Paradox NV780MR Installation Manual

NV780MR

Screw Holes x6

Dip Switch

Wire Entry

Jumper

(see Table 1)

0

0°

20°

12m
40 ft

3m

10 ft

3m

10 ft

12m
40 ft

0°

20°

3m

0°

3°

60 cm

012m

40 ft

12m
40 ft

30 cm (12 in.)

Installation Manual V1.0

Wireless Dual Side-View

Anti-Mask Outdoor

Detector

General Description

The NV780MR is a wireless dual, independent, side-by-side view

Passive Infrared (PIR) motion detector with dual anti-mask in a
single housing, providing boundary protection. Covering
approximately 24m / 78 ft. (12m / 39 ft. on each side) and
configurable to report either as a single unit with two sides
reporting as a single zone output or as a dual unit with each side
reporting as a separate zone input.

Installing the NV780MR

Dip Switch Settings

Table 1

DIP SWITCH OFF ON (DEFAULT)

1. RF MHz 868 433

2. BUZZER OFF ON

3. SENSITIVITY LOW HIGH

4. ZONE DUAL SINGLE

JUMPER: LED OFF ON

Power-Up Sequence Indication

• LED: Both left and right LEDs blink red for five seconds.

• Buzzer Switch ON:

• Single Mode: One tone beeping for five seconds.

• Dual mode: Alternate tone beeping for five seconds.

• Anti-mask calibration can take up to 40 seconds, red / green
flashing if Buzzer is ON; three beeps indicates completion.

Alarm

• LED: Red LED indication on the relevant side(s) for three
seconds.

• Buzzer Switch ON:

• Single Mode: Same tone for either side detection.

• Dual mode: Each side has its own tone.

Figure 1 : Front View - Open Cover

Minimum Recommended Installation Distance: At least 40 cm/

15.7 in. from the protected area (door, window, etc.)

Anti-Mask Calibration

The anti-mask will only calibrate after the tamper is closed. The
NV780MR performs anti-mask calibration for up to 40 seconds,
indicated by flashing red / green LEDs until completed. On
completion, the LEDs shut off. If the buzzer is set to ON, three
beeps signal that calibration is complete.
IMPORTANT: During calibration, no objects should be within 2m /
6 ft. of the anti-mask field of view (on both sides of the detector).

Anti-Mask Detection

• LED: Flashes orange rapidly (pre-alarm state) and then

flashes when in alarm.

• If Buzzer is ON: buzzer beeps for 3 seconds.

NOTE: The anti-mask relay is open during anti-mask detection.

Beam Patterns

Beam Range Adjustment

Horizontal Beam Adjustment

Anti-Mask

Adjusting the Beam Range

Slide Up
or Down
for Range

Pull Out for 0°
(Parallel Beam to Wall)

Push in for 3°
(Beam 3° from Wall)

Adjust the beam range by shifting the lower lens up and down:.
Hold the cover in the UP position and slide the plastic tab in the
lower lens up or down on the side you wish to adjust, until the
module is aligned in the desired position. Align the top of the tab
with the required angle of the beam (Figure 2):

0° = 12m
5°= 10.5m
10° = 7.5m
15° = 5.25m
20° = 3m

Once adjusted, lock into place by pushing the tab into the slot.

Adjusting the Horizontal Beam

Beams (on either side of the module) are projected parallel to the

wall (default). The beams can be adjusted to project 3
from the wall, distancing the beam 60 cm / 24 in. from the wall in
order to avoid detection of unwanted objects next to the module
(Figure 2).

To adjust the beams in relation to the wall, identify the side
needing adjustment, and slide the lens tray in or out of the detector
to the required position:

0° - Slide the lens tray until it is flush with the top edge of the lens

holder.

3° - Slide the lens tray until it is flush with the bottom edge of the

lens holder.

0

horizontally

Technical Specifications

Sensor 4x dual low noise rectangular elements

Lens

Processing

Startup Time 25 seconds

Detection Speed 0.2m / sec.– 4m/sec. (0.6 ft/sec.– 13.1 ft /sec.)

Power Input 4.5Vdc = 3 x1.5VDC AA Alkaline batteries

Battery life 3 years (LED and Buzzer off)

Low Battery 3.4V

Coverage

PET Immunity

Anti- Mask

Alarm Indicator 2x red LED for 3 seconds + buzzer

Anti-Tamper
Switch

Operating
Temperature

Outdoor
protection

Humidity 95% max.

RF Frequency

RF Immunity

Compatibility RTX3 and Magellan systems

Dimensions

Weight 450 gr/ 0.99 lb. (with batteries)

Certifications

2nd gen., flat, 2x dual beam, 1.7” focal point,
narrow beam long-range Fresnel lens

Digital APSP / Digital temperature
compensation

Bi-directional, independent, 2 x 3m to 12m
(10 ft. to 39 ft.) at 1.5m / 4.9 ft. height

Up to 40 kg (90 lb) - minimum 1.5m / 4.9 ft
installation height

Active IR detection for blocking 10 cm up to
30 cm and sprayed liquid

N.C. 28 Vdc, 0.15A

-35°C to +50°C / -31°F to +122°F

IP54

Dual Band: 433.92 MHz/ 868.35 MHz

IMPORTANT: For US and Canada, only

433.92 MHz is used

Complies with EN 50130-4: 10V / m 80 MHz
to 2.7 GHz

L 8.35 in. x W 4.46 in. x D 2.7 in.
(21.2 cm x 1.21 cm x 6.8 cm)

EN 50131-2-2, Security Grade 2,
EN 50130-5 Environmental Class IVA
EN 50131-6 Type C

Figure 2 : Beam Adjustment

Warranty: For complete warranty information on this product please refer
to the Limited Warranty Statement found on the website:
www.paradox.com/terms or contact your local distributor. © 2016 Paradox
Security Systems (Bahamas) Ltd. All rights reserved. Specifications may
change without prior notice.

Patents: One or more of the following US patents may apply: 7046142,
6215399, 6111256, 6104319, 5920259, 5886632, 5721542, 5287111, and
RE39406 and other pending patents may apply. Canadian and
international patents may also apply.

NV780MR-EI00 03/2016