Panasonic VL-SWD501 User Manual
De
m
en
2
4
V
G
ge
Poo
2 Wire ><
Model No.
VL-SWD501
Video Intercom System with Wireless Monitor (DECT)
* Only for distribution in Europe, Middle East, Asia & Oceania
System Configuration
Expanded system example
Up to
5
Power
Supply Unit
Video Intercom System
VL-SWD501
Bedroom
Bedroom
Power
Supply Unit
Living Roo
Living Room
< 2 Wire >
Electric lock
DECT Repeater
The DECT Repeater can also be connected to increase usage area.
+ ++ +
Door Station
VL-PS241
L-PS241
* Up to 2 repeaters can be used.
DECT Wireless
Sub Monitor
Room 1 Room 2
Room 1 Room
Kitch
Kitchen
Den
n
・
100m
Using one repeater
・
100m 100m
Using two repeaters connected together
・
100m 100m 100m
* Signal range differs depending on factors such as the structure of rooms or the types of walls used.
・
Up to
4
DECT Wireless
Sensor Camera
VL-WD812 VL-FKD2VL-V554 VL-WD613
Room 3Room
Room 3 Room 4
Electric lock
A single repeater can be used to
send signals to either multiple sub
monitors or cameras.
A single repeater cannot be used to
send signals to both sub monitors
and cameras.
DECT Wireless
Repeater
Pool
l
Up to
2
Power
Supply Unit
Power
Supply Unit
ara
Garage
Power
Supply Unit
Wiring Schematic Diagram
DOOR STATION 1
ELECTRIC LOCK
(Electric vehicle gate lock)
ELECTRIC LOCK
(Electric door lock)
ELECTRIC LOCK
(Electric vehicle gate lock)
ELECTRIC LOCK
(Electric door lock)
NP
NP
NP
22 AWG
18 AWG
CAT 5
22 AWG
18 AWG
22 AWG
18 AWG
Rear view
NP
Rear view
Wire type
12 V AC/DC
Power
Supply
Power
Supply
Power
Supply
Power
Supply
*1
According to specification of connected device.
According to specification of connected device.
According to specification of connected device.
Must be no longer than 20 m.
D
12 V AC/DC
12 V AC/DC
D
12 V AC/DC
100 m
130 m
50 m
10 m
20 m
No requirement
50 m
100 m
No requirement
MAIN MONITOR
Rear view
A
NP
NP
B
24 V DC
220-240 V AC
C
AC
POWER SUPPLY UNIT
NP: Non-polarised
NP
E
Connection device for option output
(A contact)
DOOR STATION 2
NP
*1 Make sure to only connect electric vehicle gate locks to the S3/S4 terminals of the door stations.
(VL-SWD501EX, VL-SWD501FX models only)
*2 Make sure to only connect electric door locks to the S1/S2 terminals of the door stations.
Wire type and length
Wiring run
Main monitor – Door station
Main monitor – Power supply unit
Power supply unit – AC power source
Door station – Electric lock
Main monitor
– Connection device for option output (A contact)
*2
Wireless sensor camera – Power supply unit
Power supply unit (for wireless sensor camera)
– AC power source
Wireless sensor camera – External sensor
*1 Type: Single-pair cable with outer sheath (jacket)
Conductor: Copper solid
• A certified power supply wiring has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered.
A certified power supply wiring not lighter than ordinary polyvinyl chloride flexible wiring according to IEC 60227 shall be used.
*2 When using an electric lock or a connection device for option output (A contact), select a device that meets the following guidelines:
• Electric lock connection terminal (S1/S2, S3/S4): N/O dry closure contact
12 V AC/DC, less than 1 A
• Connection device for option output (A contact) terminal (OUT1/OUT2): 24 V AC/DC, less than 0.3 A (minimum contact: 5 V DC 1 mA)
A
B
φ 1.2 mm - φ 2.0 mm (17 AWG - 12 AWG)
C
D
φ 0.5 mm - φ 1.2 mm (24 AWG - 17 AWG)
*2
E
φ 0.5 mm - φ 1.2 mm (24 AWG - 17 AWG)
-
-
φ 1.2 mm - φ 2.0 mm (17 AWG - 12 AWG)
-
φ 0.5 mm - φ 0.8 mm (24 AWG - 20 AWG)
Diameter Length (Max.)
φ 0.65 mm
φ 1.0 mm
φ 0.5 mm
φ 0.65 mm
φ 1.0 mm
φ 0.65 mm
φ 1.0 mm
*1
*2
*1
*2
Loading...