Panasonic TH-37PWD6UX User Manual

Operating Instructions

PLASMA DISPLAY

Progressive Wide Plasma Display

R E T

N E

L O V

–

N E M

U P N I

Y B D

N A

R E

O P

O P G

Model No.

TH-37PWD6UX TH-42PWD6UX

Before connecting, operating or adjusting this product, please read these instructions completely . Please keep this manual for future reference.

English

TQBC0650

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: To reduce the risk of electric shock, do not remove cover or back. No user-serviceable parts inside. Refer servicing to qualified service personnel.

The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons.

WARNING: To prevent damage which may result in fire or shock hazard, do not expose this apparatus to rain

or moisture. Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set. (including on shelves above, etc.)

WARNING: 1) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to

qualified service personnel.

2) Do not remove the grounding pin on the power plug. This apparatus is equipped with a three pin grounding-type power plug. This plug will only fit a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug.

The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance.

Important Safety Instructions

1) Read these instructions. All the safety and operating instructions should be read before the appliance is operated.

2) Keep these instructions. The safety and operating instructions should be retained for future reference.

3) Heed all warnings. All warnings on the appliance and in the operating instructions should be adhered to.

4) Follow all instructions. All operating and use instructions should be followed.

5) Do not use this apparatus near water. For example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

6) Clean only with dry cloth. Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Slots and Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments / accessories specified by the Manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from tip-over. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

13) Unplug this apparatus during lightning storms or when unused for long periods of time. This will prevent damage to the product due to lightning and power-line surges.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15) To prevent electric shock, ensure the grounding pin on the AC cord power plug is securely connected.

Dear Panasonic Customer

Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new Plasma Display. To obtain maximum benefit from your set, please r ead these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt as well, and record the model number and serial number of your set in the space provided on the rear cover of these instructions.

Important Safety Instructions ...................................... 3

FCC STATEMENT .......................................................... 5

Safety Precautions........................................................ 6

Accessories ................................................................... 8

Accessories Supplied...................................................8

Remote Control Batteries.............................................8

Connections .................................................................. 9

PC Input Terminals connection .................................. 10

SERIAL Terminals connection.................................... 11

Power ON/OFF............................................................. 12

AC cord conncection.................................................. 12

Power ON/OFF .......................................................... 12

Input Signal Selection................................................. 13

Select the Input Signal ............................................... 13

Selecting the ON-Screen Menu Language ................ 13

Basic Controls............................................................. 14

On-Screen Menu Displays.......................................... 16

ASPECT Controls........................................................ 18

Adjusting PICTURE POSITION/SIZE.......................... 19

SOUND Adjustment .................................................... 20

MUTE ......................................................................... 20

PICTURE Adjustments................................................ 21

ADVANCED SETTINGS ............................................22

PRESENT TIME SETUP/SET UP TIMER ....................23

PRESENT TIME SETUP............................................23

SET UP TIMER.......................................................... 24

SCREENSAVER (For preventing after-images) ........ 25

Setup of SCREENSAVER Time................................. 26

Reduces screen after-image...................................... 26

SIDE BAR ADJUST ................................................... 27

Digital Zoom ................................................................ 28

Reduces power consumption .................................... 29

Customizing the Input labels...................................... 29

SET UP for MULTI DISPLAY ....................................... 30

How to setup MULTI DISPLAY................................... 30

How to set the Display location number for each Plasma Display ....

SET UP for Input Signals............................................ 32

COMPONENT/RGB IN SELECT ............................... 32

3D Y/C FILTER – For NTSC Video images........................32

COLOR SYSTEM / Panasonic AUTO ........................33

3:2 PULLDOWN.........................................................33

SYNC .........................................................................34

H-FREQ. (kHz)/V-FREQ. (Hz) ................................... 34

Troubleshooting.......................................................... 35

Input signal can be displayed .................................... 36

Specifications.............................................................. 37

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

•

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution:

To assure continued compliance and possible undesirable interference, the provided ferrite cores must be used when connecting this plasma display to video equipment; and maintain at least 40 cm spacing to other peripheral devices. Any changes or modifications not expressly approved by Matsushita Electric Corporation of America could cause harmful interference and would void the user's authority to operate this device.

FCC Declaration of Conformity

Responsible Party: Matsushita Electric Corporation of America

One Panasonic Way, Secaucus, NJ 07094

Contact Source: Panasonic Consumer Electronics Company

1-888-843-9788 email: consumerproducts@panasonic.com

Attach the ferrite core:

The ferrite cores provided as a supplied accessory must be used when connecting this Plasma Display to video equipment. (see page 10, 11)

CANADIAN NOTICE:

This Class B digital apparatus complies with Canadian ICES-003.

Note:

Do not allow a still picture to be displayed for an extended period, as this can cause permanent after-image to remain on the Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.

Trademark Credits

VGA is a trademark of International Business Machines Corporation.

•

Macintosh is a registered trademark of Apple Computer, USA.

•

S-VGA is a registered trademark of the Video Electronics Standard Association.

•

Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected.

Safety Precautions

WARNING

Set up

Do not place the Plasma Display on sloped or unstable surfaces.

The Plasma Display may fall off or tip over.

•

Do not place any objects on top of the Plasma Display.

If water spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in fire

•

or electric shock. If any foreign objects get inside the Plasma Display, please consult an Authorized Service Center.

Do not cover the ventilation holes.

Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display.

•

If using the pedestal (optional accessory), leave a space of 3 15/16” (10 cm) or more at the top, left and right, 2 3/8” cm) or more at the bottom, and 2 3/4” (7 cm) or more at the rear. If using some other setting-up method, leave a space of 3 15/16” (10 cm) or more at the top, bottom, left and right, and 3/4” (1.9 cm) or more at the rear.

Avoid installing this product near electronic equipment that easily receives electromagnetic waves.

It may cause interference in image, sound, etc. In particular, keep video equipment away from this product.

•

AC Power Supply Cord

The Plasma Display is designed to operate on 120 V AC, 50/60 Hz.

Securely insert the power cord plug as far as it will go.

If the plug is not fully inserted, heat may be generated which could cause fire. If the plug is damaged or the wall socket

•

plate is loose, they should not be used.

Do not handle the power cord plug with wet hands.

Doing so may cause electric shocks.

•

Do not do anything that might damage the power cable. When disconnecting the power cable, hold the plug, not the cable.

Do not make any modifications, place heavy objects on, place near hot objects, heat, bend, twist or forcefully pull the

•

power cable. Doing so may cause damage to the power cable which can cause fire or electric shock. If damage to the cable is suspected, have it repaired at an Authorized Service Center.

If the Plasma Display will not be used for a long period of time, unplug the power cord from the wall outlet.

If problems occur during use

If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected from the Plasma Display, unplug the power cord immediately.

Continuous use of the Display under these conditions might cause fire or permanent damage to the unit. Have the

•

Display evaluated at an Authorized Service Center. Services to the Display by any unauthorized personnel are strongly discouraged due to its high voltage dangerous nature.

If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet becomes damaged, disconnect the power cord plug immediately.

A short may occur, which could cause fire. Contact an Authorized Service Center for any repairs that need to be made.

•

Safety Precautions

CAUTION

This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury.

(All of the following accessories are manufactured by Matsushita Electric Industrial Co., Ltd.)

Speakers ........................................................TY-SP37P5W-K (TH-37PWD6UX)

•

Pedestal ......................................................... TY-ST05-K

•

Wall stand....................................................... TY-ST42PW1

•

Wall-hanging bracket (vertical).......................TY-WK37PV3 (TH-37PWD6UX)

•

Ceiling unit ......................................................TY-CE42PS1

•

Tuner Connection Terminal Board ...................TY-42TM6H

•

RCA Composite V ideo Terminal Board ............ TY-42TM6V

•

RCA Component V ideo Terminal Board........... TY-42TM6Z

•

Always be sure to ask a qualified technician to carry out set-up.

When using the Plasma Display

Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display.

Top of the Plasma Display is usually very hot due to the high temperature of exhaust air being released through the

•

ventilation holes. Burns or personal injuries can happen if any body parts are brought too close. Placing any object near the top of the display could also result in heat damages to the object as well as to the Display if its ventilation holes are blocked.

TY-SP42P5W-K (TH-42PWD6UX)

TY-WK42PV1 (TH-42PWD6UX)

Be sure to disconnect all cables before moving the Plasma Display.

Moving the Display with its cables attached might damage the cables which, in turn, can cause fire or electric shock.

•

Disconnect the power plug from the wall outlet as a safety precaution before carrying out any cleaning.

Electric shocks can result if this is not done.

•

Clean the power cable regularly to prevent it from becoming dusty.

Built-up dust on the power cord plug can increase humidity which might damage the insulation and cause fire. Unplug

•

the cord from the wall outlet and clean it with a dry cloth.

This Plasma Display radiates infrared rays, therefore it may affect other infrared communication equipment. Install your infrared sensor in a place away from direct or reflected light from your Plasma Display.

Cleaning and maintenance

The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth.

If the surface is particularly dirty, soak a soft, lint-free cloth in a weak detergent solution and then wring the cloth to

•

remove excess liquid. Use this cloth to wipe the surface of the display panel, then wipe it evenly with a dry cloth, of the same type, until the surface is dry. Do not scratch or hit the surface of the panel with fingernails or other hard objects. Furthermore, avoid contact with volatile

•

substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected.

If the cabinet becomes dirty, wipe it with a soft, dry cloth.

If the cabinet is particularly dirty , soak the cloth in a weak detergent solution and then wring the cloth dry. Use this cloth

•

to wipe the cabinet, and then wipe it dry with a dry cloth. Do not allow any detergent to come into direct contact with the surface of the Plasma Display.

•

If water droplets get inside the unit, operating problems may result. Avoid contact with volatile substances such as insect sprays, solvents and thinner , otherwise the quality of the cabinet

•

surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC.

Note:

Do not allow a still picture to be displayed for an extended period, as this can cause a permanent after-image to remain on the Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.

PLASMA DISPLAY

INPUT

SURROUND

VOL

PICTURE

SOUND

SET UP

ASPECT

PICTURE POS. /SIZE

OFF TIMER

MULTI

PIP

SWAP SELECT

ZOOM MOVE

Accessories

Accessories Supplied

Check that you have the Accessories and items shown

Operating Instruction book

Remote Control Transmitter EUR646529

Ferrite core (small size) × 1

Ferrite core (large size) × 2

Remote Control Batteries

Requires two AA batteries.

1. Turn the transmitter face down. Press and slide off the battery cover.

2. Install the batteries as shown in the battery compartment.

(Polarity + or – must match the

markings in the compartment.)

AC cordBatteries for the Remote Control Transmitter (AA Battery × 2)

Fixing bands

3. Replace the cover and slide in reverse until the lock snaps.

Two "AA" size

Helpful Hint:

For frequent remote control users, replace old batteries with Alkaline batteries for longer life.

Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.

Observe the following precautions:

1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.

2. Do not combine a used battery with a new one.

3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).

4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

5. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display.

Connections

When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation.

Speakers (Optional accessories)

SPEAKERS Terminals (R)

AC cord connection (see page 12)

– AC cord fixing

1. Open the clamper.

Clamper

Note: The power plug in the illustration may not be the type fitted to your set.

– Cable fixing bands

Secure any excess cables with bands as required.

Pass the attached cable fixing band through the clip as shown in the figure.

To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure.

While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band.

2. Insert the AC cord and

close the clamper securely.

AC cord

SPEAKERS Terminals (L)

To tighten:

Pull

3. Slide up the clamper and fix the AC cord plug securely.

When loosen the clamper:

To loosen:

Push the catch

Optional Terminal Board insert Slots (covered)

SLOT1 SLOT2

AUDIO

SLOT3

From EXTERNAL monitor terminal on Computer (see page 10)

Pull

SERIALPC IN

From SERIAL Terminal on Computer (see page 11)

Connections

67839

1514131211

PC Input Terminals connection

COMPUTER

R - STANDBY G POWER ON

Conversion adapter (if necessary)

Connect a cable which matches the audio output terminal on the computer.

Installing the ferrite core (Small size)

Less than

(10 cm)

Ferrite core (small size)

Audio

(supplied)

Open

VOL

INPUTMENU ENTER

– +

Ferrite core (large size) (supplied)

RGB

PC cable

Less than

3" (10 cm)

AUDIO

PC IN

D-sub 15p

Stereo plug

Pull back the tabs (in two places)

Installing the ferrite core (Large size)

Pull back the tabs (in two places)

Open

Press the cable through and close

Notes:

(1) Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical

scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

(2) The display resolution is a maximum of 640 × 480 dots when the aspect mode is set to “4:3”, and 852 × 480 dots

when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity.

(3) The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible,

you will need to make setting changes to the computer at the time of connection. (4) Some PC models cannot be connected to the set. (5) There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal. (6) The computer shown in the illustration is for example purposes only. (7) Additional equipment and cables shown are not supplied with this set. (8) Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified

frequency range. (9) Component Input is possible with the pin 1,2,3 of the D-sub 15P Connector.

Signal Names for D-sub 15P Connector

Signal Name

R (PR/CR)

G(Y)

B(PB/CB) GND (Ground) GND (Ground)

Pin No.

6 7 8 9

Signal Name GND (Ground) GND (Ground) GND (Ground)

NC (not connected)

GND (Ground)

Pin No.

11 12 13 14 15

Signal Name

GND (Ground)

SDA

HD/SYNC

SCL

Pin Layout for PC Input Terminal

Pin No.

1 2 3 4 5

Connections

SERIAL Terminals connection

The SERIAL terminal is used when the Plasma Display is controlled by a computer.

COMPUTER

RS-232C Straight cable

Ferrite core (large size) (supplied)

SERIAL

Pin layout for RS-232C

Installing the ferrite core

(Large size)

D-sub 9p

Less than

/16

(10 cm)

Notes:

(1) Use the RS-232C cable to connect the computer to the Plasma Display. (2) The computer shown is for example purposes only. (3) Additional equipment and cables shown are not supplied with this set.

The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled by a computer which is connected to this terminal. The computer will require software which allows the sending and receiving of control data which satisfies the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details.

9876

53214

Open

Communication parameters

Signal level

Synchronization method

Baud rate

Parity

Character length

Stop bit

Flow control

RS-232C compliant

Asynchronous

9600 bps

None 8 bits

1 bit

–

Basic format for control data

The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent.

STX

Start (02h)

Colon Parameter(s)

3-character command (3 bytes)

(1 - 5 bytes)

ETX:C2C1 C3 P2P1 P3 P4 P5

End (03h)

Notes:

(1) If multiple commands are transmitted, be sure to wait

for the response for the first command to come from this unit before sending the next command.

(2) If an incorrect command is sent by mistake, this unit will

send an “ER401” command back to the computer.

RS-232C Conversion cable

D-sub 9-pin female

2 3 5

4 • 6

7 8

1 • 9

Details

R X D T X D

GND

Non use

Shorted

Command

Command PON POF AVL

AMT IMS

DAM

Parameter None None

0 1 None SL1 SL2 SL3 PC1 None NORM ZOOM FULL JUST SELF

Power ON Power OFF Volume 00 - 63 Audio MUTE OFF Audio MUTE ON Input select (toggle) Slot1 input Slot2 input Slot3 input PC input Screen mode select (toggle) NORMAL (4:3) ZOOM FULL JUST Panasonic AUTO

Control details

With the power off, this display responds to PON command only.

Power ON/OFF

AC cord connection

Connecting the AC cord plug to the Plasma Display.

Power ON/OFF

VOL

INPUTMENU ENTER

– +

R - STANDBY G POWER ON

Fix the AC cord plug securely to the Plasma Display with the clamper.

Connecting the plug to the Wall Outlet

Press the POWER switch on the Plasma Display to turn the set on : POWER-ON.

Power Indicator : Green

R - STANDBY G POWER ON

TH-42PWD6

Power Indicator

Remote Control Sensor

When the POWER is turned on for the first time, the LANGUAGE selection screen is displayed.

From the second time on, language selection can be done from the setup menu. (see page 13)

Select the desired language using the

and

keys and press the ACTION

button.

SURROUND

INPUT

OSD LANGUAGE

English (UK

Deutsch Fran ais

Italiano

a ol

ENGLISH (US

SELECT

Example: The screen below is displayed for a while after

the Plasma Display is turned on. (setting condition is an example.)

From the second time on, the screen shown

)

SET

Press the

below is displayed for a while (setting

condition is an example).

NORMAL

button on the remote control to turn the

Plasma Display off.

Power Indicator: Red (STAND-BY)

Press the

button on the remote control to turn the

Plasma Display on.

Power Indicator: Green

VOL

Note: During operation of the power management function, the power

indicator turns orange in the power off state.

T o turn the power for the Plasma Display off, press the

switch on the Plasma Display, when the Plasma Display is on or in standby mode.

+ 28 hidden pages

Panasonic TH-37PWD6UX User Manual

Important Safety Instructions

Table of Contents

FCC STATEMENT

Safety Precautions

Accessories

Accessories Supplied

Remote Control Batteries

Connections

SERIAL Terminals connection

Power ON/OFF

AC cord connection

Power ON/OFF