Page 1
Video Intercom System
Flush mount unit
Installation and Operation Guide
Model No. VL-GW001A
● This product is a flush mount unit for use only with the monitor station
<VL-GM301A> and sub monitor station <VL-GM001A> for the video intercom
system. It cannot be used with any other units.
Safety Precautions (Be sure to observe the following.)
1) Do not modify.
If this is not observed, injury may result. Do not disassemble.
2) Install to a wall that is strong enough to bear the unit’s weight.
If the wall is not strong enough, the unit may fall down and injury may result.
• If the wall is not strong enough, add reinforcement to give it extra strength.
3) Install securely to the wall.
If this is not observed, the unit may fall down and injury may result.
4) Inspect at regular intervals.
If the mounting screws become loose, the unit may fall down and injury may result.
5) Do not install in places where there is lots of humidity or dust or where
the unit may be affected by oil fumes or steam.
If this is not observed, fire or electric shocks may result.
The following must be observed at all times.
Be sure to observe the following, otherwise malfunctions may result.
■ Avoid installing in the following locations
•Locations that are subject to strong shocks or vibrations.
■ When carrying out installation work
•All cables should be routed at least 30 cm (11
cables or routed in separate tubes.
•Use metal pipes if routing through areas where strong magnetic fields are present.
•None of the connection cables should be unused.
Please make sure that there is NOT any object within 20cm (8 inches) of the flush
mount unit. This may cause a communication error or malfunction of monitor station
and sub monitor station.
13
/
”) away from electric light
16
Check before installing
Embedded mounting box Makeup panel
(Check the package contents after opening.)
Small screw : 4 pcs.
4 mm x 25 mm (
3
/
16
” x 1”)
Template
Page 2
Installation
Installation
Make a hole in the wall.
1
● Install so that the monitor screen will
be at an appropriate level for the eyes
of the person using it.
Place the embedded
2
mounting box into the wall.
● Check that the embedded
mounting box is installed the
right way up.
(Check the
● Place the fixing plates inside
the embedded mounting box
(in four locations).
UP mark.)
Hole
Floor
Fixing
plate
Embedded
mounting box
Tighten the four
3
embedded
mounting box
screws to secure
the box to the wall.
● Check that the fixing
plates move outside the
embedded mounting box
to securely clamp the box
against the wall.
Remove the front case and
4
terminal cover from the bottom
case of the monitor station and
sub monitor station.
(Refer to the installation guide
provided with the video intercom
system.)
Fixing
plate
[Cross-sectional view]
Fixing
plate
Bottom case Front case
Screw
Terminal
cover
Embedded
mounting
box
Page 3
Installation
Install the bottom case to the
5
embedded mounting box with the
four small screw (4 mm x 25 mm,
3
/
” x 1”).
16
● If connecting a video cable,
connect the video cable before
installing the bottom case.
Connect the cables and then
6
attach the front case and
terminal cover.
(Refer to the installation guide
provided with the video intercom
system.)
Securely insert the tabs
7
of the makeup panel into
the slots in the embedded
mounting box.
● Check that the makeup
panel is installed the right
way up.
(Check the
● The number of makeup
panel tabs are 10 tabs.
If the tabs are not inserted
securely, there will be a gap
between the makeup panel
and the wall.
UP mark.)
small screws
(supplied)
Bottom case
Embedded mounting box
Terminal
cover
Front case
Reverse surface
of makeup panel
Embedded
mounting box
Makeup panel
Tabs
Reverse surface
of mekeup panel
Removing the Makeup panel
● Insert a flat-tipped screwdriver or similar into
the slot at the bottom of the makeup panel to
remove the makeup panel.
•Be careful not to break the makeup panel
tabs when removing the makeup panel.
Makeup panel
Page 4
General Information
Notes on installation
● Install to a wall with a thickness of approximately 5 - 20 mm (
and a total space of approximately 45 mm (1
wall thickness and the depth of the cavity.
13
”) or more including the
/
16
Embedded
mounting box
3
13
” -
/
16
”)
/
16
Makeup panel
Approximately 5-20 mm (
Approximately 45 mm (1
3
13
/
16
13
” -
/
16
”) or more
Wall
”)
/
16
● This unit is only for installing to a wall with a cavity, and so it cannot be used in
concrete walls or earthen walls.
● This model is designed for embedded installation only, so do not install it directly
to a ceiling or wall.
Specifications
Model No.
Weight : 600
: VL-GW001A
gg
g (1.32 lbs.)
gg
Outer dimensions
For your future reference
Date of purchase
Serial number (found on the rear of the unit)
Dealer’s name and address
Dealer’s telephone number
Attach your sales receipt here.
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094, U.S.A.
Panasonic Puerto Rico, Inc.
San Gabriel Industrial Park, Ave. 65 de Infantería, Km. 9.5, Carolina, Puerto Rico
00985, U.S.A.
Printed in CHINA
LHQT0199
S0305-0
Loading...