Panasonic WJ-SXB151 Operation Manual
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Multiplexer Board
Model No.
WJ-SXB151
WARNING:
• All work related to the installation of this product should be made by qualified service personnel or system installers.
■ General ................................................................................................................. 2
■ Precautions ........................................................................................................... 2
■ Procedure Flow ..................................................................................................... 2
HARDWARE PREPARATION .................................................................................... 3
■ Installation of Multiplexer Board WJ-SXB151 ....................................................... 3
■ Connection with WJ-HD100 Series or Time-lapse VCR ....................................... 5
FIRMWARE UPDATE ................................................................................................ 6
■ Installation of SX150 Program Writer .................................................................... 6
■ Firmware Update of SX150 Program Writer ......................................................... 6
■ Error List ............................................................................................................... 8
TROUBLESHOOTING .............................................................................................. 9
■ Specifications ..................................................................................................... 10
■ Accessories ........................................................................................................ 10
■ Procedure Flow
* The version is displayed in WJ-SX150 SETUP
MENU.
(Refer to the matrix switcher’s operating instructions.)
** The version printed on the CD-ROM label.
*** Refer to the matrix switcher’s operating instructions.
-2-
■ Precautions
• Unplug the power cord from the Matrix Switcher WJSX150 before installing the board.
• Avoid shock and vibration
Shock or vibration may damage the board while
operating or not operating.
• Pay attention to static electricity
Make certain to keep the board inside the anti-static
sack until it is installed.
Put your hand on a metallic surface, other than the
board to discharge static electricity before installation.
Do not touch components mounted on the board
directly by hand.
Hold only both edges of the board when installing.
• Consumable part
Contact your dealer for replacement of the following
part when the time comes.
Fan unit needs replacement after around 30 000
hours of operation.
■ General
The Multiplexer Board WJ-SXB151 is an option for the
Matrix Switcher WJ-SX150. It enables multiscreen display, zoom*, still**, and multiscreen sequence. It also
enables the operation of specified digital disk recorders
or time-lapse VCRs, when connected to them via the
matrix switcher’s DATA HDR or SERIAL port.
Read the operating instructions included in the matrix
switcher for details.
* Available when playing back a spot picture
** Available when displaying the live images in the multi-
screen display or playing back a spot/multiscreen
picture.
Start
Firmware version check*
CD-ROM version check**
CD-ROM version is newer
than SETUP MENU.
WJ-SXB151 Installation
Connections***
Program Writer
Installation
SX150
Firmware Update
Setup Procedures***
Confirmation of WJ-SX150 operation***
SETUP MENU version is
newer or equal to CD-ROM.
-3-
HARDW ARE PREPARATION
■ Installation of Multiplexer
Board WJ-SXB151
● The Features of Multiplexer Board
WJ-SXB151
Multiplexer Board WJ-SXB151 is an optional accessory
specified for Matrix Switcher WJ-SX150.
The board installation will add the following functions to
the matrix switcher.
•A monitor can display up to 16 camera images in
multiscreen segments. (Multiscreen output)
A desired image can be displayed as a still picture.
(Still output)
• The matrix switcher can detect a moving object with
the brightness change and send an alarm to the
external equipments. (Motion detector)
• The matrix switcher can multiplex the images of all
the cameras connected to Digital Disk Recorder
WJ-HD100 Series or a time-lapse VCR.
• When an alarm becomes active, the accompanied
image can be recorded by priority. (Alarm priority
recording).
• The playback of the specified camera image while
the alarm priority recording is available.
• When playing back the multiplexed images, spot
output (displaying of a selected image's display) or
the multiscreen output is available.
Notes:
• When using Digital Disk Recorder WJ-HD500
Series, all the functions related to Multiplexer
Board WJ-SXB151 becomes unavailable.
• To use these functions, the setup through SX150
Setup Utility is necessary as well as the installation. For details, refer to SX150 Setup Utility.
● Installation procedures
1. Disconnect the matrix switcher's power plug from
the outlet.
2. Open the top cover by removing 11 screws and
sliding it backward. (Refer to the illustration.)
3. Install the cooling fan.
q Open the blank panel at the right side of the
back panel.
Remove the two screws. (Refer to the illustration.)
w Remove the 3P connector attached to CN14,
and connect the power cord of the cooling fan
to CN14.
Main circuit board
Sub circuit board
Screws (x 2)
CN14
Power cord (Cooling fan)
-4-
e Fasten the cooling fan with the screws removed
in step q.
4. Install the Multiplexer board.
q Remove the flatcable connected to the CN903
connector (the main circuit board) of the matrix
switcher.
w Connect the supplied flatcables and wirecables
to the matrix switcher's connector.
• Main circuit board
Connector # Cable type
CN904 20-pin flatcable
CN905 18-pin flatcable
CN11 7-pin wirecable
CN12 50-pin flatcable
• Sub circuit board
Connector # Cable type
CN77 6-pin wirecable
CN81 8-pin flat cable
e Fasten the Multiplexer board inside the matrix
switcher with 5 supplied screws, spring washers
and flat washers.
Note: Aim the cable clamp toward the rear
panel side.
r Connect the matrix switcher and multiplexer
board with the proper cables.
• Relationship of connectors
Matrix switcher Multiplexer board
CN11 (main) CN1004
CN81 (sub) CN1003
CN904 (main) CN1002
CN905 (main) CN1001
CN12 (main) CN103
CN77 (sub) CN101
5. Clamp the wirecable.
Cable clamp
Screws (x 5)
Spring washer
Flat washer
Cooling fan
CN903
q-1
Pull up
q-2
Disconnect
q-3
Push down
<Contact side>
<Insulation side>
Clamp (x2)
-5-
■ Connection with WJ-HD100 Series or Time-lapse VCR
• More than one camera images can be displayed in multiscreen segments on the desired monitor.
• With the Multiplexer board, the recorded images of Camera 1 to 16 can be multiplexed to Digital Disk Recorder WJ-HD
100 Series or a time-lapse VCR.
• For details, refer to the matrix switcher’s operating instructions.
Digital Disk Recorder WJ-HD100 Series or Time-Lapse VCR
Camera
16
Camera1Camera
2
Camera
3
Max. 16
Camera Inputs
16 Alarm Inputs
Multiplexer Board
WJ-SXB151
Max. 4 System Controllers 4 Monitor Outputs
Available for surveillance or playback of the camera images
WJ-SX150 Matrix Switcher
Matrix Switcher WJ-SX
OPERATE
For Matrix Switcher (WJ-SX150)
System Controller
For Matrix Switcher (WJ-SX150)
System Controller
For Matrix Switcher (WJ-SX150)
System Controller
For Matrix Switcher (WJ-SX150)
System Controller
OPERATE LED WILL BLINK
IF COOLING FAN MALFUNCTIONS
6. Attach the top cover the way it was.
How to connect cables to connectors
qPull up
qPull up
qPull out wConnect ePush in
•Multiplexer board : CN1002 (20-pin), CN1001 (18-pin)
wConnect
ePush down
•Matrix switcher
CN904 (20-pin)
CN905 (18-pin)
wConnect
ePush down
•Matrix switcher
CN12 (50-pin)
qPull up wConnect ePush down
•Multiplexer board : CN103 (50-pin)
qPull out wConnect ePush in
•Multiplexer board : CN1003 (8-pin)
•Matrix switcher : CN81 (8-pin)
Note: Connect the cables to the connectors straightforward. Inclined insertion
may cause a short circuit, which will result in a malfunction or trouble.
-6-
FIRMW ARE UPDATE
Note: Confirm the firmware version. (Refer to the matrix
switcher’s operating instructions.)
■ Installation of SX150 Program
Writer
Note: Refer to the matrix switcher’s operating instruc-
tions for the platform necessary for installation.
1. Connect the matrix switcher's serial port to that of
the PC with the 9-pin D-sub cable. (Refer to the
matrix switcher’s operating instructions.)
2. Insert the supplied CD-ROM into the PC.
3. Open the CD-ROM drive window.
The file is located in the following directory.
E: WJ-SXB151P/PWriter/SetupPWriter.exe (E is the
CD-ROM drive.)
4. Double-click the “SetupPWriter.exe” icon to begin
the installation. The Welcome window will appear on
the PC screen.
5. Press the NEXT button to continue the installation.
6. Respond to the dialog boxes by following the directions given.
7. After the installation, conform the communication
speed (SERIAL PORT SPEED) in SETUP MENU or
SX150 Admin Console to that of the PC. (Refer to
the matrix switcher’s operating instructions.)
■ Firmware Update of SX150
Program Writer
1. Launch SX150 Program Writer by selecting “Start” –
“Programs” – “Panasonic” – “SX150 Program
Writer”. The RS232C Setting window will appear on
the PC screen.
2. Confirm whether the following are selected.
Baud Rate: 38400 (Select the usable communication-port number of the PC.)
Data Bit: 8
Parity: NONE
Stop Bit: 1
Com Port: 1 (Select the usable communication-port
number of the PC.)
3. Click the SET button. The Program Writer for SX150
window will appear on the PC screen.
4. Power off the matrix switcher.
5. Set the mode selector of the matrix switcher as follows.
MODE
1ON234
Loading...