias: indication from the thermal camera.
 VTOFS1: indication from the thermal camera.
 VTOFS2: indication from the thermal camera.

5-11

5.6.3 Day Tab

The Day tab allows viewing parameters related to the thermal camera settings and its
software/firmware.

Expand the Day tab. The following opens:

Sarix TI Series Camera User Manual Chapter 5: Operation

Figure 5-13: Status Window - Day Tab

The Day tab consists of the following parameters:

 Pipeline ID: the current name of the pipeline.
 Pipeline Running: is the pipeline running?
 Pending Updates: does the pipeline requires initialization?
 Actual FPS: the current frame-rate where the pipeline is running.

5-12

Chapter 5: Operation Sarix TI Series Camera User Manual

5.6.4 Disabling / Enabling a Camera

This option allows to disable the thermal camera and/or the CMOS camera and re-enable them.

5.6.4.1 Disabling the Camera

1. Expand the Thermal / Day tab and click . The following opens:

2. Click OK to approve. The following opens while the system re-boots:

Figure 5-14: Disabling / Enabling a Camera - System Reboot

5-13

Sarix TI Series Camera User Manual Chapter 5: Operation

On completion, the following opens stating that the corresponding camera is disabled:

Figure 5-15: Disabling / Enabling a Camera - System Reboot Approval

The camera view does not appear anymore on the Live View window.

5.6.4.2 Enabling the Camera

1. Expand the Thermal / Day tab and click . The following opens:

2. Click OK to approve. The system re-boots (see Figure 5-14).
On completion, a message is displayed stating that the system has restarted
(see Figure 5-15).

The camera view is now available on the Live View window.

5-14

Chapter 5: Operation Sarix TI Series Camera User Manual

5.7 Network Window

The Network window allows configuring the HOST-to-Camera Ethernet communication
method.

1. Click Network. The Ethernet window - Basic Settings tab opens:

Figure 5-16: Network Window - Basic Settings Tab

5-15

5.7.1 Setting of IP Address

To change the IP address, Subnet mask or Gateway values:

1. Click on the corresponding address and change the value either using the button or type

the IP address using the keyboard. An example is shown in Figure 5-17:

Figure 5-17: Network Window - Changing an Address

Sarix TI Series Camera User Manual Chapter 5: Operation

2. Click for the changes to take effect (click to revert your

changes).

5.7.2 Setting an Auto IP Address (DHCP)

To set a dynamically assigned IP address:

1. Select the Obtain IP address automatically checkbox. Results:

- The address area turns invalid.

- the DNS area become valid.

2. To let the system to select an auto DNS server address: enable the DNS area by selecting

the Obtain IP address automatically checkbox. The Obtain DNS servers automatically
checkbox is automatically selected.

3. Click for the changes to take effect (click to revert your changes).

5-16

Chapter 5: Operation Sarix TI Series Camera User Manual

5.7.3 Setting a Manual DNS Server Address

This option is applicable when you wish to synchronize the time and date with a DNS server
(see Section 5.11.3.2).

To manually select a DNS server address:

1. Enable the DNS area by selecting the Obtain IP address automatically checkbox. The

Obtain DNS servers automatically checkbox is automatically selected.

2. Clear the Obtain DNS servers automatically checkbox.

3. Click . An empty DNS line is added.

4. Determine the address.

5. Click for the changes to take effect (click to revert your changes).

5.7.4 Settings of HTTPS Connection

This option is applicable when selecting either a self-signed certificate or uploading an existing
certificate (see Section 5.7.7).

To set the HTTPS connection:

1. Set the HTTPS Port bar to the required value (1 to 65535).

2. Click for the changes to take effect (click to revert your changes).

5.7.5 Setting the Network Interface

To have the network interface permanently set to 100 Mbps:

1. Select the Advanced tab. The following opens:

Figure 5-18: Network Window - Setting Network Interface

2. Select the Fix network speed to 100Mbit full duplex checkbox.

5-17

5.7.6 Resetting Network Settings

To revert network settings back to factory defaults:

1. Click . The following opens:

Figure 5-19: Network Window - Resetting IP Address Approval

2. Click OK to revert network settings back to factory defaults.

5.7.7 Restarting ONVIF Service

To restart the system and reload ONVIF service:

Click . The following opens while the system re-starts:

Sarix TI Series Camera User Manual Chapter 5: Operation

Figure 5-20: Network Window - ONVIF Reload

NOTE

The HTTPS Port default value is 443.

5-18

Chapter 5: Operation Sarix TI Series Camera User Manual

5.7.8 Certificates

5.7.8.1 Creating a Certificate Request

This option allows retrieval of a Secure Sockets Layer (SSL) certificate.

1. Select the Certificates tab. The following opens:

Figure 5-21: Certificates - Creating a Certificate Request

2. Enter/select the following details:

• Common Name (compulsory; an IP address or system Host name).

• State or Province

• Country (select from the drop-down list)

• City

• Organization

• Department

3. Click . Your request is submitted for approvals.

5.7.8.2 Generating a Self-Signed Certificate

This option allows producing a self-made certificate.

1. Select the Generate Self-Signed Certificate option. The following opens:

Figure 5-22: Certificates - Generating a Self-Signed Certificate

5-19

Sarix TI Series Camera User Manual Chapter 5: Operation

2. Enter/select the following details:

• Common Name (compulsory; an IP address or system Host name).

• State or Province

• Country (select from the drop-down list)

• City

• Organization

• Department

• Validity (in days)

3. Click . Your self-signed certificate is submitted for approvals.

5.7.8.3 Uploading a Certificate

This option allows loading an existing certificate, originated by another source.

1. Select the Upload Certificate option. The following opens:

Figure 5-23: Certificates - Uploading a Certificate

2. Click and browse to select the certificate file (*.pem format).

3. Click . Your uploaded certificate is submitted.

5-20

Chapter 5: Operation Sarix TI Series Camera User Manual

5.8 Streaming Window

The Streaming window allows configuring the video flow-rate and the video encoding method.

5.8.1 Thermal Tab

1. Click Streaming. The Streaming - Thermal Tab opens:

Figure 5-24: Streaming Window - Thermal Tab

2. Under each option in the Thermal Tab you can:

• Click to restart the video streaming.

• Click to stop the video streaming.

• Click to re-start the video streaming.

5-21

Sarix TI Series Camera User Manual Chapter 5: Operation

5.8.1.1 Main Stream

Expand the Main Stream option. The following opens (click for the changes to take
effect; click to revert your changes):

Figure 5-25: Streaming Window - Thermal Tab - Main Stream

The main stream option consists of the following parameters:
 Misc Properties parameters:

• CBR: the video flow-rate (Kb/Sec).

• IntraQp: an auto calculation of the I-level quality-level (default: -1).

• VBR quality factor: 1 is the lowest level (applies only for VBR).

• Rate Control: Constant Bit Rate (CBR) or Variable Bit Rate (VBR).

• GOP: Group Of Pictures; how many frames will include an Intra-Frame.

5-22

Chapter 5: Operation Sarix TI Series Camera User Manual

• Unit Type: selection of the installed camera/lens type and the installation method.

• Video Encoding: selection of the video coding (mjpeg requires a system restart).

• Image Size/Rate: selection of the video that will be taken from the camera.

5-23

Sarix TI Series Camera User Manual Chapter 5: Operation

5.8.1.2 Secondary Stream

Expand the Secondary Stream option. The following opens (click for the changes to
take effect; click to revert your changes):

Figure 5-26: Streaming Window - Thermal Tab - Secondary Stream

The secondary stream option consists of the following parameters:

 VBR quality factor: 1 is the lowest level.
 GOP I-frame spacing: Group Of Pictures; how many frames will include an Intra-Frame.
 Video encoding: selection of the video coding (mjpeg requires a system restart).

5-24

Chapter 5: Operation Sarix TI Series Camera User Manual

5.8.2 Day Tab

Under each option in the Day Tab you can:

• Click to restart the video streaming.

• Click to stop the video streaming.

• Click to re-start the video streaming.

5.8.2.1 Main Stream

Expand the Main Stream option. The following opens (click for the changes to take
effect; click to revert your changes):

Figure 5-27: Streaming Window - Day Tab - Main Stream

5-25

The main stream option consists of the following parameters:

• CBR: the video flow-rate (Kb/Sec).

• IntraQp: an auto calculation of the I-level quality-level (default: -1).

• VBR quality factor: 1 is the lowest level (applies only for VBR).

• Rate Control: CBR or VBR.

• GOP: Group Of Pictures; how many frames will include an Intra-Frame.

Sarix TI Series Camera User Manual Chapter 5: Operation

• Unit Type: selection of the installed camera/lens type and the installation method.

• Video Scale: the video resolution; "NO CHANGE": 1280 x 720 (HD).

• Video Encoding: selection of the video coding (mjpeg requires a system restart).

• Image Size/Rate: selection of the video that will be taken from the camera.

5-26

Chapter 5: Operation Sarix TI Series Camera User Manual

5.8.2.2 Secondary Stream

Expand the Secondary Stream option. The following opens (click for the changes to
take effect; click to revert your changes):

Figure 5-28: Streaming Window - Day Tab - Secondary Stream

The secondary stream option consists of the following parameters:

 VBR quality factor: 1 is the lowest level.
 GOP I-frame spacing: Group Of Pictures; how many frames will include an Intra-Frame.
 Video encoding: selection of the video coding (mjpeg requires a system restart).

5-27

5.8.3 General Configuration Tab

Select the General Configuration tab. The following opens (click for the changes to
take effect; click to revert your changes):

Figure 5-29: Streaming Window - General Configuration Tab

Sarix TI Series Camera User Manual Chapter 5: Operation

The General Configuration tab consists of the following parameters:

 Enable Authentication: user/password enabled.
 RTSP Port: the RTSP port.
 RTSP Over HTTP Enabled
 RTSP Over HTTP Port

5-28

Chapter 5: Operation Sarix TI Series Camera User Manual

EYE-Q™

5.9 Image Processing Window

The Image Processing window allows changing the video display method, orientation and
quality.

Click Image Processing. The Image Processing - Thermal tab opens.

5.9.1 Thermal Tab

1. You can:

• From the Active Pipeline drop-down list select the pipeline name that is currently

active (either Night Vision - NV or EyeQ):

NV

• Click to restart the video streaming.

• Click to stop the video streaming.

• Click to re-start the video streaming.

Figure 5-30: Image Processing Window - Thermal Tab

5-29

Sarix TI Series Camera User Manual Chapter 5: Operation

2. Applicable for video processing only: click to revert the entire

settings to your local site settings. The following opens:

3. Click OK to approve.

4. Click for the changes to take effect (click to revert your

changes).

5.9.1.1 Basic Settings

Expand the Basic Settings option. The following opens (click for the changes to take
effect; click to revert your changes):

Figure 5-31: Image Processing Window - Thermal Tab - Basic Settings

5-30

Chapter 5: Operation Sarix TI Series Camera User Manual

White Hot

Black Hot

The Basic Settings option consists of the following parameters:
 Black hot: select ("Black Hot") or Clear ("White Hot") the Black Hot checkbox. After

clicking , the video image display is changing accordantly (example):

 Gamma: Gamma level corrections.

5.9.1.2 Signal Processing Settings

1. Expand the Basic Settings option. The following opens (click for the changes to

take effect; click to revert your changes):

Figure 5-32: Image Processing Window - Thermal Tab - Signal Processing Settings

2. Set the Noise filter level: filtering noises. It is recommended to remain with

the default value (high-value filtering will result in movement smudge).

5-31

Sarix TI Series Camera User Manual Chapter 5: Operation

5.9.1.3 Gain Control Settings

Expand the Gain Control option. The following opens (click for the changes to take
effect; click to revert your changes):

Figure 5-33: Image Processing Window - Thermal Tab - Gain Control Settings

The Gain Control option consists of the following parameters:
 Bad picture pacifier: noise-level deductions. It is recommended to remain with the default

value.

 Gray Levels: the quantity of the gray-levels (up to 200).

5-32

Chapter 5: Operation Sarix TI Series Camera User Manual

5.9.1.4 Advanced Settings

Expand the Advanced Settings option. The following opens (click for the changes to
take effect; click to revert your changes):

Figure 5-34: Image Processing Window - Thermal Tab - Advanced Settings

The Advanced Settings option consists of the following parameters:

 Edge Contrast: enhancement of the image contrast.
 Edge Enhancement: enhancement of the image edges.

5-33

Sarix TI Series Camera User Manual Chapter 5: Operation

5.9.1.5 Color Processing Settings

1. Expand the Color Processing option. The following opens (click for the changes

to take effect; click to revert your changes):

Figure 5-35: Image Processing Window - Thermal Tab - Color Processing Settings

2. Click . The following opens (example):

Figure 5-36: Image Processing Window - Histogram Calculation ROI (1 of 3)

5-34

Chapter 5: Operation Sarix TI Series Camera User Manual

3. Select the Allow Region Editing checkbox allowing to define an ROI on the

image. The Regions and Sub-Regions areas are enabled.

4. Click the + sign to enable more than one sub-region.

5. Select SubRegion-1 and mark an ROI on the image using the mouse

(example):

Figure 5-37: Image Processing Window - Histogram Calculation ROI (2 of 3)

6. Click . The Sub Region area is highlighted on the image and the

histogram is automatically calculated and saved (the image processing only
focuses on the pixels on the pixels within the ROI).

5-35

Sarix TI Series Camera User Manual Chapter 5: Operation

7. If more than one SubRegion is defined: select SubRegion-2 and mark an

ROI on the image using the mouse (example):

Figure 5-38: Image Processing Window - Histogram Calculation ROI (3 of 3)

8. Click to define the selected area as the reference for the

calculation.

9. Click . The Sub Region area is highlighted on the image and the

histogram is automatically calculated and saved.

10. To delete a Sub Region definitions: select the Sub Region (SubRegion-1 or

SubRegion-2 in the example) and click the - sign.

11. Clear the Allow Region Editing checkbox. The image is cleared from the

ROI markings and the buttons are disabled.

5-36

Chapter 5: Operation Sarix TI Series Camera User Manual

NV

EYE-Q™

5.9.2 Day Tab

1. You can:

• From the Active Pipeline drop-down list select the pipeline name that is currently

active (Night Vision - NV, or EyeQ):

• Click to restart the video streaming.

• Click to stop the video streaming.

• Click to re-start the video streaming.

Figure 5-39: Image Processing Window - Day Tab

5-37

Sarix TI Series Camera User Manual Chapter 5: Operation

2. Applicable for video processing only: click to revert the entire

settings to your local site settings (saved during Section 5.11.1.4: Save As

Site). The following opens:

3. Click OK to approve.

4. Click for the changes to take effect (click to revert your

changes).

5.9.2.1 Geometry Settings

Expand the Geometry Settings option. The following opens (click for the changes to
take effect, click to revert your changes):

Figure 5-40: Image Processing Window - Day Tab - Geometry Settings

5-38

Chapter 5: Operation Sarix TI Series Camera User Manual

The Geometry Settings option consists of the following parameter:

 Digital Zoom Level:

5.9.2.2 Misc. Properties Settings

Expand the Misc Properties Settings option. The following opens (click for the
changes to take effect, click to revert your changes):

Figure 5-41: Image Processing Window - Day Tab - Misc Properties Settings

5-39

Sarix TI Series Camera User Manual Chapter 5: Operation

The Misc. Properties Settings option consists of the following detector parameters:

 Brightness
 Color Effects
 Contrast
 Focus, Absolute: 0: Automatic, 1: infinity (recommended).
 Horizontal Flip
 Hue
 Saturation
 Vertical Flip
 White Balance, Automatic: not active.

5-40

Chapter 5: Operation Sarix TI Series Camera User Manual

5.10 Analytics Window

The Analytics Window enables detecting and tracking movement within predefined ROIs, as
well as for teaching the system where movement typically occurs.

1. Click Analytics. The Analytics window opens (all collapsed):

Figure 5-42: Analytics Window (all collapsed)

The Analytics window is comprised of three tabs:

 Regions Tab: enables marking of regios to detect movement (see Section 5.10.1).
 Ignore Regions Tab: enables marking of regions in which movement is ignored (see Section

5.10.2).

 Learning Tab: enables the system to learn the viewed scene and where movement typically

occurs (see Section 5.10.3).

NOTE

When entering the Analytics window, either of the following

messages is displayed on the lower-left corner of the screen,

depending on whether VMD is active or disabled. Click OK to close

these messages.

5-41

To enable/disable viewing analytics, click in the top-left

corner of the screen to toggle between enable and disable. Click

changes).

5.10.1 Regions Tab

The Regions tab enables marking regions to detect movement.

1. Expand the Regions tab. The following opens:

Sarix TI Series Camera User Manual Chapter 5: Operation

NOTE

for the changes to take effect (click to revert your

Figure 5-43: Analytics Window - Regions Tab

5-42

Chapter 5: Operation Sarix TI Series Camera User Manual

2. Click the + sign. The following opens (example):

Figure 5-44: Analytics Window - Regions Tab - Region Options

3. Click in the Name field and enter a region name.

4. Select region type from the following options:

 Area – detection is done within a close frame.
 Fence – detection is done for objects moving towards a predefined line.

NOTE

Some region options change depending on the type of region

selected.

5-43

Sarix TI Series Camera User Manual Chapter 5: Operation

5. Select the following parameters:

• Minimum Detection Size: determines the size and characters of the object to be

detected.

• ONVIF Alert: enabling receiving alerts which conform to ONVIF protocol.

• Maximum Speed: fastest speed that will be detected, in m/sec (default: 1 m/sec)

• Area Direction: determines the type of object movement (in relation to the region) that

will be detected (this option is available when Area type region is selected)

• Fence direction: determines the type of object movement (in relation to the fence line)

that will be detected (this option is available when Fence type region is selected)

5-44

Chapter 5: Operation Sarix TI Series Camera User Manual

6. Click the live image to mark the region frame points.

7. Double click the region starting point to end the region marking.

Figure 5-45: Analytics Window - Regions Tab - Area ROI

Figure 5-46: Analytics Window - Regions Tab - Fence ROI

5-45

NOTE

The color next to the region name corresponds with the color of the

region marked on the image.

8. To delete a region definition: select the region (Region-1 or Region-2 in the

example) and click the - sign.

9. Click for the changes to take effect (click to revert your

changes).

5.10.2 Ignore Regions Tab

The Ignore Regions tab enables marking regions in which movement is ignored.

Expand the Ignore Regions tab. The following opens:

Figure 5-47: Analytics Window - Ignore Regions Tab

Sarix TI Series Camera User Manual Chapter 5: Operation

5-46

Chapter 5: Operation Sarix TI Series Camera User Manual

1. Click the + sign. The following opens (example):

Figure 5-48: Analytics Window - Ignore Regions Tab – Ignore Regions ROI (1 of 2)

2. Click the live image to mark the Ignore Region frame points.

3. Double click the region starting point to end the Ignore Region marking.

Figure 5-49: Analytics Window - Ignore Regions Tab – Ignore Regions ROI (2 of 2)

5-47

4. To delete an Ignore Region definition: select the ignore region

(IgnoreRegion-1 or IgnoreRegion-2 in the example) and click the - sign.

5. Click for the changes to take effect (click to revert your

changes).

5.10.3 Learning Tab

The Learning tab enables the system to learn the scene and where movement typically occurs.

Expand the Learning tab. The following opens:

Sarix TI Series Camera User Manual Chapter 5: Operation

Figure 5-50: Analytics Window - Learning Tab

1. Click either of the following buttons:

• Click to start the learning session.

• Click to resume the learning session after the Stop button was activated.

• Click to stop the learning session (if, for example, unusual activity is

occurring).

• Click to delete the learning session in progress.

NOTE

VMD must be active (i.e., the toggle button in the top-left corner of

the screen must appear like this: ) to start the learning

session.

5-48

Chapter 5: Operation Sarix TI Series Camera User Manual

NOTE

When the Start button is pressed, the following message is displayed

on the lower-left corner of the screen. Click OK to close this

message.

5.10.4 Analytics Settings

Click in the upper-right corner of the screen. The following opens:

Figure 5-51: Analytics Window - Analytics Settings

5-49

Sarix TI Series Camera User Manual Chapter 5: Operation

The Analytics Settings window consists of the following parameters:
 ActiveBlockPercent: Percentage of the block area that should be active in order to detect

movement (default: 70%)

 BlockSize: minimum block size (default: 8)
 Draw Region: enabling drawing of region
 Draw Target Box: enabling frame overlay around the moving target
 Draw Target Trail: enabling trail showing the path the moving target has taken. The

maximum trail length is determined by “MaxTargetTrailLength”

 Initial Noise Level: higher level reduces the effect of noise in a scene, but also reduces

detection sensitivity (default: 6)

 LearningTime: length of time, in seconds, the learning session will run (default: 30 seconds)
 MaxTargetTrailLength: trail length, in FPS (default: 120 FPS). Will not display if “Draw

Target Trail” is not enabled

 Scene History: minimum number of frames that are used for movement detection (default:

2)

 TTL: length of time, in seconds, a target will continue to be considered a target after it

hasn’t been seen (default: 2 seconds)

 Track All Frame: enabling tracking of target in entire image frame, not just in the ROI the

object was detected in

 Warning Time: elapsed time, in seconds, until the system defines the identified object as a

target (default: 0.4 seconds)

NOTE

To close the Analytics Settings screen, click in the upper-right

corner of the screen. Any changes that were made are retained.

5-50

Chapter 5: Operation Sarix TI Series Camera User Manual

5.11 System Window

The System Window consists of five tabs:

 Admin Tab (see Section 5.11.1)
 Logs Tab (see Section 5.11.2)
 Date and Time Tab (see Section 5.11.3)
 File Upload Tab (see Section 5.11.4)
 User Management Tab (see Section 5.11.5)

5.11.1 Admin Tab

Click ADMIN. The following opens:

Figure 5-52: System Window - Admin Tab

5.11.1.1 Restart

To completely restart the entire system:

1. Click . The following opens:

Figure 5-53: System Window - Admin Tab - Restart Aproval

5-51

Sarix TI Series Camera User Manual Chapter 5: Operation

2. Click OK to approve the system restart. The following opens, stating that the

restart process could take a few minutes:

Figure 5-54: System Window - Admin Tab - Restart

On completion, the following opens prompting that the restart is completed:

5.11.1.2 Archive System Files

To archive the entire system files:

1. Click . The following opens, prompting that the archiving is in process:

Figure 5-55: System Window - Admin Tab - Archive System Files

5-52

Chapter 5: Operation Sarix TI Series Camera User Manual

On completion, the following opens prompting to approve the download of the archived file:

2. Click Yes to download the file. The file is downloaded and saved in your

\Downloads folder. File name: System-files.tgzx.

5.11.1.3 Save As Site

To save the current settings of the camera and the GUI as site defaults:

1. Click . The following opens:

Figure 5-56: System Window - Admin Tab - Save As Site Approval

2. Click OK to proceed. The following opens, prompting that site defaults save

is in process:

Figure 5-57: System Window - Admin Tab - Save As Site

5-53

Sarix TI Series Camera User Manual Chapter 5: Operation

On completion, the following opens prompting that the site defaults are saved:

5.11.1.4 Export Site

To download an archived file that contain the site defaults:

1. Click . The following opens prompting to approve the site defaults download:

Figure 5-58: System Window - Admin Tab - Export Site Approval

2. Click Yes to download the file with DHCP, OR:

Click No to download the file with a constant IP address.
The file is downloaded and saved in your \Downloads folder. File name:

site-defaults.tgzx.

5.11.1.5 Site Defaults

To revert system settings back to the site defaults settings:

1. Click . The following opens prompting to approve the revert process:

Figure 5-59: System Window - Admin Tab - Site Defaults Approval

5-54

Chapter 5: Operation Sarix TI Series Camera User Manual

2. Click OK. The following opens, prompting that the site defaults restoration

is in process:

Figure 5-60: System Window - Admin Tab - Site Defaults

On completion, the following opens prompting that the site defaults are saved:

5.11.1.6 Factory Defaults

To revert settings to factory defaults:

1. Click . The following opens prompting to approve the revert process:

Figure 5-61: System Window - Admin Tab - Factory Defaults Approval

NOTE

If Preserve IP is unchecked, the system will restart with the default
IP.

5-55

If Preserve Users is unchecked, all users will be deleted upon
system restart.

Sarix TI Series Camera User Manual Chapter 5: Operation

2. Click OK. The following opens, prompting that the factory defaults restoration is in process:

Figure 5-62: System Window - Admin Tab - Factory Defaults

On completion, the following opens prompting that the factory defaults are saved:

5-56

Chapter 5: Operation Sarix TI Series Camera User Manual

5.11.2 Logs Tab

The Status tab allows downloading data files from the Sarix TI Camera. This is mainly useful
when troubleshooting possible Sarix TI Camera malfunctions by Pelco’s technical support team.

1. Click System and select Log Files. The Status tab displays a list of logs (example):

Figure 5-63: System Window - Logs Tab

2. To refresh the list click .

5-57

5.11.3 Date and Time Tab

Time synchronization is extremely important for the ONVIF

handshake. If the time is not correctly synchronized, the camera may

not connect over ONVIF.

The Date and Time tab allows synchronizing of the Sarix TI Camera time and date according to
several methods:

Click System and select the DATE & TIME tab. The Date & Time tab opens:

Figure 5-64: System Window - Date and Time Tab

Sarix TI Series Camera User Manual Chapter 5: Operation

CAUTION

5-58

Chapter 5: Operation Sarix TI Series Camera User Manual

5.11.3.1 Synchronizing with Browser Time

Select the Synchronize with browser time option. The following opens:

Figure 5-65: System Window - Date and Time Tab - Synchronizing with Browser Time

5.11.3.2 Synchronizing with NTP

Select the Synchronize with NTP option. The following opens:

Figure 5-66: System Window - Date and Time Tab - Synchronizing with NTP

5-59

5.11.4 File Upload Tab

The File Upload tab allows updating your Sarix TI Camera with FM/SW.

1. Click System and select the FILE UPLOAD tab. The File Upload tab opens:

Figure 5-67: System Window - File Upload Tab

2. Click to browse and select the required FM/SW file (*.tgzx file

format).

Sarix TI Series Camera User Manual Chapter 5: Operation

3. Click UPLOAD FILE. The uploading process is started. On completion, the

RESTART button is valid.

4. Click to validate the Sarix TI Camera with the FM/SW uploading

process.

5.11.5 User Management Tab

The User Management tab is used to manage user’s login permissions.

Click System and select the User Management tab. The User Management tab opens:

Figure 5-68: System Window - User Management Tab

5-60

Chapter 5: Operation Sarix TI Series Camera User Manual

5.11.5.1 Adding a User

To add a new user:

1. Click . The following opens:

Figure 5-69: System Window - User Management Tab - Adding a User

2. Enter the User Name.

3. From the User Role drop-down list select the usage-level of the user:

4. Click to validate the changes.

5-61

5.11.5.2 Editing User Details

1. Select a user and click .

Figure 5-70: System Window - User Management Tab - Editing User Details

Sarix TI Series Camera User Manual Chapter 5: Operation

2. Change the user details.

3. Click to validate the changes.

5.12 Logging Out from the Web GUI

4. Stop any action, currently in process.

5. From the upper-right drop-down menu select Logout:

Figure 5-71: Logging Out from the Web GUI - Drop Down Menu

The user is logged out from the program and the Status window re-opens (see Figure 5-2).

5-62

Chapter 6: Maintenance Sarix TI Series Camera User Manual

6. Maintenance

This chapter provides the Sarix TI Series Camera preventive maintenance instructions.

The chapter consists of the following sections:

 Section 6.1: Visual Inspection
 Section 6.2: Cleaning

6.1 Visual Inspection

1. Visually inspect the camera and check the physical condition of the camera’s chassis and

lens.

2. Check the physical condition of the cable (torn, over-bending, damaged isolation, bent or

immersed pins).

6.2 Cleaning

Do not use any chemicals for cleaning the Sarix TI Camera. Failure

to comply could result in damage to the Sarix TI Camera optical-lens

and/or its surfaces.

1. Clean the Sarix TI Camera using wipes approved for optical equipment.

2. Clean any stains using a cotton-cloth, slightly dumped in tap water.

CAUTION

6-63

7. Ordering Information

This chapter provides information for purchasing the Sarix TI Series Camera and accessories.

The chapter consists of the following sections:

7.1 Ordering Information

Table 7-1: Ordering Information for 03 Hz Camera

Lens Type Part Number

17μ 640x480 14.2mm f/1.2, Athermalized, Fixed Focus TI2614

35mm f/1.2, Athermalized, Fixed Focus TI2635

50mm f/1.2, Athermalized, Fixed Focus TI2650

17μ 384x288 14.2mm f/1.2,Athermalized, Fixed Focus TI2314

35mm f/1.2,Athermalized, Fixed Focus TI2335

Sarix TI Series Camera User Manual Chapter 7: Ordering Information

50mm f/1.2,Athermalized, Fixed Focus TI2350

Table 7-2: Ordering Information for 9Hz Camera

Lens Type Part Number

17μ 640x480 14.2mm f/1.2, Athermalized, Fixed Focus TI2614-1

35mm f/1.2, Athermalized, Fixed Focus TI2635-1

50mm f/1.2, Athermalized, Fixed Focus TI2650-1

17μ 384x288 14.2mm f/1.2,Athermalized, Fixed Focus TI2314-1

35mm f/1.2,Athermalized, Fixed Focus TI2335-1

50mm f/1.2,Athermalized, Fixed Focus TI2350-1

7.2 Ordering Accessories

Table 7-3: Ordering Accessories

Part Number

Accessories:

SARIX TI POW cable 50 FT TICAB-P50

Wall Mount Accessories:

SARIX TI Wall Mount TIWM

SARIX TI Pole Adapter REQ Wall MNT TIPA

7-64

Chapter 8: Index Sarix TI Series Camera User Manual

8. Index

This chapter provides a list, arranged in alphabetical order, of keywords found throughout this
manual.

Streaming Window · 5-21

A

Abbreviations · 1-11

System Window · 5-51

GUI · 2-17

C

Certificates

Request · 5-19

Self-Signed Request · 5-19

Uploading a Certificate · 5-20

Cleaning · 6-63

D

Day Tab · 5-12, 5-25

Main Stream · 5-25

Secondary Stream · 5-27

Disable Camera · 5-13

E

Enable Camera · 5-14

F

Features · 2-14

I

Image Processing Window · 5-29

Day Tab · 5-37

Day Tab Geometry Settings · 5-38

Day Tab Misc Properties Settings · 5-39

Thermal Tab · 5-29

Thermal Tab Advanced Settings · 5-33

Thermal Tab Basic Settings · 5-30

Thermal Tab Color Processing Settings · 5-34

Thermal Tab Gain Control Settings · 5-32

Thermal Tab Signal Processing Settings · 5-31

Installation · 4-1

Camera Installation · 4-2

Unpacking · 4-1

Installing Camera · 4-2

IP PoE Cable · 4-6

Mechanical Interface Preparation · 4-2, 4-3

Pole Mount Configuration · 4-5

G

General Configuration Tab · 5-28

Getting Started

Changing Password · 5-5

Image Processing Window · 5-29

Live View Window · 5-7

Logging Into GUI · 5-3

Logging Out · 5-62

Main Window · 5-6

Network Window · 5-15

Status Window · 5-8

8-65

Wall Mount Configuration · 4-4

L

Live View Window · 5-7

LOF ·

Logging Out · 5-62

Login · 5-3

LOT · 1-7

1-7

M

Main Window Overview · 5-6

Sarix TI Series Camera User Manual Chapter 8: Index

Maintenance · 6-63

Cleaning · 6-63

Visual Inspection · 6-63

N

Network Window · 5-15

Certificates · 5-19

HTTPS Connection · 5-17

IP Address · 5-16

IP Address - Auto · 5-16

Manual DNS Server Address · 5-17

ONVIF Service · 5-18

Resetting Network Settings · 5-18

O

Operation · 5-1

Ordering Info · 7-64

Overview · 2-13, 2-14

Features · 2-14

GUI · 2-17

Physical Description · 2-15

Specifications · 2-18

Maintenance · 3-2

Scope · 1-12

Specifications · 2-18

CMOS Camera · 2-20

Configurations · 2-19

System Specifications · 2-18

Thermal Camera · 2-20

Status Window · 5-8

Status Window Overview

Day Tab · 5-12

Disable Camera · 5-13

Enable Camera · 5-14

System Tab · 5-9

Thermal Tab · 5-10

Streaming Window · 5-21

Day Tab · 5-25

General Configuration Tab · 5-28

Thermal Tab · 5-21

System Tab · 5-9

System Window · 5-51

Admin Tab · 5-51

Admin Tab - Archive System Files · 5-52

P

Password Change · 5-5

Physical Description · 2-15

R

Revisions · 1-1

S

Safety · 3-1

Safety Conventions · 3-1

Safety During Installation · 3-2

Safety During Maintenance · 3-2

Safety Instructions

Conventions · 3-1

Installation · 3-2

8-66

Admin Tab - Export Site · 5-54

Admin Tab - Factory Defaults · 5-55

Admin Tab - Restart · 5-51

Admin Tab - Save As Site · 5-53

Admin Tab - Site Defaults · 5-54

Date & Time Tab · 5-58

Date & Time Tab - Sync with Browser · 5-59

Date & Time Tab - Sync with NTP · 5-59

File Upload Tab · 5-60

Logs Tab · 5-57

User Management Tab · 5-60

User Management Tab - Adding a User · 5-61

User Management Tab - Editing a User · 5-62

T

Thermal Tab · 5-10, 5-21

Chapter 8: Index Sarix TI Series Camera User Manual

Main Stream · 5-22

Secondary Stream · 5-24

TOC · 1-2

U

Unpacking · 4-1

V

Visual Inspection · 6-63

8-67

Sarix TI Series Camera User Manual Chapter 8: Index

Pelco, Inc.

625 W. Alluvial Ave.

Fresno, CA 93711

Tel. [phone]

www.pelco.com

Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication
are trademarks of Pelco, Inc. or its affiliates. ONVIF and the ONVIF logo are trademarks of ONVIF Inc.

All other product names and services are the property of their respective companies.

Product specifications and availability are subject to change without notice.

© Copyright 2019, Pelco, Inc. All rights reserved.

8-68