PANJIT PS100RS, PS1010RS, PS101RS, PS102RS, PS104RS Datasheet

PS100RS THRU PS1010RS

FEATURE

S

MECHANICAL DATA

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTIC

S

V

V

V

A

Peak Forward Surge Current 8.3ms single half sinewave superimposed on rated load(JECEC method

)

A

P

/

W

n

s

Operating and Storage Temperature Range TJ,

T

STG

A-405

FAST SWITCHING PLASTIC DIODES

VOLTAGE - 50 to 1000 Volts CURRENT - 1.0 A mpere

l

High current capability

l

Plastic package has Underwriters Laboratory
Flammability Classification 94V-O Utilizing
Flame Retardant Epoxy Molding Compound

l 1.0 ampere operation at TA=55 ¢J with no thermal runaway

l

Fast switching for high efficiency

l

Exceeds environmental standards of MIL-S-19500/228

l

Low leakage

Case: Molded plastic, A-405
Terminals: Plated axial leads, solderable per MIL-STD-202,
Method 208
Polarity: Color band denotes cathode
Mounting Position: Any
Weight: 0.008 ounce, 0.22 gram

Ratings at 25¢J ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.

PS100RS PS101RS PS102RS PS104RS PS106RS PS108RS PS1010RS UNITS

Maximum Recurrent Peak Reverse Voltage 50 100 200 400 600 800 1000
Maximum RMS Voltage 35 70 140 280 420 560 700
Maximum DC Blocking Voltage 50 100 200 400 600 800 1000
Maximum Average Forward Rectified

1.0

Current .375"(9.5mm) lead length at TA=55 ¢J

30

Maximum Forward Voltage at 1.0A DC 1.3
Maximum Reverse Current TJ=25 ¢J
at Rated DC Blocking Voltage TJ=100 ¢J

5.0

500

Typical Junction capacitance (Note 1) CJ 12
Typical Thermal Resistance (Note 3) R £KJA 67

Maximum Reverse Recovery Time(Note 2) 150 150 150 150 250 500 500

-55 to +150

NOTES:

1. Measured at 1 MHz and applied reverse voltage of 4.0 VDC

2. Reverse Recovery T est Conditions: IF=.5A, IR=1A, Irr=.25A

3. Thermal resistance from junction to ambient and from junction to lead at 0.375"(9.5mm) lead length P.C.B.
mounted

V

£g

A

£g

A

F

¢J

¢J

RATING AND CHARACTERISTIC CURVES

NOTE:1.Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF 2.Rise Time = 10ns max. Source Impedance = 50 Ohms

r

r

SET TIME

1c

m

BASE FO

R

50 ns/c

m

TJ = 25

WIDTH = 300£gs

INSTANTANEOUS FORWARD VOLTAGE, VOLT

S

RESISTIVE OR INDUCTIV

E

AMBIENT TEMPERATURE,

¢J

TJ = 25¢JREVERSE VOLTAGE, Vd

c

NUMBER OF CYCLES AT 60H

z

PS100RS THRU PS1010RS

Fig. 1-REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM

10

1

AMPERES

0.1

PULSE

0.6

1% DUTY CYCLE

0.8

1.0 1.2 1.4 1.6

INSTANTANEOUS FORWARD CURRENT,

0.01

0.2

0.4

¢J

t

+0.5A

0

-0.25

-1.0

1.6

1.4

1.2

1.0
.8
.6
.4
.2

CURRENT AMPERES

0

AVERAGE FORWARD RECTIFIED

0

20

40

60

MAXIMUM AVERAGE CURRENT RATING
SINGLE PHASE, HALF WAVE 60Hz

LOAD .375"(9.5mm) LEAD LENGTHS

80 100

120

140

160

180

Fig. 2-TYPICAL INSTANTANEOUS

Fig. 3-FORWARD CURRENT DERATING CURVE

FORWARD CHARACTERISTICS

100

10

CAPACITANCE, pF

1

1

4 10 100

30

24

18

12

6

FORWARD SURGE CURRENT,

1 2 4 6 8 10 20 60 80 10040

AMPERES pk (HALF-SINE WAVE)

Fig. 4-TYPICAL JUNCTION CAPACITANCE Fig. 5-PEAK FORWARD SURGE CURRENT