Panasonic VVX32H101G00 Specification

Global LCD Panel Exchange Center

The following specifications are applied to the following IPS-Pro-TFT LCD module.

www.panelook.com

DESCRIPTION

Product Name :

Product Factory : Panasonic Liquid Crystal Display Co.,Ltd. (Mobara/Utsunomiya/Himeji, Japan)

Panasonic Liquid Crystal Display Czech,s.r.o. (Czech Republic)

Panasonic Liquid Crystal Display Malaysia Sdn.Bhd. (Malaysia)

Effective display area : (H) 697.685 × (V) 392.256 (mm)

Number of pixels : (H) 1,366 × (V) 768 (pixels)

Pixel pitch : (H) 0.51075 × (V) 0.51075 (mm)

Color pixel arrangement : R+G+B vertical stripe

Display mode : Transmissive mode

Normally black mode

Top polarizer type : Semi-Glare

VVX32H101G00

General Specifications

Number of colors :16,777,216 (colors)

Viewing angle range : wide version

(Horizontal & Vertical : 178° at =0°,90°,180°,270°, CR㻢10䋩

Input signal : mini LVDS (LVDS : Low voltage differential signaling)

Backlight : 72 tips of LED (LED: Light-emiting diode)

External dimensions : Typ. (H) 735.4 × (V) 433.0 × (t) 37.0 (mm)

Weight : Typ. (6,000) (g)

Panasonic Liquid Crystal Display Co.,Ltd.

Date May.10,2011 Sheet No. IPS4PS 3-1/1

VVX32H101G00-5

2603

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Page

www.panelook.com

Global LCD Panel Exchange Center

1. ABSOLUTE MAXIMUM RATINGS

1. 1 Environmental Absolute Maximum Ratings

ITEM

Temperature 0 50 -20 60

Humidity 2)

Vibration -

Shock -

Corrosive Gas

Illumination at

LCD Surface

Note 1) Temperature and Humidity should be applied to the glass surface of a IPS-Pro TFT LCD module, not to

the system installed with a module.

2) Ta҇40 Relative humidity should be less than 85 %RH max. Dew is prohibited.
Ta㧪40 Relative humidity should be lower than the moisture of the 85 %RH at 40 .

Min. Max.

Not Acceptable

- 50,000 - 50,000 1x

Operating

www.panelook.com

4.9(0.5 G)

29.4(3 G)

Storage

Min. Max.

2) 㧑RH

-

-

294(30 G)

Not Acceptable -

UNIT



m/s

m/s

NOTE

1),5),6)

1)

2

2

3)14.7(1.5 G)

4)

Relative Humidity(%RH)

100

80

60

Operating range

40

20

0

Storage range

20 40 60 800-20-40

Temperature(㷄)

3) Frequency of the vibration is between 15 Hz and 100 Hz. (Remove the resonance point) 1 hour.

4) Direction : ±X, ±Y, ±Z (One time each direction)

5) Pulse width of the shock is 10 ms.

6) The temperature of LCD front surface would be 65 㷄 in operating, it may affect the optical characteristics

however it does not damage the function of the module.

Panasonic Liquid Crystal Display Co.,Ltd.

Date

May.10,2011 Sheet No.

IPS4PS 4-1/2Page

VVX32H101G00-5

2604

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

1. 2 Electrical Absolute Maximum Ratings

(1)TFT-LCD module VSS = 0 V

ITEM SYMBOL Min.

Source Driver Analog Power Supply AVDD 0 V16.0

Driver Logic Power Supply VDD 0 4.0 V

Gate Driver Power Supply

Gate Driver Ground VOFF

Gamma Corrected Power Supply VREF1䌾6 0.4AVDD AVDD+0.3

Gamma Corrected Power Supply

Common Plate Power Supply

Input Voltage for logic

Electrostatic Durability

www.panelook.com

Max. UNIT NOTE

VON 0

VON-VOFF 0 44

-20 0.3

VREF8䌾12 -0.3 0.6AVDD V

VCOM VCOMaj - 2.0 VCOMaj + 2.0 V 5)

1 -0.3

V

V

2 -0.3

V

3 -0.3 7

ESD0 ±100 V

V

ESD1 ±20 kV

V

37

VDD + 0.3

VDD + 1.2

V

V

V

V

V1)

V6)

7)

2),3)

2),4)

Note 1) It is applied to pixel data signal, clock signal and other control signals.

2) Discharge Coefficient : 250 pF - 100 , Environmental : 25 㷄 - 70䋦RH

3) It is applied to I/F connector pins.

4) It is applied to the surface of a metallic bezel and a LCD panel.

5) VCOMaj means adjusted VCOM voltage.

6) It is applied to SDA, SCL signal.

7) It is applied to WP signal.

(2) Backlight unit

ITEM SYMBOL

Temperature Junction of LED Tj

Max. UNITVNOTE

㪈㪇㪇
㪎㪉㪇

㷄

㫄㪘

Note 1) The specification shall be applied to each LED.

2) The specification shall be applied at connector pins for LED at start-up.

1)

2)Forward Current If

Panasonic Liquid Crystal Display Co.,Ltd.

Date May.10,2011 Sheet No. IPS4PS

VVX32H101G00-5

2604

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

4-2/2Page

www.panelook.com

Global LCD Panel Exchange Center

X

2. INITIAL OPTICAL CHARACTERISTICS

The following optical characteristics are measured under stable conditions. It takes about 30 minutes to reach stable

conditions. The measuring point is the center of display area unless otherwise noted.

The optical characteristics should be measured in a dark room or equivalent state.

Measuring equipment : CS-1000A, or equivalent
Ambient Temperature =25  , V

I

L=12mArms (on duty 100%)

ITEM SYMBOL CONDITION Min. Typ. Max. UNIT NOTE

Contrast ratio

Response

time

Rise t

Fall t

Brightness of white B

Brightness uniformity B

Red

Color

Green

chromaticity

㧔CIE㧕

Blue

White

Red

Variation of

Green

color position

(CIE)

Blue

White

Contrast ratio at 89 ° CR89

%4

on -

off

wh 350 450 -

uni --40

x 0.560 0.590 0.620

[

x 0.310 0.340 0.370

[

x 0.125 0.155 0.185

[

x 0.250 0.280 0.310

[

x

y

x

y

x

ޓޓ180 °,

y - - 0.04

x - - 0.04

y - - 0.04

www.panelook.com

DD=12.0 V , f V=60 Hz ,

㧩 0 °

1)

㧩 50 °

㧩 0 °,

ޓޓ 90 °,

ޓޓ270 °

1)

=0°,90°,
180°,270°

6)

0.305 0.335 0.365

0.570 0.600 0.630 -

0.035 0.065 0.095

0.253 0.283 0.313

800

-8

1400 - - 2)

10 20 ms

20 ms

cd/m

㧑

2

3)

3)

4)

ޣGray scale

=255ޤ

- - 0.04

- - 0.04

- - 0.04

- - 0.04 -

- - 0.04

5)

䇼Gray scale

=255䇽

10 - - - Estimated value

Note 1) Definition of viewing angle

=180°

(9 o'clock)

X'

TFT - LCD module

Panasonic Liquid Crystal Display Co.,Ltd.

Mosaic

pattern

=90°
(12 o'clock)

Y

=0°

Z



Z'

Date May.10,2011 Sheet No.

Invisible

-7)Image sticking -

eye



=0°

(3 o'clock)

Y'

=270°

(6 o'clock)

VVX32H101G00-5

IPS4PS 5-1/2Page

2605

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

f

K

K

Note 2) Definition of contrast ratio (CR)

(Luminance at displaying WHITE)

CR=

(Luminance at displaying BLACK)

3) Definition of response time

Displaying

data signal

%

100

Optical

response

(Luminance)

4) Definition of brightness uniformity

Display pattern is white (255 level) . The brightness uniformity is defined as the following equation.

Brightness at each point is measured, and average, maximum and minimum brightness is calculated.

uni=

B

where, B

B

B

5) Variation of color position on CIE

Variation of color position on CIE is defined as difference between colors at = 0° and at = 50°& = 0°,

90°, 180°, 270°.

6) Contrast ratio at 89 °

Evaluetion conditions are on horizontal & vertical axis

7) Image sticking

Condition : Operating mosaic pattern for 2 hours and gray scale ( 22 % ) for 1 hour.

90

10

max = Maximum brightness

min = Minimum brightness

ave = Average brightness

BLAC

0

max or Bmin - Bave

B

Bave

B

ave=

k=1

www.panelook.com

WHITE

ton tof

×100

9

(B(k))



䋹

Mosaic pattern

BLAC

10%

50%

90%

10% 50% 90%

: measuring points

100%

0%

Panasonic Liquid Crystal Display Co.,Ltd.

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Date May.10,2011 Sheet No. IPS4PS 5-2/2Page

VVX32H101G00-5

2605

www.panelook.com

Global LCD Panel Exchange Center

3. ELECTRICAL CHARACTERISTICS

3. 1 TFT-LCD module Ta = 25  , GND = 0 V

ITEM SYMBOL

Source Driver Analog
Power Supply Voltage

Ripple voltage of AVDD Vrip_avdd

Driver Logic Power Supply Voltage VDD 2.4 2.5

Ripple voltage of VDD Vrip_vdd

Gate Driver Power Supply Voltage VON 29.0

Ripple voltage of VON Vrip_von

Gate Driver Ground Voltage VOFF -6.35 -5.8

Ripple voltage of VOFF

Input High Voltage for logic

Input Low Voltage for logic VIL1 -

Input High Voltage for EEPROM

Input Low Voltage for EEPROM VIL2

Output Low Voltage from EEPROM VOL - - V 4)

Common Plate Voltage VCOM -

Ripple voltage of VCOM Vrip_vcom -

Source Driver Analog Power Supply Current

Driver Logic Power Supply Current IDD - 20 30 mA 1)

Gate Driver Ground Current IOFF

Gamma Corrected Power Supply Voltage 1 VREF1 - 12.033

Gamma Corrected Power Supply Voltage 2 VREF2 - 10.656 - V

Gamma Corrected Power Supply Voltage 3 VREF3 - 9.329

Gamma Corrected Power Supply Voltage 4 VREF4 - 8.690 - V

Gamma Corrected Power Supply Voltage 5 VREF5 - 8.161

Gamma Corrected Power Supply Voltage 6 VREF6 - 6.342 - V

Gamma Corrected Power Supply Voltage 8 VREF8 - 4.462

Gamma Corrected Power Supply Voltage 9 VREF9 - 3.921 - V

Gamma Corrected Power Supply Voltage 10 VREF10 - 3.257

Gamma Corrected Power Supply Voltage 11 VREF11 - 1.893 - V

Gamma Corrected Power Supply Voltage 12 VREF12 - 0.479

Ripple voltage of VREF Vrip_VREF - - 200 mV 5), 6)

Note 1)

fV=60.0Hz䋬fCLK=156MHz䋬each power supply voltage is typical condition and display pattern is white raster.

www.panelook.com

Min.

AVDD

Vrip_voff -

VIH1

VIH3

IADD

12.286

-

--

-

- - 500 mV

0.8VDD - VDD

0

0.8VDD

0.8VDD

0- 3)V0.2VDD

-

Typ.

12.586

-

-

30.5 32.5 V

-

- 5.25 V 7)

5.125 - V

- 200

150 200

-3.0 - mA 1)-5.0

Max.

12.886

350 mV

250 mV

2.6 V

150 mV

-5.25 V

200

0.2VDD

0.4

5.0

-V

-V

-V

-V

-V

-V

UNIT

V

mV 5), 6)

V

V2)

V

mV 5), 6)

mA 1)

mA 1)Gate Driver Power Supply Current ION - 3.0

NOTE

5), 6)

5), 8)

5), 6)

5), 6)

2)

3)- VDD+1.2VIH2

DC ampere meter

AVDD, VDD, VON, VOFF

TFT module

GND

2) It is applied to LP, POLR, POLL, CPV, DATA1 and DATA2 signal.

3) It is applied to SDA, SCL signal.

4) It is applied to SDA signal. IOL=1.5mA

5) The above specification is defined at connector CN1.

6) Display pattern is white raster.

7) It is applied to WP signal.

8) Display pattern is 128gray raster.

Panasonic Liquid Crystal Display Co.,Ltd.

Date May.10,2011 Sheet No. IPS4PS

VVX32H101G00-5

2606

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

6-1/2Page

www.panelook.com

Global LCD Panel Exchange Center

3. 2 Backlight unit

ITEM SYMBOL Min. Typ. Max. UNIT NOTE

Forward Currnet

(One LED Assembly)

Forward Voltage

Power Consumption

PWM

One Backlight Unit : 2 LED Array

One LED Array : 2 LED String

One LED String : 18 LED package

Note 1) This characteristics should be applied putting on the LED about 60 minutes later with ambient temperature.

( Ta = 25  ± 2  )

2) Life time of a LED is defined as follows. The life is determined as the time at which brightness of the LED

is 50 % compared to that of initial value at that typical forward current on condition of continuous operating
at 25 ± 2 㷄.

www.panelook.com

Anode

Cathode Ifc 114 120

String Vf 57.6 61.2 64.8 V

Variation Vf(unit) One BL unit (1.5) V

Duty

Frequency

Ifa 228 240 252 mA

126 mA

--

Pbl

PD

PF 95 - 182 Hz One BL unit

26.3 29.4 34.5 W

0 - 100

- h (2)LED Life time - 30000 -

%

Panasonic Liquid Crystal Display Co.,Ltd.

Date May.10,2011 Sheet No.

IPS4PS 6-2/2Page

VVX32H101G00-5

2606

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com