9.2 IIC mode structure (following items value is sample data.)
TOPPREVIOUSNEXT
SCHEMA*99
9.1 CAT (computer Aided Test) mode
TOPPREVIOUSNEXT
To exit the CAT mode, access the ID mode and switch off the main power.
9.1.1 IIC mode
9.1.2 CD mode
9.1.3 SD mode
TOPPREVIOUSNEXT
SCHEMA*99
9.1.1 IIC mode
TOPPREVIOUSNEXT
Select the IIC mode by Up/Down button on the remote control at the front page of CAT mode then
press the Action button on the remote control.
Subject and item are mentioned on page 14.
To exit the IIC mode, press the R button on the remote control.
TOPPREVIOUSNEXT
SCHEMA*99
9.1.2 CD mode
TOPPREVIOUSNEXT
Select the CD mode by Up/Down button on the remote control at the front page of CAT mode then
press the Mute button on the remote control more than 5 sec.
Micom software version (IC9354), this version can be upgrade by
1.replace of new version IC
2.Loading the new version software from loader tool, TZSC07036.
Memory data change
To exit the CD mode, press the R button on the remote control.
TOPPREVIOUSNEXT
SCHEMA*99
9.1.3 SD mode
TOPPREVIOUSNEXT
Select the SD mode by Up/Down button on the remote control at the front page of CAT mode then
press the Action button on the remote control.
To exit the SD mode, press the R button on the remote control.
TOPPREVIOUSNEXT
SCHEMA*99
9.2 IIC mode structure (following items value is
sample data.)
TOPPREVIOUSNEXT
TOPPREVIOUSNEXT
SCHEMA*99
11 Trouble shooting guide
TOPPREVIOUSNEXT
11.1 Self Check
11.1.1 Display Indication
11.1.2 Power LED Blinking timing chart
11.2 No Power
11.3 No Picture
11.4 Local screen failure
TOPPREVIOUSNEXT
SCHEMA*99
11.1 Self Check
TOPPREVIOUSNEXT
11.1.1 Display Indication
11.1.2 Power LED Blinking timing chart
TOPPREVIOUSNEXT
SCHEMA*99
11.1.1 Display Indication
button on the customer controls at the
Note:
TOPPREVIOUSNEXT
1.Self-check is used to automatically check the bus line controlled circuit of the Plasma display.
2.To get into the Self-check mode, press the volume down
front of the set, at the same time pressing the OFF-TIMER button on the remote control, and
the screen will show :-
If the CCU ports have been checked and found to be incorrect
Or not located then " - - " will appear in place of " OK "
In case of disconnected of H/HY/HZ “IC3699 - -” is displayed.
TOPPREVIOUSNEXT
SCHEMA*99
11.1.2 Power LED Blinking timing chart
TOPPREVIOUSNEXT
1.Subject
Information of LED Flashing timing chart.
2.Contents
When an abnormality has occurred the unit, the protection circuit operates and reset to the
stand by mode. At this time, the defective block can be identified by the number of blinkes of
the Power LED on the front panel of the unit.
3.Remarks
Above Fan function is operated during the fans are installed.
TOPPREVIOUSNEXT
SCHEMA*99
11.2 No Power
TOPPREVIOUSNEXT
[First check point]
There are following 3 states of No Power indication by power LED.
1.No lit
2.Green is lit then turns red blinking a few seconds later.
3.Only red is lit.
1.No lit
TOPPREVIOUSNEXT
SCHEMA*99
11.3 No Picture
TOPPREVIOUSNEXT
TOPPREVIOUSNEXT
SCHEMA*99
11.4 Local screen failure
TOPPREVIOUSNEXT
Plasma display may have local area failure on the screen. Fig - 1is the possible defect P.C.B. for
each local area.
Fig - 1
TOPPREVIOUSNEXT
SCHEMA*99
12 Option Setting
Note :
TOPPREVIOUSNEXT
Hidden Option Menu for GP5D series
GP5D chassis series have special function and operation setting facility called Option Menu. This
Option Menu is useful for special function required customers. This should be set at the installation
stage. The end user could not set or change these becauseof hidden On screen menu.
Option menus default
setting
Wobbling Off Wobbling operation On/Off.
The outline of burnt image will be blurred by intermittent image sift.
Off-timer function Enable Off-timer operation Enable/Disable.
On Screen display On Enable/Disable to display input mode indication after power on and no signal indication.
Initial Input Off Sets the initial input mode when the power is turned on . Allow input mode selection while power is on.
Initial VOL. level Off Sets the initial volume level when the power is turned on. Allow Volume control while power is on.
Maximum VOL.
Level
INPUT lock Off Fixes the input mode to AV, Component/RGB or PC. Can not change input mode by input selection key.
Button lock Off Enable/Disable front operation buttons (Input and/or volume up/down)
Studio W/B Off Set warm mode color temperature to 3,200 Kelvin.
Remocon User Level Off Remote key invalidation.
Off Sets the maximum volume to desired level. Volume cannot exceed this level.
Off : Valid key is all key of remote.
User1 : Valid key are only Stand-by (ON/OFF), Input, Status, Surround, Sound mute On/Off, and volume
adjustment.
User2: Valid key is only Stand-by (ON/OFF).
User3 : All keys are null and void
Contents
ID Select 0 to 100 Set ID number from 001 to 100.
Remote ID Off Remote ID function On/Off.
(While the Remote ID on, standard remote function can not control the unit.)
Serial Off Serial ID function On/Off
How to set Remocon User Level and Remote ID off
1.Access service mode (CAT-mode) and press SET UP key on remote.
2.Accsess Hidden option menu.
3.Change Remocon User Level and/ or Remote ID set to Off.
TOPPREVIOUSNEXT
SCHEMA*99
18 Schematic Diagram for printing with A4
TOPPREVIOUS
TOPPREVIOUS
SCHEMA*99
14 Block and Schematic Diagrams
14.1.Schematic Diagram Notes
Important Safety Notice
Components identified by mark have special characteristics important for safety.
When replacing any of these components, use only manufacture's specified parts.
Notes:
1. Resistor
All resistors are cabon 1/4W resistor, unless marked as follows:
Unit of resistance is OHM [W] (K=1,000, M=1,000,000).
: Nonflammable: Metal Oxide
: Solid: Metal Film
: Wire Wound: Fuse:
2. Capacitor
All capacitors are ceramic 50V capacitor, unless marked as follows:
Unit of capacitance is mF, unless otherwise noted.
: Temperature Compensation: Electrolytic
: Polyester: Bipolar
1. The Power Circuit contains a circuit area which uses a separate power supply to isolate the
earth connection.
The circuit is defined by HOT and COLD indications in the schematic diagram. Take the
follwing precautions.
All circuits, except the Power Circuit, are cold.
Precautions
a. Do not touch the hot part or the hot and cold parts at the same time or you may
be shocked.
b. Do not short- circuit the hot and cold circuits or a fuse may blow and parts may
break.
c. Do not connect an instrument, such as an oscilloscope, to the hot and cold
circuits simultaneously or a fuse may blow.
Connect the earth of instruments to the earth connection of the circuit being
measured.
d. Make sure to disconnect the power plug before removing the chassis.