Panasonic WJ-PB65E01E User Manual

Model No. WJ-PB65E01E
V
id
e
o
O
u
u
t B
o
a
r
d
1
O
n
ly
N
e
w
o
rk
O
U
T
X
-1
A
L
A
R
M
O
U
T
1
A
L
A
R
M
O
U
T
2
1
0
0
0
B
A
S
E
-
T
Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
Trademarks and Registered Trademarks
Network Board
Operating Instructions
• Microsoft and Windows are either registered trade­marks or trademarks of Microsoft Corporation in the United States and/or other countries.
• Intel and Pentium are trademarks or registered trade­marks of Intel Corporation or its subsidiaries in the United States and other countries.
Precautions
CAUTION: These servicing instructions are for use by qual-
ified service personnel only. To reduce the risk of elec­tric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
• Do not attempt to disassemble the apparatus.
To prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside. Contact qualified service personnel for maintenance.
• Other names of companies and products contained in these operating instructions may be trademarks or reg­istered trademarks of their respective owners.
• Do not strike or give a strong shock to the appara­tus.
It may cause damage or allow water to enter the appa­ratus.
• Pay attention to static electricity
Make certain to keep boards inside the anti-static sack until it is installed. Put your hand on a metallic surface, other than the boards to discharge static electricity before installation. Do not touch components mounted on the boards directly by hand. Hold only both edges of the boards when installing.
References
Along with this document, refer to Central Processing Unit WJ-MPU955A Operating Instructions for major operating
Preface
Network Board WJ-PB65E01E is designed for the connection with Central Processing Unit WJ-MPU955A and system
controls, their functions, and switch settings.
expansion of Matrix Switcher WJ-SX650 Series.
Features
• With this board, the network connection between Central Processing Unit WJ-MPU955A and Matrix Switcher WJ-SX650 Series becomes available to expand the system composition. Up to 512 cameras and 64 monitors become connectable.
Major Operating Controls and Their Functions
Front View
e
10/100 BASE-T
q r yt
ALARM OUT 2
w
q Ethernet Port (10/100BASE-T)
This port is used for connection with Central Processing Unit WJ-MPU955A via an Ethernet network. LINK indicator: This indicator lights up when the matrix
switcher is linked to a network through this port.
ACT indicator: This indicator lights up when the matrix
switcher receives or sends data through this port.
LINK indicator
ACT indicator
ALARM OUT 1
VS IN
VS OUT (THRU)
VS OUT
SERIAL
Video Output Board 1 Only
e VS Input Connector (VS IN)
Accepts a VS input signal from an external device.
r VS Output Loop-thru Connector (VS OUT (THRU))
Loops through VS input signals supplied to e.
t VS Output Connector (VS OUT)
Supplies VS output signals to external devices. While e is accepting a VS input signal, t supplies an output signal synchronizing the VS input signal. While e is not accepting the VS input signal, t supplies an internal synchronization output signal.
y Serial Port (SERIAL)
Connects to a PC.
NETWORK OUT X-1
w Alarm Output Ports 1, 2 (ALARM OUT 1, 2)
Supplies alarm output signals controlled by Central Processing Unit WJ-MPU955A. Note: Refer to WJ-SX650 Series Operating Instructions
for the ALARM OUT port details. (Pin Nos. 3, 5, 7, 9, 12, 14, 16, 18, 36, and 37 are unavailable.)
2
Board Mounting Procedure
The following example is the procedure to mount a network board into the OUT X-1 slot of WJ-SX650 Series.
Notes:
• This network board can be inserted into the OUT X-1 slot only.
• Before the procedure, power off WJ-SX650 Series.
• Remove the screws and fixing brackets surely when dismounting.
• Fix the screws surely when mounting.
• Do not hit the boards against the chassis of WJ-SX650 Series.
1. Remove the front panel by loosening the screws.
O
P
E
R
A
T E
M
a
tr
ix
S
w
itc
h
e
r
W
J
-
S
X
650
4. Mount the network board into the OUT X-1 slot, and fix the board with the supplied screws.
SIGNAL GND
D
N G L
A N
G
I
N O
. M R E T
F F
N
O
O
. M R E T
E D O M
TA 1 DA
E
D O M
L5
A 2
MN T
DAT
A
T A D S
6
P /
A 3
NL
1 L
M
N
AT
T
M
D
T
7
2
NL
L
MN
/TM
A 4
T
DR3
DAT
H
NL3
L8
TM
/TMN
R1/
HD DR4 H
L4
2
MN
rd
2/T
oa
DR H
tput B u O
rd 1
Video
tput Boa Ou eo
Vid
S
Network board
5. Mount the video output main board by hooking the board stoppers on the board stopper angles at the front side, by pushing down the board stoppers, and by fix­ing the screws. Then, attach the front panel.
2. Dismount the video output main board from the front side.
Video output main board
Fixing brackets (x4)
Screws (x8)
3. Dismount the OUT X-1 board from the rear side.
D
N
G L A
N
IG
S
Board stopper angle
Board stopper
Hook the board stoppers on the board stopper angles, and push down the board stoppers.
Fixing brackets (x4)
Screws (x8)
Mount the main board into the slot.
Fix the board with the screws (x3).
Attach the fixing brackets (x4) with the screws (x8).
Note: When mounting, insert the main board surely into
slits.
D N G
L A N
G I
TERM.ON FF ON
TERM.O
1
MODE
A T A D
MODE
5
L
2
N
A
M
T
T
A D
A
T A D S
6 L
P
3
/
A
N
1 L
T
M
N
A
T
M
D
T 7 L
2
N
L
M
N
4
M
/T
A
3
T
T
R
A
D
D
H
3 L
8
N
L
M
N
/T
M
1
/T
R
4
D
R
H D H
4 L
N
2
M d r
/T
a
2
o
R
t B
D
u
H
tp u O
1
o
d
e
r d i
a
o
V
t B u
tp u O o e
d i V
S
OUT X-1 board
Fixing brackets (x2)
Screws (x2)
3
Loading...
+ 5 hidden pages