Page 1
Camera Drive Unit
POWER
Camera Drive Unit WV-PS
15
ON
OFF
Operating Instructions
Model No. WV-PS15
ENGLISH
DEUTSCH
FRANÇAIS
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
ESPAÑOL
Page 2
ENGLISH VERSION
We declare under our sole responsibility that the product
to which this declaration relates is in conformity with the
standards or other normative documents following the provisions of Directives EEC/73/23 and EEC/89/336.
Noi dichiariamo sotto nostra esclusiva responsabilità che il
prodotto a cui si riferisce la presente dichiarazione risulta
conforme ai seguenti standard o altri documenti normativi
conformi alle disposizioni delle direttive CEE/73/23 e CEE/
89/336.
Wij verklaren als enige aansprakelijke, dat het product
waarop deze verklaring betrekking heeft, voldoet aan de
volgende normen of andere normatieve documenten,
overeenkomstig de bepalingen van Richtlijnen 73/23/EEC
en 89/336/EEC.
Vi erklærer os eneansvarlige for, at dette produkt, som
denne deklaration omhandler, er i overensstemmelse med
standarder eller andre normative dokumenter i følge
bestemmelserne i direktivene 73/23/EEC og 89/336/EEC.
Caution:
Before attempting to connect or operate this
product, please read the label on the bottom.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is interned to alert the
user to the presence of uninsulated "dangerous voltage" within the
product's enclosure that may be
of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance (servicing) instructions in
the literature accompanying the
appliance.
Vi deklarerar härmed värt fulla ansvar för att den produkt
till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa
dokument som framställs i EEC-direktiv nr. 73/23 och 89/
336.
Ilmoitamme yksinomaisella vastuullamme, että tuote, jota
tämä ilmoitus koskee, noudattaa seuraavia standardeja tai
muita ohjeellisia asiakirjoja, jotka noudattavat direktiivien
73/23/EEC ja 89/336/EE. säädöksiä.
Vi erklærer oss alene ansvarlige for at produktet som
denne erklæringen gjelder for, er i overensstemmelse med
følgende normer eller andre normgivende dokumenter
som følger bestemmelsene i direktivene 73/23/EEC og 89/
336/EEC.
For U.K.
FOR YOUR SAFETY PLEASE READ THE FOLLOWING
TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains
plug for your safety and convenience.
A 13 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that
the replacement fuse has a rating of 13 amp and that it is
approved by ASTA or BSI to BS1362.
Check for the ASTA mark
body of the fuse.
If the plug contains a removable fuse cover you must
ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your
local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR
THE SOCKET OUTLET IN YOUR HOME THEN THE
FUSE SHOULD BE REMOVED AND THE PLUG CUT
OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL
SHOCK IF THE CUT OFF PLUG IS INSERTED INTO
ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code
as shown below.
If in any doubt please consult a qualified electrician.
WARNING: This apparatus must be earthed.
The wires in this mains lead are coloured in accordance
with the following code.
As the colours of the wire in the mains lead of this
appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows.
The wire which is coloured green-and-yellow must be
connected to the terminal in the plug which is marked with
the letter E or by the earth symbol
green-and-yellow.
The wire which is coloured blue must be connected to
the terminal in the plug which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected
to the terminal in the plug which is marked with the letter L
or coloured red.
How to replace the fuse
Open the fuse compartment with
a screwdriver and replace the fuse
and fuse cover.
Green-and-yellow: Earth
Blue: Neutral
Brown: Live
H or the BSI mark G on the
IMPORTANT
I or coloured green or
2
2
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
Page 3
CONTENTS
PREFACE ...................................................................................................................................................... 4
FEATURES .................................................................................................................................................... 4
PRECAUTIONS ............................................................................................................................................. 4
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ...................................................................... 5
■ Front View .............................................................................................................................................. 5
■ Rear View ............................................................................................................................................... 5
SYSTEM CONNECTION ............................................................................................................................... 6
SPECIFICATIONS ......................................................................................................................................... 8
ENGLISH
3
The serial number of this product may be found
on the bottom of the unit.
You should note the serial number of this unit in
the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft.
Model No.
Serial No.
Page 4
PREF ACE
The Panasonic WV-PS15 Camera Drive Unit drives VP (Video and Power) multiplex camera.
This simple system is designed to meet the surveillance and security needs of offices, factories, public
and residential buildings, etc.
FEATURES
• VP multiplex camera of the specified model
can be driven by WV-PS15.
• A single coaxial cable connects camera of
the specified model and camera input to the
Camera Drive Unit.
It supplies DC power, controls data and vertical drive pulses to the camera, and receives
video and audio (*) signals from the camera.
PRECAUTIONS
• Refer all work related to the installation of
this product to qualified service personnel
or system installers.
• Do not block the ventilation opening or
slots on the cover.
To prevent the appliance temperature from
rising, place the appliance at least 5 cm (2
inches) away from the wall.
• Do not drop metallic parts through slots.
This could permanently damage the
appliance. Turn the power off immediately
and refer servicing to qualified service
personnel.
• Do not attempt to disassemble the
appliance.
To prevent electric shock, do not remove
screws or covers.
There are no user-serviceable parts inside.
Refer maintenance to qualified service personnel.
• Handle the appliance with care.
Do not strike or shake, as this may damage
the appliance.
• Controls camera setup through the specified
outboard device connected.
• VD/SYNC IN and OUT connectors provided
for synchronizing in parallel connection.
(*) If an applicable camera is connected.
• Do not expose the appliance to water or
moisture, nor try to operate it in wet areas.
Do take immediate action if the appliance
becomes wet. Turn the power off and refer
servicing to qualified service personnel.
Moisture can damage the appliance and also
cause electric shock.
• Do not use strong or abrasive detergents
when cleaning the appliance body.
Use a dry cloth to clean the appliance when
it is dirty.
When the dirt is hard to remove, use a mild
detergent and wipe gently.
• Do not operate the appliance beyond its
specified temperature, humidity or power
source ratings.
Do not use the appliance in an extreme environment where high temperature or high
humidity exists.
Use the appliance at temperatures within
–10°C - +50°C (14°F - 122°F) and a humidity
below 90 %.
The input power source for this appliance is
220-240 V AC 50 Hz.
4
Page 5
ON
OFF
POWER
GND
SIGNAL
(4V[p-p]75Ω)
CAMERAINVIDEO
OUT
AUDIO
OUT
VD/SYNCINVD/SYNC
OUT
wert yu
i
q
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
■ Front View ■ Rear View
q Power On/Off Switch (POWER ON/OFF)
This switch is used to turn the camera drive
unit and connected camera on and off. The
indicator lights up when the camera drive
unit is switched on.
When turns this switch off, the power supply
does not interrupt. In such a case, disconnect the AC cord or turn the circuit breaker
off.
w Camera Input Connector (CAMERA IN)
This connector receives colour or B/W composite video signal from the camera. It also
supplies DC power and vertical drive pulses
for synchronizing signals to the camera and
receive video and audio signals from the
camera.
e Video Output Connector (VIDEO OUT)
Video signals from the camera is output from
this connector for input to outboard devices.
r Audio Output Connector (AUDIO OUT)
Audio signal from the camera is output from
this connector for input to the outboard
devices (if an applicable camera is connected).
t VD/SYNC Input Connector (VD/SYNC IN)
The VD (Vertical Drive) pulse or VS (Video
Sync) signal is supplied to this connector for
synchronizing the system.
y VD/SYNC Output Connector (VD/SYNC
OUT)
The VD (Vertical Drive) pulse or VS (Video
Sync) signal is output from this connector for
synchronizing other system components.
u
Signal Ground Terminal (SIGNAL GND)
i
AC Cord
5
Page 6
654321
GND
SIGNAL
(4V[p-p]75Ω)
CAMERAINVIDEO
OUT
AUDIO
OUT
VD/SYNCINVD/SYNC
OUT
GND
SIGNAL
(4V[p-p]75Ω)
CAMERAINVIDEO
OUT
AUDIO
OUT
VD/SYNCINVD/SYNC
OUT
Camera
Camera
Monitor
Video Switcher
VD/SYNC
OUT
VD/SYNC IN
CAMERA IN
CAMERA IN
VIDEO IN
VIDEO IN
VIDEO OUT
VIDEO IN
VIDEO OUT
VIDEO
OUT
SYSTEM CONNECTION
OPERATE
REMOTE
NORMAL PROG
ALARM
RESET
SYSTEM
ALARM OFF
Camera Controller WV-RM
7070
Camera
MonitorCamera Controller
WV-RM70
DATA DATA
VD2/POWER
CAMERA IN VIDEO IN VIDEO INVIDEO OUT
VIDEO OUT
GND
SIGNAL
(4V[p-p]75Ω)
CAMERAINVIDEO
OUT
AUDIO
OUT
VD/SYNCINVD/SYNC
OUT
Cautions:
• Keep the POWER switch of the camera
drive unit in the OFF (l) position during
connection. If camera drive unit power is
kept on during connection, the protection circuit that protects the unit in case
of the wrong connection will operate and
prevent the cameras from functioning.
<Extended System >
• Connect only VP multiplex camera of the
specified model. If other camera is connected, the protection circuit will keep
the camera drive unit out of operation.
● Connection with the Camera Controller WV-RM70
6
Page 7
1. Connect a coaxial cable from a camera to a
CAMERA IN connector of the camera drive
unit. Maximum cable lengths are approximately as shown below.
Coaxial DC R/300m Maximum
Cable Type (1000 ft.) of Cable Length
Inner Conductor
RG-59/U Less than 30
RG-6/U Less than 12 Ω 500 m (1650 ft.)
Ω 200 m (660 ft.)
The maximum DC resistance of the cable
between the camera and camera drive unit is
20 Ω.
2. Connect a coaxial cable from a video monitor
to the VIDEO OUT connector of the camera
drive unit. Maximum cable lengths are approximately as shown below.
External VD/SYNC Signal
Signal Level
The VD/SYNC IN connector receives the VD or
VS synchronizing signal for external synchronization.
• VD: 4 V[p-p]/75 Ω
• Composite Sync: 4 V[p-p]/75 Ω
Type of
coaxial cable
Recommended
Maximum
cable length
(m)
(ft)
RG-59/U
(3C-2V)
250
825
RG-6/U
(5C-2V)
500
1 650
RG-11/U
(7C-2V)
600
1 980
Note:
If the length of the coaxial cable between
the camera drive unit and the video monitor exceeds the distance shown in the
above table, a cable loss compensator
should be used between the camera
drive unit and the video monitor.
3. After connecting the specified camera to the
camera drive unit, connect the audio cable
between the monitor and AUDIO OUT connector of the camera drive unit.
• VS: 1 V[p-p]/75 Ω
Accuracy of vertical signal
Vertical frequency: 50 Hz ± 0.0013 Hz
Relation between VD/SYNC IN and VD/SYNC
OUT
The signals from the VD/SYNC OUT connector
differ depending on the connected camera and
the signals received at the VD/SYNC IN connector of the camera drive unit.
The signals supplied from VD/SYNC OUT are as
follows:
Signal to
VD/SYNC
Connected
Camera
WV-BP50E
or
WV-CP110E
IN
No signal VD signal
Composite
signal
VD signal
Composite
signal
Composite
signal
7
Page 8
SPECIFICATIONS
Power Source: 220-240 V AC 50 Hz
Power Consumption: Approx. 17 W
Camera Input: 1.0 V[p-p]/75 Ω, BNC Connector
Video Output: 1.0 V[p-p]/75 Ω, BNC Connector
Audio Output: –10 dB/600 Ω unbalanced, RCA pin jack
Camera Power Supply: Regulated current multiplex method (350 mA)
Maximum Distance to Camera: Coaxial DC R/300m (1 000 ft.) of Maximum
Cable Type Inner Conductor Cable Length
RG-59/U Less than 30 Ω 200 m (660 ft.)
RG-6/U Less than 12 Ω 500 m (1 650 ft.)
Maximum DC Resistance: Between camera and camera drive unit: 20 Ω
VD/SYNC Input: 4.0 V[p-p]/75 Ω Negative going or VS 1 V[p-p]/75 Ω, BNC
Connector
VD/SYNC Output: 4.0 V[p-p]/75 Ω Negative going, BNC Connector
Ambient Operating Temperature: –10°C – +50°C (14°F – 122°F)
Ambient Operating Humidity: Less than 90 %
Dimensions: 138 (W) X 44 (H) X 185 (D) mm
5-7/16” (W) x 1-3/4” (H) x 7-5/16” (D)
Weight: 1.0 kg (2.2 lbs.)
Weight and dimensions shown are approximate.
Specifications are subject to change without notice.
8
Page 9
Matsushita Electric Industrial Co., Ltd.
Central P.O. Box 288, Osaka 530-91, Japan
© Matsushita Communication Industrial Co.,Ltd. 2000
N0100-0 YWV8QA5385AN Printed in Japan
Gedruckt in Japan
Imprimé au Japon
Impreso en Japón
Loading...