Parkside KH 3028 RANDOM ORBITAL SANDER, XQ 270 - MANUEL 2, XQ 270 Operation And Safety Notes
XQ270
RANDOM ORBITAL SANDER
Operation and Safety Notes
Translation of original operation manual
EXZENTERSCHLEIFER
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
GB / IE / CY Operation and Safety Notes Page 5
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 13
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the
device.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
DC
BA
6 7 8
2
5 4
3
1
5 GB/IE/CY
Introduction
Intended utilisation ........................................................................................................Page 6
Features and Fittings .....................................................................................................Page 6
Items supplied ................................................................................................................Page 6
Technical data ...............................................................................................................Page 7
General safety advice for electrical power tools
1. Workplace safety .....................................................................................................Page 7
2.
Electrical safety .........................................................................................................Page 7
3. Personal safety ..........................................................................................................Page 8
4.
Careful handling and use of electrical power tools ................................................Page 8
Safety advice relating specifically to random orbital sanders ...................................Page 9
Original accessories / tools ..........................................................................................Page 10
Before use
Selecting the Grinding Disc ..........................................................................................Page 10
Changing sanding sheets .............................................................................................Page 10
Dust / Swarf Removal by Suction ...............................................................................Page 10
Commissioning
Switching on and off .....................................................................................................Page 11
Working instructions
Grinding Surfaces .........................................................................................................Page 11
Maintenance and Cleaning ........................................................................Page 11
Service centre .......................................................................................................Page 11
Warranty ...................................................................................................................Page 11
Disposal ......................................................................................................................Page 12
Declaration of Conformity / Manufacturer ...................................Page 12
Table of contents
6 GB/IE/CY
Random orbital sander XQ270
Introduction
Please make sure you familiarise yourself
fully with the way the device works before
you use it for the first time and that you
understand how to handle electrical power tools
correctly. Further details can be found in the operating
instructions. Keep these instructions in a safe place. If
you pass the device on to anyone else, please ensure
that you also pass on all the documentation.
Intended utilisation
The appliance is suitable for the dry sanding and
buffing of wood, metal and paint. Any other uses,
and modifications to the appliance, are deemed to
be improper usage and may result in serious physical injury. The manufacturer will not accept liability
for loss or damage arising from improper use.
This appliance is not intended for commercial applications.
Features and Fittings
1
ON / OFF switch
2
Locking button
3
Dust collector
4
Backing pad
5
Grinding disc
6
Exhaust nozzle
7
Adapter for external exhaust suction
8
Reducing piece
Items supplied
1 random orbital sander XQ270
1 dust collector
1 grinding disc
1 adapter for external exhaust suction
1 reducing piece
1 set of operating instructions
Introduction
The following pictograms are used in these operating instructions / on the device:
Read instruction manual! Safety class II
Observe caution and safety notes! Proper procedure and handling.
Caution – electric shock!
Danger to life!
Wear hearing protection, dust
protection mask, protective glasses
and protective gloves.
Risk of explosion!
Keep children away from electrical
power tools!
V
~
Volt (AC) For indoor use only!
W
Watts (effective power)
Risk of loss of life by electric shock from
damaged mains lead or mains plug!
n
0
Rated idle running speed
Dispose packaging and appliance in
an environmentally-friendly way!
7 GB/IE/CY
Technical data
Rated voltage: 230 V~ 50 Hz
Rated power: 270 W
Idling oscillation frequency: n
0
24000 min
-1
Idling speed: n0 12000 min
-1
Sanding plate: ø 125 mm
Protection class: II /
Noise and vibration data:
Measured values for noise are determined in accordance with EN 60745. The A-weighted noise
level of the electrical power tool are typically:
Sound pressure level: 83 dB(A)
Sound power level: 94 dB(A)
Uncertainty K: 3 dB
Wear ear protection!
Vibration total values determined according to
EN 60745:
Vibration emission value a
h
= 5 m / s2,
Uncertainty K < 1.5 m / s
2
.
WARNING!
The vibration level given in these
instructions has been measured in accordance with a
standardised measurement procedure specified in
EN 60745 and can be used to compare devices.
Different uses of the device give rise to different vibration levels and in many cases they may exceed the
values given in these instructions. It is easy to underestimate the vibration load if the electrical power tool is
used regularly in particular circumstances.
Note: If you wish to make an accurate assessment
of the vibration loads experienced during a particular period of working, you should also take into account the intervening periods of time when the device is switched off or is running but is not actually
in use. This can result in a much lower vibration
load over the whole of the period of working.
General safety advice
for electrical power tools
WARNING!
Read all the safety advice
and instructions! Failure to observe the safety
advice and instructions may result in electric shock,
fire and / or serious injury.
KEEP ALL THE SAFETY ADVICE AND INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE! THE TERM “ELECTRICAL TOOL” USED
IN THE SAFETY ADVICE REFERS TO ELECTRICAL
TOOLS POWERED BY MAINS ELECTRICITY (BY
MEANS OF A MAINS LEAD) AND ELECTRICAL
TOOLS POWERED BY RECHARGEABLE BATTERIES (WITHOUT A MAINS LEAD).
1. Workplace safety
a) Keep your working area clean and
well lit. Untidy or poorly lit working areas
can lead to accidents.
b)
Do not work with the device
in potentially explosive environments in which there
are inflammable liquids, gases or
dusts. Electrical power tools create sparks,
which can ignite dusts or fumes.
c)
Keep children and other peo-
ple away while you are operating the electrical tool.
Distractions can cause you to lose control of
the device.
2. Electrical safety
To avoid danger to
life from electric shock:
a)
The mains plug on the device must match
the mains socket. The plug must not
be modified in any way. Do not use
an adapter plug with devices fitted
with a protective earth. Unmodified
plugs and matching sockets reduce the risk of
electric shock.
Introduction / General safety advice for electrical power tools
8 GB/IE/CY
b) Avoid touching earthed surfaces such
as pipes, radiators, ovens and refrigerators with any part of your body.
There is an increased risk of electric shock if
your body is earthed
.
c) Keep the device away from rain or
moisture. Water entering an electrical device
increases the risk of electric shock.
d)
Do not use the mains lead for
any purpose for which it was
not intended, e.g. to carry the
device, to hang up the device or to pull
the mains plug out of the mains socket.
Keep the mains lead away from heat,
oil, sharp edges or moving parts of the
device. Damaged or tangled mains leads
increase the risk of electric shock.
e) When working outdoors with an elec-
trical power tool always use extension
cables that are also approved for use
outdoors. The use of an extension cable suitable
for outdoor use reduces the risk of electric shock.
f) Use a residual current device (RCD)
for protection if operating the electrical
power tool in a moist environment is
unavoidable. The use of an RCD reduces
the risk of electric shock.
3. Personal safety
a) Remain alert at all times, watch what
you are doing and always proceed
with caution. Do not use the device if
you are tired or under the influence
of drugs, alcohol or medication. One
moment of carelessness when using the device
can lead to serious injury.
b)
Wear personal protective
equipment and always wear
safety glasses. The wearing of
personal protective equipment such as dust
masks, non-slip safety shoes, safety helmets or
ear protectors, appropriate to the type of electrical power tool used and work undertaken,
reduces the risk of injury.
c) Avoid unintentional operation of the
device. Check that the electrical pow-
er tool is switched off before you connect it to the mains, pick it up or carry
it. Accidents can happen if you carry the de-
vice with your finger on the ON / OFF switch or
with the device switched on.
d) Remove any setting tools or spanners
before you switch the device on. A tool
or spanner left attached to a rotating part of a
device can lead to injury.
e) Avoid placing your body in an unnat-
ural position. Keep proper footing
and balance at all times. By doing this
you will be in a better position to control the
device in unforeseen circumstances.
f) Wear suitable clothing. Do not wear
loose clothing or jewellery. Keep your
hair, clothing and gloves clear of moving parts. Loose clothing, jewellery or long
hair can become trapped in moving parts.
g) If vacuum dust extraction and collection
devices are fitted do not forget to
check
that they are properly connected
and
correctly used. The use of these devices re-
duces the hazard presented by dust.
4. Careful handling and use of
electrical power tools
a) Do not overload the device. Always
use an electrical power tool that is
intended for the task you are undertaking. By using the right electrical power
tool for the job you will work more safely and
achieve a better result.
b) Do not use an electrical power tool if
its switch is defective. An electrical power
tool that can no longer be switched on and off
is dangerous and must be repaired.
c) Pull the mains plug out of the socket
before you make any adjustments to
the device, change accessories or when
the device is put away. This precaution is
intended to prevent you from unintentionally
starting the device.
d) When not in use always ensure that
electrical power tools are kept out of
reach of children. Do not let anyone
General safety advice for electrical power tools
Loading...