Panasonic WJ-SX650 User Manual

OPERATE

Matrix Switcher

Operating Instructions

Model Nos. WJ-SX650 Series

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

ENGLISH VERSION

Caution:

Before attempting to operate this product, please read the label on the surface of the unit.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magni-

SA 1965

SA 1966

tude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Power disconnection. Unit with or without ON-OFF switches have power supplied to the unit whenever the power cord is inserted into the power source; however, the unit is operational only when the ON-OFF switch is in the ON position. The power cord is the main power disconnect for all units.

For Canada

This Class A digital apparatus complies with Canadian ICES-003.

For U.S.A

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Caution: To assure continued compliance, (example use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

The serial number of this product may be found on the surface of the unit. You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft.

Model No.

Serial No.

WARNING:

• This apparatus must be earthed.

• To prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture.

• The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8) Do not use near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not misuse the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being stepped on or pinched particularly at plugs, convenient receptacles and the points where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-overs.

S3125A

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS ............................ 3

LIMITATION OF LIABILITY ................................................ 5

DISCLAIMER OF WARRANTY .......................................... 5

TRADEMARKS AND REGISTERED TRADEMARKS ........ 5

PRECAUTIONS .................................................................. 6

ABOUT THESE OPERATING INSTRUCTIONS ................ 7

PREFACE ........................................................................... 8

FEATURES ......................................................................... 8

MAJOR OPERATING CONTROLS AND

THEIR FUNCTIONS ........................................................... 9

■ WJ-SX650 Matrix Switcher/

WJ-SX650U Card Cage ................................................ 9

■ Video Input Board WJ-PB65C32 ................................ 11

■ Video Output Board WJ-PB65M16 ............................. 12

■ Monitor Display Information ........................................ 13

■ System Controller Display Information ....................... 14

INSTALLATIONS ............................................................. 16

■ Checking Board Composition ..................................... 16

■ Switch Settings for Video Input Main Board ............... 17

■ Switch Settings for Video Output Main Board ............. 18

■ Mounting Video Input and Output Boards ................... 19

■ Board Mounting Procedure ......................................... 20

■ Installing the Main Unit ............................................... 21

CONNECTIONS ............................................................... 22

■ Basic System Connections ......................................... 23

■ Expanded System Connections .................................. 24

■ Card Cage Connections ............................................. 26

■ Camera Connections .................................................. 27

■ RS-485 Camera Connections ..................................... 27

■ Monitor Connections ................................................... 29

■ PC Connection ............................................................ 29

■ Recorder Connection .................................................. 30

■ Recorder Settings ....................................................... 34

■ System Controller Connection .................................... 34

■ Alarm Sensor Connections ......................................... 36

■ External Device Connections ...................................... 36

■ System Status Check ................................................. 37

SETUP PROCEDURE ...................................................... 38

WJ-SX650 SERIES ADMINISTRATOR CONSOLE ......... 40

■ System Requirements of a PC ................................... 40

■ Installation and Uninstallation ..................................... 40

■ Starting Up .................................................................. 41

■ Window Details ........................................................... 41

■ Tooltip Details ............................................................. 42

■ Factory Default Settings of WJ-SX650 Series

Administrator Console ................................................ 45

SETUP MENU (OSD) ....................................................... 48

■ Basic Operations ........................................................ 48

■ TIME & DATE ............................................................. 49

■ ALARM ....................................................................... 49

■ RECORDER ............................................................... 50

■ SYSTEM ..................................................................... 52

■ INFORMATION ........................................................... 54

■ LANGUAGE ................................................................ 54

■ Operator Registration ................................................ 55

■ Power-on/off ............................................................... 56

■ Operation Start (Login) ............................................... 56

■ Operation End (Logout) .............................................. 56

■ Operation Start/End (Auto Login/Logout) ................... 56

MONITOR CONTROL ...................................................... 57

■ Monitor Selection ........................................................ 57

■ Monitor Lock ............................................................... 57

CAMERA CONTROL ........................................................ 58

■ Camera Selection ....................................................... 58

■ Camera Selection Recall ............................................ 58

■ Preset Position Control ............................................... 58

■ All Cameras Control .................................................... 59

RECORDER CONTROL ................................................... 60

■ Playback ..................................................................... 60

■ Manual Recording ....................................................... 60

■ Multiscreen Display ..................................................... 60

■ Search Playback ......................................................... 60

■ Playing the Latest Recorded Image ............................ 60

■ Recorder Control End ................................................. 61

■ Recorder Selection ..................................................... 61

RUNNING SEQUENCE .................................................... 62

■ Descriptions of Sequence ........................................... 62

■ Tour Sequence ........................................................... 64

■ Group Sequence/Preset ............................................. 64

■ Sequence Pause ........................................................ 65

■ Sequence Stop ........................................................... 65

ALARM DESCRIPTIONS ................................................. 66

■ Alarm Occurrence ....................................................... 66

■ Alarm Modes ............................................................... 67

■ Video Loss .................................................................. 67

ALARM CONTROL ........................................................... 68

■ Alarm Acknowledgement (ACK) ................................. 68

■ Camera Control .......................................................... 68

■ Alarm Picture Change ................................................. 68

■ Alarm Individual Reset ................................................ 68

■ Alarm Monitor Reset ................................................... 68

■ Alarm All Reset ........................................................... 68

■ Return to Alarm Mode Status ..................................... 69

■ Alarm Suspension ....................................................... 69

■ Alarm History Display ................................................. 69

TIMER DESCRIPTIONS ................................................... 71

■ Timer Event ................................................................ 71

■ Camera Event ............................................................. 71

TERMINAL MODE OPERATION ...................................... 73

■ Lists of Operations and Functions .............................. 73

■ Menu Flow (WV-CU950/650) ...................................... 84

OPERATION (OTHER THAN TERMINAL MODE) ........... 85

■ PS·Data Mode Operations .......................................... 85

■ Connections of Matrix Switchers (WJ-SX650 Series)

and a PS·Data System Controller ............................... 86

■ Controlling from a Web Browser Accessing a

Recorder ..................................................................... 86

■ Controlling from a PC ................................................. 86

GLOSSARY ...................................................................... 87

TROUBLESHOOTING ...................................................... 89

■ Matrix Switcher WJ-SX650 Series............................... 89

■ WJ-SX650 Series Administrator Console .................... 93

■ Power Cord, Connectors, and Power Plug ................. 94

SPECIFICATIONS ............................................................ 95

STANDARD ACCESSORIES ........................................... 97

LIMITATION OF LIABILITY

THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THE THIRD PARTY’S RIGHT.

DISCLAIMER OF WARRANTY

IN NO EVENT SHALL MATSUSHITA ELECTRIC INDUSTRIAL CO., LTD. BE LIABLE TO ANY PARTY OR ANY PERSON, EXCEPT FOR CERTAIN WARRANTY PROGRAM OFFERED BY THE LOCAL DEALER OF PANASONIC, FOR THE CASES INCLUDING BUT NOT LIMITED TO BELOW:

(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIM-

ITATION, DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT;

(2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY

INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER;

THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).

(3) UNAUTHORIZED DISASSEMBLY, REPAIR OR MODIFI-

CATION OF THE PRODUCT BY THE USER;

(4) INCONVENIENCE OR ANY LOSS ARISING WHEN

IMAGES ARE NOT DISPLAYED, DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;

(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE,

OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;

TRADEMARKS AND REGISTERED TRADEMARKS

•Microsoft, Windows and Windows XP are registered trademarks of Microsoft Corporation in the U.S. and/or other countries.

•Intel and Pentium are registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.

•Other company names and product names appearing in this document are registered trademarks or trademarks of the company concerned.

PRECAUTIONS

• Refer all work related to the installation of this apparatus to qualified service personnel or system installers.

• Do not block the ventilation opening or slots on the cover.

To prevent the apparatus from overheating, place it at least 5 cm {2 inches} away from the wall.

• Do not drop metallic parts through slots.

This could permanently damage the apparatus. Turn the power off immediately and contact qualified service personnel for service.

• Do not attempt to disassemble the apparatus.

To prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside. Contact qualified service personnel for maintenance.

• Do not strike or give a strong shock to the unit.

It may cause damage or allow water to enter the unit.

• Do not expose the apparatus to water or moisture. Do not try to operate it in wet areas.

Take immediate action if the apparatus gets wet. Turn the power off and refer servicing to qualified service personnel. Moisture can damage the apparatus and also cause electric shocks.

• Built-in backup battery

Before the first use, charge the built-in backup battery (lithium battery) by turning on the power for 48 hours or more. If it is not charged enough, in a case where the power goes down, the internal clock may keep bad time or the operative condition may be different to that before the electric power failure. The built-in battery life is approximately 5 years as an indication of replacement. (This is just an indication of replacement. We are not providing any guarantee of the built-in battery lifetime. Replacement cost of the built-in battery is not covered by the warranty even if it needs to be done within the warranty period.) Ask the shop where you purchased the unit when replacement of the battery is required.

•Cleaning

Turn the power off when cleaning the unit. Otherwise it may cause injuries. Do not use strong or abrasive detergents when cleaning the apparatus body. Use a dry cloth to clean the apparatus when it is dirty. When the dirt is hard to remove, use a mild detergent and wipe gently.

• Do not operate the apparatus beyond its specified temperature, humidity, or power source ratings.

Use the apparatus under conditions where temperatures are between –10 °C and + 50 °C {14 °F to 122 °F}, and humidity below 90 %. The apparatus may be not linked to a network after turning on in a cold atmosphere between –10 °C and 0 °C {14 °F to 32 °F}. Wait approximately 10 minutes until the inside temperature has risen to 0 °C {32 °F}, it can be linked to a network. The input power source for this apparatus is 120 V AC, 60 Hz.

•Place the unit horizontally on a level surface. Do not place the unit in an upright position. When stacking multiple units, clear a space of more than 5 cm {2 inches} from both sides, the top, the bottom and the rear of the units.

• Pay attention to static electricity

Make certain to keep boards inside the anti-static sack until it is installed. Put your hand on a metallic surface, other than the boards to discharge static electricity before installation. Do not touch components mounted on the boards directly by hand. Hold only both edges of the boards when installing.

• Do not use any power cord other than the one supplied.

• Only use the apparatus indoors.

Do not install it in places where the apparatus is exposed to sunlight for long periods of time or near air conditioning equipment. This will cause deformation, discoloration, breakdown or malfunction.

•Cooling Fan

Turn the power off when cleaning the unit. Otherwise it may cause injuries. The cooling fan will operate for approximately 30 000 hours. Replacement costs of the cooling fan are not covered by the warranty even if it needs to be done within the warranty period.

•We recommend that you make a note of your settings and save them. This will help when you are required to change the system configuration, or when unexpected trouble or failure occurs.

•Distributing, copying, disassembling, reverse compiling, reverse engineering, and also exporting in violation of export laws of the software provided with this product, is expressly prohibited.

ABOUT THESE OPERATING INSTRUCTIONS

These operating instructions are classified roughly as follows:

• Operations (pages xx, xx, xx and xx)

Contains how to operate the system. These descriptions are intended for operators. Note: Before operation, be sure to read safety instruc-

tions on p. 3 IMPORTANT SAFETY INSTRUCTIONS and p. xx PRECAUTIONS.

•Preparations (pages xx, xx, xx and xx)

Contains the required preparations including installation, connections, and setup procedures. These descriptions are intended for installers and system administrators.

Classification of digital disk recorders are as follows.

Term

WJ-HD300 Series

Model Nos.

WJ-HD316, WJ-HD309

This document uses the following terms for classification of devices.

The (This ) unit: Matrix Switcher WJ-SX650 Video input board: Video Input Board WJ-PB65C32 Video output board: Video Output Board WJ-PB65M16 Recorder: Digital Disk Recorder WJ-HD300/WJ-HD300

A Series

Remarks on Model Nos.

Begins with "WJ-HD316".

WJ-HD300A Series

WJ-HD316A, WJ-HD309A

Begins with "WJ-HD316A".

PREFACE

Matrix Switcher WJ-SX650 Series (or SX650 Series) are designed for a surveillance control system. WJ-SX650 Series (or SX650 Series) is the general term of following models.

Matrix Switcher WJ-SX650 (Video Input Board WJPB65C32 x 1 and Video Output Board WJ-PB65M16 x 1 have been installed.) Card Cage WJ-SX650U (For additional installation of video input boards and video output boards)

Video Input Board WJ-PB65C32 Video Output Board WJ-PB65M16 Expansion Cable Kit WJ-CA65L20K/WJ-CA65L07K D-sub/BNC Video Cable WJ-CA68

FEATURES

• Up to 256 cameras, 32 monitors connectable

• Remote control of optional external devices

If you connect System Controller WV-CU950, WVCU650, WV-CU360C and/or WV-CU360CJ to this product, remote control of cameras, lenses, pan/tilt heads, and recorders (Digital Disk Recorder*) will be available. * Refer to p. xx for details on model numbers. If you connect a personal computer (PC) to this product, control and system setup with WJ-SX650 Series Administrator Console will be available.

• Authentication by user ID's, passwords, and level settings.

User ID's and passwords are assignable to users to prevent inappropriate operations. In addition, the settings of level, camera access, and recorder access can determine available functions, cameras, and recorders for each user.

•Images of two or more cameras can be displayed on one monitor. Spot mode:

displayed on a selected monitor.

Sequence mode: Images of two or more cameras are

sequentially displayed on a desired monitor (or monitors).

A selected camera image is continuously

•Timer event and camera event can be scheduled.

Notes:

• Refer to p. 34 for details on timer event.

• Refer to p. 35 for details on camera event

•Alarm operation and alarm event can be scheduled.

Notes:

• Refer to p. 29 for details on alarm operation.

• Refer to p. 30 for details on alarm event

•With recorder connection, recorder control such as recording and playback are available.

Camera images can be recorded. Recorded images can be played back. Camera images can be displayed in multiscreen segments.

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

Matrix Switcher WJ-SX

OPERATE

OPERATE LED WILL BLINK

IF COOLING FAN MALFUNCTIONS

PULL

POWER

OFF

RESET

No.

MODE

RESET

TEST

MODE

Normally, do not touch. (Reserved for service personnel)

650650

■ WJ-SX650 Matrix Switcher/WJ-SX650U Card Cage

● Front View

This is the illustration of WJ-SX650.

q Operation Indicator (OPERATE)

• This indicator is lighting while power is supplied to the unit.

• This indicator blinks when the cooling fan has a trouble. (Refer to p. 96.)

w Front Panel Fixing Screws

Before you press the power switch or install boards into the expansion slot, these screw are removed to detach the front panel

e Power Switch

r Expansion Slot

Optional video input or output main board is installed. (Video Input Board WJ-PB65C32 or Video Output Board WJ-PB65M16) For WJ-SX650U, optional video input main board is installed. (Video Input Board WJ-PB65C32)

t Video Input Board*

This is a video input main board. This board controls cameras and alarm input devices (alarm sensor, etc).

Note: Refer to p. 14 WJ-PB65C32 Video Input Board for

details.

y Video Output Board*

This is a video output main board. This board controls monitors and alarm output signals.

Note: Refer to p. 15 WJ-PB65M16 Video Output Board

for details.

* For WJ-SX650U, t and y are expansion slots.

● Rear View

VIDEO OUT 3

VIDEO OUT 4

VIDEO OUT 2

MODEMODEMODEMODE

IN X-2

IN X-1

VIDEO OUT 1

ALARM IN

163215

31 30

14 13

29 28

12 11

27 26

10 9

CAMERA IN

23 22

19 18

DATA

EXTENSION 1

TERM.

OFF

OUT

OUT X-3

OUT X-2

OUT X-1

1234

AC IN

12345678

MONITOR OUT

910111213141516

ALARM OUT 2

ALARM OUT 1

SERIAL

VS OUT

VS IN

VS OUT (THRU)

EXTENSION 3 IN

EXTENSION 2 IN

MODE

RS485 (CAMERA) RS485 (CAMERA)

MODE MODE MODE

IN C-3

MODE

RS485 (CAMERA) RS485 (CAMERA)

MODE MODE MODE

IN B-3

TERM.OFF

MODE

TERM.ON

MODE

SIGNAL GND

DATA 4

HDR4/TMNL8

HDR2/TMNL4

DATA 3

HDR3/TMNL7

HDR1/TMNL3

DATA 2

TMNL6

TMNL2

DATA 1

TMNL5

TMNL1/PS DATA

Video Output Board 2

Video Output Board 1

SIGNAL GND

Video Output Board 1 Only

4-Line

RS485(CAMERA) SET UP

MODE

4-Line

MODE

AC IN

EXTENSION 3 IN

EXTENSION 2 IN

MODE

RS485 (CAMERA) RS485 (CAMERA)

MODE MODE MODE

IN C-3

SIGNAL GND

4-Line

RS485(CAMERA) SET UP

MODE

4-Line

MODE

RS485 (CAMERA) RS485 (CAMERA)

MODE MODE MODE

IN B-3

EXTENSION 3 OUT EXTENSION 2 OUT

EXTENSION 1

TERM.

OFF

OUT

MODE

RS485 (CAMERA) RS485 (CAMERA)

MODE MODE MODE

IN A-3

<WJ-SX650>

<WJ-SX650U>

!0 i!0

u Video Input Board Rear Panels*

These are video input rear boards.

Notes:

• Refer to p. 14 WJ-PB65C32 Video Input Board for details.

•When installing a set of video output board into the expansion slot, you will remove the IN B-3 board, and install the OUT B-3 board.

i Expansion Slot

Optional video input or output rear boards are installed. (Video Input Board WJ-PB65C32 or Video Output Board WJ-PB65M16) For WJ-SX650U, optional video input rear boards are installed. (Video Input Board WJ-PB65C32)

o Video Output Board Rear Panels

These are video output rear boards.

Note: Refer to p. 15 WJ-PB65M16 Video Output Board

for details.

!0 AC Inlet Socket (AC IN)

When using the unit, you will plug the power cord (supplied as a standard accessory) into this socket and connect the cord to an AC outlet.

!1 Signal Ground Terminal (SIGNAL GND)

RESET

No.

MODE

qwe

VIDEO OUT 3

VIDEO OUT 4

VIDEO OUT 2

IN X-2

VIDEO OUT 1

ALARM IN

IN X-1

163215

31 30

14 13

29 28

12 11

27 26

10 9

CAMERA IN

23 22

21 20

19 18

EXTENSION 3 IN

EXTENSION 2 IN

MODE

RS485 (CAMERA) RS485 (CAMERA)

MODE MODE MODE

IN C-3

IN C-3 board

IN X-2 board

IN X-1 board

MODE

RS485 (CAMERA) RS485 (CAMERA)

MODE MODE MODE

IN B-3

MODE

RS485 (CAMERA) RS485 (CAMERA)

MODE MODE MODE

EXTENSION 1

TERM.

OFF

OUT

IN A-3

EXTENSION 3 OUT

EXTENSION 2 OUT

IN A-3 board

IN B-3 board

tuur

■ Video Input Board WJ-PB65C32

Video input board is composed of a main board (installed into the front side) and rear boards (x 3)(installed into the rear side).

● Front View

q Board Number Switch (No.)

Refer to p. 51 Board Number Switch Settings for details.

w Input Mode Selection Switches (MODE)

Set all switches to OFF.

● Rear View

e Reset Switch (RESET)

This button is pressed to reset this board.

Note: In normal operation, you need not press the but-

ton.

IN A-3/IN B-3/IN C-3 board

Note: These boards are originally installed into WJ-SX650

and WJ-SX650U. (Not supplied to optional video input

r Extension Ports 1 (EXTENSION 1: IN, OUT)

t Termination Selector (TERM: ON, OFF)

y Extension Ports 2, 3 (EXTENSION 2, 3: IN, OUT)

u RS-485 Camera Ports 1 to 4 (RS485 (CAMERA) 1 to

boards)

These ports connect to an optional card cage.

Turns on or off the line termination of r.

Each port connects to an optional card cage.

These ports connect to RS-485 cameras.

i RS-485 Camera Mode Switches 1 to 4 (MODE 1 to 4)

These switches are moved to change the communication modes of

IN X-2 board

o Video Output Ports 1 to 4 (VIDEO OUT 1 to 4)

These ports loop through video input signals supplied to

!1.

!0 Alarm Input Port (ALARM IN)

Connects to an alarm input device (alarm sensor, door switch, etc.).

IN-3 board

!1 Camera Input Connectors 1 to 32 (CAMERA IN 1 to

32)

These connectors accept video input signals from cameras or recorders.

■ Video Output Board WJ-PB65M16

RESET

TEST

MODE

qwe

OUT X-2

12345678

MONITOR OUT

910111213141516

EXTENSION 1

TERM.

OFF

OUT

OUT X-3

MODEMODE

DATA

MODEMODE

DATA

TERM.OFF

MODE

TERM.ON

MODE

DATA 4

HDR4/TMNL8

HDR2/TMNL4

DATA 3

HDR3/TMNL7

HDR1/TMNL3

DATA 2

TMNL6

TMNL2

DATA 1

TMNL5

TMNL1/PS DATA

Video Output Board 2

Video Output Board 1

OUT X-1

ALARM OUT 2

ALARM OUT 1

SERIAL

VS OUT

VS IN

VS OUT (THRU)

Video Output Board 1 Only

ryu

i o

!1 !3

!4!2

OUT X-3 board

OUT X-2 board

OUT X-1 board

Video output board is composed of a main board (installed into the front side) and rear boards (x 3)(installed into the rear side).

● Front View

q Output Mode Selection Switches (MODE)

Refer to p. 52 Switch Settings for Video Output Board (Main Board) for details.

w Reset Switch (RESET)

This button is pressed to reset the whole system. (Equivalent to power off and on)

● Rear View

e Test port (TEST)

This port is used only for factory tests. Do not connect anything.

OUT X-3 board

r Extension Ports 1 (EXTENSION 1: IN, OUT)

t Termination Selector (TERM: ON, OFF)

y Data ports 1, 2 (DATA 1, 2)

u Data ports 3, 4 (DATA 3, 4)

i Rear Termination MODE Switches 1 to 4 (MODE 1 to

These ports connect to an optional card cage.

Turns on or off the line termination of r.

Each port connects to system controllers.

Each port connects to system controllers or recorders.

Turns on or off the line termination of y and u.

OUT X-2 board

o Monitor Output Connectors (MONITOR OUT 1 to 16)

These connectors connect to monitors.

OUT X-1 board

!0 Alarm Output Ports 1,2 (ALARM OUT 1, 2)

• Supplies alarm output signals.

• Accepts alarm recover input signals.

• Supplies and accepts the time adjust input and output signals.

!1 VS Input Connector (VS IN)

Accepts a VS input signal from an external device.

!2 VS Output Loop-thru Connector (VS OUT (THRU))

Loops through VS input signals supplied to !1.

!3 VS Output Connector (VS OUT)

Supplies VS output signals to external devices. While !1 is accepting a VS input signal, !3 supplies an output signal synchronizing the VS input signal. While accepting the VS input signal, synchronization output signal.

!3 supplies an internal

!1 is not

!4 Serial Port (SERIAL)

Connects to a PC.

Note: When q is set as Video Output Board 2, r, !1,

!2, !3, and !4 are not available.

■ Monitor Display Information

The following are the details on terminal mode operations. For PS·Data operations, refer to p. 48 OPERATION (OTHER THAN THE TERMINAL MODE) or the operating instructions of system controllers.

w e

q Time and Date Information

Current time and date are displayed. During daylight saving time (summer time), " played beside the time.

Example: Aug/02/2005 ∗20:15:56 Note: While a recorder is being selected, time and date

are not displayed.

w Monitor Status Information

Monitor number

M01 to 32: Monitor number

Note: During monitor lock, monitor number is highlight-

ed.

Controller number

Displays a device that selects and controls the monitor. K1-1 to 8-4: Terminal mode system controller

(Example: For K8-4, "8" means the terminal (TMNL) number and "4" means the controller number of system controller.)

PSD: PS·Data mode system controller PC: PC connected to the SERIAL port /T001 to 128: Timer event

Sequence number

Displays the active sequence number.

T01 to 32: Tour sequence number G01 to 32: Group sequence number

Note: During sequence pause, "P" is displayed beside

the sequence number.

∗" is dis-

e Camera Information

Camera number

C001 to 999: Camera number R01 to 16: Recorder number

Camera title

Displays the registered camera title. Camera title setting is performed in "Camera" – "Camera Title" of WJ-SX650 Series Administrator Console.

r Event Information

TERMINAL001 to 256: Terminal alarm has occurred.

(Example: For TERMINAL001, "001" means the number of alarm input signal accepted by the ALARM IN port of video input board.)

CAMERA001 to 099: Camera alarm has occurred.

(Example: For CAMERA001, "001" means the number of camera supplying an alarm input signal to the unit.)

RECORDER001 to 999: Recorder alarm has occurred.

(Example: For RECORDER001, "001" means the

number of camera associated with the recorder supplying an alarm input signal to the unit.)

SERIAL0001 to 1024: Serial alarm has occurred.

(Example: For SERIAL0001, "0001" means the serial

command alarm input number.) VIDEO LOSS001 to 999: Video loss has occurred. (Example: For VIDEO LOSS001, "001" means the num-

ber of camera to which video loss has occurred)

SUSPEND: Alarm is suspended.

Notes:

• During the alarm acknowledgement (ACK) status (refer to p. 31), event information is highlighted.

•When two or more alarm events have occurred, " displayed beside the event.

•When an alarm occurs and its display mode setting is OFF (refer to p. 30), "#" is displayed beside the event information.

•When auto tracking is scheduled for a camera event, "#" is displayed beside the camera number.

•

q to r can be displayed or hidden either altogether or separately. Refer to p. 36 Lists of Functions and Operations for details.

∗" is

■ System Controller Display Information

The following are the details on terminal mode operations. For PS·Data operations, refer to p. 48 OPERATION (OTHER THAN THE TERMINAL MODE) or the operating instructions of system controllers.

r Busy

Busy + monitor number (Blinking)

A selected monitor is controlled by a higher-level operator. (Monitor busy) Note: You cannot control the selected monitor, camera,

and recorder.

Busy + camera/recorder number (Blinking)

A selected camera or recorder is controlled by a higher-level user. (Camera/Recorder busy) Note: You cannot control the selected camera or

recorder.

t Status

Alarm (Blinking): Alarm is occurring. Alarm (Lighting): Alarm is acknowledged. (Refer to p.

31.)

Memory + preset position number (Blinking for 3.0 sec-

onds):

Preset position is registered.

y Sequence Number

T-Seq01 to 32: Tour sequence number G-Seq01 to 08: Group sequence number

Note: During sequence pause, "P" is displayed beside

the sequence number.

● WV-CU950/650

qw e

tyr

q Monitor Number

Mon01 to 32: Monitor number

w Camera Number

Cam001 to 999: Camera number C-P0001 to 9999: Camera position number

e Event

HDR01 to 16: Recorder number Pre000 to 256 (Lighting for 3.0 seconds): Preset position

Note: Pre000 is the home position.

T-A0001 to 0256: Terminal alarm C-A0001 to 0999: Camera alarm R-A0001 to 0999: Recorder alarm S-A0001 to 1024: Serial alarm V-A0001 to 0999: Video loss

G-Seq09 to 32: Group preset number

Note: This sign disappears when the camera is con-

trolled.

Invalid (Blinking for 3.0 seconds): You have entered a

wrong value.

Not Avail (Blinking for 3.0 seconds):

• You cannot select a monitor because of lower priority.

• You have tried to activate a group sequence or group preset on a monitor not assigned.

Prohibited (Blinking for 3.0 seconds): You have tried an

operation restricted by the level setting.

Alarm Buzzer/Button Buzzer Setting

With the setting activated:

•Alarm buzzer can sound when alarms occur.

• Button buzzer can sound when a button is pressed or an error message (Invalid, Prohibited, Level1 Fixed, etc.) is displayed on the LCD. Refer to the operating instructions of system controller for settings.

● WV-CU360C/CJ

MONITOR CAMERA

q Monitor number

01 to 32: Monitor number

w Camera/recorder/sequence number

001 to 999: Camera number H01 to 16: Recorder number t01 to 32: Tour sequence number r01 to r08: Group sequence number

Note: During sequence pause, "P" is displayed instead

of "t" and "r".

BUSY PROHIBITED

When the PROHIBITED indicator is lighting:

• You have entered a wrong value.

• You have tried to activate a group sequence or group preset on a monitor not assigned.

• You have tried an operation restricted by the level setting.

r09 to 32: Group preset number Note: This sign disappears when you control a camera.

e Event

The following signs appear to indicate events on the LCD.

A0001 to 0256 (Blinking): Terminal alarm A0001 to 0999 (Blinking): Camera alarm A0001 to 0999 (Blinking): Recorder alarm A0001 to 1024 (Blinking): Serial alarm A0001 to 0999 (Blinking): Video loss

Note: During the alarm acknowledgement (ACK) status

(refer to p. 31), these signs change to steady light.

Pt000 to 256 (Lighting for 3.0 seconds): Preset position Note: Pre000 is the home position.

Pr001 to 256 (Lighting for 3.0 seconds): Preset position

is registered.

r Indicators

When the MONITOR and BUSY indicators are light-

ing:

A selected monitor is controlled by a higher-

level user. (Monitor busy)

Note: You cannot control the selected monitor, camera,

and recorder.

When the CAMERA and BUSY indicators are light-

ing:

A selected camera or recorder is controlled by

a higher-level user. (Camera/Recorder busy)

Note: You cannot control the selected camera or

recorder.

INSTALLATIONS

WARNING

The installations described in the figures should be made by qualified service personnel or system installers.

The following is the installation flow of this unit.

• Checking Board Composition

• Switch Settings for Video Input Main Board (Refer to p. 51.)

• Switch Settings for Video Input Main Board (Refer to p. 52.)

• Mounting video input and output boards (Refer to p. 53.)

•Installing the main unit (Refer to p. xx.)

■ Checking Board Composition

By mounting additional video input and output boards, up to 256 cameras and 32 monitors can be connected to this unit. You will choose one of the composition types described in the following diagram. Check how many video input boards, video output boars, and card cages are required, according to the number of cameras and monitors.

Note: Refer to p. 53 for the figures describing the composition types.

Total numbers of cameras and recorders

1 to 32

33 to 64 1 to 16 100Type 3

65 to 96 1 to 16 201Type 5

97 to 128 1 to 16 301Type 7

129 to 160 1 to 16 401Type 9

161 to 192 1 to 16 502Type 11

193 to 224 1 to 16 602Type 13

225 to 256 1 to 16 702Type 15

Notes:

•When using 9 or more recorders, 2 sets of additional video output board are required even if you use 16 or less monitors.

• External monitors directly connected to recorders can be excluded from the total number of monitor in the diagram.

•When connecting monitors directly to recorders, the total numbers of these recorders can be excluded from "Total number of cameras and recorders" in the diagram.

•Use the following models for system expansion.

Video input board: WJ-PB65C32

Total number of monitors

1 to 16 000Type 1

17 to 32 010Type 2

17 to 32 111Type 4

17 to 32 311Type 6

17 to 32 311Type 8

17 to 32 4 1 2 Type 10

17 to 32 6 1 2 Type 12

17 to 32 6 1 2 Type 14

17 to 32 7 1 3 Type 16

Total set number of video input board

Total set number of video output board

Video output board: WJ-PB65M16 Card Cage: WJ-SX650U

• To connect Card Cage WJ-SX650U, Expansion Cable Kit WJ-CA65L07K (Option) or WJ-CA65L20K (Option) is required.

• To record camera images by using a recorder, Dsub/BNC Video Cable WJ-CA68 (Option) is required.

• The maximum set numbers of additional boards are as follows.

Video input board: Max. 7 sets Video output board: Max. 1 sets

Board sets exceeding these total numbers cannot be mounted even some expansion slots are unused.

Total number of card cage

Composition type (Refer to p. 53.)

■ Switch Settings for Video Input Main Board

With the switch settings of main boards, board numbers are given to all video input boards. To give the board number to each board, rotate the Unit No. switch on the main board.

No.

RESET

MODE

Board number switch

Notes:

• The board number setting must be different from each other.

•"8", "9", and "A" to "F" are reserved settings. They cannot be set for board numbers.

Board number Switch setting

■ Switch Settings for Video Output Main Board

OFF

12345 6 7 8

OFF

12345 6 7 8

When mounting an additional video input board, up to 32 monitors can be connected to the unit.

SW1, SW2, SW3, SW4

1 2

SW4006

HOST

FUNC

Front view of video output main board

TEST

RESET

MODE

12345 6 7 8

OFF

MODE switches

To identify Video Output Board 1 from Video Output Board 2, set the MODE switches (SW4004) and sliding switches (SW1, SW2, SW3, SW4, and SW4006) as follows.

SW1, SW2, SW3, SW4

SW4006

SW4004

Video Output Board 1 (Monitor 1 to 16)

HOST

Video Output Board 2 (Monitor 17 to 32)

FUNC

Note: If the unit has only one Video Output Board, be sure to apply switch settings of Video Output Board 1. When the switch

settings are incorrect, the unit may not work properly.

■ Mounting Video Input and Output Boards

Type 1

Not used

Video Input Board 1

Video Output Board 1

Type 2

Video Input Board 1

Video Output Board 2

Video Output Board 1

Type 3

Video Input Board 2

Video Input Board 1

Video Output Board 1

Type 4

Not used

Video Input Board 2

Video Input Board 1

Video Output Board 2

Video Output Board 1

Type 5 Type 6 Type 7 Type 8

Video Input Board 4

Video Input Board 3

Video Input Board 2

Video Input Board 1

Video Output Board 2

Video Output Board 1

Not used

Video Input Board 3

Video Input Board 2

Video Input Board 1

Video Output Board 1

Not used

Video Input Board 3

Video Input Board 2

Video Input Board 1

Video Output Board 2

Video Output Board 1

Not used

Video Input Board 4

Video Input Board 3

Video Input Board 2

Video Input Board 1

Video Output Board 1

Type 9 Type 10 Type 11 Type 12

Not used

Video Input Board 6

Video Input Board 5

Video Input Board 4

Video Input Board 3

Video Input Board 2

Video Input Board 5

Video Input Board 4

Video Input Board 3

Video Input Board 2

Video Input Board 1

Video Output Board 1

Not used

Video Input Board 5

Video Input Board 4

Video Input Board 3

Video Input Board 2

Video Input Board 5

Video Input Board 4

Video Input Board 3

Video Input Board 1

Video Output Board 2

Video Output Board 1

Video Input Board 1

Video Output Board 2

Video Output Board 1

Video Input Board 2

Video Input Board 1

Video Output Board 1

Not used

Video Input Board 6

Type 13 Type 14 Type 15 Type 16

Not used

Video Input Board 8

Video Input Board 7

Video Input Board 6

Video Input Board 5

Video Input Board 6

Video Input Board 7

Video Input Board 4

Video Input Board 3

Video Input Board 2

Video Input Board 6

Video Input Board 7

Video Input Board 8

Video Input Board 5

Video Input Board 4

Video Input Board 3

Video Input Board 4

Video Input Board 3

Video Input Board 2

Video Input Board 1

Video Output Board 2

Video Output Board 1

Video Input Board 1

Video Output Board 2

Video Output Board 1

Not used

Video Input Board 7

Video Input Board 6

Video Input Board 5

Video Input Board 4

Video Input Board 3

Video Input Board 2

Video Input Board 1

Video Output Board 1

Video Input Board 2

Video Input Board 1

To use additional video input or output boards, mount these boards into the expansion slots of the unit after checking the board composition and performing switch settings (refer to p. 50 to 53). The following is the figures describing recommended board composition.

Notes:

• Refer to p. 54 for how to mount these boards.

•Video Output Board 1 and 2 must be mounted into the same unit.

• Refer to p. 59 for how to connect card cages.

■ Board Mounting Procedure

The following is the procedure to mount a set of video input or output board into the expansion slot of the unit.

Note: Before the procedure, power off the unit.

1. Remove the expansion slot panel from the rear side.

A N G

I S

D N G

N G I

N O . M R E

T F F

M R E T

T A D

D O M

T A D

A T A D

P /

L M

1 T /

H D H

p t u

B t u p t

u O o

e d i

2. Mount the rear boards (x 3) into the expansion slot, and fix these boards with screws supplied to the rear boards.

3. Remove the front panel by loosening the screws.

OPERATE

4. Mount the main board by hooking the board stoppers on the board stopper angles at the front side, and by pushing down the board stoppers.

G L A

N G I S

N G L

N G I

N O

. M R E

T F F

N O . O

M R E T

O M

A T A D

D O M

5 L

T A D

T A D S

/ 1

L N

T /

1 T /

H D H

4 L N

M d r

/ a

R B t

p t u O

1 o e

r d i

o B

t u p t u O

o e d i

IN X-2 board

IN X-1 board

Notes:

• The board name (IN X-1, OUT X-1, etc.) is marked at the lower right corner of each board mounting angle. When mounting the rear boards, match the board names with the markings at board mounting angles.

• To mount a set of video input board into the expansion slot, dismount the IN B-3 board, and then mount the OUT X-3.

Notes:

• Remove 3 screws surely at the arrow marking when dis-

mounting.

•When mounting, match the main board surely with the rear board.

•When mounting, insert the main board surely into slits.

•Do not hit the boards against the chassis of the unit.

■ Installing the Main Unit

Places to avoid

•Places exposed to direct sunlight or near a source of heat such as a radiator

• Very dirty and dusty places

•Places subject to strong vibrations

•Near magnetic field sources such as a television or speakers

•Near high-voltage cables such as a power cable

•Near noise sources such as fluorescent lamps

•Places where condensation forms easily

• Humid places

•Places where drastic temperature changes occur

•Places which are not level

•Steamy and oily places such as kitchens

3. Mount the unit into the rack by fixing the rack mounting screws (locally procured: 8 pcs). (Refer to the following illustration.)

EIA 19 inch rack

Rack Mounting

When mounting this unit, use the following racks.

Standard Rack: WU-RS71 (29 units can be mounted.) Long Rack: WU-RL76 (41 units can be mounted.) EIA equivalents (Products of other manufacturers): EIA

19 inch rack, 450 mm {17-7/10"} or more depth

Note: When mounting this unit into a rack of another manu-

facturer, Rack Mounting Screw (W2-MSS/5008) (Option) or M5 x 12 screws (4 pcs.) are required. If you use the supplied rack mounting screws (nominal diameter 5 tapping), the screw heads may be damaged.

1. Power off the unit.

2. Remove the rubber feet (4 psc.) on the bottom of the unit by loosening the screws.

Make a space equivalent to

approx. 1 unit (44 mm) or more

650

Important:

• If the rack is subject to vibration, secure the rear of the unit to the rack by using additional mounting brackets (locally procured).

• To avoid loosening, secure the mounting screws surely.

•When operating the units, keep the temperature inside the rack surely below 45 °C {113 °F}.

•Mount the unit into the rack with a space equivalent to approx. 1 unit (44 mm) or more to separate from other devices.

•Mounting ventilation fan(s) in the rack is recommended especially when the rack is covered with front lids.

• To prevent the unit from overheating, do not block the ventilation openings or slots in the cover

Remove the rubber feet.

CONNECTIONS

Important:

Use only the recommended BNC connectors listed below.

RECOMMENDED Tip dimensioins inside the BNC

ﬂ 1.32 mm — ﬂ 1.37 mm

Tip

(inside)

ﬂ 0.13 mm — ﬂ 0.69 mm

Standards

BNC

Video (coaxial) Cable

For U.S.A.

For Europe

For Japan

Suffixes attached to the standards may be updated.

Other BNC connectors may cause video signal interruption, and damage the BNC receptacles on the rear panel of the unit.

MIL-C39012C or MIL-C39012/16F

BS CECC 22120:1981

JIS C5412

■ Basic System Connections

Video input board

Expansion slot

Video output board

A B

SYSTEM CONTROLLER

A B

SYSTEM CONTROLLER

SERIAL

DATA

CAMERA IN

MONITOR OUT

Recorder

PC (WJ-SX650 Series Administrator Console)

78ON612345

78612345

78ON612345

Camera 1 to 30

Monitor 1 to 16

VIDEO OUT (Loop-thru output)

(#7: ON) (#8: OFF)

(#7: OFF) (#8: OFF)

MODE switches

WV-CU950/650

WV-CU360C/CJ

Te rm i nal mode, Line termination: ON

The following is a connection example to use one unit.

This unit x 1, camera x 30, monitor x 16, and recorder x 2

■ Expanded System Connections

A B

SYSTEM CONTROLLER

A B

SYSTEM CONTROLLER

Card cage connection

CAMERA IN

VIDEO OUT (Loop-thru output)

MONITOR OUT

Recorder Recorder Recorder

Recorder Recorder

Recorder

Camera 1 to 150

Monitor 1 to 32

System controller

DATA

DATADATA

DATA

SERIAL

DATA

PC (WJ-SX650 Series Administrator Console)

Video input board

Video output board

The following is a connection example to use two or more units.

This unit x 3, camera x 150, monitor x 32, and recorder x 10

This unit x 4, camera x 240, monitor x 32, and recorder x 15

Recorder Recorder Recorder Recorder

Recorder Recorder Recorder

Card cage connection

Video input board

Video output board

A B

SYSTEM CONTROLLER

A B

SYSTEM CONTROLLER

DATA

DATADATA

DATA

SERIAL

DATA

DATADATA

DATA

Camera 1 to 240

Monitor 1 to 32

System controller

PC (WJ-SX650 Series Administrator Console)

VIDEO OUT (Loop-thru output)

CAMERA IN

MONITOR OUT

■ Card Cage Connections

AC IN

SIGNAL GND

4-Line

RS485(CAMERA) SET UP

MODE

4-Line

MODE

EXTENSION 3 IN

EXTENSION 2 IN

MODE

RS485 (CAMERA) RS485 (CAMERA)

MODE MODE MODE

IN C-3

VIDEO OUT 3

VIDEO OUT 4

VIDEO OUT 2

IN X-2

VIDEO OUT 1

ALARM IN

MODE

RS485 (CAMERA) RS485 (CAMERA)

MODE MODE MODE

IN B-3

EXTENSION 1

TERM.

OFF

OUT

IN A-3

MODEMODE

DATA (TMNL/PS·DATA)

MODEMODE

DATA (TMNL/HDR)

EXTENSION 3 OUT EXTENSION 2 OUT

IN X-1

163215

31 30

14 13

29 28

12 11

27 26

10 9

CAMERA IN

23 22

21 20

19 18

VIDEO OUT 3

VIDEO OUT 4

VIDEO OUT 2

IN X-2

VIDEO OUT 1

ALARM IN

IN X-1

163215

31 30

14 13

29 28

12 11

27 26

10 9

CAMERA IN

23 22

21 20

19 18

AC IN

SIGNAL GND

4-Line

RS485(CAMERA) SET UP

MODE

4-Line

MODE

EXTENSION 3 IN

EXTENSION 2 IN

MODE

RS485 (CAMERA) RS485 (CAMERA)

MODE MODE MODE

IN C-3

VIDEO OUT 3

VIDEO OUT 4

VIDEO OUT 2

IN X-2

VIDEO OUT 1

ALARM IN

MODE

RS485 (CAMERA) RS485 (CAMERA)

MODE MODE MODE

IN B-3

EXTENSION 1

TERM.

OFF

OUT

IN A-3

MODEMODE

DATA (TMNL/PS·DATA)

MODEMODE

DATA (TMNL/HDR)

EXTENSION 3 OUT EXTENSION 2 OUT

IN X-1

163215

31 30

14 13

29 28

12 11

27 26

10 9

CAMERA IN

23 22

21 20

19 18

VIDEO OUT 3

VIDEO OUT 4

VIDEO OUT 2

IN X-2

VIDEO OUT 1

ALARM IN

IN X-1

163215

31 30

14 13

29 28

12 11

27 26

10 9

CAMERA IN

23 22

21 20

19 18

AC IN

SIGNAL GND

4-Line

RS485(CAMERA) SET UP

MODE

4-Line

MODE

VIDEO OUT 3

VIDEO OUT 4

VIDEO OUT 2

IN X-2

VIDEO OUT 1

ALARM IN

EXTENSION 3 IN

EXTENSION 2 IN

MODE

RS485 (CAMERA) RS485 (CAMERA)

MODE MODE MODE

IN C-3

MODEMODEMODEMODE

DATA (TMNL/HDR)

DATA (TMNL/PS·DATA)

EXTENSION 1

TERM.

OFF

OUT

OUT X-3

1234

TERM.ON

MODE

TERM.OFF

MODE

DATA 4

HDR4/TMNL8

HDR2/TMNL4

DATA 3

HDR3/TMNL7

HDR1/TMNL3

DATA 2

TMNL6

TMNL2

DATA 1

TMNL5

TMNL1/PS DATA

Video Output Board 2

Video Output Board 1

OUT X-2

12345678

MONITOR OUT

910111213141516

OUT X-1

ALARM OUT 2

ALARM OUT 1

SERIAL

VS OUT

VS IN

VS OUT (THRU)

Video Output Board 1 Only

MODEMODEMODEMODE

DATA (TMNL/HDR)

DATA (TMNL/PS·DATA)

EXTENSION 1

TERM.

OFF

OUT

OUT X-3

1234

TERM.ON

MODE

TERM.OFF

MODE

DATA 4

HDR4/TMNL8

HDR2/TMNL4

DATA 3

HDR3/TMNL7

HDR1/TMNL3

DATA 2

TMNL6

TMNL2

DATA 1

TMNL5

TMNL1/PS DATA

Video Output Board 2

Video Output Board 1

OUT X-2

12345678

MONITOR OUT

910111213141516

OUT X-1

ALARM OUT 2

ALARM OUT 1

SERIAL

VS OUT

VS IN

VS OUT (THRU)

Video Output Board 1 Only

IN X-1

16 15 14 13 12 11 10 9

CAMERA IN

87654321

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17

VIDEO OUT 3

VIDEO OUT 4

VIDEO OUT 2

IN X-2

VIDEO OUT 1

ALARM IN

IN X-1

163215

31 30

14 13

29 28

12 11

27 26

10 9

CAMERA IN

23 22

21 20

19 18

VIDEO OUT 3

VIDEO OUT 4

VIDEO OUT 2

IN X-2

VIDEO OUT 1

ALARM IN

IN X-1

163215

31 30

14 13

29 28

12 11

27 26

10 9

CAMERA IN

23 22

21 20

19 18

Line termination: ON at the connection end

Line termination: OFF

Line termination: ON at the connection end

Expansion Cable Kit WJ-CA65L20K or WJ-CA65L07K

Card Cage WJ-SX650U is used for mounting additional Video Input Board WJ-PB65C32. Up to 3 video input boards can be mounted into a card cage.

The following is a connection example to use additional card cages.

•Maximum unit connections: Matrix Switcher WJ-SX650 x 1, Card Cage WJ-SX650U x 3.

•Video Output Board 1 and 2 must be mounted into the same unit.

•Unit that has video output boards must be at the connection end.

•When connecting the EXTENSION 1 to 3 ports of each unit, use Expansion Cable Kit WJ-CA65L20K (Option) or WJCA65L07K (Option).

• Connect nothing to the EXTENSION 1 port of the Video Output Board 2.

■ Camera Connections

The following is a connection example to use system cameras and combination cameras.

Notes:

•Make sure that the cable length is less than 900 m {3 000 ft} between the camera site and the unit when using RG-59/U, BELDEN 9259 or equivalent cables.

• To display recorded images on monitors connected to this unit, connect the MONITOR OUT connectors of recorders to the CAMERA IN connectors of the unit.

•When connecting cameras to the unit, reserve more unused connectors than the recorder total number. (Refer to p. 63 Recorder Connections for details.)

18193132

1516

1234

Combination

camera

System camera

21 20

ALARM IN

19 18

IN C-3

IN X-2

IN X-1

EXTENSION 3 IN

VIDEO OUT 4

163215

31 30

14 13

VIDEO OUT 3

29 28

12 11

EXTENSION 2 IN

27 26

VIDEO OUT 2

10 9

CAMERA IN

MODE

RS485 (CAMERA) RS485 (CAMERA)

MODE MODE MODE

VIDEO OUT 1

23 22

Video input rear board

■ RS-485 Camera Connections

There are two options to connect RS-485 cameras to this unit.

•1:1 connection: One camera is connected to one RS-485 (CAMERA) port.

• Daisy chain connection: Up to 8 cameras can be connected to one RS-485 (CAMERA) port.

Notes:

• Set the line termination to ON for cameras at the connection ends. Line termination setting is performed with the MODE 1 to 4 switches (refer to p. 61) at video input rear boards.

• Perform the RS-485 camera setting in RS485 CAMERA of SETUP MENU (refer to p. 84) or "System" – "RS485 Camera" of WJ-SX650 Series Administrator Console.

•1 200 m {3 937 ft} is the total length limit of RS-485 cables.

• Recommended for RS-485 communication is AWG#22 or thicker one. The cable should be shielded, two-wire, twisted pair, and with low impedance.

• Conform the 2-wire or 4-wire communication setting of this unit to that of RS-485 cameras.

The following is the details on MODE 1 to 4 switch settings.

1234

OFF

communication

4-wire

1234

2-wire communication Line termination: ON

4-wire communication Line termination: OFF

2-wire

communication

1234

● 1:1 Connection

One camera is connected to one RS-485 (CAMERA) port.

Example: RS-485 cameras are connected to the CAMERA IN 9 and 12 connectors.

Connector

RS485 (CAMERA) 1 RS485 (CAMERA) 2

4-wire

communication

1234

(SW#4: ON) (SW#1 to 4: ON)

MODE switch settings

2-wire

communication

1234

Unit number: 1 Line termination: ON

EXTENSION 3 IN

VIDEO OUT 4

163215

31 30

14 13

VIDEO OUT 3

29 28

12 11

EXTENSION 2 IN

27 26

VIDEO OUT 2

10 9

CAMERA IN

Junction Unit WV-CA48/JN

Unit number: 1 Line termination: ON

MODE

RS485 (CAMERA) RS485 (CAMERA)

MODE MODE MODE

VIDEO OUT 1

23 22

21 20

Video input rear boards

Note:

Do not use unit numbers other than 1 to 8 for individual cameras.

● Daisy Chain Connection

Two or more cameras can be connected to one RS-485 (CAMERA) port. Up to 8 cameras are available.

RS-485 cable

ALARM IN

19 18

IN C-3

IN X-2

IN X-1

Example: RS-485 cameras are connected to the CAMERA IN 9 to 12 connectors

Daisy Chain Connection Kit WV-CA48/10K

Junction Unit WV-CA48/JN

RS-485 cable

Connector

RS485 (CAMERA) 1

4-wire

communication

1234

(SW#4: ON) (SW#1 to 4: ON)

2-wire

communication

1234

MODE switch settings

Unit number: 4 Line termination: ON

EXTENSION 3 IN

VIDEO OUT 4

163215

31 30

14 13

Unit number: 3 Line termination: OFF

EXTENSION 2 IN

VIDEO OUT 3

29 28

27 26

12 11

Unit number: 2 Line termination: OFF

RS485 (CAMERA) RS485 (CAMERA)

MODE

VIDEO OUT 2

10 9

CAMERA IN

Unit number: 1 Line termination: OFF

23 22

MODE MODE MODE

VIDEO OUT 1

21 20

ALARM IN

19 18

IN C-3

IN X-2

IN X-1

Video input rear boards

Notes:

•Among cameras connected to an RS485 (CAMERA) port in the daisy chain (4-wire communication), only one camera can activate camera alarms.

•Do not use unit numbers other than 1 to 8 for individual cameras.

• Do not set the same unit numbers for more than one camera in an RS-485 chain.

■ Monitor Connections

• The MONITOR OUT 1 to 16 connectors of Video Output Board 1 are assigned to Monitor 1 to 16.

• The MONITOR OUT 1 to 16 connectors of Video Output Board 2 are assigned to Monitor 17 to 32.

Video Output Board 2

Video Output Board 1

DATA 4

HDR4/TMNL8

HDR2/TMNL4

DATA 3

HDR3/TMNL7

HDR1/TMNL3

DATA 2

TMNL6

TMNL2

ALARM OUT 2

DATA 1

TMNL5

TMNL1/PS DATA

TERM.ON

MODE

TERM.OFF

Video output rear boards

MODE

910111213141516

MONITOR OUT

ALARM OUT 1

DATA

VS OUT

DATA

SERIAL

MODEMODE

EXTENSION 1

OUT

Video Output Board 1 Only

MODEMODE

VS IN

VS OUT (THRU)

OFF

OUT X-3

TERM.

12345678

OUT X-2

OUT X-1

■ PC Connection

Refer to Serial (RS-232C) Connector Command Reference (PDF file on the supplied CD-ROM) for details on the connection and communication settings.

PC (WJ-SX650 Series Administrator Console)

9-pin D-sub

(Female)

VS OUT

DATA

SERIAL

MODEMODE

EXTENSION 1

OUT

Video Output Board 1 Only

OFF

TERM.

OUT X-3

OUT X-2

OUT X-1

12345678

Video Output Board 2

Video Output Board 1

DATA 4

HDR4/TMNL8

HDR2/TMNL4

DATA 3

HDR3/TMNL7

HDR1/TMNL3

DATA 2

TMNL6

TMNL2

ALARM OUT 2

DATA 1

TERM.ON

TMNL5

TMNL1/PS DATA

MODE

Video output rear boards

TERM.OFF

MODE

910111213141516

MONITOR OUT

ALARM OUT 1

DATA

MODEMODE

VS IN

VS OUT (THRU)

■ Recorder Connection

The following is a connection example to use recorders.

Note: Use recorders with the following versions.

•WJ-HD300 Series: Ver. 1.61 or later

•WJ-HD300A Series: Ver. 3.10 or later

● Connection to Video Output Connectors of Recorders

To display recorder images on monitors connected to this unit

When the video output connectors of recorders are connected to CAMERA IN connectors of this unit, recorder images can be displayed on Monitor 1 to 32. The following is the connection procedure.

1. Assign unit addresses to the recorders. (Refer to p. 67 q.) Available unit addresses are 1 to 16. The unit address setting must be different from each other.

2. Decide the video input board to supply video input signals from recorder. Choose a video input board that has more unused connectors (CAMERA IN 17 to 32) than the recorder total number.

Note: Only one video input board can be connected to the video output connector of recorders.

3. Connect the video output connectors (the monitor output 2 connector) of recorders and the CAMERA IN 17 to 32 connectors of the unit.

Recorder's unit address

8251617

Note:

To supply video input signals from recorders to video input boards, perform the settings surely in RECORDER of SETUP

MENU (refer to p. 87) or "System" – "Recorder" of WJ-SX650 Series Administrator Console.

CAMERA IN channel of video input board

32 9 24

31 10 23

30 11 22

29 12 21

28 13 20

27 14 19

26 15 18

Recorder's unit address CAMERA IN channel of

video input board

+ 68 hidden pages