Peavey VSX 26, 48, VR112 User Manual

Setting up the

Versarray System

Processor Settings for Versarray 112Neo & Subs

(also Digitool/Prolinx)

Single VR112 Neo Cabinet w/118 Sub

Front End EQ (before the crossover section) = PEQ –2.0 dB @ 2k, bw= 0.6 (or use
1/3 octave band at 2 kHz set to –2.0 dB);

Infrasonic filtering: 24 dB/oct. LR @ 34 Hz)
Crossover settings:
Woofer= 24 dB/oct. LR @ 2.0 kHz, Tweeter= 24 dB/oct. Bessel @ 3.0 kHz, Woofer

Polarity Normal, Tweeter Polarity Normal
Sub to Woofer Crossover: Sub= 24 dB/oct. LR @ 125Hz, Woofer= 24 dB/oct LR @

100Hz, Sub Polarity Normal, Woofer Polarity Normal

EQ after crossover:

Woofer EQ = PEQ +1.5 dB @ 560 Hz, bw=0.5; PEQ -3.5 dB @ 850 Hz, bw=0.5
PEQ +3dB @ 115 Hz, bw= 2; PEQ –1.5 dB @ 2.2 kHz, bw=.7;
PEQ –2 dB @ 700 Hz, bw=3.0 Woofer Delay = 0.0 ms (none)

Tweeter EQ: PEQ –3 dB @ 2.7 kHz, bw= 0.7; PEQ +2.5 dB @ 4.6 kHz, bw= 1.0;
PEQ +3.5 dB @ 16.5 kHz, bw=1.0 Tweeter Delay = 0.0 ms (none)

Sub EQ: PEQ +4.0 dB @ 50 Hz, bw= 0.7; PEQ -2.5 dB @ 100 Hz, bw= 0.5

with VSX 26/48

Chart for Changes with Number of Cabinets

No. of Cabs: 1 2 3 4 6 8
218 Sub

Level†: -6.0 dB -2.5 dB -0.5 dB +1.5 dB +4 dB +5.5 dB
12” Wfr 0.0 dB 0.0 dB 0.0 dB 0.0 dB 0.0 dB 0.0 dB

Level:
Twtr 0.0 dB +2.0 dB +4.0 dB +5.5dB +6.5 dB +7.0 dB

Level:
(Drive levels are for factory 16 ohm wiring, for 4 ohm wiring, subtract 6 dB)

Front Block EQ‡
at 2 kHz -2.0 dB - - - - -

at 1.8 kHz - -3.0 dB -3.5 dB -3.5 dB -4.0 dB -4.5 dB
(at a bw set to 0.577) bw=.707 bw=.707

† SPECIAL NOTE: Versarray™ 218 Sub is supplied in 4 ohm mode (woofers
paralleled).
If the Versarray™ 218 Sub woofers are driven separately, using an amp with the
same gain as all the other amps, then drive level to the separate woofers is the
same.

To convert the above drive levels for a single Versarray™ 218 Sub to drive levels
suitable for a single Versarray™ 118 Sub, add 6 dB.

When doubling the number of Subs, subtract 6 dB for each time they are doubled.

‡ SPECIAL NOTE: To match this PEQ setting with a 1/3 octave band EQ, use the
following:

To equate to a PEQ setting of –3 dB @ 1.8k, bw= 0.6 use, 1/3 octave band 2 kHz set
to –1.5 dB AND 1/3 octave band 1.6 kHz also set to –1.5 dB

To equate to a PEQ setting of –3.5 dB @ 1.8k, bw= 0.6, use 1/3 octave band 2 kHz
set to –2 dB AND 1/3 octave band 1.6 kHz set to –1.5 dB

To equate to a PEQ setting of –4 dB @ 1.8k, bw= 0.7 (or use 1/3 octave band 2 kHz
set to –2.0 dB AND 1/3 octave band 1.6 kHz set to –2.0 dB

To equate to a PEQ setting of –4.5 dB @ 1.8k, bw= 0.7 (or use 1/3 octave band 2
kHz set to –2.5 dB AND 1/3 octave band 1.6 kHz set to –2.0 dB