Panasonic SC-HC49EG-K, SC-HC49EG-S User Manual

Operating Instructions Instrukcja obsługi Návod k obsluze

Instrucciones de funcionamiento

Compact Stereo System Kompaktowy zestaw stereo Kompaktní stereo systém Sistema estéreo compacto

Model No. SC-HC49

Thank you for purchasing this product.

Please read these instructions carefully before using this product, and save this manual for future use.

Included Installation Instructions (l 2 and 18, 19)

The installation work should be done by a qualified installation specialist.

Before commencing work, carefully read these installation instructions and the operating instructions to ensure that installation is performed correctly. (Please keep these instructions. You may need them when maintaining or moving this unit.)

Dziękujemy za zakupienie tego produktu.

Przed przystąpieniem do eksploatacji opisywanego produktu należy dokładnie przeczytać niniejsze zalecenia i zachować instrukcję obsługi do wglądu.

Załączone instrukcje instalacji (l 22 i 38, 39)

Instalację powinien przeprowadzić wyłącznie wykwalifikowany specjalista.

Przed rozpoczęciem pracy należy się dokładnie zapoznać z instrukcją instalacji oraz z instrukcją obsługi, aby się upewnić, że instalacja została przeprowadzona prawidłowo.

(Proszę zachować niniejszą instrukcję. Będzie ona potrzebna podczas serwisowania lub przenoszenia urządzenia.)

Děkujeme, že jste si zakoupil tento výrobek.

Před použitím tohoto produktu si pečlivě přečtěte tyto pokyny a celý návod si uložte pro pozdější použití.

Přiložené pokyny k instalaci (l 42 a 58, 59)

Instalační práce musí být provedeny kvalifikovaným instalatérským odborníkem.

Před zahájením instalace si pečlivě pročtěte tyto pokyny k instalaci a návod k obsluze, abyste instalaci provedli opravdu správně.

(Tyto pokyny si uschovejte. Můžete je potřebovat při údržbě nebo přesouvání tohoto zařízení.)

Muchísimas gracias por haber adquirido este aparato. Lea cuidadosamente estas instrucciones antes de usar este producto, y guarde este manual para usarlo en el futuro.

Se incluyen instrucciones de instalación (l 62 y 78, 79)

La instalación debe ser realizada por un especialista calificado.

Antes de comenzar la instalación, lea cuidadosamente estas instrucciones de instalación y el manual de instrucciones para asegurarse de que la instalación se realice correctamente.

(Conserve estas instrucciones. Puede necesitarlas al momento de realizar mantenimiento o trasladar esta unidad)

	EG	RQT9886-3R

ENGLISH

POLSKI

ČESKY

ESPAÑOL

Safety precautions

WARNING

Unit

≥To reduce the risk of fire, electric shock or product damage,

–Do not expose this unit to rain, moisture, dripping or splashing.

–Do not place objects filled with liquids, such as vases, on this unit.

–Use only the recommended accessories.

–Do not remove covers.

–Do not repair this unit by yourself. Refer servicing to qualified service personnel.

–Do not let metal objects fall inside this unit.

–Do not place heavy items on this unit.

AC mains lead

≥To reduce the risk of fire, electric shock or product damage,

–Ensure that the power supply voltage corresponds to the voltage printed on this unit.

–Insert the mains plug fully into the socket outlet.

–Do not pull, bend, or place heavy items on the lead.

–Do not handle the plug with wet hands.

–Hold onto the mains plug body when disconnecting the plug.

–Do not use a damaged mains plug or socket outlet.

≥The mains plug is the disconnecting device.

Install this unit so that the mains plug can be unplugged from the socket outlet immediately.

CAUTION

Unit

≥This unit utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

≥Do not place sources of naked flames, such as lighted candles, on this unit.

≥This unit may receive radio interference caused by mobile telephones during use. If such interference occurs, please increase separation between this unit and the mobile telephone.

≥This unit is intended for use in moderate climates.

Placement

≥Place this unit on an even surface.

≥To reduce the risk of fire, electric shock or product damage,

–Do not install or place this unit in a bookcase, built-in cabinet or in another confined space. Ensure this unit is well ventilated.

–Do not obstruct this unit’s ventilation openings with newspapers, tablecloths, curtains, and similar items.

–Do not expose this unit to direct sunlight, high temperatures, high humidity, and excessive vibration.

2

Battery

≥Danger of explosion if battery is incorrectly replaced. Replace only with the type recommended by the manufacturer.

≥Mishandling of batteries can cause electrolyte leakage and may cause a fire.

–Remove the battery if you do not intend to use the remote control for a long period of time. Store in a cool, dark place.

–Do not heat or expose to flame.

–Do not leave the battery(ies) in a car exposed to direct sunlight for a long period of time with doors and windows closed.

–Do not take apart or short circuit.

–Do not recharge alkaline or manganese batteries.

–Do not use batteries if the covering has been peeled off.

≥When disposing of the batteries, please contact your local authorities or dealer and ask for the correct method of disposal.

NORSK

ADVARSEL

Produkt

≥For å redusere faren for brann, elektrisk støt eller skade på apparatet:

–Utsett ikke produktet for regn, fukt, drypping eller sprut.

–Ikke plasser objekter som er fylt med væske, som vaser, på apparatet.

–Bruk kun anbefalt tilbehør.

–Fjern ikke deksler.

–Reparer ikke denne enheten selv, overlat service til kvalifisert servicepersonell.

Vekselstrømnett

≥Nettstøpselet er trukket ut fra denne enheten.

Installer denne enheten slik at nettstøpselet umiddelbart kan trekkes fra stikkontakten.

FORSIKTIG

Produkt

≥Dette produktet anvender en laser. Betjening av kontroller eller justering eller andre inngrep enn de beskrevet i denne bruksanvisning kan føre til farlig bestråling.

≥Plasser ikke åpen ild, slik som levende lys, oppå apparatet.

≥Dette apparatet er beregnet for bruk under moderate klimaforhold.

Plassering

≥For å redusere faren for brann, elektrisk støt eller skade på apparatet:

–Ikke plasser apparatet i en bokhylle, et innebygget kabinett eller et annet lukket sted. Pass på at produktet er godt ventilert.

–Apparatets ventilasjonsåpninger må ikke dekkes til med aviser, duker, gardiner eller lignende.

Product Identification Marking is located on the bottom of the unit.

RQT9886

Table of contents
Safety precautions............................................	2
Accessories.......................................................	3
Control reference guide ...................................	4
Connections ......................................................	5
Inserting media .................................................	6
Bluetooth® operations ......................................	7
Media playback controls ..................................	9
Listening to the radio .....................................	10
Sound adjustment ..........................................	11
Clock and Timer..............................................	11
Others ..............................................................	12
Troubleshooting..............................................	13
Unit and media care........................................	15
About Bluetooth® ............................................	16
Playable media................................................	16
Licenses ..........................................................	17
Attaching the unit to a wall (optional)...........	18
Specifications..................................................	20
Attaching the support pad to this unit..........	21

About descriptions in these operating instructions

≥Pages to be referred to are indicated as “l ±±”.

≥Unless otherwise indicated, operations are described using the remote control.

Accessories

Check the supplied accessories before using this unit.

∏1 Remote control

(N2QAYB000945)

∏1 Battery for remote control

∏1 AC mains lead

∏ 1 FM indoor antenna
∏ 1	(support pad)	ENGLISH
	Pad sheet
Wall mounting accessories
∏ 1	Safety holder	∏ 2 Wall mount
		brackets

∏ 1 Screw

≥Do not use AC mains lead with other equipment.

≥Product numbers provided in these operating instructions are correct as of December 2013. These may be subject to change.

Disposal of Old Equipment and Batteries

Only for European Union and countries with recycling systems

These symbols on the products, packaging, and/or accompanying documents mean that used

electrical and electronic products and batteries must not be mixed with general household

waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment.

For more information about collection and recycling, please contact your local municipality. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

Note for the battery symbol (bottom symbol):

This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.

3

RQT9886

Control reference guide

1											Standby/on switch (Í/I) (Í)
Top view											Press to switch the unit from on to standby mode or vice
											versa.
											In standby mode, the unit is still consuming a small
											amount of power.
										2 Select the audio source
											On this unit:
											“CD” ------------. “BLUETOOTH” ------------. “IPOD_DOCK”
											^"""--"" “FM” ,"""--"" “USB”* ,"""--"}
											On the remote control:
											[ ]: “BLUETOOTH”
											[iPod/USB]: “IPOD_DOCK” ,. “USB”*
											[CD/RADIO]: “CD” ,. “FM”

3 Basic playback control buttons

4 Adjust the volume (0 (min) to 50 (max))

5 Open or close the sliding door

6 Bluetooth®-pairing button

≥ Press to select “BLUETOOTH” as the audio source.

≥ Press and hold to enter pairing mode (l 7) or

7

disconnect a Bluetooth® device (l 8).

NFC touch area (l 7)

8

Port for iPhone/iPad/iPod and USB devices (l 6)

Select “USB”* as the audio source.

9

Remote control signal sensor

Distance: Within approx. 7 m directly in front

10

Angle: Approx. 30o left and right

Display

11

Sliding door

12

Dock for iPhone/iPod

Select “IPOD_DOCK” as the audio source.

13

Enter setup menu

14

Enter the iPhone/iPod menu /

Change the displayed information

15

Enter sound menu

16

Dim the display panel

Press again to cancel.

17

Mute the sound

Press again to cancel. “MUTE” is also cancelled when the

18

volume is adjusted or the unit is turned off.

Enter playback menu

19

Selection/OK

* The display will automatically change to “IPOD_PORT” when a compatible iPhone/iPad/iPod is connected to the port for iPhone/iPad/iPod.

∫ Using the remote control

Insert the battery so the terminals (i and j) match those in the remote control.

Point it at the remote control signal sensor on this unit.

≥To avoid interference, please do not put any objects in front of signal sensor.

4

(Alkaline or manganese battery)

RQT9886

Connections

1Connect the antenna.

		Adhesive tape
		(not supplied)
		FM indoor antenna
		(supplied)
		Connect the AC mains lead after all other connections are completed.
	2
		This unit consumes a small amount of AC power (l 20) even when turned off.
		≥ In the interest of energy conservation, if you will not be using this unit for an extended period of time,

unplug it from the mains socket.

To a mains socket

AC mains lead (supplied)

ENGLISH

≥These speakers do not have magnetic shielding. Do not place them near a TV, personal computer or other magnetic devices.

≥Tape the antenna to a wall or column in a position with the least amount of interference.

≥If radio reception is poor, use a FM outdoor antenna with a right angle type connector (not supplied).

5

RQT9886

Inserting media

∫ Connecting an iPhone/iPad/iPod* or USB device

When you connect a compatible device to the port or the dock during “USB” or “IPOD_DOCK” mode, the selector will automatically select the corresponding source for the device.

Press [iPod/USB] to select “USB”.

The display will automatically change to “IPOD_PORT” when a compatible iPhone/ iPad/iPod is connected to the port.

≥ When connecting an iPhone/iPad/iPod, use the dedicated USB cable (not supplied). ≥ Insert the USB device directly. Do not use any USB extension cable.

≥ Please disconnect the USB device if you finish using.

≥ Before removing the USB device, select a source other than “USB”.

∫ Inserting a CD

The label side

≥ Make sure to tilt the disc so as not to touch the sliding door. ≥ Do not open the sliding door manually.

Pad (supplied)

≥ Attach the pad before using the dock. (l 21)

∫ Connecting an iPhone/iPod* with Lightning connector

When you connect a compatible device to the port or the dock during “USB” or “IPOD_DOCK” mode, the selector will automatically select the corresponding source for the device.

Press [iPod/USB] to select “IPOD_DOCK”.

To close the dock

Press and hold [PUSH CLOSE] while closing the dock.

Lightning connector

≥Be sure to remove the iPhone/iPod from its case.

≥Make sure that the iPhone/iPod is fully inserted and its back is resting against the pad.

≥Make sure to hold the dock when removing the iPhone/iPod.

*Refer to “Playable media” for compatible models. (l 16)

∫ Charging an iPhone/iPad/iPod

During unit on, charging starts when an iPhone/iPad/iPod is connected to this unit.

≥To continue charging from the USB cable connection during standby mode, make sure the iPhone/iPad/iPod has started charging before turning the unit to standby mode.

≥During standby mode, charging will start as usual from the Lightning connector.

≥Check the iPhone/iPad/iPod to see if the battery is fully charged. (Once fully charged, remove the iPhone/iPad/iPod.)

6 ≥ Make sure that the unit does not fall when inserting or removing media.

≥ When moving this unit, be sure to remove all media and turn this unit to standby mode.

RQT9886

Bluetooth® operations

You can listen to the sound from the Bluetooth® audio device from this unit wirelessly.

≥Refer to the operating instructions of the Bluetooth® device for details.

≥If you intend to use an NFC (Near Field Communication)-compatible Bluetooth® device, proceed to “One-Touch Connection (Connecting by NFC)”.

Connecting via Bluetooth® menu

Preparation

≥Turn on the Bluetooth® feature of the device and place the device near this unit.

∫ Pairing with Bluetooth® devices

1 Press [] to select “BLUETOOTH”.

{. If “PAIRING” is indicated on the display, go to step 4.

To enter pairing mode*

2 Press [PLAY MENU] to select “PAIRING”.

3 Press [3, 4] to select “OK? YES” and then press [OK].

To pair with a device

4 Select “SC-HC49” from the Bluetooth® device’s Bluetooth® menu.

{. The name of the connected device is indicated on the display for a few seconds.

5 Start playback on the Bluetooth® device.

*You can also enter pairing mode by pressing and holding [ -PAIRING] on the unit.

∫ Connecting a paired Bluetooth® device

1 Press [] to select “BLUETOOTH”.

{. “READY” is indicated on the display.

2 Select “SC-HC49” from the Bluetooth® device’s Bluetooth® menu.

{. The name of the connected device is indicated on the display for a few seconds.

3 Start playback on the Bluetooth® device.

≥If prompted for the passkey, input “0000”.

≥You can register up to 8 devices with this unit. If a 9th device is paired, the device that has not been used the longest will be replaced.

≥This unit can only be connected to one device at a time.

≥When “BLUETOOTH” is selected as the source, this unit will automatically try and connect to the last connected Bluetooth® device.

One-Touch Connection (Connecting by NFC)

For NFC-compatible Bluetooth® devices (AndroidTM devices) only

Simply by touching an NFC (Near Field Communication)-compatible Bluetooth® device on the unit, you can complete all preparations, from registering a Bluetooth® device to establishing a connection.

Preparation

≥Turn on the NFC feature of the device.

≥Android device version lower than 4.1 requires the installation of the app “Panasonic Music Streaming” (free of charge).

1Enter “Panasonic Music Streaming” in the search box of Google PlayTM to search, and then select “Panasonic Music Streaming”.

2Start the app “Panasonic Music Streaming” on the device.

–Follow on-screen instructions on your device.

–Always use the latest version of the app.

1 Press [] to select “BLUETOOTH”.

2 Touch and hold your device on the NFC touch area of this unit []. (l 4)

Do not move the Bluetooth® device until it beeps, displays a message or reacts in some way.

Once the Bluetooth® device has reacted, move the device away from this unit.

≥ When the registration and connection of the Bluetooth® device is complete, the name of the connected device is indicated on the display for a few seconds.

≥ The location of the NFC touch area differs depending on the device. When a connection cannot be established even if your Bluetooth® device has touched the NFC touch area of this unit, change the position of the device. The condition may also improve if you download the dedicated app “Panasonic Music Streaming” and start it up.

3 Start playback on the Bluetooth® device.

≥If you touch another device to this unit, you can update the Bluetooth® connection. The previously connected device will be disconnected automatically.

≥When the connection is established, playback may start automatically depending on the type of device being used.

≥The One-Touch Connection may not work properly depending on the type of device being used.

ENGLISH

7

RQT9886

Bluetooth® transmission mode

You can change the transmission mode to prioritise transmission quality or sound quality.

Preparation

≥Press [] to select “BLUETOOTH”.

≥If a Bluetooth® device is already connected, disconnect it.

1 Press [PLAY MENU] repeatedly to select “LINK MODE”.

2 Press [3, 4] to select the mode and then press [OK].

MODE 1: Emphasis on connectivity MODE 2: Emphasis on sound quality

≥Select “MODE 1” if the sound is interrupted.

≥The factory default is “MODE 2”.

Bluetooth® input level

If the sound input level from the Bluetooth® device is too low, change the input level setting.

Preparation

≥ Connect a Bluetooth® device.

1 Press [PLAY MENU] repeatedly to select “INPUT LEVEL”.

2 Press [3, 4] to select the level and then press [OK].

“LEVEL 0” ,. “LEVEL i1” ,. “LEVEL i2”

^---------------------------------------------------------J

≥Select “LEVEL 0” if the sound is distorted.

≥The factory default is “LEVEL 0”.

8

RQT9886

Disconnecting a Bluetooth® device

1 While a Bluetooth® device is connected: Press [PLAY MENU] repeatedly to select “DISCONNECT?”.

2 Press [3, 4] to select “OK? YES” and then press [OK].

≥You can also disconnect the Bluetooth® device by pressing and holding [ -PAIRING] on the unit.

≥The Bluetooth® device will be disconnected if a different audio source (e.g., “CD”) is selected.

Media playback controls

The following marks indicate the availability of the feature.

[CD]: CD audio in CD-DA format and a CD that contains MP3 files (l 16)

[iPod]: Compatible iPhone/iPad/iPod (l 16) [USB]: USB devices containing MP3 files (l 16) [Bluetooth]: Connected Bluetooth® device

Preparation

≥Turn the unit on.

≥Insert the media or connect the Bluetooth® device.

≥Press [CD/RADIO], [iPod/USB] or [] to select the audio source.

≥When using iPhone/iPad/iPod, the operation may vary among those models.

Basic controls

([CD], [iPod], [USB], [Bluetooth])

Play	Press [1/;].
Stop	Press [∫].
	≥ [USB]: The position is memorised and
	“RESUME” is displayed.
Pause	Press [1/;].
	Press again to restart play.
Skip	Press [:/6] or [5/9] to skip
	track.
	[CD], [USB] Press [3] or [4] to skip
	the MP3 album.
Search	During play or pause, press and hold
	[:/6] or [5/9].
	≥ [iPod]: Backwards search is only within
	the current track.

∫[CD], [USB], [Bluetooth] To display information

Press [DISPLAY, iPod MENU] repeatedly.

	≥ To use this unit’s remote control with a Bluetooth® device, the
	Bluetooth® device must support AVRCP (Audio Video
	Remote Control Profile).
	Depending on the status of the device, some controls may
	not work.
	≥ Maximum number of displayable characters: approx. 30				ENGLISH
	≥ This unit supports ver. 1.0, 1.1 and 2.3 ID3 tags. Text data
	that is not supported will not be displayed or will be shown
	differently.
	≥ Album and track indication for MP3 files.
	“A _ _ _”:		MP3 album number.
	“T _ _ _”:		MP3 track number.

≥ “ _ ” stands for the album or track number.

“	”:	This indication is also used to refer to an album.
“	”:	This indication is also used to refer to a track.

∫[iPod] To navigate through the iPhone/ iPod music menu

[3, 4]: To navigate menu items. [OK]: To go to the next menu.

[DISPLAY, iPod MENU]: To return to the previous menu.

≥Depending on the model (e.g., iPod nano 7th generation, etc.), it may be necessary to select the album, artist, etc. on the iPhone/iPod.

≥Depending on the iOS version, this function may not be available.

9

RQT9886

Playback modes ([CD], [USB])

Select the playback mode.

1 Press [PLAY MENU] to select “PLAYMODE” or “REPEAT”.

2 Press [3, 4] to select the setting and then press [OK].

PLAYMODE

	OFF	Cancels the play mode setting.
	PLAYMODE
	1-TRACK	Only plays the selected track.
		≥ “1”, “	” is displayed.
		(Skip to the desired track.)
	1-ALBUM	Only plays the selected MP3 album.
		≥ “1”, “	” is displayed.
	RANDOM	Plays the contents randomly.
		≥ “RND” is displayed.
	1-ALBUM	Plays the tracks in the selected
	RANDOM	MP3 album randomly.
		≥ Press [3] or [4] to select the MP3
		album.
		≥ “1”, “	”, “RND” is displayed.
REPEAT
	ON REPEAT	Turns on repeat mode.
		≥ “`” is displayed.
	OFF	Turns off repeat mode.
	REPEAT

≥During random play, you cannot skip to the previous track.

≥The mode is cancelled when you open the sliding door.

10

Listening to the radio

You can preset up to 30 channels.

Preparation

≥Make sure that the antenna is connected. (l 5)

≥Turn the unit on.

≥Press [CD/RADIO] to select “FM”.

≥A station previously stored is overwritten when another station is stored in the same channel preset.

Presetting stations automatically

1 Press [PLAY MENU] to select “A.PRESET”.

2 Press [3, 4] to select “LOWEST” or “CURRENT” and then press [OK].

LOWEST:

To begin auto preset with the lowest frequency (FM 87.50).

CURRENT:

To begin auto preset with the current frequency.*

{.The tuner starts to preset all the stations it can receive into the channels in ascending order.

*To change the frequency, refer to “Manual tuning and presetting”.

Listening to a preset channel

1 Press [PLAY MENU] repeatedly to select “TUNEMODE”.

2 Press [3, 4] to select “PRESET” and then press [OK].

3 Press [:/6] or [5/9] to select the channel.

RQT9886

∫ Manual tuning and presetting

Select a radio broadcast.

1Press [PLAY MENU] repeatedly to select “TUNEMODE”.

2Press [3, 4] to select “MANUAL” and then press [OK].

3Press [:/6] or [5/9] to tune to the required station.

≥To start automatic tuning, press and hold [:/6] or [5/9] until the frequency starts scrolling. Tuning stops when a station is found.

To preset the channel

4While listening to the radio broadcast, press [OK].

5Press [3, 4] to select the channel and then press [OK].

∫ To improve FM sound quality

1While receiving FM broadcasts, press

[PLAY MENU] repeatedly to select “FM MODE”.

2Press [3, 4] to select “MONO” and then press [OK].

≥This setting can be preset and memorised. To do so, continue to step 4 of “Manual tuning and presetting”.

≥Select “STEREO” in step 2 to return to stereo broadcasts.

≥“MONO” is cancelled if the frequency is changed.

∫ To display the current FM signal status

While receiving FM signal, press [PLAY MENU] repeatedly to display “FM STATUS” and then press [OK].

“FM ST”:	The FM signal is tuned and in stereo.
“FM”:	There is no tuned signal or the FM signal
	is in monaural.

“FM MONO”: “MONO” is selected in step 2 of “To improve FM sound quality” (l above).

∫ To display RDS text data

Press [DISPLAY, iPod MENU] to display the text data.

≥ Each time you press the button:

“PS”:	Programme service
“PTY”:	Programme type
“FREQ”:	Frequency display

≥“STEREO” is displayed when this unit tunes to a stereo broadcast.

≥The unit can display the text data transmitted by the radio data system (RDS) available in some areas. (RDS displays may not be available if reception is poor.)

Sound adjustment

The following sound effects can be added to the audio output.

1 Press [SOUND] repeatedly to select the effect.

2 Press [3, 4] to select the setting and then press [OK].

“PRESET EQ”	“HEAVY” (heavy), “SOFT” (soft),
(Preset Equalizer)	“CLEAR” (clear), “VOCAL”		ENGLISH
	(vocal) or “FLAT” (flat/off).
	≥ The factory default is “HEAVY”.
“BASS” (Bass) or	Adjust the level (j4 to i4).
“TREBLE” (Treble)
“D.BASS”	“ON D.BASS” or “OFF D.BASS”.
(Dynamic Bass)	≥ The factory default is
	“ON D.BASS”.
“SURROUND”	“ON SURROUND” or
(Surround)	“OFF SURROUND”.

≥The factory default is “OFF SURROUND”.

≥You may experience a reduction in sound quality when these effects are used with some sources. If this occurs, turn the sound effects off.

Clock and Timer

Setting the clock

This is a 24-hour clock.

1 Press [SETUP] repeatedly to select “CLOCK”.

2 Press [3, 4] to set the time and then press [OK].

≥To display the clock, press [SETUP] repeatedly to select “CLOCK” and then press [OK] once. The time is displayed for 10 seconds.

(During standby, press [DISPLAY, iPod MENU] once.)

≥The clock is reset when there is a power failure or when the AC mains lead is removed.

≥Reset the clock regularly to maintain accuracy.

11

RQT9886

Play timer

You can set the timer so this unit turns on at a certain time every day.

Preparation

Set the clock.

∫ Setting the timer

1 Press [SETUP] repeatedly to select “TIMER ADJ”.

2 Press [3, 4] to set the starting time (“ON TIME”) and then press [OK].

3 Press [3, 4] to set the finishing time (“OFF TIME”) and then press [OK].

4 Press [3, 4] to select the music source* and then press [OK].

Others

Auto off function

As a factory default, this unit will turn to standby mode automatically if there is no sound and it is not being used for approximately 20 minutes.

To cancel this function

1 Press [SETUP] repeatedly to select “AUTO OFF”. 2 Press [3, 4] to select “OFF” and then press [OK].

≥To turn the function on, select “ON” in step 2.

≥This setting cannot be selected when “FM” is the source.

≥When connected to a Bluetooth® device, the function does not work.

∫ Turning the timer on

1Prepare the selected music source and set the desired volume.

2Press [SETUP] repeatedly to select “TIMER SET”.

3Press [3, 4] to select “SET” and then press [OK].

≥“F” is displayed.

≥To turn the timer off, select “OFF”.

4Press [Í] to turn the unit to standby mode.

≥To display the timer settings, press [SETUP] repeatedly to select “TIMER ADJ” and then press [OK] once.

The music source and volume will also be displayed if the timer is turned on.

≥During standby, if the timer is turned on, press [DISPLAY, iPod MENU] twice to display the settings.

≥This unit can be used as normal after the timer is set, however:

–Turn the unit to standby mode before the timer start time.

–Even if the audio source or the volume is changed, the timer will still use the audio source and volume that was set when the timer was turned on.

*“CD”, “USB”, “FM” and “IPOD_DOCK” can be set as the music source.

≥For timer music source through the port for iPhone/iPad/ iPod and USB devices, select “USB”.

Sleep timer

The sleep timer can turn the unit off after a set time.

1 Press [SETUP] to select “SLEEP”.

2 Press [3, 4] to set the time (in minutes) and then press [OK].

“SLEEP 30” ,. “SLEEP 60” ,. “SLEEP 90” ,. “SLEEP 120”

^	------------------. “OFF” (Cancel) (------------------	J

≥The remaining time is indicated on the unit’s display except when other operations are performed.

≥The play timer and sleep timer can be used together. The

12 sleep timer is always the main timer on the unit.

Bluetooth® standby

When “SC-HC49” is selected from a paired Bluetooth® device’s Bluetooth® menu, this unit will turn on automatically from standby mode and establish a Bluetooth® connection.

1 Press [SETUP] repeatedly to select “BLUETOOTH STANDBY”.

2 Press [3, 4] to select “ON” and then press [OK].

≥ To turn the function off, select “OFF” in step 2.

RQT9886

Changing the unit and remote control code

When other Panasonic equipment responds to the supplied remote control, change the remote control code.

1 Press [CD/RADIO] to select “CD”.

2 While pressing and holding [SELECTOR] on the unit, press and hold [CD/RADIO] on the remote control until the unit’s display shows “REMOTE 2”.

3 Press and hold [OK] and [CD/RADIO] on the remote control for at least 4 seconds.

≥To change the mode back to “REMOTE 1”, press [CD/RADIO] to select “CD” and then repeat the step 2 and 3 but replace [CD/RADIO] with [ ].

Software update

Occasionally, Panasonic may release updated software for this unit that may add or improve the way a feature operates. These updates are available free of charge.

For more details, refer to the following website. http://panasonic.jp/support/global/cs/

(This site is in English only.)

∫ Checking the software version

The version of the installed software is displayed.

Press [SETUP] repeatedly to select “SW VER.” and then press [OK].

≥ Press [OK] to exit.

Troubleshooting

Before requesting service, make the following checks. If you are uncertain about some of the check points, or if the solutions indicated in the following guide does not resolve the issue, then consult your dealer for instructions.

To return all settings to the factory defaults

When the following situations occur, reset the memory:

≥There is no response when buttons are pressed.

≥You want to clear and reset the memory contents.

1Disconnect the AC mains lead. (Wait for at least 3 minutes before proceeding to step 2.)

2While pressing and holding down [Í/I] on the unit, reconnect the AC mains lead.

≥Keep holding down [Í/I] until “---------” appears on the display.

3 Release [Í/I].

≥All the settings are returned to the factory defaults. You will need to reset the memory items.

General

Humming heard during playback.

≥If an AC mains lead or fluorescent lights are near the cords, then keep other appliances and cords away from the cables.

The unit does not work.

≥One of the unit’s safety devices may have been activated. Reset the unit as follows:

1Press [Í/I] on the unit to switch the unit to standby.

≥ If the unit does not switch to standby, press [Í/I] on the unit

for approximately 10 seconds. The unit is forcibly switched to standby. Alternatively, disconnect the AC mains lead, wait for at least 3 minutes, then reconnect it.

2Press [Í/I] on the unit to switch it on. If the unit still cannot be operated, consult the dealer.

MP3 cannot be read.

≥You may not be able to play MP3 if you have copied a multi-session disc that has no data between sessions.

≥When creating a multi-session disc, it is necessary to close the session.

≥The amount of data on the disc is too small. Set the amount of data to above 5 MB.

Remote control

The remote control does not work properly.

≥ The battery is depleted or inserted incorrectly. (l 4)

Disc

Incorrect display or play does not start.

≥Make sure that the disc is compatible with this unit. (l 16)

≥There is moisture on the lens. Wait for about an hour and then try again.

ENGLISH

13

RQT9886

USB

No response when [1/;] is pressed.

≥Disconnect the USB device and then reconnect it. Alternatively, turn the unit off and on again.

The USB drive or its contents cannot be read.

≥The USB drive format or its contents is/are not compatible with the unit (l 16).

≥The USB host function of this product may not work with some USB devices.

Slow operation of the USB flash drive.

≥Large file size or high memory USB flash drive takes longer time to read.

The elapsed time displayed is different from the actual play time.

≥Copy the data to another USB device or backup the data and reformat the USB device.

Radio

Static or noisy reception is heard while listening to a radio broadcast.

≥Confirm the antenna is properly connected. (l 5)

≥Adjust the position of the antenna.

≥Try to keep a certain amount of distance between the antenna and AC mains lead.

≥Try using an outdoor antenna if there are buildings or mountains nearby. (l 5)

≥Turn the TV or other audio players off or separate it from this unit.

≥Keep this unit away from mobile phones if there is interference.

iPhone/iPad/iPod

Cannot charge or operate.

≥Check that the iPhone/iPad/iPod is connected properly. (l 6)

≥Connect the iPhone/iPad/iPod again or try to restart the iPhone/ iPad/iPod.

≥During standby mode, charging will not start from the USB cable connection.

Turn this unit on and make sure the charging has started before turning this unit to standby mode.

≥The battery of the iPhone/iPad/iPod is depleted. Charge the iPhone/iPad/iPod, and then operate again.

–When using the port, turn this unit on. Do not turn this unit off until the iPhone/iPad/iPod becomes operational.

Bluetooth®

Pairing cannot be completed.

≥ Check the Bluetooth® device condition.

The device cannot be connected.

≥The pairing of the device was unsuccessful or the registration has been replaced. Try re-pairing the device. (l 7)

≥This unit might be connected to a different device. Disconnect the other device and try re-pairing the device. (l 7)

The device is connected, but audio cannot be heard through this unit.

≥For some built-in Bluetooth® devices, you have to set the audio output to “SC-HC49” manually. Read the operating instructions for the device for details.

The sound is interrupted.

≥The device is out of the 10 m communication range. Place the Bluetooth® device closer to this unit.

≥Remove any interference between this unit and the device.

≥Other devices that use the 2.4 GHz frequency band, such as wireless routers, microwaves, cordless phones, etc. are interfering. Place the Bluetooth® device closer to this unit and distance it from the other devices.

≥Select “MODE 1” for stable communication. (l 8)

The One-Touch Connection (NFC feature) is not working.

≥Make sure the unit and the NFC feature of the device are turned on. (l 7)

Messages

The following messages or service numbers may appear on the unit’s display.

“--:--”

≥You plugged the AC mains lead in for the first time or there was a power failure recently. Set the time (l 11).

“ADJUST CLOCK”

≥ Clock is not set. Adjust the clock accordingly.

“ADJUST TIMER”

≥ Play timer is not set. Adjust the play timer accordingly.

“AUTO OFF”

≥The unit has been left unused for about 20 minutes and will shut down within a minute. Press any button to cancel it.

“CHECKING CONNECTION”

≥The unit is checking the connected iPhone/iPad/iPod.

≥If this display keeps appearing, make sure that the battery of the iPhone/iPad/iPod is not depleted and that the iPhone/iPad/iPod is turned on and connected correctly (l 6).

14

RQT9886

“ERROR”

≥Incorrect operation is performed. Read the instructions and try again.

“F ” (“ ” stands for a number.)

≥There is a problem with this unit.

Write down the displayed number, disconnect the AC mains lead and consult your dealer.

“ILLEGAL OPEN”

≥Sliding door is in the wrong position. Turn the unit off and on again. If this display appears again, consult the dealer.

“IPOD_DOCK OVER CURRENT ERROR” “USB OVER CURRENT ERROR”

≥The iPhone/iPad/iPod is drawing too much power. Disconnect the iPhone/iPad/iPod and turn the unit off and on again.

≥The USB device is drawing too much power. Select a source other than “USB”, remove the USB and turn the unit off.

“NODEVICE”

≥The iPhone/iPad/iPod or USB device is not inserted correctly. Read the instructions and try again (l 6).

≥The battery of the iPhone/iPad/iPod is depleted. Charge the iPhone/iPad/iPod and turn it on before connecting.

“NO DISC”

≥ Insert the disc to be played (l 6).

“NO PLAY”

≥A CD that is not in CD-DA or MP3 format is inserted. It cannot be played.

≥Examine the content. You can only play supported format. (l 16)

≥The files in the USB device can be corrupted. Format the USB device and try again.

≥The unit may have a problem. Turn the unit off and then on again.

“NOT SUPPORTED”

≥You have connected an iPhone/iPad/iPod that cannot be played (l 16).

≥If the iPhone/iPad/iPod is compatible, turn it on and connect it correctly.

“PLAYERROR”

≥You played an unsupported MP3 file. The system will skip that track and play the next one.

“READING”

≥The unit is checking the CD information. After this display has disappeared, start operating.

“REMOTE ” (“ ” stands for a number.)

≥The remote control and this unit are using different codes. Change the code on the remote control.

–When “REMOTE 1” is displayed, press and hold [OK] and [ ] for at least 4 seconds.

–When “REMOTE 2” is displayed, press and hold [OK] and [CD/ RADIO] for at least 4 seconds.

“VBR”

≥The system cannot show the remaining play time for variable bit rate (VBR) tracks.

Unit and media care

Pull out the AC mains lead from the outlet before maintenance.

∫ Clean this unit with a soft, dry cloth

	≥ When dirt is heavy, wring a wet cloth tightly to wipe the dirt,
	and then wipe it with a dry cloth.
	≥ When cleaning the speaker covers, use a fine cloth.
	Do not use tissues or other materials that can fall apart.
	Small pieces may get stuck inside the speaker cover.
	≥ Never use alcohol, paint thinner or benzine to clean this unit.	ENGLISH
	≥ Before using chemically treated cloth, carefully read the
	cloth’s instructions.

∫ Maintenance of the lens

≥ Clean the lens regularly to prevent malfunctions. Use a dust blower to remove dust and a cotton swab if it is extremely dirty.

≥ You cannot use a CD type lens cleaner.

≥ Do not leave the sliding door open for prolonged periods of time. This will cause the lens to get dirty.

≥ Be careful not to touch the lens with your fingers.

	Lens
∫ Clean discs
DO	DO NOT

Wipe with a damp cloth and then wipe dry.

∫ Disc handling precautions

≥Handle discs by the edges to avoid inadvertent scratches or fingerprints on the disc.

≥Do not attach labels or stickers to discs.

≥Do not use record cleaning sprays, benzine, thinner, static electricity prevention liquids or any other solvent.

≥Do not use the following discs:

–Discs with exposed adhesive from removed stickers or labels (rented discs etc.).

–Discs that are badly warped or cracked.

–Irregularly shaped discs, such as heart shapes.

∫ To dispose or transfer this unit

The unit may keep the user settings information in the unit. If you discard this unit either by disposal or transfer, then follow the procedure to return all the settings to the factory defaults to delete the user settings.

(l 13, “To return all settings to the factory defaults”)

≥The operation history may be recorded in the memory of this unit.

15

RQT9886

About Bluetooth®

Playable media

Panasonic bears no responsibility for data and/or information that is compromised during a wireless transmission.

∫ Frequency band used

≥ This system uses the 2.4 GHz frequency band.

∫ Certification of this device

≥This system conforms to frequency restrictions and has received certification based on frequency laws. Thus, a wireless permit is not necessary.

≥The actions below are punishable by law in some countries:

–Taking apart or modifying the system.

–Removing specification indications.

∫ Restrictions of use

≥Wireless transmission and/or usage with all Bluetooth® equipped devices is not guaranteed.

≥All devices must conform to standards set by Bluetooth SIG, Inc.

≥Depending on the specifications and settings of a device, it can fail to connect or some operations can be different.

≥This system supports Bluetooth® security features. But depending on the operating environment and/or settings, this security is possibly not sufficient. Transmit data wirelessly to this system with caution.

≥This system cannot transmit data to a Bluetooth® device.

∫ Range of use

≥Use this device at a maximum range of 10 m. The range can decrease depending on the environment, obstacles or interference.

∫ Interference from other devices

≥This system may not function properly and troubles such as noise and sound jumps may arise due to radio wave interference if this system is located too close to other Bluetooth® devices or the devices that use the 2.4 GHz band.

≥This system may not function properly if radio waves from a nearby broadcasting station, etc. is too strong.

∫ Intended usage

≥This system is for normal, general use only.

≥Do not use this system near an equipment or in an environment that is sensitive to radio frequency interference (example: airports, hospitals, laboratories, etc).

Compatible iPhone/iPad/iPod

Compatible with the dock (Using Lightning connector)

iPhone 5s / iPhone 5c / iPhone 5

iPod touch (5th generation)

iPod nano (7th generation)

Compatible with the port

[Using dedicated USB cable (not supplied)]

iPhone 5s / iPhone 5c / iPhone 5 / iPhone 4S / iPhone 4 / iPhone 3GS / iPhone 3G / iPhone

iPad mini with Retina display / iPad Air / iPad (3rd, and 4th generation) / iPad 2 / iPad / iPad mini

iPod touch

1st, 2nd, 3rd, 4th, and 5th generation

iPod nano

2nd, 3rd, 4th, 5th, 6th, and 7th generation

(as of December 2013)

≥Compatibility depends on the software version. Update your iPhone/iPad/iPod to the latest software before using it with this unit.

≥Please be aware that Panasonic accepts no responsibility for the loss of data and/or information.

≥Do not connect the following models to the port:

–iPod classic, iPod [4th (colour display), and 5th (video) generation], iPod nano (1st generation)

Unexpected behaviour may occur.

Compatible CD

≥A disc with the CD Logo.

≥This unit can play back discs that conform to the CD-DA format.

≥The unit may not be able to play some discs due to the condition of the recording.

≥Before playback, finalise the disc on the device it was recorded on.

Compatible USB devices

≥This unit does not guarantee connection with all USB devices.

≥FAT12, FAT16 and FAT32 file systems are supported.

≥This unit supports USB 2.0 full speed.

≥This unit can support USB devices of up to 32 GB.

16

RQT9886

Compatible MP3 files

≥Supported format: Files with the extension “.mp3” or “.MP3”.

≥Compatible compression rate: Between 16 kbps and 320 kbps (stereo).

≥Depending on how you create the MP3 files, they may not play in the order you numbered them or may not play at all.

CD-R/RW

≥Maximum number of tracks and albums: 999 tracks and 254 albums (Excluding Root folder).

≥Disc formats: ISO9660 level 1 and level 2 (except for extended formats).

≥If the disc includes both MP3 and normal audio data (CD-DA), the unit plays the type recorded in the inner part of the disc.

≥This unit cannot play files recorded using packet write.

USB device

≥Maximum number of tracks and albums: 8000 tracks and 799 albums (Excluding Root folder).

≥Only one memory card will be selected when connecting a multiport USB card reader, typically the first memory card inserted.

Licenses

“Made for iPod”, “Made for iPhone”, and “Made for iPad” mean that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance.

iPad, iPhone, iPod, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Lightning is a trademark of Apple Inc.

The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Panasonic Corporation is under license.

Other trademarks and trade names are those of their respective owners.

Google Play and Android are trademarks of Google Inc.

MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.

ENGLISH

17

RQT9886

Attaching the unit to a wall (optional)

This unit can be wall mounted using the supplied wall mount brackets, etc. Make sure that the wall and the screws used for securing to the wall are capable of supporting at least 33 kg. The screws and other items are not supplied as the type and size will vary with each installation.

≥Refer to step 5 of “Wall mount instructions” for details about the required screws.

≥As an additional protective measure, attach the unit to the wall with the fall prevention cord.

Installation accessories

∫ Supplied accessories

≥1 Safety holder

≥1 Screw

≥2 Wall mount brackets

∫ Additionally required accessories

(commercially available)

≥4 Wall mount bracket fixing screws

≥1 Safety holder fixing screw

≥1 Fall prevention cord*

≥1 Screw eye

*Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm).

≥Keep the safety holder out of reach of children to prevent swallowing.

≥Keep the screws out of reach of children to prevent swallowing.

≥Keep the wall mount brackets out of reach of children to prevent swallowing.

Safety precautions

Professional installation is required.

The installation should never be done by any other than a qualified installation specialist. PANASONIC DISCLAIMS ANY PROPERTY DAMAGE AND/OR SERIOUS INJURY, INCLUDING DEATH RESULTING FROM IMPROPER INSTALLATION OR INCORRECT HANDLING.

WARNING:

To prevent injury, this apparatus must be securely attached to the wall in accordance with the installation instructions.

Wall mount instructions

Before installation, turn the unit off and disconnect the AC mains lead from the mains socket.

1 Detach the stand from the unit.

≥Unscrew the fixing screw at the bottom of the unit.

≥Gently pull the stand off the unit as illustrated.

≥Keep the removed screw and the stand in a safe place.

Stand

Fixing screw

Soft blanket or cloth

2 Fix the safety holder onto the unit with the screw (supplied).

≥ Screw tightening torque: 50 N0cm to 70 N0cm.

Screw

(supplied)

3 Attach the fall prevention cord (not supplied) to this unit.

Cord

(not supplied)

18

RQT9886

4 Measure and mark the position of both sides of the wall mount brackets.

≥ Use figures below to identify the screwing positions.

The position to attach the wall mount brackets

13 mm

204 mm

Space required

142 mm	300 mm
	154 mm

75 mm

142 mm

100 mm

500 mm

100 mm

5 Attach the wall mount bracket to both sides of the wall with two screws (not supplied).

≥Use a level to ensure both wall mount brackets are level.

At least 30 mm

‰7.5 mm to ‰9.4 mm

Wall mount bracket

‰4 mm

6 Hook the unit securely onto the wall mount brackets with both hands.

≥Connect the antenna and the AC mains lead to the unit before hanging the unit onto the wall. (l 5)

≥After hanging the unit, release your hands carefully to confirm the unit sits securely on the wall mount brackets.

Wall	ENGLISH

7 Drive the safety holder fixing screw (not supplied) to secure the safety holder onto the wall.

≥ Refer to step 5 for requirements before screwing.

Fix to the wall

Safety holder

Safety holder fixing screw (not supplied)

8 Attach the fall prevention cord (not supplied) to the wall.

≥ Make sure that the slack of the cord is minimal.

Screw eye (not supplied)

Cord (not supplied)

Wall

19

RQT9886

Specifications

∫ GENERAL

Power consumption	37 W
Power consumption in standby mode*1, 2
	Approx. 0.2 W
(When “BLUETOOTH STANDBY” is “ON”)*2
	Approx. 0.3 W
Power supply	AC 220 V to 240 V, 50 Hz
Dimensions (WkHkD)	500 mmk205 mmk92 mm
Mass	Approx. 2.5 kg

Operating temperature range

0 oC to r40 oC

Operating humidity range

35 % to 80 % RH (no condensation)

∫ AMPLIFIER SECTION

Output power

RMS Output Power Stereo mode Front Ch (both ch driven)

20 W per channel (8 ≠), 1 kHz, 10 % THD

Total RMS Stereo mode power

	40 W
∫ TUNER SECTION
Preset Memory	FM 30 stations
Frequency Modulation (FM)
Frequency range

87.50 MHz to 108.00 MHz (50 kHz step)

Antenna terminals

75 ≠ (unbalanced)

∫ DISC SECTION

Disc played (8 cm or 12 cm)

Pick up	CD, CD-R/RW (CD-DA, MP3*3)
Wavelength	790 nm (CD)
[NORSK]
Bølgelengde	790 nm (CD)
Laserstyrke	Ingen farlig stråling sendes ut
	(med sikkerhets-beskyttelse)

∫ SPEAKER SYSTEM SECTION

	Speaker unit(s)
	Full range	6.5 cm Cone typek1 per channel
	Passive Radiator
		8 cmk2 per channel
	Impedance	8 ≠

∫ TERMINAL SECTION

Dock connection

DC OUT 5 V 1.0 A

Port connection

DC OUT 5 V 2.1 A

USB Standard

USB 2.0 full speed

Media file format support

MP3 (¢.mp3)

USB device file system

FAT12, FAT16, FAT32

∫ BLUETOOTH SECTION

	Version	Bluetooth® Ver.2.1+EDR
	Class	Class 2
	Supported Profiles	A2DP, AVRCP
	Operating Frequency
		2.4 GHz band FH-SS
	Operation Distance
		10 m Line of sight

≥Specifications are subject to change without notice.

≥Mass and dimensions are approximate.

≥Total harmonic distortion is measured by a digital spectrum analyzer.

*1: “BLUETOOTH STANDBY” is “OFF”.

*2: No device is connected to the port or the dock before turning to standby mode.

*3: MPEG-1 Layer 3, MPEG-2 Layer 3

20

RQT9886

Attaching the support pad to this unit

Attach the supplied support pad to prevent damage or scratches to this unit or the device connected to the dock. Attach the pad before using the dock.

≥ The location is the same for either iPhone, iPod touch, or iPod nano.

1 Align this page to the sliding door and locate the position to attach the pad.

ENGLISH

A Align with the top of unit.

B Align with the side of the sliding door. C Pad (supplied)

2 Attach the pad near the corner of this page. e.g., iPhone 5

DThere will be a gap between the unit and the connected device.

≥2 pads are supplied with this unit.

Keep the other pad in a secure place for future use.

21

RQT9886

Zasady bezpieczeństwa

OSTRZEËENIE

Urządzenie

≥Aby ograniczyć niebezpieczeństwo pożaru, porażenia prądem lub uszkodzenia urządzenia,

–Nie należy wystawiać urządzenia na działanie deszczu, wilgoci, kapanie lub zachlapanie.

–Na urządzeniu nie należy ustawiać żadnych naczyń zawierających płyny, takich jak wazony.

–Należy korzystać wyłącznie z zalecanych akcesoriów.

–Nie należy demontować obudowy urządzenia.

–Nie należy podejmować prób samodzielnej naprawy. Naprawę urządzenia należy zlecić wykwalifikowanym pracownikom serwisu.

–Należy uważać, aby do wnętrza urządzenia nie dostały się metalowe przedmioty.

–Na urządzeniu nie wolno umieszczać żadnych ciężkich przedmiotów.

Przewód zasilania

≥Aby ograniczyć niebezpieczeństwo pożaru, porażenia prądem lub uszkodzenia urządzenia,

–Należy się upewnić, że napięcie źródła zasilania odpowiada napięciu podanemu na urządzeniu.

–Dokładnie podłączyć wtyczkę przewodu zasilającego do gniazda ściennego.

–Nie wolno ciągnąć za przewód, zginać go ani kłaść na nim ciężkich przedmiotów.

–Nie wolno dotykać wtyczki mokrymi rękami.

–Przy odłączaniu przewodu należy chwycić za wtyczkę.

–Nie wolno podłączać urządzenia do uszkodzonego gniazda ściennego oraz gdy wtyczka przewodu zasilającego jest uszkodzona.

≥Wtyczka zasilania umożliwia odłączenie urządzenia. Zainstaluj to urządzenie w taki sposób, aby możliwe było natychmiastowe odłączenie wtyczki zasilania od gniazda zasilania.

UWAGA

Urządzenie

≥W tym urządzeniu znajduje się laser. Wykonywanie regulacji innych niż opisane lub postępowanie w sposób nieprzewidziany w instrukcji obsługi grozi niebezpiecznym naświetleniem promieniami lasera.

≥Nie należy umieszczać na urządzeniu źródeł otwartego ognia, takich jak zapalone świece.

≥To urządzenie może odbierać zakłócenia wywołane użyciem telefonu komórkowego. Jeżeli takie zakłócenia wystąpią, wskazane jest zwiększenie odległości pomiędzy urządzeniem a telefonem komórkowym.

≥Urządzenie jest przeznaczone do używania w klimacie umiarkowanym.

Wybór miejsca

≥Urządzenie należy ustawić na równej powierzchni.

≥Aby ograniczyć niebezpieczeństwo pożaru, porażenia prądem lub uszkodzenia urządzenia,

–Niniejszego urządzenia nie należy instalować lub umieszczać w szafce na książki, zabudowanej szafce lub innej ograniczonej przestrzeni, w celu zapewnienia dobrej wentylacji.

–Nie należy zasłaniać otworów wentylacyjnych urządzenia gazetami, obrusami, zasłonami i podobnymi przedmiotami.

–Urządzenie należy chronić przed bezpośrednim działaniem promieni słonecznych, wysoką temperaturą, wysoką wilgotnością oraz nadmiernymi drganiami.

Bateria

≥Istnieje niebezpieczeństwo wybuchu w przypadku, gdy baterie zostaną nieprawidłowo włożone. Baterie należy wymieniać wyłącznie na baterie typu zalecanego przez producenta.

≥Nieprawidłowe obchodzenie się z bateriami może prowadzić do wycieku elektrolitu i może być także przyczyną pożaru.

–Baterię należy wyjąć, jeżeli pilot nie będzie używany przez dłuższy czas. Należy ją przechowywać w chłodnym, ciemnym miejscu.

–Nie ogrzewaj i nie wrzucaj do ognia.

–Nie należy pozostawiać baterii przez dłuższy czas w samochodzie z zamkniętymi drzwiami i oknami wystawionym na bezpośrednie działanie promieni słonecznych.

–Nie demontuj i nie powoduj zwarcia.

–Baterii alkalicznych lub manganowych nie należy ładować ponownie.

–Nie używaj baterii, z których usunięta została osłona.

≥W przypadku utylizacji baterii, należy się skontaktować z lokalnymi władzami lub ze sprzedawcą celem uzyskania informacji o prawidłowym sposobie postępowania.

Oznaczenia identyfikacyjne produktu znajdują się na spodzie urządzenia.

Deklaracja zgodności

Niniejszym “Panasonic Corporation” deklaruje, że ten produkt jest zgodny z istotnymi wymaganiami i innymi odnośnymi postanowieniami dyrektywy 1999/5/WE.

Klienci mogą pobrać oryginalną deklarację zgodności naszych produktów z serwera deklaracji zgodności: http://www.doc.panasonic.de

Kontakt się z autoryzowanym przedstawicielem: Panasonic Marketing Europe GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg, Niemcy

Ten produkt jest przeznaczony dla użytkownika ogólnego. (Kategoria 3)

22

RQT9886

Spis treści
Zasady bezpieczeństwa .................................	22
Akcesoria.........................................................	23
Instrukcja sterowania .....................................	24
Podłączenia .....................................................	25
Wsadzanie nośników......................................	26
Operacje Bluetooth® .......................................	27
Przyciski odtwarzania z nośników ................	29
Słuchanie radia ...............................................	30
Regulacja dźwięku..........................................	31
Zegar i timer ....................................................	31
Inne ..................................................................	32
Usuwanie usterek ...........................................	33
Konserwacja urządzenia i nośników ............	35
Informacje o Bluetooth® .................................	36
Nośniki, które mogą być odtwarzane ...........	36
Licencje ...........................................................	37
Mocowanie urządzenia do ściany
(opcjonalne) ....................................................	38
Dane techniczne .............................................	40
Przymocowywanie podkładki
podpierającej do tego urządzenia .................	41

Informacje dotyczące opisów w niniejszej instrukcji obsługi

≥Odniesienia do stron są oznaczone jako “l ±±”.

≥Jeżeli brak innych instrukcji, wykonywanie operacji opisano z użyciem zdalnego sterowania.

Akcesoria

Sprawdź dostarczone akcesoria przed rozpoczęciem użytkowania urządzenia..

∏1 Pilot zdalnego sterowania

(N2QAYB000945)

∏1 Bateria do pilota zdalnego sterowania

∏1 Kabel zasilania prądem przemiennym

∏ 1 Antena

wewnętrzna FM

∏ 1 arkusz podkładki

(podkładka podpierająca)

Akcesoria do montażu ściennego

∏	1 Uchwyt	∏ 2 Wsporniki
	bezpieczeństwa	ścienne
		POLSKI
∏	1 Śruba

≥Nie używaj kabla zasilającego do zasilania innych produktów.

≥Numery produktów podane w niniejszej instrukcji obsługi według stanu na grudzień 2013. Mogą ulec zmianie.

Pozbywanie się zużytych urządzeń elektrycznych i elektronicznych oraz baterii.

Dotyczy wyłącznie obszaru Unii Europejskiej oraz krajów posiadających systemy zbiórki i recyklingu.

Niniejsze symbole umieszczane na produktach, opakowaniach i/lub w dokumentacji

towarzyszącej oznaczają, że nie wolno mieszać zużytych urządzeń elektrycznych i

elektronicznych oraz baterii z innymi odpadami domowymi/komunalnymi.

W celu zapewnienia właściwego przetwarzania, utylizacji oraz recyklingu zużytych urządzeń elektrycznych i elektronicznych oraz zużytych baterii, należy oddawać je do wyznaczonych

punktów gromadzenia odpadów zgodnie z przepisami prawa krajowego.

Poprzez prawidłowe pozbywanie się zużytych urządzeń elektrycznych i elektronicznych oraz zużytych baterii pomagasz oszczędzać cenne zasoby naturalne oraz zapobiegać potencjalnemu negatywnemu wpływowi na zdrowie człowieka oraz na stan środowiska naturalnego.

W celu uzyskania informacji o zbiórce oraz recyklingu zużytych urządzeń elektrycznych i elektronicznych oraz baterii prosimy o kontakt z władzami lokalnymi.

Za niewłaściwe pozbywanie się tych odpadów mogą grozić kary przewidziane przepisami prawa krajowego.

Dotyczy symbolu baterii (symbol poniżej):

Ten symbol może występować wraz z symbolem pierwiastka chemicznego. W takim przypadku wymagania Dyrektywy w sprawie określonego środka chemicznego są spełnione.

23

RQT9886

Instrukcja sterowania

1

Przełącznik trybu gotowości/włączania (Í/I)

Widok z góry

(Í)

Naciśnij, aby przełączyć urządzenie z trybu włączenia na

tryb gotowości lub odwrotnie.

W trybie gotowości urządzenie wciąż zużywa niewielką

2

ilość energii.

Wybór źródła dźwięku

Na urządzeniu:

“CD” ------------. “BLUETOOTH” ------------. “IPOD_DOCK”

^"""--"" “FM” ,"""--"" “USB”* ,"""--"}

Na pilocie:

[ ]: “BLUETOOTH”

[iPod/USB]: “IPOD_DOCK” ,. “USB”*

3

[CD/RADIO]: “CD” ,. “FM”

Podstawowe przyciski sterowania odtwarzaniem

4

Regulacja poziomu głośności (0 (min.) do 50

5

(maks.))

Otwórz lub zasuń odsuwaną pokrywę

6

Bluetooth®-przycisk parowania

≥ Naciśnij, aby wybrać “BLUETOOTH” jako źródło

dźwięku.

≥ Naciśnij i przytrzymaj, aby wejść do trybu parowania

(l 27) lub rozłączyć urządzenie Bluetooth® (l 28).

7

Obszar kontaktu NFC (l 27)

8

Port urządzeń iPhone/iPad/iPod i urządzeń USB

(l 26)

9

Wybierz “USB”* jako źródło dźwięku.

Czujnik sygnału zdalnego sterowania

Odległość: Do około 7 m bezpośrednio na wprost Kąt około 30o w lewo i prawo

10 Wyświetlacz

11 Odsuwana pokrywa

12 Stacja dokująca dla urządzenia iPhone/iPod

Wybierz “IPOD_DOCK” jako źródło dźwięku.

13 Wyświetlanie menu ustawień

14 Wyświetlanie menu iPhone/iPod / Zmiana wyświetlanych informacji

15 Wyświetlanie menu dźwięku

16 Przyciemnianie panelu wyświetlacza

Naciśnij ponownie, aby anulować.

17 Wyciszanie dźwięku

Naciśnij ponownie, aby anulować. “MUTE” jest także anulowana podczas regulacji głośności i po wyłączeniu urządzenia.

18 Wyświetlanie menu odtwarzania

19 Wybór/OK

* Informacja na wyświetlaczu automatycznie zmieni się na “IPOD_PORT”, kiedy kompatybilne urządzenie iPhone/ iPad/iPod jest podłączone do portu iPhone/iPad/iPod.

∫ Korzystanie z pilota

Włóż baterię tak, aby bieguny (i oraz j) odpowiadały biegunom w pilocie.

Skieruj na czujnik odbioru sygnału pilota w urządzeniu.

≥ Aby uniknąć zakłóceń, nie umieszczaj żadnych przedmiotów przed czujnikiem sygnału.

24	(Bateria alkaliczna lub
	manganowa)

RQT9886

Podłączenia

1Podłącz antenę.

Taśma klejąca (brak w zestawie)

Antena wewnętrzna FM (w zestawie)

2Podłącza kabel zasilacza sieciowego dopiero po ustanowieniu wszystkich innych połączeń.

Urządzenie pobiera niewielką ilość energii elektrycznej (l 40) nawet po wyłączeniu.

≥W celu oszczędzania energii elektrycznej

odłącz urządzenie od gniazdka, gdy nie będzie używane przez dłuższy czas.

Do gniazdka elektrycznego

Kabel zasilania prądem przemiennym (w zestawie)

≥Głośniki nie są ekranowane magnetycznie. Nie umieszczaj ich w pobliżu telewizora, komputera osobistego ani innych urządzeń emitujących pole magnetyczne.

≥Przymocuj taśmą antenę do ściany lub do kolumny w pozycji zapewniającej najmniejsze zakłócenia.

≥Jeżeli odbiór sygnałów radiowych jest słaby, użyj zewnętrznej anteny FM z kątowym złączem antenowym (brak w zestawie).

POLSKI

25

RQT9886

Wsadzanie nośników

∫ Podłączanie urządzenia iPhone/iPad/iPod* lub urządzenia USB

Po podłączeniu kompatybilnego urządzenia do portu lub stacji dokującej w trybie “USB” lub “IPOD_DOCK”, przełącznik automatycznie wybierze odpowiednie źródło dla urządzenia.

Naciśnij [iPod/USB], aby wybrać “USB”.

Informacja na wyświetlaczu automatycznie zmienia się na “IPOD_PORT”, kiedy kompatybilne urządzenie iPhone/iPad/iPod jest podłączone do portu.

≥ Podczas podłączania iPhone/iPad/iPod używaj odpowiedniego kabla USB (brak w zestawie).

≥ Włóż urządzenie USB bezpośrednio do gniazda USB. Nie używaj kabla przedłużającego USB.

≥ Po zakończeniu używania urządzenia USB należy je odłączyć. ≥ Przed wyjęciem urządzenia USB wybierz źródło inne niż “USB”.

∫ Wkładanie płyty CD

Strona z

etykietą

≥ Przechyl płytę, aby nie dotykała odsuwanej pokrywy. ≥ Nie otwierać ręcznie przesuwanej pokrywy.

podkładka (w zestawie)

≥ Zanim skorzystasz ze stacji dokującej, przymocuj podkładkę. (l 41)

∫ Podłączanie urządzenia iPhone/iPod* za pomocą złącza Lightning

Po podłączeniu kompatybilnego urządzenia do portu lub stacji dokującej w trybie “USB” lub “IPOD_DOCK”, przełącznik automatycznie wybierze odpowiednie źródło dla urządzenia.

Naciśnij [iPod/USB], aby wybrać “IPOD_DOCK”.

Aby zamknąć stację dokującą

Naciśnij i przytrzymaj [PUSH CLOSE] podczas zamykania stacji dokującej.

Złącze

Lightning

≥Pamiętaj o wyjęciu urządzenia iPhone/iPod z futerału.

≥Upewnij się, że iPhone/iPod jest wsadzony do końca i że jego tylna część oparta jest o podkładkę.

≥Przytrzymaj stację dokującą podczas wyjmowania iPhone/iPod.

*Przeczytaj “Nośniki, które mogą być odtwarzane”, aby dowiedzieć się więcej o kompatybilnych modelach. (l 36)

∫ Ładowanie iPhone/iPad/iPod

Kiedy urządzenie jest włączone, ładowanie rozpocznie się po podłączeniu iPhone/iPad/iPod do głównego urządzenia.

≥ Aby kontynuować ładowanie za pomocą kabla USB w trybie gotowości, upewnij się, że ładowanie iPhone/iPad/iPod zostało rozpoczęte przed przełączeniem urządzenia w tryb gotowości.

≥ Kiedy urządzenie pracuje w trybie gotowości, ładowanie rozpocznie się standardowo za pomocą złącza Lightning. ≥ Sprawdź, czy akumulator urządzenia iPhone/iPad/iPod został w pełni naładowany. (Gdy urządzenie zostanie w pełni

naładowane, usuń iPhone/iPad/iPod.)

≥ Wkładając lub wyjmując nośnik, upewnij się, że urządzenie nie spadnie.

26 ≥ Przed przeniesieniem urządzenia wyjmij wszystkie nośniki i przełącz urządzenie w tryb gotowości.

RQT9886