for each step to insure proper
assembly of thi,,; product.
1Revision: 12/4/00
]IMPORTANT NOTES]
Please note:
* Thank you for purchasing the Parabody 100101 LEG PRESS. Please read these instructions
thoroughly and keep them for future reference. This product must be assembled on a flat,
level surface to assure its proper function.
We recommend cleaning your product (pads and flame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased flom your Parabody customer service representative
at (800) 328-9714.
There is a risk assumed by individuals who use this type of equipment. To minirnize risk, please
follow these rules:
1. Inspect equipment daily. Tighten all loose connections and replace worn p~:ts immediately.
Failure to do so may result in serious injury.
2. Do not allow minors or children to play on or around this equipment.
3. Exercise with care to avoid injury.
4. If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at (800) 328-9714.
5. Consult a physician before beginning any exercise program.
[ Tools Required for Assembly ]
* 3/4" wrench
* 9/16" wrench
* Ratchet with 3/4" and 9/16" sockets
* Adjustable wrench
* 5/32" Mien wrench
* Tape measure
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH RULER:
I
1/2]
1/2]
BOLT LENGTH I
1/2 ] 1/2 [ 1/2 ] 1/2 ]
2
3 4 5 6
2
PARTS LIST
!KEY
10
11
12
13
14
15
16
17
PART #
1
6574508BASE FRAME
2
6573608SEATFRAME
3
6575008
4
6575408FOOT PLATE
5
6573908
6
6476408
7
6575102
8
6597421
9
65740013/4 X 8-1/4" SHAFT
3103102
31162013-1/2" PULLEY
61770012-1/2 X 5-1/2" NON-SKID STRIP
64052012" SQ. END CAP
6416601
6467001
65006012" WHEEL
3102501
DESCRIPTION
REAR TUBE
LEVER TUBE
HANDLE
ADJUSTMENT TUBE
SEAT PAD
1X8" GRIP
PARAGLIDE (QTY. 8)
2" SQ. COVER CAP
3/8" FLAT WASHER
QTYKEY
1
, 119
1
1
222
1
124
2
226
2
128
829
1430
1
232
233
8
18
20
21
23
25
27
31
PART #
31026013/8" LOCK WASHER
3102802
3102807
3102801
3102804
3102941
31029223/8 X 2-3/4" BOLT
3102904
31029353/8 X 4-1/2" BOLT
3102918
3202107
6122703
6020601
3104901
3106803
64120013/8" SPRIN~ 3 PIN
3/8" LOW HEIGH’ LOCK NUT
1/2" LOW HEIGHT LOCK NUT
DESCRIP 3N
3/8" LOC) NUT
1/2" LOCI{ NUT
3/8 X 1-1/2" BOLT
3/8 X 3" BOLT
1/2 X 3-1/4" BOLT
1/2 X 6-1/2" BOLT
3/8 ID X 3/8" SPACER
1/2" FLANGE BEARING
3/4" FLANGE BEARING
5/16" SET SCREW
QT¥
4
2
1
2
2
2
2
2
1
2
2
2
8
4
4
1
3
3/8
FIGURE 1
STEP 1:
¯ Attach two 2" SQ. COVER CAPS (15) onto the ends &the REAR TUBE (3) as shown in FIGURE
¯ Insert four 2" SQ. ENDCAPS (13) into the ends of the BASE FRAME (1) as shown in FIGURE
SECURELY assemble the REAR TUBE (3) to the BASE FRAME (1) using two 3/8 X 3" BOLTS (25), 278" FLAT WASHERS
(17), and two 3/8" LOCK NUTS (19). See FIGURE
]1/2
0
I
1234
1/2
I
1/2[ I/2[1/2[
4
1/:!
5
I
6
I
/
/
FIGURE 2
STEP 2:
¯
Insert two 2" SQ. ENDCAPS (13) into file ends of the SEAT FRAME (2) as shown in FIGURE
¯
SECURELY assemble one 3/8" SPRING PIN (33) to the spring pin barrel on the SEAT FRAME (2) as shown in FIGURE
¯
Attach four PARAGLIDE STRIPS (14) to the inside of the SEAT FRA~£E (2) using file following steps:
¯
Thoroughly clean all surfaces where the PARAGLIDE STRIPS (14) are to be attached.
¯
l~emove the PARAGLIDE STRIPS (14) from the paper backing and firmly apply them to all shown surfaces.
5
3/8" LOW HEIGHT
/
FIGURE 3
STEP 3:
¯
SECURELY assemble one 3-1/2" PULLEY (11), two 2" WHEELS (16), two 3/8" FLAT WASHERS (17):. and two 3/8 ID
SPACERS (29) to the ADJUSTMENT TUBE (7) using one 3/8 X 4-1/2" BOLT (26) as shown in FIGURE
¯ Attach four PARAGLIDE STRIPS (14) to the outside of the ADJUSTMENT TUBE (7) using the followirtg steps:
¯
Thoroughly clean all surfaces where the PARAGLtDE STRIPS (14) are to be attached.
¯
Remove the PARAGLIDE STRIPS (t4) from the paper backing and firmly apply them to all shown surfaces.
1/2 I 1/2 I 1/2 I 1/2 I 1/2 I 1/2 I
3 4 5 6
PIN
FIGURE 4
STEP 4:
¯ CAREFULLE¥ slide the ADJUSTMENT TUBE (7) over into the SEAT FRAME (2) and engage the SPRING PIN into one
the adjustment holes. See FIGURE 4.
STEP 5:
¯
Insert two 3/4" FLANGE BEARINGS into
each of the two LEVER TUBES (5)
shown in FIGURE 5.
FIGURE 5
5/16" SET SCREW~
FIGURE 6
STEP 6:
¯ Insert four 2" SQ. END CAPS (13) into the ends of two LEVER TUBES (5) as shown in FIGURE
SECURELY assemble the LEVER TUBES (5) to the BASE FRAME (1) using two 3/4" SHAFTS (9) and. SECURE in
¯
using four 5/16" SET SCREWS (32). See FIGURE
1/2
I
1/2I
1/2I
2
II I
1/2
I
[
4
1/2
I
6
FIGURE 7
STEP 7:
¯ Insert four 2" SQ. END CAPS (13) into the ends of FOOT PLATE (4) as shown in FIGURE
¯ Insert eight 1/2" FLANGE BEARING (30) into the LEVER TUBES (5) as shown in FIGURE
1/2" LOW HEIGHT @~’""
FIGURE 8
STEP 8:
¯ SECURELY assemble the FOOT PLATE (4) to the LEVER TUBES (5) using two 1/2 X 6-1/2" BOLTS (28) and two 1/2"
HEIGHT LOCK NUTS (22) as shown in FIGURE
¯ CAREFULLY attach eight NON-SKID STRIPS (12) to the FOOT PLATE (4) as shown in FIGURE
3-1/4"
FIGURE 9
STEP 9:
¯ SECURELY assemble the SEAT FRAME (2) to the LEVER TUBES (5) using two 1/2 X 3-1/4" BOLTS (27) and two 1/2"
NUTS (21) as shown in FIGURE
11
/
/
!
I
I
/
/
/
I
I
I
I
I
I
I
I
i
I
I
I
I
~
~
3/8 X 1-1/2"~
FIGURE 10
/
/
/
I
I
I
/
/
1
I
I
I
/
/
/
STEP 10:
¯
SECURELY assemble the SEAT PAD (8) to the HANDLE (6) and the SEAT FRAME (2) using two 3/8 X 1-1/2" BOLTS
two 3/8" LOCK WASHERS (18), and two 3/8" FLAT WASHERS (17). See FIGURE
1/2[
] I 1
112[
1
I I 1
I
2
1/2 [ 1/2
[ I I I
I
12
6
X 2-3/4~/
FIGURE 11
STEP 11:
¯ SECURELY assemble the SEAT PAD (8) to the SEAT FRAME (2) using two 3/8 X 2-3/4" BOLTS (24) and two 3/8"
WASHERS (18) as shown in FIGURE 11.
¯ Slide two 1 X 8" GRIPS (10) over each HANDLE (6) as shown in FIGURE
13
FIGURE 12
STEP 12:
¯ To adjust the SEAT, sit in the LEG PRESS, gently press against the FOOT PLATE and pull back on the SPRING PiN.
¯ Refer to the LEG PRESS ADAPTOR assembly instructions to attach the 832102 LEG PRESS to the home gym.
Thank you for purchasing the Parabody 100101 LEG PRESS. If unsure of proper use of equipment, call
your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
I
1/2
0
I I1 II
I
I
112
1
I
2
I I I
1/2
I I II
I
I
3
<14
1/2 I 1/2I
I I I I
3;/2 I
6
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.