Panasonic VDR-D310PL, VDR-D230PL, VDR-D210PL Operating Instructions Manual
Operating Instructions
DVD Video Camera
Model No. VDR-D310PL
VDR-D230PL
VDR-D210PL
Before use, please read these instructions
completely.
VDR-D310 VDR-D230 VDR-D210
Video light – µ –
SD card
compatible
µµ –
Computer
software
µµ –
LSQT1150 B
LSQT1150.book 1 ページ ２００７年２月１４日 水曜日 午前１１時２０分
2
LSQT1150
Things You Should Know
Thank you for choosing Panasonic!
You have purchased one of the most
sophisticated and reliable products on the
market today. Used properly, we’re sure it will
bring you and your family years of enjoyment.
Please take time to fill in the information on the
right.
Be sure to retain this manual as your
convenient camera information source.
Safety Precautions
The following mark and symbols are located on bottom of the unit.
CAUTION:
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE,
≥ DO NOT EXPOSE THIS APPARATUS TO RAIN, MOISTURE, DRIPPING OR SPLASHING AND
THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE
APPARATUS.
≥ USE ONLY THE RECOMMENDED ACCESSORIES.
≥ DO NOT REMOVE THE COVER (OR BACK); THERE ARE NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION!
DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE, BUILT-IN CABINET OR IN
ANOTHER CONFINED SPACE. ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT RISK
OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO OVERHEATING, ENSURE THAT CURTAINS
AND ANY OTHER MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of
uninsulated “dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
CAUTION
CAUTION:
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
LSQT1150.book 2 ページ ２００７年１月１９日 金曜日 午前９時２７分
3
LSQT1150
ENGLISH
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
≥ AS WITH ANY SMALL
OBJECT, SD CARDS CAN BE
SWALLOWED BY YOUNG
CHILDREN. DO NOT ALLOW
CHILDREN TO HANDLE THE
SD CARD.
CLASS 1
LASER PRODUCT
IEC 60825-1:2001
CAUTION
This product contains a laser diode of higher class than 1. To
ensure continued safety, do not remove any covers or
attempt to gain access to the inside of the product. Refer all
servicing to qualified personnel.
FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
≥ Reorient or relocate the receiving antenna.
≥ Increase the separation between the equipment and receiver.
≥ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
≥ Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, follow the attached installation instructions and use
only shielded interface cables with ferrite core when connecting to computer or peripheral devices.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
Declaration of Conformity
Trade Name: Panasonic
Model No.: VDR-D230PL/VDR-D310PL
Responsible party: Panasonic Corporation of North America
One Panasonic Way, Secaucus, NJ 07094
Support Contact: Panasonic Consumer Electronics Company
1-800-211-PANA (7262)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1)This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
WARNING
VDR-D230PL/
VDR-D310PL
LSQT1150.book 3 ページ ２００７年１月１９日 金曜日 午前９時２７分
4
LSQT1150
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the
unit and the applicable safety instructions listed below. Keep these operating instructions handy for
future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or the table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when it will be left unused for
long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
LSQT1150.book 4 ページ ２００７年１月１９日 金曜日 午前９時２７分
5
LSQT1150
∫ Indemnity concerning recording content
The manufacturer shall in no event be liable for the loss of recordings due to malfunction or defect of
this unit, its accessories or recordable media.
IMPORTANT
∫ Carefully observe copyright laws
Whatever you have recorded and created can be used for your personal entertainment only.
Under copyright laws, other materials cannot be used without obtaining permission from the
holders of the copyrights.
Precautions
USE & LOCATION
≥ TO AVOID SHOCK HAZARD ... Your camera
and power supply should not be exposed to
rain or moisture. Do not connect the power
supply or operate your camera if it gets wet.
Your camera has been designed for outdoor
use, however it is not designed to sustain
direct exposure to water, rain, sleet, snow,
sand, dust, or a direct splashing from a pool or
even a cup of coffee. This action could
permanently damage the internal parts of your
camera. Do not attempt to disassemble this
unit. There are no user serviceable parts
inside. Unplug your camera from the power
supply before cleaning.
≥ DO NOT AIM YOUR CAMERA AT THE SUN
OR OTHER BRIGHT OBJECTS
≥ DO NOT LEAVE THE CAMERA WITH THE
EVF AIMED DIRECTLY AT THE SUN AS
THIS MAY CAUSE DAMAGE TO THE
INTERNAL PARTS OF THE EVF
≥ DO NOT EXPOSE YOUR CAMERA TO
EXTENDED HIGH TEMPERATURE ... Such
as, in direct sunlight, inside a closed car, next
to a heater, etc... This action could
permanently damage the internal parts of your
camera.
≥ AVOID SUDDEN CHANGES IN
TEMPERATURE ... If the unit is suddenly
moved from a cold place to a warm place,
moisture may form on the disc and inside the
unit.
≥ DO NOT LEAVE YOUR CAMERA OR THE
POWER SUPPLY TURNED ON WHEN NOT
IN USE.
≥ STORAGE OF YOUR CAMERA ... Store and
handle your camera in a manner that will not
subject it to unnecessary movement (avoid
shaking and striking). Your camera contains a
sensitive pick-up device which could be
damaged by improper handling or storage.
CARE
≥ TO CLEAN YOUR CAMERA ... Do not use
strong or abrasive detergents when cleaning
your camera body.
≥ TO PROTECT THE LENS ... Do not touch the
surface of the lens with your hand. Use a
commercial camera lens solution and lens
paper when cleaning the lens. Improper
cleaning can scratch the lens coating.
≥ TO PROTECT THE FINISH OF YOUR
CAMERA ... Before handling your camera,
make sure your hands and face are free from
any chemical products, such as suntan lotion,
as it may damage the finish.
WARNING
CAUTION
LSQT1150.book 5 ページ ２００７年１月１９日 金曜日 午前９時２７分
6
LSQT1150
Batteries
1 Battery pack (Lithium ion battery pack)
≥ Use the specified unit to recharge the battery pack.
≥ Do not use the battery pack with equipment other than the specified unit.
≥ Do not get dirt, sand, liquids, or other foreign matter on the terminals.
≥ Do not touch the plug terminals (i and j) with metal objects.
≥ Do not disassemble, remodel, heat or throw into fire.
2 Button-type battery (Lithium battery)
≥ Insert with poles aligned.
≥ Do not touch the terminals (i and j) with metal objects.
≥ Do not recharge, disassemble, remodel, heat or throw into fire.
≥ Keep out of reach of children
If any electrolyte should come into contact with your hands or clothes, wash it off thoroughly with
water.
If any electrolyte should come into contact with your eyes, never rub the eyes. Rinse eyes thoroughly
with water, and then consult a doctor.
Warning
Risk of fire, explosion and burns. Do not disassemble.
Do not heat the batteries above the following temperatures or incinerate.
Button-type battery 60 oC (140 oF)
Battery pack 60 oC (140 oF)
AC adaptor
This AC adaptor operates on AC between 110 V and 240 V.
But
≥ In the U.S.A. and Canada, the AC adaptor must be connected to a 120 V AC power supply only.
≥ When connecting to an AC supply outside of the U.S.A. or Canada, use a plug adaptor to suit the
AC outlet configuration.
≥ When connecting to a supply of greater than AC 125 V, ensure the cord you use is suited to the
voltage of the AC supply and the rated current of the AC adaptor.
≥ Contact an electrical parts distributor for assistance in selecting a suitable AC plug adaptor or AC
cord set.
The socket outlet shall be installed near the equipment and easily accessible. The mains plug of the
power supply cord shall remain readily operable. To completely disconnect this apparatus from the
AC Mains, disconnect the power supply cord plug from AC receptacle.
A lithium ion/polymer battery that is recyclable powers the product
you have purchased. Please call 1-800-8-BATTERY for information
on how to recycle this battery.
U.S.A. CONSUMERS: ATTENTION:
LSQT1150.book 6 ページ ２００７年１月１９日 金曜日 午前９時２７分
7
LSQT1150
-If you see this symbol-
≥ SDHC Logo is a trademark.
≥ miniSD Logo is a trademark.
≥ Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, and 4,819,098, licensed for limited
viewing.
This product incorporates copyright protection technology that is protected by method claims of
certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
≥ Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
≥ LEICA is a registered trademark of Leica microsystems IR GmbH and DICOMAR is a registered
trademark of Leica Camera AG.
≥ Microsoft
®
, Windows® and DirectX® are either registered trademarks or trademarks of the Microsoft
Corporation in the United States and/or other countries.
≥ IBM and PC/AT are registered trademarks of International Business Machines Corporation of the
U.S.
≥ Intel
®
, Intel® CoreTM Solo, Intel® CoreTM Duo and Pentium® are the registered trademarks or
trademarks of the Intel Corporation in the United States and other countries.
≥ Macintosh and Mac OS are either registered trademarks or trademarks of Apple Computer, Inc. in the
United States and/or other countries.
≥ Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
≥ Other names of systems and products mentioned in these instructions are usually the registered
trademarks or trademarks of the manufacturers who developed the system or product concerned.
These operating instructions are designed for use with models VDR-D310, VDR-D230 and VDR-D210.
Pictures may be slightly different from the original.
≥ The illustrations used in these operating instructions show model VDR-D310, however, parts of the
explanation refer to different models.
≥ Depending on the model, some functions are not available.
≥ Features may vary, so please read carefully.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and
ask for the correct method of disposal.
LSQT1150.book 7 ページ ２００７年１月１９日 金曜日 午前９時２７分
8
LSQT1150
Before using
Features ................................................10
Quick Guide..........................................12
Accessories..........................................15
Parts identification and handling .......16
Using the LCD monitor ............................. 19
Using the viewfinder .................................20
Using the remote control (VDR-D310) .....20
Discs and cards.................................... 22
Discs that can be used on this unit...........22
Cards that you can use with this unit
(VDR-D310/VDR-D230) ...........................26
Disc and card handling.............................27
Setup
Power supply........................................28
Charging the battery.................................28
Connecting to the AC outlet .....................32
Turning the unit on/off............................... 32
Inserting/removing a disc.................... 33
Inserting/removing an SD card
(VDR-D310/VDR-D230).........................35
Selecting a mode..................................36
How to use the joystick .......................36
Switching the language....................... 40
Using the menu screen........................ 40
Setting date and time...........................42
Adjusting LCD monitor/viewfinder..... 43
Recording
Before recording ..................................44
Recording motion pictures .................46
Recording modes and recordable time
available for the motion picture ................47
Recording MPEG still pictures
(VDR-D210)..............................................48
Recording still pictures
(JPEG still pictures)
(VDR-D310/VDR-D230).........................49
Number of pixels and picture quality for
still picture recording ................................52
Various recording functions ...............53
Zoom in/out function ................................ 53
Recording yourself................................... 54
Recording with the video light
(VDR-D230) ............................................. 54
Backlight compensation function ............. 55
Fade in/fade out function ......................... 55
Soft skin mode......................................... 56
Tele macro function (VDR-D310) ............. 57
MagicPix function..................................... 57
Self-timer recording
(VDR-D310/VDR-D230) ........................... 58
Recording guideline function.................... 58
Wide mode............................................... 59
Image stabilizer function .......................... 59
Wind noise reduction function.................. 59
Manual recording functions................ 60
Scene mode............................................. 60
Manual focus adjustment ......................... 61
White balance.......................................... 61
Manual shutter speed/
aperture adjustment ................................. 63
Playback
Motion picture playback...................... 65
Still picture playback
(JPEG still pictures)
(VDR-D310/VDR-D230).........................69
Editing
Editing scenes......................................71
Deleting scenes ....................................... 71
Dividing a scene....................................... 72
Combining scenes ................................... 72
Using playlists......................................73
What is a playlist?.................................... 73
Creating a new playlist ............................. 73
Playing back a playlist.............................. 74
Editing a playlist.......................................74
Editing still pictures
(VDR-D310/VDR-D230).........................78
Deleting still pictures ................................ 78
Locking still pictures ................................. 79
DPOF setting ........................................... 79
Disc and card management
Disc management ................................ 81
Finalizing a disc .......................................81
Contents
LSQT1150.book 8 ページ ２００７年１月１９日 金曜日 午前９時２７分
9
LSQT1150
Un-finalizing a DVD-RW...........................82
Protecting a disc.......................................82
Formatting discs.......................................82
Displaying disc information.......................83
Card management
(VDR-D310/VDR-D230).........................83
Formatting an SD card .............................83
With other products
With a TV...............................................85
Playback on TV........................................85
With a DVD recorder/player.................86
Playback on DVD recorder, DVD player,
computer etc.............................................86
Copying (dubbing) recordings onto a
DVD recorder’s hard disk.........................87
With a VCR............................................87
Recording (dubbing) images onto
other video devices ..................................87
With a printer (PictBridge)
(VDR-D310/VDR-D230).........................88
With a computer
(VDR-D310/VDR-D230)
Before using with a computer
(Windows).............................................91
What you can do with a computer ............91
Contents on provided CD-ROM ...............92
Operating environment.............................94
End User License Agreement ..................97
Installation (Windows) .........................97
Installing DVD-RAM Driver.......................98
Installing DVD-MovieAlbumSE .................99
Installing DVDfunSTUDIO......................100
Starting the applications .........................100
Reading the operating instructions of the
software applications .............................. 101
Software application uninstallation .........101
Connection and recognition
(Windows)...........................................102
Connection and recognition procedures
....102
About the computer display.................... 103
To disconnect USB cable safely .............104
Verifying the unit is correctly recognized
by the computer......................................104
Creating a DVD-Video disc on a
computer (Windows)..........................105
Creating a DVD-Video on a computer from
a DVD-RAM or DVD-RW (VR format)
....... 105
Before using with a computer
(Macintosh).........................................108
What you can do with a computer.......... 108
Contents on provided CD-ROM ............. 109
Operating environment .......................... 110
Installation (Macintosh) ..................... 111
Reading the operating instructions of the
software application................................111
Software application uninstallation..........111
Using discs on a computer
(Macintosh).........................................112
Creating a DVD-Video on a computer
from a recorded disc .............................. 112
To disconnect USB cable safely............. 113
Using an SD card on a computer
(Macintosh).........................................114
Connection............................................. 114
Copying still picture files to a computer
..... 114
To disconnect USB cable safely............. 115
Others
Menus..................................................116
Menu list................................................. 116
Other menus .......................................... 117
Indications .......................................... 118
Indications.............................................. 118
Messages............................................... 121
Functions that cannot be used
simultaneously ....................................... 123
Frequently asked questions.............. 124
Troubleshooting .................................127
Cautions for use.................................133
Explanation of terms.......................... 136
Specifications.....................................138
Number of recordable pictures on
an SD card (VDR-D310/VDR-D230)...... 141
Optional accessories......................... 143
Index....................................................144
LSQT1150.book 9 ページ ２００７年１月１９日 金曜日 午前９時２７分
Before using
10
LSQT1150
Before using
Features
∫ Easy recording! (l 46)
No need to search for the recording start position.
The new recording will not overwrite any previously recorded scene.
∫ Easy playback! (l 65)
Recorded scenes are displayed as thumbnails.
You can easily search for the scenes you want to watch.
∫ Editing scenes! (l 71, 73)
You can create an original video (playlist) by collecting your favorite scenes together and then easily
record (dub) this video to a VCR or a DVD recorder.
LSQT1150.book 10 ページ ２００７年１月１９日 金曜日 午前９時２７分
Before using
11
LSQT1150
∫ Using with DVD player/recorder! (l 86)
Just insert the disc into a DVD player/recorder compatible with 8 cm (3z) discs to play back the scenes
recorded with this unit.
If you have a DVD recorder with hard disk, you can copy (dub) scenes recorded on a disc with this unit
to the hard disk.
∫ Using with a computer! (VDR-D310/VDR-D230) (l 91)
You can enjoy editing scenes with the software on the supplied CD-ROM and creating original
DVD-Video discs.
If you insert a DVD-RW or a DVD-R disc recorded in this unit (that has not been finalized) into
another device such as DVD recorder, computer, etc., the disc may become unusable.
Be sure to finalize the disc on this unit before inserting it in other devices. (l 81)
LSQT1150.book 11 ページ ２００７年１月１９日 金曜日 午前９時２７分
12
LSQT1150
Before using
Quick Guide
∫ Charging the battery
1 Connect the AC cable to the AC adaptor
and the AC outlet.
2 Put the battery on the battery mount by
aligning the mark, and then securely plug
it in.
∫ Inserting the battery
Push the battery against the battery holder
and slide it until it clicks.
∫ Removing the battery
While sliding the BATTERY lever, slide the
battery to remove it.
∫ How to turn on/off the power
While pressing the button A, set the OFF/ON
switch to ON/OFF.
∫ Inserting/removing a disc
1 Slide the DISC EJECT lever once and
release it.
2 Open the cover of the disc compartment
by hand and insert/remove the disc.
3 Push the section marked PUSH CLOSE
on the cover of the disc compartment to
close the cover.
A
A
LSQT1150.book 12 ページ ２００７年１月１９日 金曜日 午前９時２７分
13
LSQT1150
Before using
∫ Inserting/removing an SD card
(VDR-D310/VDR-D230)
1 Slide the card slot cover to open.
2 Insert/remove the SD card into/from the
card slot.
3 Securely close the card slot cover.
∫ Recording motion pictures
≥ Rotate the mode dial to select .
1 Press the recording start/stop button to
start recording.
2 Press the recording start/stop button
again to pause recording.
∫ Recording still pictures (JPEG
still pictures) (VDR-D310/
VDR-D230)
≥ Rotate the mode dial to select .
VDR-D310:
1 Press the Photoshot button [ ] halfway
in order to adjust focusing. (For auto
focusing only)
LSQT1150.book 13 ページ ２００７年１月１９日 金曜日 午前９時２７分
14
LSQT1150
Before using
2 Press the Photoshot button [ ] fully to
take the picture.
VDR-D230:
Press the Photoshot button [ ].
∫ Motion picture playback
≥ Rotate the mode dial to select .
1 Select the scene to be played back.
2 Press the joystick.
3 Move the joystick to operate.
∫ Still picture playback (JPEG still
pictures) (VDR-D310/VDR-D230)
≥ Rotate the mode dial to select .
1 Select the file to be played back.
2 Press the joystick.
3 Move the joystick to operate.
1/;: Playback/Pause
:: Skip playback (backward)
9: Skip playback (forward)
∫: Stops the playback and shows the
thumbnails.
1/;: Slide show start/pause.
E: Plays back the previous picture.
D: Plays back the next picture.
LSQT1150.book 14 ページ ２００７年１月１９日 金曜日 午前９時２７分
15
LSQT1150
Before using
Accessories
Check the accessories before using this unit.
∫: Stops the playback and shows the
thumbnails.
Battery pack
(VDR-D310)
CGA-DU12
Battery pack
(VDR-D230/VDR-D210)
CGR-DU06
AC adaptor
PV-DAC14D
AC cable
K2CA2CA00029 or
K2CA2CA00025
DC cable
K2GJ2DC00011
AV/S cable
(VDR-D310/VDR-D230)
K2KZ9CB00001
AV cable
(VDR-D210)
K2KC4CB00020
Remote control
(VDR-D310)
N2QAEC000023
Button-type battery
(VDR-D310)
CR2025
Lens cap
LSYK2004
USB cable
(VDR-D310/VDR-D230)
K1HA05CD0014
CD-ROM
(VDR-D310/VDR-D230)
LSFT0713
Disc cleaning cloth
VFC3778-2
LSQT1150.book 15 ページ ２００７年２月１４日 水曜日 午前１１時２０分
16
LSQT1150
Before using
Parts identification and
handling
1 Lens (LEICA DICOMAR) (VDR-D310)
Lens (VDR-D230/VDR-D210)
2 Video light (VDR-D230) (l 54)
3 Microphone (built-in, stereo)
4 White balance sensor (l 62)
Remote control sensor (VDR-D310) (l 21)
5 Menu button [MENU] (l 40)
6 Viewfinder (l 20)
7 Delete button [ ] (l 71, 75, 78)
8 LCD monitor open part (l 19)
9 DC input terminal [DC/C.C. IN] (l 32)
10 Battery holder (l 28)
11 Power switch [OFF/ON] (l 32)
12 Status indicator (l 32)
13 Video light button [LIGHT] (VDR-D230)
(l 54)
14 Disc/computer access lamp [ACCESS/
PC] (l 33, 103, 113)
15 Mode dial (l 36)
16 Joystick (l 36)
17 Recording start/stop button (l 46)
18 Disc eject lever [DISC EJECT] (l 33)
19 When recording: Zoom lever [W/T] (l 53)
When playing back: Volume lever
[sVOLr] (l 67)
20 Photoshot button [ ] (l 48, 49)
21 Accessory shoe
≥ Accessories, such as a video DC light
(optional), are attached here.
22 Eyepiece corrector knob (l 43)
23 Tripod receptacle (l 19)
24 Battery release lever [BATTERY] (l 28)
Due to limitations in LCD production
technology, there may be some tiny bright
or dark spots on the viewfinder screen.
However, this is not a malfunction and
does not affect the recorded picture.
3
4
1
2
1
2
11
1
4
1
3
1
5
1
6
1
8
5
6
7
8
9
10
1
7
19 20
21 22
23
24
LSQT1150.book 16 ページ ２００７年１月１９日 金曜日 午前９時２７分
17
LSQT1150
Before using
25 LCD monitor (l 19)
26 Terminal cover
27 Microphone terminal [MIC] (VDR-D310)
≥ A compatible plug-in powered microphone
can be used as an external microphone.
≥ When the unit is connected with the AC
adaptor, sometimes noise may be heard
depending on the microphone type. In this
case, please switch to the battery for the
power supply and the noise will stop.
28 Audio-video output terminal [A/V]
(l 85, 87)
29 Speaker
30 Mode select switch [AUTO/MANUAL/
FOCUS] (l 45, 60, 61)
31 Reset button [RESET] (l 130)
32 Card slot cover [SD CARD] (VDR-D310/
VDR-D230) (l 35)
33 Card access lamp (VDR-D310/VDR-D230)
(l 36)
34 Card slot (VDR-D310/VDR-D230) (l 35)
35 USB terminal [ ] (VDR-D310/VDR-D230)
(l 88, 102, 112)
36 Disc compartment (l 33)
37 Grip belt (l 18)
Due to limitations in LCD production
technology, there may be some tiny bright
or dark spots on the LCD monitor screen.
However, this is not a malfunction and
does not affect the recorded picture.
25
27
29
30
31
35
34
33
32
28
26
35
28
28
VDR-D310
VDR-D230
VDR-D210
36
37
LSQT1150.book 17 ページ ２００７年１月１９日 金曜日 午前９時２７分
18
LSQT1150
Before using
Adjust the belt length so it fits your hand.
Adjust the belt length and the pad
position.
1 Flip the belt.
2 Adjust the length.
3 Replace the belt.
Attach the lens cap to protect the surface of the
lens.
1 Pass the end of the lens cap cord
through the belt.
2 Pass the lens cap through the
loop.
3 To attach or remove the lens cap,
hold both sides of the lens cap
with the tips of your finger and
thumb.
During recording
The removed lens cap can be attached to the
lens cap fixture.
Using grip belt
Attaching the lens cap
3
1
2
LSQT1150.book 18 ページ ２００７年１月１９日 金曜日 午前９時２７分
19
LSQT1150
Before using
Rotate the lens hood counterclockwise A to remove it.
∫ VDR-D310
In order to attach it, place into slot
B, and then rotate it clockwise C.
∫ VDR-D230/VDR-D210
In order to attach it, rotate it
clockwise B.
This is a hole for attaching the unit to the optional
tripod.
(Please carefully read the operating instructions
for how to attach the unit to the tripod.)
≥ When the tripod is used, the card slot cover
cannot be opened. Insert an SD card before
attaching this unit to the tripod. (l 35)
You can record the image while viewing it on the
LCD monitor.
Lens hood
A
B
C
Tripod receptacle
Using the LCD monitor
A
B
LSQT1150.book 19 ページ ２００７年１月１９日 金曜日 午前９時２７分
20
LSQT1150
Before using
1 Place your finger on the LCD
monitor open part A and pull the
LCD monitor out in the direction
of the arrow.
≥ It can open up to 90o.
2 Adjust the angle of the LCD
monitor as desired.
≥ It can rotate up to 180o A towards the lens or
90o B towards the viewfinder.
≥ The brightness and color level of the LCD
monitor can be adjusted from the menu.
(l 43)
≥ The unit may be damaged or fail if the LCD
monitor is forcibly opened or rotated.
≥ If the LCD monitor is rotated by 180x towards
the lens and the viewfinder is extended (when
recording yourself), the LCD monitor and the
viewfinder simultaneously light.
Pull out the viewfinder.
The viewfinder will be activated. (If the LCD
monitor is opened, the viewfinder will be
deactivated.)
≥ The brightness of the viewfinder (l 43) and
the field of view (l 43) can be adjusted.
1 Photoshot button [PHOTO SHOT, ]*
2 On-screen display button [EXT DISPLAY]
(l 86)
3 Date/time button [DATE/TIME] (l 42)
4 Playback operation buttons (l 66)
5 Delete button [ ]*
6 Direction buttons [3,4,2,1] (l 41)
7 Recording start/stop button [START/
STOP]*
8 Zoom/volume buttons [ZOOM, VOL]*
9 Menu button [MENU]* (l 41)
10 Enter button [ENTER] (l 41)
* means that these buttons function in the same
manner as the corresponding buttons on the
unit.
∫ Install a button-type battery
Install the supplied button-type battery in the
remote control before using it.
Using the viewfinder
A
AB
Using the remote control
(VDR-D310)
ZOOM
START/
STOP
PHOTO
SHOT
EXT
DISPLAY
DATE/
TIME
VOL
PLAY
STOPSKIP SKIP
MENU
ENTER
PAU SE
SEARCH
STILL ADV STILL ADV
SEARCH
1
2
3
4
6
7
8
9
1
0
5
LSQT1150.book 20 ページ ２００７年１月１９日 金曜日 午前９時２７分
21
LSQT1150
Before using
1 While pressing the stopper A,
pull out the battery holder.
2 Set the button-type battery with
its (r) mark facing upward and
then put the battery holder back
in place.
∫ Concerning the button-type battery
≥ When the button-type battery runs down,
replace it with a new battery (part number:
CR2025). The battery should normally last
about 1 year, however this depends on how
frequently the unit is used.
≥ Keep the button-type battery out of the reach of
children.
∫ Remote control usable range
The distance between the remote control and the
unit’s remote control sensor A: Within approx.
5m (16feet)
Angle: Approx. 10o up and 15o down, left, and
right
≥ The remote control is intended for indoor
operation. Outdoors or under strong light, the
unit may not operate properly even within the
usable ranges.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type recommended by the
manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
Replace battery with Panasonic PART NO.
CR2025 only. Use of another battery may
present a risk of fire or explosion.
Caution: Battery may explode if mistreated.
Dispose of used battery promptly. Keep away
from children.
Do not recharge, disassemble or dispose of in
fire.
A
AA
LSQT1150.book 21 ページ ２００７年１月１９日 金曜日 午前９時２７分
Before using
22
LSQT1150
Discs and cards
Discs that can be used on this unit
Disc type DVD-RAM
8 cm (3z)
Single sided/
double sided
DVD-RW
8 cm (3z)
Single sided/double sided
(DVD-RAM
Ver. 2.1)
[DVD-RW Ver. 1.1/2X-SPEED (2X/1X)]
Recording format DVD Video
Recording format
(VR format)
DVD Video
Recording format
(VR format)
DVD-Video format
(Video format)
Characteristic Rewritable disc Rewritable disc One time recording
disc
*1
Display on the screen
Indication in these
instructions
(RAM) (-RW‹VR›) (-RW‹V›)
Functions
≥ Deleting recorded scenes ¥¥ –
≥ Editing on this unit ¥¥ –
≥ Playback on other
products
*2
¥
*3
¥
*4
¥
*5
≥ Recording after finalizing – ¥¥
*6
LSQT1150.book 22 ページ ２００７年１月１９日 金曜日 午前９時２７分
Before using
23
LSQT1150
*1 By formatting the disc, it can be used repeatedly. (l 82)
*2 DVD players and DVD recorders that support 8 cm (3z) discs.
*3 Playback is possible on compatible products.
*4 Must be finalized on this unit. (l 81) Playback is possible on compatible products.
*5 Must be finalized on this unit. (l 81) Playback of DVD-R DL is possible on compatible products.
*6 Un-finalize the disc. (l 82)
Disc type DVD-R
8cm (3z)
Single sided/double sided
DVD-R DL
8cm (3z)
Dual layer on single side
(DVD-R for General Ver. 2.0) (DVD-R for DL Ver. 3.0)
Recording format DVD-Video format
(Video format)
DVD-Video format
(Video format)
Characteristic One time recording disc One time recording disc
Display on the screen
Indication in these
instructions
(-R)
Functions
≥ Deleting recorded scenes –
≥ Editing on this unit –
≥ Playback on other
products
*2
¥
*5
≥ Recording after finalizing –
¥: available –: not available
LSQT1150.book 23 ページ ２００７年１月１９日 金曜日 午前９時２７分
Before using
24
LSQT1150
≥ For the purposes of these operating instructions, DVD-R and DVD-R DL are referred to as the
“DVD-R”.
≥ Still pictures cannot be recorded on a disc with this unit. (VDR-D310/VDR-D230)
≥ You cannot record or play continuously from one side of the disc to the other when using a double
sided disc. You will need to eject the disc and turn it over.
≥ Discs inserted in a holder, cartridge, or caddy case cannot be used. Always remove bare discs from
these containers prior to use.
≥ It is recommended that you use Panasonic discs. Usually discs compatible with the DVD standard
can be used for recording and playback with no problems. However, some commercially available
discs do not meet the DVD standard for quality and performance. If you use one of these discs, you
may not be able to record or playback normally. (The message “RECOMMENDED TO USE
PANASONIC DISC” appears.) Refer to the following support site for information about discs that have
been confirmed as compatible by Panasonic.
http://panasonic.co.jp/pavc/global/cs/e_cam (This website is in English only.)
≥ Discs recorded on this unit may not be playable on other products.
≥ Recording on DVD-R in DVD Video Recording format is not supported.
≥ When using DVD-RW or DVD-R, do not perform the following as it may make the disc
unusable.
jRecord on a disc with other products after recording on it with this unit.
jRecord on a disc with this unit after recording on it with other products.
jInsert an un-finalized disc in any other products.
∫ About format types
≥ If a disc is recorded in VR format, the data can be exported on a computer.
∫ About DVD-R DL (Dual Layer)
DVD-R DL (Dual Layer) discs have two layers of recording/playback surface on one side.
If the first layer (L0) becomes full during recording, the recording continues uninterrupted on the second
layer (L1). However, the recorded picture is divided into 2 scenes at the point where the layers switch.
The unit automatically switches layers during disc playback so you can play the whole of the disc
continuously like a normal disc. However, the image or sound momentarily stop at the point where the
layers switch.
∫ Examples of discs that cannot be used on this unit
What is the DVD Video Recording format (VR
format)?
This is a format for recording on DVD discs
which allows you to record and erase repeatedly
and create playlists. You can record on DVDRAM and DVD-RW in VR format with this unit.
What is the DVD-Video format (Video
format)?
By finalizing the disc, it can be played back on
most DVD players.
You can record on DVD-RW and DVD-R in
Video format with this unit.
≥ Discs other than those with diameter of 8 cm (3z) ≥ CD-RW
≥ Double layer discs other than DVD-R DL ≥ CD-R
≥iRW ≥ CD-ROM
≥iR ≥ CD
≥ DVD-ROM
≥ DVD-Video
LSQT1150.book 24 ページ ２００７年１月１９日 金曜日 午前９時２７分
Before using
25
LSQT1150
When using DVD-RW, select whether to record in DVD Video Recording format (VR format) or DVDVideo format (Video format) and then format the disc. (l 24, About format types)
1 When a brand-new DVD-RW is inserted in this unit,
the screen on the right appears. Select [YES], then
press the joystick.
2 Select format type, then press the joystick.
3 When the confirmation message appears, select [YES], then press the
joystick.
≥ To change the format type, format the disc again. (l 82)
If the disc is formatted, then all the data recorded on the disc will be erased.
When using brand-new DVD-RW
[VIDEO]: DVD-Video format
[VR]: DVD Video Recording format
LSQT1150.book 25 ページ ２００７年１月１９日 金曜日 午前９時２７分
Before using
26
LSQT1150
≥ For the purposes of these operating instructions, SD Memory Card and SDHC Memory Card are
referred to as the “SD card”.
≥ Motion pictures cannot be recorded on an SD card with this unit.
≥ Please confirm the latest information on the following website. (This website is in English only.)
http://panasonic.co.jp/pavc/global/cs/e_cam
≥ This unit supports SD Memory Cards formatted in FAT12 system and FAT16 system based on SD
Memory Card Specifications and SDHC Memory Cards formatted in FAT32 system.
≥ Use this unit to format SD cards. If an SD card is formatted on other products (such as a computer),
the time spent for recording may become longer and you may not be able to use the SD card. (l 83)
≥ We recommend that you use a Panasonic brand SD card.
≥ When the write-protect switch A on SD card is locked, no recording, deletion or
editing will be possible on the card.
≥ Keep the Memory Card out of reach of children to prevent swallowing.
≥ A MultiMediaCard cannot be used on this unit.
Cards that you can use with this unit (VDR-D310/VDR-D230)
Card type SD Memory Card SDHC Memory Card
Capacity
8 MB, 16 MB, 32 MB, 64 MB, 128 MB, 256 MB,
512 MB, 1 GB, 2 GB
4GB
Indication in these
instructions
(SD)
This unit is compatible with both SD Memory cards and SDHC Memory cards. You can only use
SDHC Memory cards on devices that are compatible with them. You cannot use SDHC Memory
cards on devices that are only compatible with SD Memory cards. (When using an SDHC Memory
card on another device, be sure to read the operating instructions for that device.)
A
LSQT1150.book 26 ページ ２００７年１月１９日 金曜日 午前９時２７分
Before using
27
LSQT1150
∫ How to hold a disc or card
Do not touch the recording/playback surface or the
terminal surface.
∫ When inserting/removing a disc
Do not allow the recording/playback side of the disc to get dirty and avoid fingerprints.
≥ If there is a scratch or dirt (e.g. dust or fingerprints) on the recording/playback side of the disc, images
cannot be recorded or played back normally and the following phenomena may occur:
jRecording or playback becomes impossible.
jPlayback image stops momentarily or sound is interrupted during playback.
jBlock noise appears on playback images.
jThe message “PLEASE CHECK FOR SCRATCHES OR STAINS ON DISC.” appears.
∫ If there is dirt on the disc
Clean it with the supplied disc cleaning cloth. Wipe the disc
from the center to the outer edge to remove the dirt. Do not
use force when wiping the disc as it may scratch it. Also, do
not use solvents (thinner, water, antistatic agent, detergent
etc.)
∫ Handling precautions
≥ Be careful about scratches and dirt.
≥ Do not attach labels or stickers to discs.
(This may cause disc warping and un-balanced rotation, rendering it unusable.)
≥ Write on the label side of the disc only with a soft, oil-based felt pen. Do not use ballpoint pens or
other hard writing implements.
≥ Do not use record cleaning sprays, benzine, thinner, static electricity prevention liquids or any other
solvent.
≥ Do not use scratch-proof protectors or covers.
≥ Do not drop, stack, or impact discs. Do not place objects on them.
≥ Do not use the following discs:
jDiscs with exposed adhesive from removed stickers or labels.
jDiscs that are badly warped or cracked.
jIrregularly shaped discs, such as heart shapes.
≥ Do not expose the terminals of the card to water, garbage or dust.
≥ Do not place in the following areas:
jIn direct sunlight.
jIn very dusty or humid areas.
jNear a heater.
jLocations susceptible to significant difference in temperature (condensation can occur).
jWhere static electricity or electromagnetic waves occur.
≥ Put discs and cards back in their cases for protection when not using them.
Disc and card handling
LSQT1150.book 27 ページ ２００７年１月１９日 金曜日 午前９時２７分
28
LSQT1150
Setup
Setup
Power supply
When this unit is purchased, the battery is not
charged. Charge the battery before using this
unit.
≥ If the DC cable is connected to the AC
adaptor, then the battery will not charge.
Remove the DC cable from the AC adaptor.
1 Connect the AC cable to the AC
adaptor and the AC outlet.
2 Put the battery on the battery
mount by aligning the mark, and
then securely plug it in.
≥ The output plug of the AC cable is not
completely connected to the AC adaptor jack.
As shown in A, there is a gap.
∫ Charging lamp
≥ Battery charging time (l 29)
≥ We recommend using Panasonic batteries.
(l 15, 143)
≥ If you use other batteries, we cannot guarantee
the quality of this product.
Push the battery against the battery
holder and slide it until it clicks.
While sliding the BATTERY lever,
slide the battery to remove it.
≥ Hold the battery with your hand so it does not
fall.
≥ Before removing the battery, be sure to set the
OFF/ON switch to OFF and check that the
status indicator is off.
Charging the battery
Lights up: Charging
Goes off: Charging completed
Flashing: The battery is over discharged
(discharged excessively). In a while,
the lamp will light up and normal
charging will start.
When the battery temperature is
excessively high or low, the
CHARGE lamp flashes and the
charging time will be longer than
normal.
A
Inserting the battery
Removing the battery
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type recommended by the
manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
LSQT1150.book 28 ページ ２００７年１月１９日 金曜日 午前９時２７分
Setup
29
LSQT1150
The times shown in the tables below are for when the temperature is 25 oC (77 oF) and the humidity is
60%. If the temperature is higher or lower than 25 oC (77 oF), the charging time will become longer.
∫ Charging time
≥ The charging time shown in the table are approximations.
≥ “2 h 25 min” indicates 2 hours 25 minutes.
VDR-D310:
VDR-D230/VDR-D210:
Charging time and recordable time
Battery model number Voltage/capacity Charging time
Supplied battery/
CGA-DU12 (optional)
7.2 V/1150 mAh 2 h 25 min
CGA-DU21 (optional) 7.2 V/2040 mAh 3 h 55 min
Battery model number Voltage/capacity Charging time
Supplied battery/
CGR-DU06 (optional)
7.2 V/640 mAh 1 h 40 min
CGA-DU12 (optional) 7.2 V/1150 mAh 2 h 25 min
CGA-DU21 (optional) 7.2 V/2040 mAh 3 h 55 min
LSQT1150.book 29 ページ ２００７年１月１９日 金曜日 午前９時２７分
Setup
30
LSQT1150
∫ Recordable time (When using a DVD-RAM disc)
≥ The times indicate the recordable time when the viewfinder is used. The times in parentheses
indicate the recordable time when the LCD monitor is used.
≥ The actual recordable time refers to the recordable time on a disc when repeatedly starting/stopping
recording, turning the unit on/off, moving the zoom lever, etc.
≥ “1 h 25 min” indicates 1 hour 25 minutes.
VDR-D310:
Battery model
number
Voltage/
capacity
Recording
mode
Maximum
continuously
recordable time
Actual recordable
time
Supplied battery/
CGA-DU12 (optional)
7.2 V/
1150 mAh
XP
1h25min
(1 h 20 min)
35 min
(35 min)
SP
1h40min
(1 h 30 min)
45 min
(40 min)
LP
1h45min
(1 h 40 min)
45 min
(45 min)
CGA-DU21 (optional)
7.2 V/
2040 mAh
XP
2h50min
(2 h 40 min)
1h15min
(1h10min)
SP
3h10min
(3 h)
1h25min
(1h20min)
LP
3h20min
(3 h 5 min)
1h30min
(1h20min)
LSQT1150.book 30 ページ ２００７年１月１９日 金曜日 午前９時２７分
Loading...