ParaBody Hip Sled System User Manual

835 HIP SLED SYSTEM

WARNING:

Read and follow all directions
for each step to insure proper
assembly of this product.

CLASS H
PART # 7339501
REV . B

USER’S GUIDE

1

Version: 835109

Revision: 12/09/02

j

TABLE OF CONTENTS

Safety Statement.............2

General Notes..................3

Tools Required................3

Gym Layout.....................4

Parts list..........................5

Assembly Instructions.....6-21

General Maintenance.......22

W arranty Statement..........23

Product Services..............24

Insert-Registration Card

IMPORTANT SAFETY INFORMATION

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF

EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!

1. Before using, read all the warnings and instructions
on the use of this machine. Use only for intended
exercise. DO NOT modify the machine.

2. Obtain a medical exam before beginning any
exercise program.

3. Keep body and clothing free of all moving objects.

4. Inspect the machine before use. DO NOT use it if it
appears damaged. DO NOT attempt to fix a broken or

ammed machine. Notify your authorized ParaBody
dealer before use and have repairs made by an
authorized service technician.

6. Never pin the weights or prop plate into an elevated
position. DO NOT use the machine if found in this
condition. DO NOT attempt to fix. Notify your
authorized ParaBody dealer.

7. Inspect cables and their connections before using
machine. Pay particular attention to the cable ends.
DO NOT attempt to fix. Notify your authorized
ParaBody dealer before use and have repairs made by
an authorized service technician.

8. Make sure all spring loaded pull pins are fully
engaged in the adjustment position and fully tighten
thumbscrew before use.

5. Be certain that weight pin is completely inserted.
Use only the pin provided by the manufacturer. If
unsure, call your authorized ParaBody dealer.

9. Children must not be allowed near this machine.
Supervise teenagers.

.

NOTE: In a continual effort to improve our products, specifications are subject to change
2002 Life Fitness, a division of Brunswick Corporation. All rights reserved.

©

ParaBody is a trademark of Brunswick Corporation

www.parabody.com

2

IMPORTANT NOTES

Please note:

* Thank you for purchasing the ParaBody 835 Hip Sled System. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.

* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.

T ools Required for Assembly

* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* T ape measure

Bolt Length Ruler

NOTE: BOL T LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.

BOLT LENGTH

BOL T LENGTH RULER:

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

3

6

1’

2’

3’

4’

1’ 2’

3’ 4’ 5’

7’

8’

9’

5’

6’

1 Square = 1’ X 1’

4

PARTS LIST

Hardware bags:

Bag 1= LEA7078609 Bag 2= LEA7078709

Bag 3= LEA7078809

KEY

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

PART #

LEA6504909
LEA6506809
LEA7337609
LEA6507709
LEA6507809
LEA6667809
LEA6505910
LEA7337309
LEA7337409
LEA6504410
LEA7337710
LEA6506610
LEA6507010
LEA6521210
LEA6534310
LEA6667910
LEA6509221
LEA6666921
LEA6667321
LEA6500501
LEA6500601
LEA3103101
LEA3103104
LEA3116001

DESCRIPTION

BASE

PLA TFORM SLEEVE

PAD SUPPOR T

RIGHT HANDLE

LEFT HANDLE
REAR UPRIGHT

CARRIAGE STOP BAR

LEFT RAIL

RIGHT RAIL

FOOT PLA TE

PLA TFORM

PLA TFORM ADJUSTMENT

WEIGHT SUPPORT

ADJ. WHEEL BRACKET

P AD STOP

CARRIAGE

SHOULDER P AD

SEA T P A D

BACK P AD
3” DIA. WHEEL
2” DIA. WHEEL

1-1/4 X 5” GRIP

1 X 5” GRIP

1-1/4” SQ. RUBBER BUMPER

QTY

1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
2
1
1
4
4
2
2
2

KEY

25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47

PART #

LEA6270501
LEA6405201
LEA6416601
LEA7234801
LEA3114403
LEA3114502
LEA3114702
LEA3114401
LEA3114701
LEA3235501
LEA3235204
LEA3235208
LEA3235212
LEA3235218
LEA3235405
LEA3235311
LEA3235313
LEA3235316
LEA3235318
LEA3235320
LEA3110002
LEA6020601
LEA6466901

DESCRIPTION

4 X 14” NON-SKID STRIP

2” SQ. END CAP

1-1/2” X 3/4” PARAGLIDE

2” SQ. COVER CAP

3/8” WASHER

3/8” LOCK WASHER

3/8” LOCK NUT

1/2” WASHER

1/2” LOCK NUT

1/2” LOW HEIGHT LOCK NUT

3/8 X 1” BOLT

3/8 X 2” BOLT
3/8 X 3” BOLT

3/8 X 4-1/2” BOLT

1/2 X 1-1/4” BOLT
1/2 X 2-3/4” BOLT
1/2 X 3-1/4” BOLT

1/2 X 4” BOLT

1/2 X 4-1/2” BOLT

1/2 X 5” BOLT

1-1/4” ROLL PIN

1/2” FLANGE BEARING

1/2” DIA. SPRING PIN

QTY

1
8
1
2

24

8

8
32
14

8

2

4

8

2

2

2

6

2

8

2

2

8

2

5

33

6

28

32

DO NOT SECURELY TIGHTEN

*

AT THIS TIME

1/2 X 3-1/4”

41

3/8 X 3” 37

*

29

1

23

26

31

5

3/8 X 3” 37

*

4

29

FIGURE 1

STEP 1:

• SECURELY assemble the REAR UPRIGHT (6) to the BASE (1) as shown in FIGURE 1 using two 1/2 X 3-1/4” BOLTS (41), four

1/2” WASHERS (32), and two 1/2” LOCK NUTS (33).

• LOOSELY assemble the RIGHT (4) and LEFT HANDLES (5) to the BASE (1) on their respective sides using four 3/8 X 3” BOL TS (37),
eight 3/8” W ASHERS (29), and four 3/8” LOCK NUTS (31) (DO NOT SECUREL Y TIGHTEN A T THIS TIME)

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

6

6

46

FIGURE 2

44 1/2 X 5”

1

44 1/2 X 5”

46

11

33

STEP 2:

• Insert four 1/2” FLANGE BEARINGS (46) into the BUSHINGS on the BASE (1), and four 1/2” FLANGE BEARINGS (46) into
the BUSHINGS on the PLATFORM (11) as shown in FIGURE 2.

• Assemble the PLATFORM (11) between the BUSHINGS on the BASE (1) as shown in FIGURE 2 using two 1/2 X 5” BOLTS (44)
and two 1/2” LOCK NUTS (33). (TIGHTEN THE CONNECTION ENOUGH TO REMOVE THE PLA Y , YET ALLOWING

THE PLA TFORM TO ROT A TE FREELY)

STEP 3:

• Attach four 1-1/2 X 3/4” PARAGLIDE STRIPS (27) to the end of
the PLATFORM ADJUSTMENT (12), and four 1-1/2 X 3/4”
P ARAGLIDE STRIPS (27) to the end of the PLATFORM SLEEVE
as shown in FIGURE 3 using the following steps:

• Thoroughly clean all surfaces where the PARAGLIDE
STRIPS (27) are to be attached.

• Remove the PARAGLIDE STRIPS (27) from the paper
backing and firmly apply them to all shown surfaces.

• SECURELY Assemble one 1/2” DIA. SPRING PIN (47) to the

SPRING PIN HOUSING, on the PLATFORM SLEEVE (2) as
shown in FIGURE 3. (!!! IMPORT ANT !!! TIGHTEN THE

NUT OF THE SPRING PIN SECURELY)

12

27

27

47

2

FIGURE 3

7

11

1/2 X 4” 42

12

47

33

2

1

1/2 X 4” 42

SECUREL Y TIGHTEN
HANDLES BOTH SIDES

33

FIGURE 4

STEP 4:

• Assemble the PLATFORM SLEEVE (2) to the BASE (1) as shown in FIGURE 4 using one 1/2 X 4” BOLT (42), and one 1/2”

LOCK NUT (33). (TIGHTEN THE CONNECTION ENOUGH TO REMOVE THE PLA Y, YET ALLOWING THE PLA T -

FORM SLEEVE TO ROT A TE FREELY)

• Pull back the 1/2” DIA. SPRING PIN (47) on the PLATFORM SLEEVE (2) and insert the PLATFORM ADJUSTMENT (12) into
it. Slide the PLATFORM ADJUSTMENT (12) down to the first adjustment hole and release the SPRING PIN (47).

• Assemble the PLATFORM ADJUSTMENT (12) to the PLATFORM (11) as shown in FIGURE 4 using one 1/2 X 4” BOLT (42),
and one 1/2” LOCK NUT (33). (TIGHTEN THE CONNECTION ENOUGH TO REMOVE THE PLAY , YET ALLOWING

THE PLA TFORM ADJUSTMENT T O ROT A TE FREEL Y)

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

8

6

6

43 1/2 X 4-1/2”

9

18

8

29

30

3/8 X 4-1/2” 38

1

FIGURE 5

STEP 5:

• LOOSELY assemble the LEFT (8) and RIGHT RAILS (9), along with the SEAT PAD (18) to the BASE (1) as shown in FIGURE 5
using two 3/8 X 4-1/2” BOLTS (38), two 3/8” LOCK WASHERS (30), and two 3/8” WASHERS (29). Temporarily assemble the
RAILS to the REAR UPRIGHT (6) using two 1/2 X 4-1/2” BOLTS (43) to aid in the assembly of this step.

9

16

1/2 X 4-1/2” 43

32

20

32

34 LOW
HEIGHT

26

25

FIGURE 6

STEP 6:

• Insert four 2” SQ. END CAPS (26) into the each end of the CARRIAGE (16) as shown in FIGURE 6.

• SECURELY assemble four 3” DIA. WHEELS (20) to the sides of the CARRIAGE (16) as shown in FIGURE 6 using four 1/2 X
4-1/2” BOLTS (43), eight 1/2” WASHERS (32), and four 1/2” LOW HEIGHT LOCK NUTS (34).

• Attach one 4 X 14” NON SKID STRIP (25) to the CARRIAGE (16) as shown in FIGURE 6.

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

6

10

LOW HEIGHT 34

BRACKETS

32

14

31

29

21

1/2 X 2-3/4” 40

3/8 X 2” 36

31

29

21

36 3/8 X 2”

16

FIGURE 7

STEP 7:

• SECURELY assemble two 2” DIA. WHEELS (21) to the BRACKETS on the left side of the CARRIAGE (16) as shown in
FIGURE 7 using two 3/8 X 2” BOLTS (36), four 3/8” WASHERS (29), and two 3/8” LOCK NUTS (31).

• Assemble the two ADJ. WHEEL BRACKETS (14) to the right side of the CARRIAGE (16) as shown in FIGURE 7 using two 1/2
X 2-3/4” BOLTS (40), two 1/2” WASHERS (32), and two 1/2” LOW HEIGHT LOCK NUTS (34). (NOTE: TIGHTEN BRACK-

ETS SECUREL Y TO THE CARRIAGE, THEN BACK NUT OFF 1/2 TURN TO ALLOW FOR ADJUSTMENT IN A
LA TTER STEP).

• SECURELY assemble two 2” DIA. WHEELS (21) to the ADJ. WHEEL BRACKETS (14) on the right side of the CARRIAGE
(16) as shown in FIGURE 7 using two 3/8 X 2” BOLTS (36), four 3/8” WASHERS (29), and two 3/8” LOCK NUTS (31).

11

16

43 1/2 X 4-1/2”

FIGURE 8

STEP 8:

9

SAFTEY

STOP

8

• Remove the two temporary 1/2 X 4-1/2” BOLTS (43) from STEP 5.

• Swing the LEFT (8) and RIGHT (9) RAILS out enough to insert the CARRIAGE ASSEMBLY (16) in between them. Allow the
CARRIAGE (16) to rest on the SAFETY STOPS underneath the RAILS. See FIGURE 8.

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

12

6

6

33

32

8

32

43 1/2 X 4-1/2”

9

14

16

21

14

REVERSE VIEW
FOR ASSEMBLY

6

FIGURE 9

STEP 9:

• SECURELY reassemble the LEFT (8) and RIGHT (9) RAILS to the REAR UPRIGHT (6) as shown in FIGURE 9 using the two 1/2
X 4-1/2” BOL TS (43), four 1/2” WASHERS (32), and two 1/2” LOCK NUTS (33). (!!! IMPORT ANT !!! BEFORE TIGHTENING

MOVE THE RAILS IN AS FAR AS POSSIBLE)

• SECURELY tighten the two 3/8 X 4-1/2” BOLTS (38) holding the SEAT PAD (18) from STEP 5. (!!! IMPORTANT !!! BEFORE
TIGHTENING MOVE THE RAILS IN AS FAR AS POSSIBLE)

• To adjust the side to side movement of the CARRIAGE (16), start by sliding the CARRIAGE (16) as far to the left as possible
inside the RAILS (8 & 9). Adjust the ADJ. WHEEL BRACKETS (14) out until the 2” DIA. WHEELS (21) contact the RIGHT
RAIL (9). SECURELY tighten bolt connection. See FIGURE 9 and REVERSE CARRIAGE VIEW.

13

41 1/2 X 3-1/4”

33

13

32

43 1/2 X 4-1/2”

33

32

16

FIGURE 10

STEP 10:

• SECURELY assemble both WEIGHT SUPPOR T (13) and PAD SUPPORTS 93)to the CARRIAGE (16) as shown in FIGURE 10 using
two 1/2 X 4-1/2” BOL TS (43), two 1/2 X 3-1/4” BOL TS (41), eight 1/2” WASHERS (32), and four 1/2” LOCK NUTS (33).

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

14

6

3/8 X 3” 37

30

29

26

17

33

32

3

41 1/2 X 3-1/4”

SURF ACE TO BE EVEN

FIGURE 11

STEP 11:

• SECURELY assemble the two PAD SUPPORTS (3) to the CARRIAGE (16) as shown in FIGURE 11 using two 1/2 X 3-1/4”
BOLTS (41), four 1/2” WASHERS (32), and two 1/2” LOCK NUTS (33).

• SECURELY assemble two SHOULDER P ADS (17) to the P AD SUPPOR TS (3) on the CARRIAGE (16) as shown in FIGURE 11 using
four 3/8 X 3” BOL TS (37), four 3/8” LOCK W ASHERS (30), and four 3/8” W ASHERS (29). (NOTE: THA T HOLES IN P ADS ARE

OFF-SET TO ONE SIDE)

15

10

47

24

FIGURE 12

STEP 12:

• Attach two 1-1/4” SQ. RUBBER BUMPERS (24) to the ends of the ANGLES of the FOOT PLATE (10) as shown in FIGURE 12.

• SECURELY assemble one 1/2” DIA. SPRING PIN (47) to the SPRING PIN HOUSING on the FOOT PLATE (10) as shown in
FIGURE 12. (!!! IMPORTANT !!! TIGHTEN THE NUT OF THE SPRING PIN SECURELY)

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

6

16

10

39 1/2 X 1-1/4”

32

34 LOW HEIGHT

16

FIGURE 13

STEP 13:

• Assemble the FOOT PLATE (10) to the CARRIAGE (16) as shown in FIGURE 13, using two 1/2 X 1-1/4” BOLTS (39), two 1/2”
WASHERS (32), and two 1/2” LOW HEIGHT LOCK NUTS (34). (TIGHTEN THE CONNECTION COMPLETELY, THEN

BACK THE NUTS OFF 1/4 TURN)

17

BUSHING

7

45

8

9

SURE-LOC

BUSHING

22

FIGURE 14

STEP 14:

• To assemble the CARRIAGE STOP BAR (7) to the side of the LEFT RAIL (8), start by inserting the top of the BAR (7) into the
BUSHING at the top of the RAIL as far as possible, then lower the BAR (7) into the SURE-LOC BUSHING at the bottom of the
RAIL. (MAKE SURE THE STOP PEGS ARE VERTICAL), then insert one 1-1/4” ROLL PIN (45) into the hole at the top of
the BAR (7). (DO NOT LET THE ROLL PIN PROTRUDE BENEATH THE BAR) Repeat this step on the RIGHT RAIL (9).

• Slide two 1-1/4 X 5” GRIPS (22) over the HANDLES on the CARRIAGE STOP BARS (7) as shown in FIGURE 14.

18

19

15

29

30

3/8 X 1” 35

FIGURE 15

STEP 15:

• SECURELY assemble the PAD STOP (15) to the BACK PAD (19) as shown in FIGURE 15 using two 3/8 X 1” BOLTS (35), two

3/8” LOCK WASHERS (30), and two 3/8” WASHERS (29).

MAKE SURE ALL CONNECTIONS ARE SECUREL Y TIGHTENED.

19

7

CARRIAGE

STOPS

16

BAR

HANDLES

11

SURE-LOC

BUSHING

35°,40°,45°

FIGURE 16

STEP 16:

• The PLATFORM (11) can adjust into three positions: 35, 40, and 45 degrees

• The HIP SLED was designed with the SURE-LOC SYSTEM for ultimate safety. To activate the CARRIAGE STOP BARS (7)from
either the LEG PRESS or HACK SQUAT position, begin by moving the CARRIAGE (16) up. Grasp the (HANDLES or BAR) on
the CARRIAGE STOP BARS (7) and (push or pull) up and rotate them out. Now the stops are out of the way to perform the
exercise.

• To stop the CARRIAGE (16) on one of the three carriage stops simply rotate the CARRIAGE STOP BARS (7) back up and allow
them to drop down into the SURE-LOC SYSTEM.

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

6

20

7

19

10

11

PLATFORM

HANLDE

FIGURE 17

STEP 17:

• To perform LEG PRESSES, center the BACK PAD (19) down on top of the PLATFORM (11) and lock the PAD STOP (15) on the
back of the BACK PAD (19) behind the PLATFORM HANDLE then rotate the FOOT PLATE (10) on the CARRIAGE (16) up
until the SPRING PIN engages the hole

• To perform CALF RAISES, move the CARRIAGE (16) to the top carriage stop of the CARRIAGE STOP BAR (7). Place feet on
the HORIZONT AL TUBE of the CARRIAGE (16). (WHERE THE NON-SKID STRIP IS LOCATED) (DO NOT ROTATE

THE CARRIAGE STOP BARS DOWN FOR THIS EXERCISE)

• To perform HACK SQUATS, make sure that the FOOT PLATE (10) of the CARRIAGE (16) is down. Position the BACK PAD
(19) between the SHOULDER P ADS of the CARRIAGE (16). (MAKE SURE THAT THE PAD ST OP IS RESTING ABOVE

THE CROSS TUBE ON THE CARRIAGE)

THIS CONCLUDES THE ASSEMBLY OF THE 835 HIP SLED SYSTEM.

21

MAINTENANCE

Please note:

* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water . Touch-up paint can be purchased from your ParaBody customer service representative
at [phone].

* Inspect equipment daily . Tighten all loose connections are replace worn parts immediately.
Failure to do so may result in serious injury

* PLEASE RECORD THE INFORMATION REQUESTED BELOW. IN THE EVENT
YOU MAY NEED SER VICE YOU WILL BE ASKED FOR THIS INFORMATION.
REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD AND
MAIL BACK.

MODEL #________________________

SERIAL #_________________________

DATE OF PURCHASE: _____________

DEALERS NAME: _________________

DEALERS PHONE #_______________

SERIAL NUMBER LOCA TIONS

Thank you for purchasing the ParaBody 835 Hip Sled System.

22

LIMITED W ARRANTY

ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONL Y.

1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired
or replaced by ParaBody. Terms: Lifetime – for so long as the Customer owns the ParaBody product.

2. LIMITED WARRANTY ON P ARTS. If the following part s are defective in material or workmanship, ParaBody will supply replacement parts:
all bolts, nuts, washers, bearings, bushings, pulleys, thumbscrews, collars, cable retaining clips, adjustable pre-stretch slides, roller pad
shafts, allen head bolts, weight selector pin, weight stack shaft, set screws, protector caps, adjustment chain, cotter pin, plunger , spring
and knob. Terms: Lifetime – for so long as the Customer owns the ParaBody product.

3. LIMITED WARRANTY ON CABLES AND UPHOLSTERY. If the coated cables or upholstery are defective in material or workmanship,
ParaBody will repair or replace them, at its option. Terms: Three (3) years.

4. CONDITIONS AND EXCEPTIONS. Any product misuse, abuse or alteration, any attempt to repair by a person other than an authorized
ParaBody Service Center, any improper assembly, accident, or any other condition resulting from occurrences beyond the control of
ParaBody will void this Limited Warranty .

5. REPLACEMENT AND REPAIR EXPENSES. ParaBody will provide only replacement parts or repair under this warranty. The Owner is
responsible for all other costs. Such costs may include, but are not limited to: a. labor charges for service, removal, repair or reinstallation
of the ParaBody product or any component part; b. shipping, delivery, handling and administrative charges for returning part s to ParaBody;
and c. all necessary or incidental costs related to installation of the replacement parts.

6. SHIPPING . If shipping by the Owners is deemed necessary (in sole discretion of ParaBody), parts should be shipped in their original carton
or equivalent packaging, fully insured with shipping charges prepaid. ParaBody will not assume any responsibility for any loss or damage
incurred in shipping.

7. CLAIM PROCEDURES. If service on your ParaBody product is required during the warranty period, please contact our Customer Service
Department at 1-800-328-9714 for instructions regarding returning or replacing parts. Please have available the following information: (i) the
dealer’s name; (ii) the date of purchase; (iii) the serial # (s) of your product (the serial number location is called out on the final assembly
drawing included with your assembly instruction); (iv) a description of the nature of the problem.

8. OWNER’S RIGHT . This Limited W arranty gives you specific legal rights. Y ou may also have other rights, which vary depending on local law .

9. LIMITATION OF IMPLIED W ARRANTIES. All implied warranties, except to the extent prohibited by applicable law , shall have no greater
duration than the warranty period set forth above. There are no warranties which extend beyond the description in this Limited Warranty .
Because local laws do not allow limitations on how long an implied warranty lasts, the above limitations may not apply to you.

10. DISCLAIMER. No other express warranty has been made or will be made on behalf of ParaBody with respect to any ParaBody product or
the operation, repair or replacement of any ParaBody product. ParaBody shall not be responsible for injury , loss of use of the ParaBody
product, inconvenience, loss or damage to personal property, whether direct or indirect, and incidental or consequential damages, so the
above limitation or exclusion may not apply to you.

NOTES:

23

LIFE FITNESS

14150 Sunfish Lake Blvd. Ramsey Minnesota, 55303 U.S.A.

T el: 763.323.4500 Fax: [phone]

800.328.9714 (T oll-free within the U.S. and Canada)
www.parabody.com

INTERNATIONAL OFFICES

Life FitnessAtlantic BV
Atlantic Headquarters
Bijdorpplein 25-31
2992 LB Barendrecht
The Netherlands
Phone: [phone]
Fax: [phone]

Life Fitness EUROPE GmbH
Siemensstrasse 3
85716 Unterschleissheim
Germany
Phone: [phone]
Fax: [phone]

Life Fitness Italia S.R.L.
V ia Elvas 92
39042 Bressanone
Italy
Phone: [phone]
Fax: [phone]

Life Fitness (UK) Ltd.
Queen Adelaide
Ely , Cambs CB7 4UB
United Kingdom
Phone CSS: [phone]
Fax CSS: [phone]

Life Fitness Benelux N.V.
Bijdorpplein 25-31
2992 LB Barendrecht
The Netherlands
Phone: [phone]
Fax: [phone]

Life Fitness Japan
8/F , Nippon Brunswick Building
5-27-7 Sendagaya
Shibuya-Ku, T okyo 151-0051
Japan
Phone: [phone]
Fax: [phone]

Life Fitness Asia Pacific Limited
Room 2610, Miramar T ower
132 Nathan Road, T simshatsui
Kowloon, Hong Kong
Phone: [phone]
Fax: [phone]

24

Life Fitness Do Brazil
Al. Rio Negro, 433-Predio 2-Sala 2
3

º andar (Confab)

Aplhaville-Barueri-Sao Paulo
CEP: 06454-904
Brazil
Phone: [phone]
Fax: [phone]