I:)E}F604
Volume 2
Optional Shroud Kit
S EMB L Y
NSTRUCTIOHS
B Y
Our Strength Begins With Listening.
P A R
A B
625
O
D Y
IMPORTANT
KEEP ALL FRAME BOLT CONNECTIONS LOOSE UNTIL INSTRUCTED IN
THE ASSEMBLY STEP SEQUENCES TO SECURELY TIGHTEN.
NOTE:¯The ParaBody Factor 625 base unit must be assembled on
a flat, level surface to assure its proper function.
¯
ParaBody strongly recommends that this product be assembled
by two persons to avoid possible iniury.
WELDMENTS/PARTS:
ITEM
1
2 Shroud Rod
3
4 Poly-Lock 3/4" x 4" (20 pieces in Bag)
NAME/DESCRIPTION QTY.
Optionnl Shroud
Dbl. Sided FoamTape 3/4"x72" (Cl196-01)
(PB3179-01)
(PB3189-01) 10
10
5
1
!!I llI
.WARNING...
MAKE SURE SNAP HOOKS ARE FASTENED BEFORE DOING EXERaSES.
!!!WARNING!!!-
LAT BAR IS NOT TO BE USED FOR PULL-UPS.
NOTE: We recommend cleaning your product (pads and the frame members) on a regular
basis, using warm soapy water. Also, touch-up paint can be purchased from your
ParaBody Customer Service Representative nt 1-800-328-9)’14.
1. Lay the shroud on a dean/flat/firm surface.
Adhere one roll of the double sided foam tape
2.
3/4"x 72" to one of the shroud rods. Secure two (2)
of the 3/4"x 4" Poly-locks to the shroud rod (one on
each end of the side opposite the double sided foam
tape). Do this for the remaining (1) shroud rod.
Using a template or tape measure, scribe the 21/2
3.
location for the shroud rods on the smooth/non
screened side of the shrouds.
Remove the backing paper from the double sided
4.
foam tape on one of the shroud rods and carefully
fasten the shroud rod to the shroud us shown. Repeat
this for the second shroud rod. The shroud rod should
be applied to the smooth or non screened side of each
shroud.
"
DOUBLE SIDED FOAM TAPE
SHROUD
3/4" X 72" ROLLS
2 ROLLS/SHROUD
SHROUD ROD
POLY-LOCK
3/4. X4"
--L
~ 3/4. X4.
POLY-LOCK
4/SHROUD
LEG PRESS/2 STACK SHROUD
NO HAIRCELL TEXTURE ON THIS SIDE
SHROUD ROD
2/SHROUD
If you have any questions on the proper assembly of equipment,
do not hesitate to call the ParaBody Customer Service Department at
T -800-328-97 T 4
Do not mark this box!
Document: 11000199
PARAB6DY INC.
FACTOR 625 D-RING RETRO KIT
607/608
PRODUCT ASSEMBLY
INSTRUCTION SHEETS
TOOLS REQUIRED FOR ASSEMBLY
RATCHET
9/16 INCH SOCKET
7/16 INCH WRENCH
ADJUSTABLE WRENCH
REVISION: A
If you experience any problem with the assembly of this product, please contact yo~ar dealer
or your PARABODY Customer Service Representative at:
1-800-328-9714
607/608 FACTOR 625 D-RING RETRO KIT ASSEMBLY PARTS LIST
HARDWARE/PARTS:
ITEM NAME/DESCRIPTION
D-RING WLDMNT ........................................................
2.
3.
4.
5.
6.
7
8.
9.
ROTARY CABLE ..........................................................
LEG PRESS/ROTARY CABLE .....................................
PEC/D-RING CABLE ...........
MULTI PRESS CABLE ..........
LAT CABLE ................................................... (6405901)
SWIVEL ..........................................................................
D-RING CABLE CLIP ...................................................
¯ VINYL CAP ....................................................................
(6352301) ........................ ~ ...............
(6406001) ........................................
(6405701) .......................................
~ ........
.~.. ..............................
..X. .....................................(6405801) ...........
(6406101) .......................................
"’’!’’~" "’~’"
(3201501) .......................................
(3200501) .......................................
(3201402) .......................................
QT~(
=....~.~,.~. ...............
:"~ ...............
......
1
I
1
1
1
1
4
4
1
607/608
FACTOR 625 D-RING RETRO KIT ASSEMBLY INSTRUCTIONS
STEP 1: D-RING’INSTALLATION
1.
To assemble the new D-RING to the FACTOR 625, use the following steps:
¯
Remove all the CABLES from the old D-RING.
¯
Loosen, and remove the two (2) 1/4-20 NUTS, and the 1/4 IN. WASHER from the end of the
RING CABLE.
¯
Slide one (1) VINYL CAP over the end of the new D-RING.
¯
Remove and discard old D-RING, and replace with the new D-RING.
¯
LOOSELY attach the 1/4 IN. WASHER, and the two (2) 1/4 IN. NUTS to the end of the D..RING
CABLE. (POSITION THE 1/4-28 NUTS HALF WAY UP ON THE THREADS OF TIlE DRING CABLE UNTIL CABLE INSTALLATION IS COMPLETE. DO NOT TIGI-][TEN NUTS
AT THIS TIME)
STEP: 2 CABLE INSTALLATION
NOTE: FOR EASE OF CABLE REPLACEMENT THE D-RING END OF THE OLD CABLES MAY BE
CUT OFF. IF THIS IS NOT POSSIBLE SOME PULLEYS WILL NEED TO BE LOOSENED AND
REMOVED TEMPORALLY IN ORDER TO REMOVE OLD CABLES.
To replace the ROTARY CABLE (6406001), or (depending on which RETRO KIT being assembled)
the LEG PRESS/ROTARY CABLE (6405701), see the drawing, and use the following steps:
¯
Remove the SHOCK CORD from the BASE of the 625, then remove it from the end of the old
ROTARY CABLE.
¯ Remove and discard the old ROTARY CABLE, and replace it with the new ROTARY CABLE.
(THE CABLE MUST BE ROUTED THE SAME WAY IT WAS REMOVED).
Run the ROTARY CABLE through the hole of the D-RING shown in (DETAIL A )on drawing, and
¯
attach one (1) D-RING CABLE CLIP around the ball end of the ROTARY CABLE.
¯ Attach one (1) SHOCK CORD to the D-RING CABLE CLIP on the end of the ROTARY CABLE
as shown in (DETAIL A).
Route the SHOCK CORD the same way that it was removed. Attach one (I) SWIVEL to the end
¯
the SHOCK CORD, and slide the swivel over the BAR on the BASE as shown in (VIEW B-B).
Replace the SHOCK CORD to its original position on the BAR
¯ IMPORTANT: MAKE SURE THAT THE D-RING CABLE CLIP IS POSITIONED
VERTICALLY ABOVE THE D-RING.
607/608 FACTOR 625 D-RING RETRO KIT ASSEMBLY INSTRUCTIONS
3.
Replace the remaining CABLES in the following’or~er using the steps outlined in STEP 2: (PLEASE
REPLACE ONE CABLE AT A TIME, REPLACING IN A CLOCKWISE DIRECTION AROUND
THE D-RING. SEE DRAWING)
¯
PEC/D-RING CABLE (6406101)
¯
MULTI PRESS CABLE (6405801)
¯
LAT CABLE (6405901)
When all of the CABLES have been replaced, adjust the height of the D-RING on the D-RING CABLE
by raising or lowering the two (2) 1/4-28 IN. NUTS. (THE D-RING SHOULD REST JUST BELOW
THE D-RING CABLE CLIPS ON THE CABLE ENDS). When the correct height is obtained.
SECURELY tighten the two (2) 1/4-28 nuts together.
Loading...