Peerless Industries PARAMOUNT PF630 User Manual

Loading...

Installation and Assembly:

Paramount™ Flat Mount for 10" - 24" (25 - 61 cm) LCD Screens

Model: PF630

Features:

Screen held only .7" (18 mm) from wall for low-profile installation

Screen adapter plate simply slides into the wall plate for quick and easy installation

Colors: Gloss Black

Screen adapter plate included compatible with VESA 75 mm and 100 mm mounting patterns

Includes hardware for installation to wood studs, concrete, and cinder block

C U© L US

Max Load Capacity: 80 lb (36.3 kg)

ISSUED: 11-19-07 SHEET #: 202-9247-5 09-21-09

Note: Read entire instruction sheet before you start installation and assembly.

WARNING

Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor.

This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.

Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

Never exceed the Maximum Load Capacity. See page one.

If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an "edge to edge" stud finder is highly recommended.

Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.

This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.

This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION

HARDWARE REQUIRED

Wood Stud

Included

Wood Beam

Included

Solid Concrete

Included

Cinder Block

Included

Metal Stud

Do not attach except with Peerless Metal Stud Accessory Kit - ACC215;

Brick

Contact Qualified Professional

Other or unsure?

Contact Qualified Professional

Tools Needed for Assembly

stud finder ("edge to edge" stud finder is recommended)

phillips screwdriver

drill

• 5/16" (8 mm) bit for concrete and cinder block wall

• 5/32" (4 mm) bit for wood stud wall

level

Table of Contents

Parts List.................................................................................................................................................................................

3

Installation to Single Wood Stud Wall.....................................................................................................................................

4

Installation to Solid Concrete or Cinder Block.........................................................................................................................

5

Attaching Mounting Plate to Screen with VESA Mounting Patterns........................................................................................

6

Installing and Removing Flat Panel Screen............................................................................................................................

7

2 of 24

ISSUED: 11-19-07 SHEET #: 202-9247-5 09-21-09

Before you begin, make sure all parts shown are included with your product.

Parts may appear slightly different than illustrated.

Parts List

 

 

Description

Qty.

PF630

 

 

Part #

 

 

 

 

A

wall plate

1

095-P1496

 

B

hook plate

1

095-P1497

 

C

M5 x 12 mm phillips screw

2

520-1027

 

D

#14 x 2.5" wood screw

2

5S1-015-C03

 

E

concrete anchor

2

590-0320

 

F

M4 x 10 mm phillips screw

4

504-9012

 

G

M4 x 20 mm phillips screw

4

504-9020

 

H

retaining spacer

4

590-5005

A B

C D E F G H

3 of 24

ISSUED: 11-19-07 SHEET #: 202-9247-5 09-21-09

Installation to Single Wood Stud Wall

WARNING

Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.

Never tighten in excess of 80 in. • lb (9 N.M.).

Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended.

Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).

Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended.

1 Based on its edges, draw a vertical line down the stud’s center. Place wall plate (A) on wall as a template, making sure that the two mounting holes are on the stud centerline. Level wall plate, and mark the center of the two holes. Drill two 5/32" (4 mm) dia. holes 2.5" (64 mm) deep. Make sure that the wall plate is level, secure it using two #14 x 2.5" wood screws (D) as shown.

Skip to step 2

WOOD STUD

A

D

4 of 24

ISSUED: 11-19-07 SHEET #: 202-9247-5 09-21-09

Peerless Industries PARAMOUNT PF630 User Manual

Installation to Solid Concrete or Cinder Block

WARNING

When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware and components.

1

Make sure that wall plate (A) is level, use it as a

template to mark two mounting holes. Drill two 5/16"

(8 mm) dia. holes to a minimum depth of 2.5"

(64 mm). Insert anchors (E) in holes flush with wall as shown. Place wall plate over anchors and secure with two #14 x 2.5" screws (D). Level, then tighten all fasteners.

WARNING

Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power.

Never tighten in excess of 80 in. • lb (9 N.M.).

Always attach concrete expansion anchors directly to load-bearing concrete.

Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable, the finishing surface must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8" (16 mm), custom fasteners must be supplied by installer (not evaluated by UL).

VIEW

 

INCORRECT

CORRECT

wall

concrete

wall

concrete

 

 

 

plate

 

 

plate

 

 

CUTAWAY

 

 

 

 

drywall

 

drywall

 

 

plaster/

 

plaster/

1

concrete

surface

E

Drill holes and insert anchors (E).

2

A

 

 

D

E

Place plate (A) over anchors (E) and secure with screws (D).

3

Tighten all fasteners.

solid

concrete

cinder block

E

A

D

5 of 24

ISSUED: 11-19-07 SHEET #: 202-9247-5 09-21-09

Attaching Mounting Plate to Screen Using

VESA 50, 75 or 100 mm Mounting Pattern

WARNING

If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.

2 For VESA® 50, 75 or 100 Mounting Pattern:

Choose hole pattern as shown in detail 1 for VESA 50, 75 or 100 mounting pattern. Attach hook plate (B) to back of screen using four M4 x 10 mm screws (F) as shown.

NOTE: Be certain bottom flanges of hook plate (B) face toward bottom of screen.

*NOTE: If hole pattern is in a pocket, attach hook

plate (B) to back of screen using four M4 x 20 mm B screws (G) and four retaining spacers (H) as indicated.

Skip to step 5.

F or G

Bottom Flanges

screen

*For screens with a hole pat-

 

tern in a pocket, spacers (H)

 

go between hook plate (B) and

H

screen when using screw (G).

Mounting Patterns

VESA® 50

VESA® 75

VESA® 100

 

 

 

DETAIL 1

6 of 24

ISSUED: 11-19-07 SHEET #: 202-9247-5 09-21-09

Installing and Removing Flat Panel Screen

WARNING

Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the screen.

5

Attach hook plate (B) to wall plate (A) by sliding flanges of hook plate (B) into hook flanges of wall plate (A). Secure

hook plate to wall plate using two M5 x 12 mm phillips screws (C) through bottom flanges of wall plate (A) and into

 

bottom flanges of hook plate (B) as shown. Tighten screws securely.

 

To remove screen from mount, remove screws (C) and lift screen off of mount.

CAUTION

• Do not tighten screws with excessive force. Overtightening can cause damage to mount.

B

B

Flanges

A

A

C

Hook

Flanges

7 of 24

ISSUED: 11-19-07 SHEET #: 202-9247-5 09-21-09

© 2009, Peerless Industries, Inc. All rights reserved. All other brand and product names are trademarks or registered trademarks of their respective owners.

Peerless Industries, Inc.

3215 W. North Ave. Melrose Park, IL 60160 www.peerlessmounts.com

Instalación y ensamblaje:

Soporte de pared plano Paramount™ para pantallas LCD de 10" a 24" (25 a 61 cm)

Modelo: PF630

Características:

Sostiene el televisor a sólo .7" (18 mm) de la pared para proporcionar una instalación discreta

La placa adaptadora de la pantalla sencillamente se desliza sobre la placa de pared para proporcionar una instalación rápida y fácil

Colores: Negro lustroso

Incluye la placa adaptadora para la pantalla compatible con las configuraciones de montaje de VESA 75 mm y 100 mm

Incluye los accesorios para instalaciones en montantes de madera, concreto y bloques de hormigón de escorias

C U© L US

Capacidad máxima de soportar carga: 80 lb (36.3 kg)

PUBLICADO: 11-19-07 HOJA #: 202-9247-5 09-21-09

+ 16 hidden pages