PANASONIC TH60PF30ER User Manual

Operating Instructions

High Deﬁ nition Plasma Display

Model No.

TH-60PF30ER TH-65PF30ER

English

Please read these instructions before operating your set and retain them for future reference.

Dear Panasonic Customer

Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new Plasma Display. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt also, and note down the model number and serial number of your set in the space provided on the rear cover of these instructions. Visit our Panasonic Web Site http://panasonic.net

Table of Contents

Important Safety Notice ........................................... 3

Safety Precautions ................................................... 4

3D Safety Precautions ............................................. 7

Accessories .............................................................. 9

Accessories Supply ................................................. 9

Remote Control Batteries ........................................ 9

Connections ............................................................ 10

Speaker connection ............................................... 10

AC cord connection and ﬁ xing, cable ﬁ xing ........... 10

Video equipment connection ..................................11

VIDEO and COMPONENT / RGB IN connection ...11

HDMI connection ................................................... 12

DVI-D IN connection .............................................. 12

PC Input Terminals connection .............................. 13

SERIAL Terminals connection ............................... 14

Power On / Off ......................................................... 15

Selecting the input signal ...................................... 17

Basic Controls ........................................................ 18

ASPECT Controls ................................................... 20

Digital Zoom ............................................................ 21

Viewing 3D images ................................................. 22

To view the 3D images .......................................... 22

Troubleshooting for 3D Eyewear .......................... 23

Table of images that can be seen for each 3D

Picture Format and the source image format ........ 23

On-Screen Menu Displays ..................................... 24

Adjusting Pos./Size ................................................ 25

Picture Adjustments ............................................... 28

Advanced settings ................................................. 29

Picture Proﬁ les ....................................................... 30

Saving proﬁ les ....................................................... 31

Loading proﬁ les ..................................................... 32

Editing proﬁ les ....................................................... 32

Sound Adjustment .................................................. 33

SDI Sound Output ................................................. 33

PRESENT TIME Setup / Set up TIMER .................. 34

PRESENT TIME Setup .......................................... 34

Set up TIMER ........................................................ 34

3D Settings .............................................................. 35

Screensaver (For preventing image retention) .... 36

Setup of Screensaver Time ................................... 37

Reduces screen image retention .......................... 38

Extended life settings ............................................ 38

Reduces power consumption ............................... 41

Customizing the Input labels ................................. 42

Selecting the On-Screen Menu Language ............ 43

Display orientation ................................................. 43

Setup for MULTI DISPLAY ...................................... 44

How to Setup MULTI DISPLAY ............................. 44

ID Remote Control Function .................................. 45

Set up for Portrait ................................................... 46

How to setup Portrait ............................................. 46

Setup for Input Signals .......................................... 48

Component / RGB-in select ................................... 48

YUV / RGB-in select .............................................. 48

Signal menu .......................................................... 49

Network Setup ........................................................ 52

Options Adjustments ............................................. 53

3D Safety Precautions (To hide 3D Safety

Precautions) ......................................................... 56

Weekly Command Timer ....................................... 56

Audio input select .................................................. 58

Touch Panel settings (Settings when using

Touch Panel) ......................................................... 59

Using Network Function ........................................ 60

Example of Network Connection ........................... 60

Command Control ................................................. 60

PJLink™ Protocol .................................................. 61

Using Web Browser Control .................................. 62

Before Using Web Browser Control....................... 62

Access from Web Browser .................................... 62

Display Control (BASIC CONTROL/OPTION

CONTROL Screen) ............................................... 63

NETWORK SETTING (Network Setup Screen) .... 64

Password Setting (Password Setup Screen) ........ 64

Troubleshooting ..................................................... 65

List of Aspect Modes ............................................. 66

Applicable Input Signals ........................................ 67

Shipping condition ................................................. 68

Command list of Weekly Command Timer ........... 69

Speciﬁ cations ......................................................... 70

Important Safety Notice

IMPORTANT: THE MOULDED PLUG

WARNING

1) To prevent damage which may result in ﬁ re or shock hazard, do not expose this appliance to dripping or splashing.

Do not place containers with water (ﬂ ower vase, cups, cosmetics, etc.) above the set. (including on

shelves above, etc.)

No naked ﬂ ame sources, such as lighted candles, should be placed on / above the set.

2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualiﬁ ed service personnel.

3) Do not remove the earthing pin on the power plug. This apparatus is equipped with a three pin earthing-type power plug. This plug will only ﬁ t an earthing-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician.

Do not defeat the purpose of the earthing plug.

4) To prevent electric shock, ensure the earthing pin on the AC cord power plug is securely connected.

CAUTION

This appliance is intended for use in environments which are relatively free of electromagnetic ﬁ elds. Using this appliance near sources of strong electromagnetic ﬁ elds or where electrical noise may overlap with the input signals could cause the picture and sound to wobble or cause interference such as noise to appear. To avoid the possibility of harm to this appliance, keep it away from sources of strong electromagnetic ﬁ elds.

FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This display is supplied with a moulded three pin mains plug for your safety and convenience. A 10 amp fuse is ﬁ tted in this plug. Shall the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark

If the plug contains a removable fuse cover, you must ensure that it is reﬁ tted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic dealer.

Do not cut off the mains plug. Do not use any other type of mains lead except the one supplied with this display. The supplied mains lead and moulded plug are designed to be used with this display to avoid interference and for your safety. If the socket outlet in your home is not suitable, get it changed by a qualiﬁ ed electrician. If the plug or mains lead becomes damaged, purchase a replacement from an authorized dealer.

WARNING : — THIS DISPLAY MUST BE EARTHED.

How to replace the fuse.

Trademark Credits

• VGA is a trademark of International Business Machines Corporation.

• Macintosh is a registered trademark of Apple Inc., USA.

• SVGA, XGA, SXGA and UXGA are registered trademarks of the Video Electronics Standard Association.

• HDMI, the HDMI Logo, and High-Deﬁ nition Multimedia Interface are trademarks or registered trademarks of HDMI

IMPORTANT: THE MOULDED PLUG

or the BSI mark on the body of the fuse.

ASA

Open the fuse compartment with a screwdriver and replace the fuse.

Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected.

Licensing LLC in the United States and other countries.

Note:

Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention to remain on the Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.

Safety Precautions

WARNING

Setup

This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury.

(All of the following accessories are manufactured by Panasonic Corporation.)

• Speakers ........................................................................ TY-SP58P10WK (for TH-60PF30ER),

TY-SP65P11WK (for TH-65PF30ER)

• Pedestal ......................................................................... TY-ST58P20 (for TH-60PF30ER),

TY-ST65P20 (for TH-65PF30ER)

• Mobile stand ................................................................... TY-ST58PF20 (for TH-60PF30ER)

• Wall-hanging bracket (angled) ....................................... TY-WK65PR20

• BNC Dual Video Terminal Board .................................... TY-FB9BD

• HD-SDI Terminal Board with audio ................................ TY-FB10HD

• Dual Link HD-SDI Terminal Board .................................. TY-FB11DHD

• Dual HD-SDI Terminal Board for 3D .............................. TY-FB30DHD3D

• Dual HDMI Terminal Board ............................................ TY-FB10HMD

• Ir Through Terminal Board.............................................. TY-FB9RT

• DVI-D Terminal Board .................................................... TY-FB11DD

• Dual DVI-D Terminal Board for 3D ................................. TY-FB30DD3D

• AV Terminal Box ............................................................. TY-TB10AV

• 3D IR TRANSMITTER ................................................... TY-3D30TRW

• Touch Panel ................................................................... TY-TP65P10S (for TH-65PF30ER)

Always be sure to ask a qualiﬁ ed technician to carry out set-up.

Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from being played with by young children, creating the potential risk of suffocation.

Do not place the Plasma Display on sloped or unstable surfaces, and ensure that the Plasma Display does not hang over the edge of the base.

• The Plasma Display may fall off or tip over.

Do not place any objects on top of the Plasma Display.

• If water is spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result

in ﬁ re or electric shock. If any foreign objects get inside the Plasma Display, please consult your local Panasonic dealer.

Transport only in upright position!

• Transporting the unit with its display panel facing upright or downward may cause damage to the internal

circuitry.

Ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table cloths and curtains.

For sufﬁ cient ventilation; If using the pedestal (optional accessory), leave a space of 10 cm or more at the top, left and right, and 7 cm or more at the rear, and also keep the space between the bottom of the display and the ﬂ oor surface. If using some other setting-up method, follow the manual of it. (If there is no speciﬁ c indication of installation dimension in the installation manual, leave a space of 10 cm or more at the top, bottom, left and right, and 7 cm or more at the rear.)

When installing the Plasma Display vertically;

Turn up the power switch for the upward direction when you install the Plasma Display vertically. And set “Display orientation” to “Portrait” in Setup menu. (see page 43)

Safety Precautions

When using the Plasma Display

The Plasma Display is designed to operate on 220 - 240 V AC, 50/60 Hz.

Do not cover the ventilation holes.

• Doing so may cause the Plasma Display to overheat, which can cause ﬁ re or damage to the Plasma Display.

Do not stick any foreign objects into the Plasma Display.

• Do not insert any metal or ﬂ ammable objects into the ventilations holes or drop them onto the Plasma Display, as doing so can cause ﬁ re or electric shock.

Do not remove the cover or modify it in any way.

• High voltages which can cause severe electric shocks are present inside the Plasma Display. For any inspection, adjustment and repair work, please contact your local Panasonic dealer.

Ensure that the mains plug is easily accessible.

An apparatus with CLASS I construction shall be connected to a mains socket outlet with a protective earthing connection.

Do not use any power supply cord other than that provided with this unit.

• Doing so may cause ﬁ re or electric shocks.

Securely insert the power supply plug as far as it will go.

• If the plug is not fully inserted, heat may be generated which could cause ﬁ re. If the plug is damaged or the wall socket is loose, they shall not be used.

Do not handle the power supply plug with wet hands.

• Doing so may cause electric shocks.

Do not do anything that may damage the power cable. When disconnecting the power cable, pull on the plug body, not the cable.

• Do not damage the cable, make any modiﬁ cations to it, place heavy objects on top of it, heat it, place it near any hot objects, twist it, bend it excessively or pull it. To do so may cause ﬁ re and electric shock. If the power cable is damaged, have it repaired at your local Panasonic dealer.

If the Plasma Display is not going to be used for any prolonged length of time, unplug the power supply plug from the wall outlet.

To prevent the spread of ﬁ re, keep candles or other open ﬂ ames away from this product at all times.

If problems occur during use

If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odour starts to come out from the Plasma Display, immediately unplug the power supply plug from the wall outlet.

• If you continue to use the Plasma Display in this condition, ﬁ re or electric shock could result. After checking that the smoke has stopped, contact your local Panasonic dealer so that the necessary repairs can be made. Repairing the Plasma Display yourself is extremely dangerous, and shall never be done.

If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet becomes damages, disconnect the power supply plug immediately.

•

A short circuit may occur, which could cause ﬁ re. Contact your local Panasonic dealer for any repairs that need to be made.

Safety Precautions

CAUTION

When using the Plasma Display

Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display.

• Heated air comes out from the ventilation holes at the top of Plasma Display will be hot. Do not bring your hands or face, or objects which cannot withstand heat, close to this port, otherwise burns or deformation could result.

Be sure to disconnect all cables before moving the Plasma Display.

• If the Plasma Display is moved while some of the cables are still connected, the cables may become damaged, and ﬁ re or electric shock could result.

Disconnect the power supply plug from the wall socket as a safety precaution before carrying out any cleaning.

• Electric shocks can result if this is not done.

Clean the power cable regularly to prevent it becoming dusty.

• If dust built up on the power cord plug, the resultant humidity can damage the insulation, which could result in ﬁ re. Pull the power cord plug out from the wall outlet and wipe the mains lead with a dry cloth.

Do not burn or breakup batteries.

• Batteries must not be exposed to excessive heat such as sunshine, ﬁ re or the like.

This Plasma Display radiates infrared rays, therefore it may affect other infrared communication equipment. Install your infrared sensor in a place away from direct or reﬂ ected light from your Plasma Display.

Cleaning and maintenance

The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth.

• If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface is dry.

• Do not scratch or hit the surface of the panel with ﬁ ngernails or other hard objects, otherwise the surface may become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected.

If the cabinet becomes dirty, wipe it with a soft, dry cloth.

• If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.

• Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get inside the unit, operating problems may result.

• Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC.

3D Safety Precautions

Safety Precautions

WARNING

Small Parts

3D Eyewear contains small parts (battery and specialised band, etc.) and must be kept out of reach of small children to avoid accidental ingestion.

Disassembly

Do not disassemble or modify the 3D Eyewear.

Lithium Battery

Batteries must not be exposed to excessive heat such as sunshine, ﬁ re or the like.

CAUTION

To enjoy 3D images safely and comfortably, please read these instructions fully.

Use for commercial applications and public viewing

Someone in authority should responsibly convey the precautions for use of the 3D Eyewear to the user.

3D Eyewear

Do not drop, exert pressure on, or step on the 3D Eyewear.

Always store the 3D Eyewear in the case provided when not in use.

Be careful of the tips of the frame when putting on the 3D Eyewear.

Be careful not to trap a ﬁ nger in the hinge section of the 3D Eyewear.

Pay special attention when children are using the 3D Eyewear. 3D Eyewear should not be used by children younger than 5 - 6 years old, as a guideline. All children must be fully supervised by parents or guardians who must ensure their safety and health throughout the using 3D Eyewear.

Safety Precautions

Viewing 3D Content

Content for 3D viewing includes commercially available Blu-ray discs, 3D broadcasts, etc. When preparing your own 3D content, ensure that it is properly produced.

Do not use the 3D Eyewear if you have a history of over-sensitivity to light, heart problems, or have any other existing medical conditions.

Please stop using the 3D Eyewear immediately, if you feel tired, are not feeling well or experience any other uncomfortable sensation.

Take an appropriate break after viewing a 3D movie. Take a break of between 30 - 60 minutes after viewing 3D content on interactive devices such as 3D games

or computers. Be careful not to strike the screen or other people unintentionally. When using the 3D Eyewear the distance

between the user and screen can be misjudged. The 3D Eyewear must only be worn when viewing 3D content. If you do not look toward the screen for a while when viewing 3D images, the 3D Eyewear may be turned off

automatically. If you suffer from any eyesight problems (short / far-sighted, astigmatism, eyesight differences in left and

right), please ensure to correct your vision before using the 3D Eyewear. Stop using the 3D Eyewear if you can clearly see double images when viewing 3D content. Do not use the 3D Eyewear at a distance less than the recommended distance.

View from at least the recommended distance (3 times the effective height of the screen). Recommended distance TH-60PF30ER: 2.2 m TH-65PF30ER: 2.4 m When the top and bottom area of the screen is blackened, such as movies, view the screen at a distance 3 times further than the height of the actual image. (That makes the distance closer than above recommended ﬁ gure.)

3D Eyewear Use

Before using the 3D Eyewear, ensure no breakable objects surrounding the user to avoid any accidental damage or injury.

Remove the 3D Eyewear before moving around to avoid falling or accidental injury. Always put the 3D Eyewear in the case (supplied) after use. Use the 3D Eyewear only for the intended purpose and nothing else. Do not use 3D Eyewear in the condition of high temperature. Do not use if the 3D Eyewear is physically damaged. Do not use any devices that emit the infrared signals near the 3D Eyewear, as this may cause the 3D Eyewear

false operations. Do not use devices (such as mobile phones or personal transceivers) that emit strong electromagnetic waves

near the 3D Eyewear as this may cause the 3D Eyewear to malfunction. Stop using the 3D Eyewear immediately if a malfunction or fault occurs. Stop using the 3D Eyewear immediately if you experience any redness, pain, or skin irritation around the nose

or temples. In rare cases, the materials used in the 3D Eyewear may cause an allergic reaction.

Lithium Battery

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

Accessories

Accessories Supply

Check that you have the accessories and items shown

Operating Instruction book

Power supply cord Clamper × 1

CD-ROM (Operating instructions)

TMME289

Remote Control Batteries

Remote Control Transmitter N2QAYB000535

Batteries for the Remote Control Transmitter (R6 (UM3) Size × 2)

Ferrite core × 2 J0KG00000014

Use the Ferrite cores to comply with the EMC standard. (see page 60)

Requires two R6 batteries.

1. Pull and hold the hook, then open the battery cover.

2. Insert batteries - note correct polarity ( + and -).

“R6 (UM3)” size

3. Replace the cover.

Helpful Hint:

For frequent remote control users, replace old batteries with Alkaline batteries for longer life.

Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Disposal of batteries should be in an environment-friendly manner.

Observe the following precaution:

1. Batteries shall always be replaced as a pair. Always use new batteries when replacing the old set.

2. Do not combine a used battery with a new one.

3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).

4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

Battery replacement is necessary when remote control acts sporadically or stops operating the Plasma Display set.

6. Do not burn or breakup batteries. Batteries must not be exposed to excessive heat such as sunshine, ﬁ re or the like.

Connections

Speaker connection

When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation.

Speakers (Optional accessories)

Red

Black

While pressing the lever, insert the core wire.

Red

Black

Return the lever.

AC cord connection and ﬁ xing, cable ﬁ xing

AC cord ﬁ xing

Unplug the AC cord

Plug the AC cord into the display unit.

Plug the AC cord until it clicks.

Note:

Make sure that the AC cord is locked on

Using the clamper

Secure any excess cables with clamper as required.

Note:

One clamper is supplied with this unit. In case of securing cables at three positions, please purchase it separately.

TH-60PF30ER TH-65PF30ER

both the left and right sides.

Unplug the AC cord pressing the two knobs.

Note:

When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet ﬁ rst.

Attach the clamper

Insert the clamper in a hole.

hole

To remove from the unit:

snaps

Keep pushing both side snaps

Bundle the cables

hooks

Set the tip in the hooks

To loosen:

knob

Keep pushing the knob

Video equipment connection

Ex. TH-65PF30ER

3D IR TRANSMITTER:

Connect the 3D IR TRANSMITTER (optional accessory).

SLOT: Terminal board (optional

accessories) insert slot (see

page 4)

Note:

The right side slot is for terminal board with 2-slot width. The terminal board with 1-slot width does not function when installed in the right side slot.

Connections

SERIAL:

Control the Plasma Display by connecting to PC (see page 14)

LAN: Connect to a network to control the unit. (see

page 60)

AV IN (VIDEO): Composite Video Input Terminal (see below) COMPONENT/RGB IN: Component/RGB Video Input Terminal

(see below) AV IN (HDMI): HDMI Input Terminal (see page 12) Connect to video equipment such as VCR or DVD player.

DVI-D IN: DVI-D Input Terminal

PC IN:

PC Input Terminal Connect to video terminal of PC or equipment with Y, PB(CB) and PR(CR) output (see page 13).

Terminals are on the bottom side of the Plasma Display.

(see page 12)

VIDEO and COMPONENT / RGB IN connection

Note:

Additional equipment, cables and adapter plugs shown are not supplied with this set.

RCA-BNC Adapter plug

Notes:

• Change the “Component/RGB-in select” setting in the “Setup” menu to “Component” (when Component signal connection) or “RGB” (when RGB signal connection). (see page 48)

• Signals input to COMPONENT/RGB IN terminals correspond to Sync on G or Sync on Y.

AUDIO

OUT

VIDEO

OUT

VCR

P B

AUDIO

OUT

DVD Player

, Y , P B , P R

Computer

RGB Camcorder

Connections

HDMI connection

[Pin assignments and signal names]

Pin No.

Signal name

T.M.D.S Data2+

T.M.D.S Data2

Shield

T.M.D.S Data2-

T.M.D.S Data1+ T.M.D.S Data1

Shield

T.M.D.S Data1-

T.M.D.S Data0+ T.M.D.S Data0

Shield

T.M.D.S Data0-

T.M.D.S Clock+

Pin No.

15 16

18 19

Note:

Additional equipment and HDMI cable shown are not supplied with this set.

Signal name

T.M.D.S Clock

Shield

T.M.D.S Clock-

CEC

Reserved (N.C. on device)

SCL SDA DDC/CEC

Ground +5V Power Hot Plug Detect

HDMI

AV OUT

DVD player

HDMI cable

DVI-D IN connection

PC with DVI-D video out

DVI-video cable (Within 5 m)

Stereo mini plug (M3)

DVI-D Input Connector Pin Layouts

Connection port view

Pin No.

Signal Name

T.M.D.S. data 2-

T.M.D.S. data 2+

T.M.D.S. data 2 shield

3 4 5

DDC clock

DDC data

7 8

T.M.D.S. data 1-

T.M.D.S. data 1+

T.M.D.S. data 1 shield

11 12 24

Pin No.

Notes:

• Additional equipment and cables shown are not supplied with this set.

• Use the DVI-D cable complying with the DVI standard. Image deterioration may occur depending on the length or the quality of the cable.

Shared with PC IN.

Signal Name

+5 V DC

Ground

Hot plug detect

T.M.D.S. data 0-

T.M.D.S. data 0+

T.M.D.S. data 0 shield

19 20 21

T.M.D.S. clock shield

T.M.D.S. clock+

T.M.D.S. clock-

PC Input Terminals connection

COMPUTER

Connections

(Female) Shared with DVI-D IN.

Audio

Connect a cable which matches the audio output terminal on the computer.

Conversion adapter (if necessary)

Stereo mini plug (M3)

Mini D-sub 15p

RGB

PC cable

(Male)

Notes:

• With regard to the typical PC input signals that are described in the applicable input signals list (see page 67), adjustment values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight PC input signal types that are not included in the list.

• Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

• The display resolution is a maximum of 1,440 × 1,080 dots when the aspect mode is set to “4:3”, and 1,920 × 1,080 dots when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show ﬁ ne detail with sufﬁ cient clarity.

• The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection.

• Some PC models cannot be connected to the set.

• There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.

• The computer shown in the illustration is for example purposes only.

• Additional equipment and cables shown are not supplied with this set.

• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the speciﬁ ed frequency range.

• Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.

• To use sync input VBS signals, use the connector which incorporates a 75-ohm termination resistance and which is available on the market, for the connection of the HD connector where the VBS signals are to be input.

• Change the “Component/RGB-in select” setting in the “Setup” menu to “Component”

(when Component signal connection) or “RGB” (when RGB signal connection). (see page 48)

Signal Names for Mini D-sub 15P Connector

Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name

4 5

15 14 13 12 11

6 7 8

R (PR/CR)

G (Y)

B (PB/CB)

NC (not connected)

GND (Ground)

Pin Layout for PC Input Terminal

GND (Ground)

+5 V DC

GND (Ground)

NC (not connected)

HD/SYNC

SDA

SCL

Connections

SERIAL Terminals connection

The SERIAL terminal is used when the Plasma Display is controlled by a computer. Note: To use serial control for this unit, make sure to set the “Control I/F Select” in the “Network Setup” menu to

“RS-232C”. (see page 52)

COMPUTER

(Male)

6789

13452

RS-232C Straight cable

(Female)

D-sub 9p

Notes:

• Use the RS-232C straight cable to connect the computer to the Plasma Display.

• The computer shown is for example purposes only.

• Additional equipment and cables shown are not supplied with this set.

The SERIAL terminal conforms to the RS-232C interface speciﬁ cation, so that the Plasma Display can be controlled by a computer which is connected to this terminal. The computer will require software which allows the sending and receiving of control data which satisfies the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details.

Communication parameters

Signal level RS-232C compliant

Synchronization method Asynchronous

Baud rate 9600 bps

Parity None

Character length 8 bits

Stop bit 1 bit

Flow control -

Basic format for control data

The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent.

STX C1 C2 C3 P1 P2 P3 P4: P5 ETX

Start (02h)

Colon Parameter(s) 3-character command (3 bytes)

(1 - 5 bytes)

End (03h)

Notes:

• If multiple commands are transmitted, be sure to wait for the response for the ﬁ rst command to come from this unit before sending the next command.

• If an incorrect command is sent by mistake, this unit will send an “ER401” command back to the computer.

• S1A and S1B of Command IMS are available only when a dual input terminal board is attached.

Signal names for D-sub 9P connector

Pin No. Details

2 3 5

• 7 8

•

These signal names are those of computer speciﬁ cations.

Command

Command Parameter Control details PON None Power ON POF None Power OFF AVL ** Volume 00 - 63

AMT

IMS None

DAM None

0 Audio MUTE OFF 1 Audio MUTE ON

SL1 S1A S1B VD1 YP1

HM1 DV1 PC1

ZOOM FULL JUST NORM ZOM2 ZOM3 SJST SNOM SFUL 14:9

With the power off, this display responds to PON command only.

Pin layout for SERIAL Terminal

R X D T X D

GND

Non use

(Shorted in this set)

Input select (toggle) SLOT input (SLOT INPUT) SLOT input (SLOT INPUT A) SLOT input (SLOT INPUT B) VIDEO input (VIDEO) COMPONENT/RGB IN input (COMPONENT) HDMI input (HDMI) DVI-D IN input (DVI) PC IN input (PC)

Screen mode select (toggle) Zoom1 16:9 Just (For Video/SD signal) 4:3 (For Video/SD/PC signal) Zoom2 (For HD signal) Zoom3 (For HD signal) Just (For HD signal) 4:3 (For HD signal) 4:3 Full (For HD signal) 14:9

(For Video/SD/PC signal)

Power On / Off

Connecting the AC cord plug to the Plasma Display.

Connecting the plug to the Wall Outlet

Notes:

• Main plug types vary between countries. The power plug shown at right may, therefore, not be the type ﬁ tted to your set.

• When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet ﬁ rst.

INPUT MENU ENTER/+/VOL-/

Power Indicator

Press the Power switch on the Plasma Display to turn the set on: Power-On.

Power Indicator: Green

Press the

Power Indicator: Red (standby)

Press the button on the remote control to turn the Plasma Display on.

Power Indicator: Green

Turn the power to the Plasma Display off by pressing the switch on the unit, when the Plasma Display is on or in standby mode.

Note:

During operation of the power management function, the power indicator turns orange in the power off state.

button on the remote control to turn the Plasma Display off.

Remote Control Sensor

Power On / Off

When ﬁ rst switching on the unit

Following screen will be displayed when the unit is turned on for the ﬁ rst time. Select the items with the remote control. Unit buttons are invalid.

OSD Language

Select the language.

Set.

PRESENT TIME Setup

Select “DAY” or “PRESENT TIME”.

Setup “DAY” or “PRESENT TIME”.

Select “Set”.

Set.

OSD Language

English (UK)

Deutsch

Français

Italiano

Español

ENGLISH (US)

PRESENT TIME Setup

PRESENT TIME MON 99:99

Set DAY PRESENT TIME

PRESENT TIME Setup

PRESENT TIME MON 99:99

Set DAY PRESENT TIME

SetSelect

MON 99:99

TUE

10:00

No activity power off

To enable No activity power off, select “Enable”.

Set.

No activity power off

Display will be turned off when there is no activity for 4 hours.

If selecting “Enable”, a conﬁ rmation window appears.

Select “Yes” or “No”.

Set.

No activity power off

Are you sure you want to enable ’No activity power off’ ?

Display orientation

For vertical installation, select “Portrait”.

Set.

Display orientation

Landscape

Portrait

Notes:

• Once the items are set, the screens won't be displayed when switching on the unit next time.

• After the setting, the items can be changed in the following menus. OSD Language (see page 43) PRESENT TIME Setup (see page 34) No activity power off (see page 41) Display orientation (see page 43)

DisableEnable

NoYes

INPUT MENU ENTER/ + / VOL - /

Power On / Off

Power ON warning message

The following message may be displayed when turning the unit power ON:

3D Safety Precautions

When 3D images will be viewed by unspeciﬁ ed number of people or used for commercial applications, someone in authority should convey the following precautions. These precautions should be followed in the home as well.

3D Viewing/ 3D Content/ Viewing distance/ 3D Eyewear recommendations

- To enjoy 3D images safely and comfortably, please read the Operating Instructions fully.

Activate 3D Safety Precautions if you deliver 3D images to unspeciﬁ ed audiences for business or other purposes. If “3D Picture Display” in “3D Settings” is set to “3D”, a warning message is displayed every time the power is turned ON. (see page 35)

No activity power off Precautions

’No activity power off’ is enabled.

If “No activity power off” in Setup menu is set to “Enable”, a warning message is displayed every time the power is turned ON. (see page 41) These message displays can be set with the following menu: Options menu

3D Safety Precautions (see page 56) Power On Message (see page 55)

Selecting the input signal

Press to select the input signal to be played back from the equipment which has been connected to the Plasma Display.

Input signals will change as follows:

PC COMPONENT* DVIHDMIVIDEO

PC: PC input terminal in PC IN. VIDEO: Video input terminal in AV IN (VIDEO). COMPONENT*: Component or RGB input terminal in COMPONENT/RGB IN. HDMI: HDMI input terminal in AV IN (HDMI). DVI: DVI input terminal in DVI-D IN. * “COMPONENT” may be displayed as “RGB” depending on the setting of

“Component/RGB-in select”. (see page 48)

When an optional Terminal Board is installed: PC VIDEO HDMI DVICOMPONENTSLOT INPUT

SLOT INPUT: Input terminal in Terminal Board

Note:

When a Terminal Board incompatible with the Plasma Display is installed, “Non-Compatible Function Board” is displayed.

INPUT MENU ENTER/+/VOL-/

When a Terminal Board with dual input terminals is installed:

PC VIDEO HDMI DVICOMPONENTSLOT INPUT A SLOT INPUT B

SLOT INPUT A, SLOT INPUT B: Dual input terminal in Terminal Board.

Notes:

• Selecting is also possible by pressing the INPUT button on the unit.

• Outputs the sound as set in “Audio input select” in the Options menu. (see page 58)

• Select to match the signals from the source connected to the component/RGB input terminals. (see page 48)

• Image retention (image lag) may occur on the plasma display panel when a still picture is kept on the panel for an extended period. The function that darkens the screen slightly is activated to prevent image retention (see page 65), but this function is not the perfect solution to image retention.

Basic Controls

Main Unit

* The illustration is TH-65PF30ER.

Remote control sensor

Volume Adjustment

Volume Up “+” Down “–” When the menu screen is displayed: “+” : press to move the cursor up “–” :

press to move the cursor down

(see page 24)

INPUT MENU ENTER/

Main Power On / Off Switch

Power Indicator

The Power Indicator will light.

• Power-OFF .... Indicator not illuminated (The unit will

still consume some power as long as the power cord is still inserted into the wall outlet.)

• Standby ........ Red

Orange (When “Slot power” is set to “On”. See page 55) Orange (Depending on the type of the function board installed, when the power is supplied to the slot) Orange (When “Control I/F Select” is set to “LAN”. See page 52)

• Power-ON ...... Green

• PC Power management (DPMS)

.........................Orange (With PC input signal.

See page 41)

• DVI-D Power management

.........................Orange (With DVI input signal.

See page 41)

/VOL

MENU Screen ON / OFF

Each time the MENU button is pressed, the menu screen will switch. (see page 24)

Normal Viewing Picture

Sound Pos./Size Setup

INPUT button (INPUT signal selection)

(see page 17)

Enter / Aspect button

(see page 20, 24)

Remote Control Transmitter

ACTION button

Press to make selections.

ASPECT button

Press to adjust the aspect. (see page 20)

Standby (ON / OFF) button

The Plasma Display must ﬁ rst be plugged into the wall outlet and turned on at the power switch (see page 15). Press this button to turn the Plasma Display On, from Standby mode. Press it again to turn the Plasma Display Off to Standby mode.

POS./SIZE button

(see page 25)

Basic Controls

OFF TIMER button

The Plasma Display can be preset to switch to stand-by after a ﬁ xed period. The setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed.

30 min 60 min

0 min (Cancel)

When three minutes remain, “Off timer 3 min” will ﬂ ash. The off timer is cancelled if a power interruption occurs.

AUTO SETUP button

Automatically adjusts the position/ size of the screen. (see page 25)

SET UP button (see page 24)

90 min

PICTURE button (see page 28)

Sound mute On / Off Press this button to mute the sound. Press again to reactivate sound. Sound is also reactivated when power is turned off or volume level is changed.

N button (see page 27, 28, 29, 33)

POSITION buttons

INPUT button

Press to select Input signal sequentially. (see page 17)

SOUND button (see page 33)

Volume Adjustment

Press the Volume Up “+” or Down “–” button to increase or decrease the sound volume level.

R button (see page 24) Press the R button to return to previous menu screen.

RECALL button

Press the “RECALL” button to display the current system status.

Input label

Aspect mode (see page 20)

During 3D images (see page 35) Audio input (see page 58) Proﬁ le name (see page 32) NANODRIFT Saver operating

(see page 39)

Off timer

The off timer indicator is

displayed only when the off timer has been set.

Clock display (see page 55)

4:33D

COMPONENT

Memory name: MEMORY2

NANODRIFT

10:00

Off timer

90min

Digital Zoom (see page 21)

INPUT MENU ENTER/ +/ VOL -/

ASPECT Controls

The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format picture.

Note:

Be aware that if you put the display in a public place for commercial purposes or a public showing and then use the aspect mode select function to shrink or expand the picture, you may be violating the copyright under copyright law. It is prohibited to show or alter the copyrighted materials of other people for commercial purposes without the prior permission of the copyright holder.

Press repeatedly to move through the aspect options: For details about the aspect mode, please see “List of Aspect Modes” (page 66).

For VIDEO (S VIDEO) signal input:

4:3 Zoom1 16:9Zoom2 Zoom3 14:9 Just

[from the unit]

The aspect mode changes each time the ENTER button is pressed.

For PC signal input: For SD signal input (525 (480) / 60i • 60p, 625 (575) / 50i • 50p):

4:3 Zoom 16:9

4:3 Zoom1 16:9Zoom2 Zoom3 14:9 Just

For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i, 750 (720) / 60p • 50p]:

4:3

All Aspect mode

Set “All Aspect” to “On” in Options menu to enable the extended aspect mode (page 55). When All Aspect mode, the aspect mode of pictures is switched as follows. For details about the aspect mode, please see “List of Aspect Modes”. (page 66)

For VIDEO (S VIDEO) signal input:

4:3 Zoom1 16:9Zoom2 Zoom3 14:9 Just

For PC signal input:

4:3 Zoom

For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i, 750 (720) / 60p • 50p]:

4:3 Full Zoom1 16:9 Just1Zoom2 Zoom3 14:9 Just2 4:3 (1) 4:3 (2)

4:3 Full Zoom1

14:9Just

16:9

Zoom2

Zoom3

For SD signal input (525 (480) / 60i

4:3 Zoom1 16:9 JustZoom2 Zoom3 14:9

Notes:

• The aspect mode is memorized separately for each input terminal.

• Do not allow the picture to be displayed in 4:3 mode for an extended period, as this can cause a permanent image retention to remain on the Plasma Display Panel.

•

60p, 625 (575) / 50i

•

50p):

INPUT MENU ENTER/ +/ VOL -/

Digital Zoom

This displays an enlargement of the designated part of the displayed image.

Display the operation guide.

Press to access Digital Zoom. The operation guide will be displayed.

During Digital Zoom, only the following buttons can be operated.

[Remote control]

Select the area of the image to be enlarged.

Press on the enlargement location to select.

Exit

OFF TIMER button

[Unit]

VOL button

MUTE button

VOL button POSITION / ACTION button

The cursor will move.

Select the magniﬁ cation required for the enlarged display.

Each time this is pressed, the magniﬁ cation factor changes. This is shown in the image being displayed.

s1

Return to normal display (quit Digital Zoom).

Press to exit from the Digital Zoom.

Notes:

• When power goes OFF (including “Off Timer” operation), Digital Zoom terminates.

• The Digital Zoom function cannot be selected while in the following operation state: When MULTI DISPLAY Setup is On (see page 44). When Portrait Setup is On (see page 46). When Screensaver (except for Negative image) is running (see page 36)

• While Digital Zoom is in operation, “Adjusting Pos./Size” cannot be used.

s2

s3

Exit

s4

Viewing 3D images

You can enjoy viewing 3D images with contents or programmes compatible with 3D effect by using the 3D eyewear (optional).

Note:

You need the 3D IR TRANSMITTER (optional) and the 3D eyewear (optional) to view the 3D images on this display. For further information, see the instruction manuals of the 3D IR TRANSMITTER and the 3D eyewear.

This display supports “Frame Sequential

The 3D format that the images for the left and right eyes are recorded with the high deﬁ nition quality and alternately played back

2, *3: See “Table of images that can be seen for each 3D Picture Format and the source image format” on page 23.

4: To view “Simultaneous” 3D images, one of the following terminal boards should be installed:

Dual HD-SDI Terminal Board for 3D (TY-FB30DHD3D), Dual DVI-D Terminal Board for 3D (TY-FB30DD3D)

To view the 3D images

To view the contents of the Frame Sequential format (ex. 3D-compatible Blu-ray Disc, etc.) with 3D effect

Connect the 3D-compatible player via an HDMI cable (see page 10) and playback the contents.

• Use fully wired HDMI compliant cable.

• For the settings of the player, read the manual of the player.

• If you use the non 3D-compatible player, the images will be displayed without 3D effect.

To view the contents of 3D formats other than Frame Sequential with 3D effect.

Match the picture format in “3D Picture Format” (see page 35) before viewing.

• You can view “Side by Side” and “Top and Bottom” with 3D effect even if you use the non 3D-compatible player.

• Please consult the suppliers of contents or programmes for availability of this service.

Turn the 3D Eyewear on

• See the instruction manual of 3D eyewear for handling.

Put on the 3D Eyewear Watch the 3D images

”, “Side by Side*2”, “Top and Bottom*3” and “Simultaneous*4” 3D formats.

Notes:

• If the room is lit by ﬂ uorescent lights and light appears to ﬂ icker when using the 3D Eyewear, switch off the ﬂ uorescent light. Alternatively, please set “3D Refresh Rate” to “100Hz” or “120Hz” whichever reduces ﬂ icker.

(see page 50)

• 3D content will not be correctly visible if the 3D Eyewear is worn upside down or back-to-front.

• Do not wear the 3D Eyewear when watching anything other than 3D images. Liquid crystal displays (such as computer screens, digital clocks or calculators, etc.) may be difﬁ cult to see while wearing the 3D Eyewear.

• Do not use the 3D Eyewear as sunglasses.

• 3D effects may be perceived differently depending on the person.

+ 49 hidden pages