ParaBody 894104A User Manual

!

Serious Steel

894104 PEC DEC OPTION

Illl

ASSEMBLY INSTRUCTIONS

Part # 6820101

I

I

1

Revision:4/26/99

[ IMPORTANT NOTES’[

WELCOME TO THE WORLD OF SeriOUS ~e~!lt

Please no~e:

* Thank you for purchasing the Parabody 894104 PEC DEC OPTION. Please read these
instructions thoroughly and keep them for future reference. This product r~m,,;t be assembl~l on a

fiat, level surface to assure its proper function.

* We recommend cleaning your product (pads and frame) on a regular brads, using warm soapy

water. Touch-up paint can be purchased from your Parabody customer serape representative

at [phone].

There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:

Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.

1.
Failure to do so may result in serious injury.

2. Do not allow minors or children to play on or around this equipment.

3. Exercise with care to avoid injury.
If unsure of proper use of equipment, call your local Parabody distributor or call the

4.
Parabody customer service department at [phone].

5. Consult a physician before beginning any exercise program.

I Tools Required for Assembly I

*

3/4" wrench

* 9/16" wrench ~
* Ratchet with 3/4" and 9/16" sockets

Adjustable wrench

*

* Tape measure

[ Bolt Length Ruler [

NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSI])E OF THE HEAD OF THE BOLT.

BOLT LENGTH RULER:

1/2

I I I

I

1

1/2

I I I I

I

BOLT LENGTH

I

2

1/2

I I I I

I

1/2

I

1/2

I

1/2 l

6

PARTS LIST

KEY PART #

1 6818103

6818403 PEC DEC ARM LEFT

2

3 6818503 PEC DEC ARM RIGHT

6818303 CENTER PULLEY BRACKET

4

6686802 PULLEY BRACKET

5
6 6597402
7 6176201 4 X 12" ROLLER PAD

8 3116201
9 6492201 94-1/2" CABLE

10 6819001
11 6405201 2" SQ END CAP

DESCRIPTION

BEARING HOUSING

BACK PAD

3-1/2" PULLEY

134-3/4" CABLE

FIGURE 1

QTY

1 12 61407O1
1

1 14
1
1

1 17

2

5 19

1 20 3102801

1

6 22

KE~ PART#

13 6533501

3102933
15 3102922
16 3102918

3102501

18 3102801

3102502

21

3104901
3102804 1/2" LOW~EIGHTLOCK-NUT

DES ’,RIPTION

1 X 1" GUIDE

CABLE Pd~TAINING CLIP

3/8. 2" BOLT

3/8 X 2-3/4" BOLT

1/2 X 3-1/4" BOLT

3/8- V~/ASHER

3/8" LOCK NOT

1/2’ RASHER

1/2" LOCK NUT

3/4"FLPiNC~BEARING

QTY

2

4

5
2

2
6

5 "

2
2
4

2

STEP 1:
¯ Remove the lower CABLE from the UPRIGHT FRAME and PULLEY BLOCK and discard as shown in FIGLrRE 1.

¯

Remove eight 9/16" HOLE PLUGS from the UPRIGHT FRA~ME if applicable. See FIGURE 1.

FIGURE 2

STEP 2:

¯ Assemble t~vo 1 X 1" GLIDES (12) to the BEARING HOUSING (1) as sho~vn in FIGURE

¯ Insert t~vo 2" SQ. END CAPS (11) to the ends of the BEARING HOUSING (1) as shown in FIGURE

1/2 [ 1/2 [

1/2

[ 1/2

4

[

1/2 ~

5

1/2

I

6