Panasonic PV-L552 User Manual

Camcorder

Operating Instructions

Getting Started

Model No.

PV-L552

Basic Operation

Special Features

For Your Information

Please read these instructions carefully before attempting to operate this product. Please save this manual.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

LSQT0557A

Things You Should Know

Thank you for choosing Panasonic!

You have purchased one of the most sophisticated and reliable products on the market today. Used properly, it will bring you years of enjoyment. Please take time to fill in the information to the right. The serial number is on the tag located on the rear side of your Camcorder. Be sure to retain this manual as your convenient Camcorder information source.

Date of Purchase

Dealer Purchased From

Dealer Address

Dealer Phone No.

Model No.

Serial No.

Unpack your Camcorder

These accessories are provided in order to set up or use your Camcorder.

1 pc. AC Adaptor (PV-A19/PV-A20) with DC Power Cable (page 10)

1 pc. Shoulder Strap (LSFC0012) (page 12)

1 pc. Audio/Video Cable (LSJA0390) (pages 21, 22)

1 pc. CR2025 Clock Battery (VSBW0004) (installed in Camcorder) (page 34)

1 pc. Battery Pack (PV-BP18) (pages 9, 10)

1 pc. VHS PlayPak (PV-P1/VYMW0009) and one “AA” battery (page 21)

1 pc. Lens Cap (LSYK0817) with Lens Cap Strap (LSGQ0049) (page 12)

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Things You Should Know

Safety Precautions

WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

Your Compact VHS Camcorder is designed to record and play back in Standard Play (SP) and Super Long Play (SLP) modes. You can also play a Compact VHS Camcorder recording on your VHS VCR using the supplied VHS PlayPak.

This Camcorder is equipped with the HQ System to provide excellent video pictures, and is compatible with standard VHS equipment. It is recommended that only cassette tapes that have been tested and inspected for use in VCR machines with the

The above markings are located on the appliance’s bottom cover.

FCC Warning: Any unauthorized changes or modifications to this equipment would

void the user’s authority to operate.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with Part 15 and part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a residential environment. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced radio/TV technician for help. You may find the booklet, ‘Something About Interference’ available from FCC local regional offices helpful.

This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communication equipment operating between 0.45-30 MHz.

and/or mark be used.

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

Getting Started

Important Safeguards

1. Read Instructions – All the safety and

operating instructions should be read before the unit is operated.

2. Retain Instructions – The safety and

operating instructions should be retained for future reference.

3. Heed Warnings – All warnings on the unit

and in the operating instructions should be adhered to.

4. Follow Instructions – All operating and

maintenance instructions should be followed.

5. Cleaning – Unplug this video unit from the

wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a dry cloth for cleaning.

6. Attachments – Do not use attachments not

recommended by the video product manufacturer as they may be hazardous.

7. Water and Moisture – Do not use this video unit near water – for example near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

8. Accessories – Do not place this video unit on an unstable cart, stand, tripod, bracket, or table. The video unit may fall, causing serious injury to a child or adult, and serious damage to the unit. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the video unit. Any mounting of the unit should follow the manufacturer’s instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

9. Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the video unit and to protect it from overheating. These openings must not be blocked or covered. Never place the video unit on a bed, sofa, rug, or other similar surface, or near or over a radiator or heat register. This video unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

10. Power Sources – This video unit should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For video units intended to be operated from battery power, or other sources, refer to the operating instructions.

11. Grounding or Polarization – This video unit

may be equipped with either a polarized 2-wire AC (Alternating Current) line plug (a plug having one blade wider than the other) or 3-wire grounding type plug, a plug having a third (grounding) pin.

The 2-wire polarized plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still fails to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

The 3-wire grounding type plug will fit into a grounding type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding type plug.

12. Power-Cord Protection – Power-supply

cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Paying particular attention to cords of plugs, convenience receptacles, and the point where they exit from the unit.

13. Outdoor Antenna Grounding – If an outside

antenna or cable system is connected to the video unit, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Part 1 of the Canadian Electrical Code, in USA Section 810 of the National Electrical Code, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

14. Lightning – For added protection of this

video unit receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video unit due to lightning and power-line surges.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Important Safeguards

15. Power Lines – An outside antenna system

should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16. Overloading – Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

17. Objects and Liquids – Never push objects of any kind into this video unit through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind onto the video unit.

18. Servicing – Do not attempt to service this video unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19. Damage Requiring Service – Unplug this video unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power-supply cord or plug is

damaged.

b. If any liquid has been spilled into, or

objects have fallen onto, the video unit.

c. If the video unit has been exposed to rain

or water.

d. If the video unit does not operate normally

by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video unit to its normal operation.

e. If the video unit has been dropped or the

cabinet has been damaged.

f. When the video unit exhibits a distinct

change in performance – this indicates a need for service.

20. Replacement Parts – When replacement

parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

21. Safety Check – Upon completion of any

service or repairs to this video unit, ask the service technician to perform safety checks to determine that the video unit is in safe operating order.

Precautions

Getting Started

USE & LOCATION

• TO AVOID SHOCK HAZARD ... Your Camcorder and power supply should not be exposed to rain or moisture.

Do not connect the power supply or operate your Camcorder if it gets wet. Your Camcorder has been designed for outdoor use, however it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or a direct splashing from a pool or even a cup of coffee. This action could permanently damage the internal parts of your Camcorder. Do not attempt to disassemble this unit. There are no user serviceable parts inside. Unplug your Camcorder from the power supply before cleaning.

• DO NOT AIM YOUR CAMCORDER AT THE SUN OR OTHER BRIGHT OBJECTS.

• DO NOT LEAVE THE CAMCORDER WITH THE EVF AIMED DIRECTLY AT THE SUN AS THIS MAY CAUSE

DAMAGE TO THE INTERNAL PARTS OF THE EVF.

• DO NOT EXPOSE YOUR CAMCORDER TO EXTENDED HIGH TEMPERATURE ... Such as, in direct sunlight,

inside a closed car, next to a heater, etc... This action could permanently damage the internal parts of your Camcorder.

• AVOID SUDDEN CHANGES IN TEMPERATURE ... If the unit is suddenly moved from a cold place to a warm

place, moisture may form on the tape and inside the unit.

• DO NOT LEAVE YOUR CAMCORDER OR THE POWER SUPPLY TURNED ON WHEN NOT IN USE.

• STORAGE OF YOUR CAMCORDER ... Store and handle your Camcorder in a manner that will not subject it to

unnecessary movement (avoid shaking and striking). Your Camcorder contains a sensitive pick-up device which could be damaged by improper handling or storage.

CARE

• TO CLEAN YOUR CAMCORDER ... Do not use strong or abrasive detergents when cleaning your Camcorder

body.

• TO PROTECT THE LENS ... Do not touch the surface of the lens with your hand. Use a commercial camcorder

lens solution and lens paper when cleaning the lens. Improper cleaning can scratch the lens coating.

• TO PROTECT THE FINISH OF YOUR CAMCORDER ... Before handling your Camcorder, make sure your hands

and face are free from any chemical products, such as suntan lotion, as it may damage the finish.

Table of Contents

Getting Started

Things You Should Know ............................................................................. 2~3

Important Safeguards ...................................................................................4~5

Precautions........................................................................................................ 5

Self Demo Mode ................................................................................................ 7

Quick Operation Guide .....................................................................................8

Supplying Power

Cassette Information ...................................................................................... 11

Before Using (Using the Shoulder and Hand Straps, Lens Cap) ............................................ 12

Using MENU Mode .......................................................................................... 13

Setting the Clock (Time Zone, Auto Daylight Saving Time) ....................................... 14~15

Built-in Auto Light (Using the Light, Replacing the Bulb) ............................................... 16

Basic Operation

Camera Recording (Basic, Stand-by, Programmed Recording) .................................... 17~19

Playing Back Recordings

(Basic Playback, Visual Search, Still Picture, Tracking, TV/VCR Playback) ................... 20~21

Copying your Tapes (dubbing) ...................................................................... 22

Special Features

Four-Speed Power Zoom................................................................................ 23

Backlight ..........................................................................................................23

Focus (Auto/Manual Focus) ............................................................................................. 24

High Speed Shutter (Auto/Manual Shutter) .................................................................. 25

Auto Fade......................................................................................................... 26

Color Digital Fade ........................................................................................... 27

Digital Zoom .................................................................................................... 28

Digital Electronic Image Stabilization (E.I.S.) ...............................................29

MotionSensor .................................................................................................. 30

(Battery Charge/Use/Refresh/Care, AC Adaptor, Car Battery Cord) .... 9~10

For Your Information

Viewfinder/LCD Monitor Indications ....................................................... 31~32

Operation Notes (Cleaning EVF) ......................................................................... 33

Notice ............................................................................................................... 33

Replacing Clock Battery .................................................................................34

Palmcorder Accessory System ..................................................................... 35

Palmcorder Accessory Order Form .............................................................. 36

Specifications .................................................................................................. 37

Before Requesting Service (Video Head Cleaning) .............................................. 38

Request for Service Notice ............................................................................ 39

Limited Warranty ............................................................................................. 40

Servicenter List ............................................................................................... 41

Index ................................................................................................................. 42

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Self Demo Mode

Self Demo mode is on when the screen below appears. To turn it off, follow steps 1-4 below.

EVF or LCD Monitor

2, 3, 4

Before you begin...

• Connect Camcorder to power source.

1 Set POWER to CAMERA. 2 Press MENU for

MENU mode.

Press UP or DOWN

to select

SELF DEMO .

3 Press DISPLAY to select OFF. 4 Press MENU to exit.

Note:

• Self Demo stops automatically if battery is attached (page 9) and cassette tape is inserted (page 11).

• Inserting a tape alone (or attaching a partially charged battery) only temporarily stops Self Demo.

• Self Demo stops for 30 seconds when the Light is pressed.

To turn Self Demo back on:

• Set to SELF DEMO : ON in MENU screen.

Getting Started

Quick Operation Guide

Charging the Battery Pack

Charge Battery Pack fully before operation (page 9).

Plug in AC

Adaptor.

Insert Battery. CHARGE Lamp

flashes, then stays lit when charging is complete.

Camera Recording

When the LCD monitor is open, the EVF automatically turns OFF (page 17).

Press LCD-OPEN to unlock the LCD monitor.

Swing it fully open and adjust the angle.

Insert Cassette

Attach fully

charged

(page 9).

Slide TAPE

EJECT to open

door.

Insert cassette

(page 11).

Press here to Protection Film Note:

• Remove the Protection Film before use.

2 3

close door.

Set POWER to CAMERA.

Press RECORD/PAUSE

to start recording.

RECORD/PAUSE

Press

to pause recording.

again

Battery

Playback using the LCD Monitor

When the LCD monitor is open, the EVF automatically turns OFF (page 20).

Press LCD-OPEN to unlock the LCD monitor.

Swing it fully open and adjust the angle (see above).

Set POWER

to VCR.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Press REWIND/SEARCH

to rewind tape.

Press PLAY to start

playback.

Press STOP to stop

playback.

Supplying Power

Charging the Battery Pack

Charge Battery Pack fully before use.

POWER Lamp

1 Plug in AC Adaptor.

POWER Lamp lights.

2 Insert Battery.

A Align left side of Battery with left edge of

AC Adaptor.

B Press Battery down and slide in direction

of arrow.

The CHARGE Lamp flashes, then stays lit when charging is complete.

3 Remove Battery.

Slide Battery to the left and lift off.

CHARGE Lamp

(Top View)

Using the Battery Pack

A fully charged Battery provides a maximum of about 2 hours of continuous use (LCD monitor off) or about 1.5 hours (LCD monitor on). Actual time may vary due to operating conditions. Using the Built-in Light decreases operating time.

Note:

• Charging takes about 1 and 1/2 hours.

• While the DC Power Cable (supplied) is connected

to the AC Adaptor, the Battery cannot be charged.

• After charging 5 times, use Battery Refresh feature as explained below.

• Battery life gradually decreases after repeated use and recharging. If operation time becomes very short even after a sufficient charge, discard Battery properly (page 10).

Getting Started

A B

Battery Refresh

This feature completely discharges Battery before recharging begins. Use after every 5 charges for optimum Battery performance.

REFRESH Lamp

BATTERY REFRESH

Attach Battery.

a Insert top of Battery into top of mounting

surface.

b Press and snap into place.

Remove Battery.

BATTERY RELEASE and remove

Slide Battery.

To use battery refresh, insert Battery on AC Adaptor (see steps 1~2 above), then press BATTERY REFRESH.

The REFRESH Lamp lights, then goes out when discharge is complete. Battery charging will then start automatically.

BATTERY REFRESH is pressed by mistake,

If remove Battery from AC Adaptor and reinsert it for normal charging.

Note:

• Charging takes about 7 and 1/2 hours when Battery Refresh is used.

• Battery will not operate in extremely high temperatures.

Supplying Power

Battery Care

Caution:

• Charge only with specified charger.

• Battery can be charged within a temperature range of

10 °C (50 °F) and 35 °C (95 °F).

• Battery is normally warm after charging or just after use.

• Do not use an insufficiently charged or worn-out Battery.

Safety precautions:

• Do not get Battery near, or dispose of in, fire.

• Do not directly connect (short circuit) the positive (+) and negative (–) terminals.

• Never attempt to disassemble or reassemble Battery.

To avoid Battery damage:

• Do not drop or jar Battery.

• Use Battery with specified units only.

• If Battery is used in extremely high

temperatures, a safety device will automatically prevent operation.

To prolong Battery life:

• While not in use, remove Battery from the Camcorder and AC Adaptor, and store in a cool, dark, dry place.

• Keep Battery terminals clean.

AC Adaptor

1 Connect AC Adaptor DC OUT to

DC Power Cable

Camcorder DC IN with supplied DC

Power Cable.

2 Plug in AC Adaptor.

POWER Lamp

DC IN Connector

DC OUT Connector

CAUTION:

This unit will operate on 110/120/220/240 V AC 50/60 Hz. An AC plug adaptor may be required for voltages other than 120 V AC. Please contact either a local or foreign electrical parts distributor for assistance in selecting an alternate AC plug. We recommend using the accessory power plug adaptor (VJSS0070) in an area which has special AC outlets.

POWER Lamp lights.

Note:

• While the DC Power Cable (supplied) is connected to the AC Adaptor, the Battery cannot be charged.

• When not in use, unplug AC Adaptor from AC outlet. (Adaptor uses 1.2 W of electricity while plugged in.)

Car Battery Cord (Optional)

1 Connect PV-C16 Car Battery Cord

(optional) to Camcorder DC IN.

2 A Start engine first.

B Plug Car Battery Cord into

Cigarette lighter socket.

Cigarette Lighter Socket (12 V)

DC IN Connector

Car Battery Cord (optional)

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Cigarette Lighter Plug

• If Car Battery cord fuse needs replacing, use exact current rating (in amps).

Note:

• This cord only works in vehicles equipped

with DC 12 V (negative ground) battery. Check with your car/truck dealer. Use only specified car battery cord.

• To avoid blowing the car battery cord fuse, do step 2 in the proper order.

• Running vehicles must be well ventilated.

• When not in use, disconnect cigarette

lighter plug.

• For personal safety the driver of the vehicle should not attempt to operate the camcorder while driving.

Cassette Information

Cassette Insertion/Removal

1 3

Record/Playback Time

Use tapes with the mark in this unit.

Tape Speed Selector Position

(Standard Play)

SLP

(Super Long Play)

TC-20

20 minutes

1 hour

Cassette type

TC-30 TC-40

30 minutes

1 hour

30 minutes

Getting Started

1 Turn Tape Wheel in direction of arrow

until there is no slack.

2 Attach Battery (page 9). 3 Slide TAPE EJECT to open door. 4 Insert cassette as shown. 5 Press here to close door.

• To remove the cassette, slide the TAPE EJECT switch.

40 minutes

2 hours

• SLP playback may contain more picture noise.

Erase Protection Tab

Protects tapes from being accidentally erased.

Slide tab type

1 To prevent accidental erasing,

break off tab with screwdriver. (Or, slide tab open.)

2 To record again,

cover hole with adhesive tape. (Or, slide tab closed.)

Before Using

Attaching Shoulder Strap

Remove Battery Pack before completing the following steps:

1 Undo strap ends

from buckles.

2 Thread strap ends through Strap

Rings on Camcorder.

3 Re-insert the strap

ends into buckles.

min. 25.4 mm (1 inch)

Adjust the Length of the Shoulder Strap

Pull a loop of strap from buckle, then pull

strap tight to shorten or lengthen.

Hand Strap

Adjust Hand Strap length to fit your hand as shown.

Lens Cap

Attaching the Lens Cap Strap:

Thread the Strap through the Lens Cap attachment ring as illustrated at left.

Attaching the Lens Cap Cord to the Hand Strap:

Remove the Hand Strap from the front clasp and thread the Strap through the loop in the Lens Cap Cord. Reattach the Hand Strap.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Using MENU Mode

1, 2, 3, 4

MENU Mode (CAMERA) Screen

1 2 3 4 5 6

7 8 9

MENU Mode (VCR) Screen

5 2

Before you begin...

• Connect Camcorder to power source.

• Set POWER to CAMERA or VCR.

1 Press MENU for MENU mode.

The CAMERA or VCR MENU screen (see below left) appears when Menu mode is entered.

2 Press UP or DOWN to highlight the

desired menu item.

3 Press DISPLAY to set selection. 4 Press MENU to exit.

Note:

• The Menu mode is canceled if DISPLAY, or MENU are not pressed within 5 minutes when Self Demo mode is off.

• The Menu mode is canceled if DISPLAY, or MENU are not pressed within 30 seconds when Self Demo mode is on.

1 PROGRAMMED REC (page 19).

Camcorder starts and stops recording at a preset time.

2 DISPLAY (page 31).

ON : On-screen Display (OSD) screens are

displayed.

3 SHUTTER (page 25).

Select desired shutter speed.

4 STAND-BY RELEASE (page 18).

ON : Enables quick resumption of recording

from Stand-by mode.

5 CLOCK SET (pages 14, 15).

Select to set clock.

6 LIGHT MODE (page 16).

ON/OFF : Light can be set ON or OFF. ON/OFF/AUTO : Light can be set ON, OFF, or AUTO.

7 SELF DEMO (page 7).

ON : SELF DEMO screen is displayed.

8 MOTIONSENSOR (page 30).

ON : Enables MotionSensor recording.

9 VIDEO EFFECTS (pages 26~27).

AUTO FADE : BLACK or WHITE DIGITAL FADE : TYPE

COLOR 8 colors

UP/DOWN,

7 types

Getting Started

Setting the Clock

Set the following items in order: Time Zone, Daylight Saving Time, Date, and Time.

1, 2, 3, 4

Before you begin...

• Connect Camcorder to power source.

• Set POWER to CAMERA or VCR.

1 Press MENU for MENU mode.

Press UP or DOWN to select CLOCK SET .

[ VCR MODE ][ CAMERA MODE ]

2 Press DISPLAY for

CLOCK SET menu. Press UP or DOWN to select TIME ZONE, DST,

or DATE/TIME.

3 Press DISPLAY for menu of item selected in

step 2.

To change the setting:

TIME ZONE ➔ Go to step 3a on page 15. D.S.T. ➔ Go to step 3b on page 15. DATE/TIME ➔ Go to step 3c on page 15.

4 Press MENU twice to exit.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Setting the Clock

The Camcorder is preset to Eastern time.

Clock will auto-adjust to daylight saving time (DST).

Autumn (Last Sunday in October) :

back one hour.

Setting the Time Zone

[ Time Zone chart ]

Auto Daylight Saving Time

DST: AUTO

Spring (First Sunday in April) :

ahead one hour.

Press

select local time zone. Press DISPLAY to confirm entry.

• When traveling, repeat this operation and

select one of the 8 listed time zones to set the clock to local time.

Note :

• Clock may lose or gain up to 2 minutes

per month.

• When traveling outside the listed time zones, set clock to local time manually.

• To adjust or set clock, see “Setting Date and Time” bottom of page.

The Camcorder is preset to DST: AUTO . If DST is not observed in your area, set to OFF by doing the following.

Press UP or DOWN to

select OFF or AUTO. Press DISPLAY to confirm entry.

Note:

• Auto DST does not function if time zone is set to Hawaii or Samoa (see “Setting the Time Zone” above).

Getting Started

UP or DOWN to

Date and time including leap year are calculated up to DEC 31, 2099.

Setting Date and Time

EXAMPLE :

Press or hold down DOWN to select hour, then press

DISPLAY to fix.

Repeat for minute, month, day, and year.

Clock starts when year is entered and pressed.

DISPLAY is

UP or

Built-in Auto Light

Using the Light

For recording in dim lighting.

LIGHT

1, 2, 3

CAUTION: Light becomes hot. Never cover Light while on.

Note:

• Using Light reduces battery operating time.

• Provide proper ventilation when using

Light extensively in a hot environment.

• Using Light when the Camcorder is powered by a car battery may shorten bulb life.

• Set Light to OFF when not in use.

Replacing the Bulb

Before you begin...

• Connect Camcorder to power source.

• Set POWER to CAMERA.

1 Press MENU for

MENU mode. Press UP or DOWN to select LIGHT MODE .

2 Press DISPLAY to set OFF/ON or

OFF/ON/AUTO. Press MENU to exit.

3 Press LIGHT repeatedly for Light ON,

OFF, or AUTO.

• In AUTO, light turns itself on/off according to lighting conditions.

EVF or LCD Monitor

A : Light is on.

A : Light mode is auto.

Before you begin...

• Order Part No. VLLW0015 for replacement bulb.

• Set POWER to OFF.

1 Slightly raise portion A of lens cover

to unhook, and slide portion B forward to remove.

2 Using Tweezers or needle-nose pliers,

carefully remove bulb.

•

Take unit to service center if you need assistance.

3 Replace bulb using a clean cloth or

tissue. (Do not touch with fingers.)

4 Replace lens cover.

Note:

• Handle bulb gently. Excessive force may

DANGER:

Use only replacement bulb (PART NO. VLLW0015) supplied by Panasonic to reduce risk of fire. Handle new bulb with cloth or tissue as skin oils will decrease bulb life. Remove lens cover and allow bulb to cool before replacing to avoid possible burn hazard.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

cause bulb to crack.

Camera Recording

Recording via EVF or LCD Monitor

View recording scene on EVF (Electronic Viewer Finder) or LCD (Liquid Crystal Display) monitor.

BRIGHT ADJUSTMENT

CAUTION :

Rotating partially open LCD monitor may block cassette door and damage Camcorder body.

VISION ADJUSTMENT

Built-in Microphone

2, 6

WARNING :

• Do not leave the camcorder with the EVF aimed directly at the sun. This may cause damage to the internal parts of the EVF.

Note:

• When Camcorder is aimed at excessively bright objects, or bright lights, a vertical bar may appear in the picture. This is normal for the CCD pick-up. Try to avoid this when possible.

• Using LCD monitor reduces battery operation time. Return LCD monitor to locked position when not in use.

Before you begin...

• Connect Camcorder to power source.

• Insert cassette with record tab (page 11).

1 Press LCD-OPEN to unlock the LCD

monitor. Swing LCD monitor fully open and adjust viewing angle.

• If you want to record using EVF, close and lock LCD monitor.

2 Set POWER to

CAMERA.

• Be sure POWER is fully turned to CAMERA position.

• EVF or LCD monitor turns on/off by the POWER switch.

• EVF shuts off when LCD monitor is opened and turns back on when LCD is closed.

• Both EVF and LCD monitor turn on when LCD is at 180° (see above left). This allows both you and the subject to view the recording.

EVF or LCD Monitor

(Record/Pause mode)

3 LCD : Press BRIGHT

ADJUSTMENT

to adjust LCD monitor brightness level.

EVF : Look into EVF and adjust

VISION ADJUSTMENT to your

eyesight.

4 Hold down TAPE SPEED for about 1

second to change tape speed to SP/SLP (page 11).

Tape speed

5 Press RECORD/

PAUSE to start or

pause recording.

6 Set POWER to

OFF when finished.

• To remove the cassette, slide the TAPE EJECT switch (page 11).

EVF or LCD Monitor

(Record mode)

Basic Operation

Camera Recording

Before you begin...

• Connect Camcorder to power source.

• Insert cassette with record tab (page 11).

2, 3, 4

1, b, c,

a, d, D

A, C

Stand-by Quick Release

If left in RECORD/PAUSE mode for 5 minutes, Camcorder switches to Stand-by mode to conserve battery. When set to ON, Stand-by Quick Release lets you resume recording by pressing times. Stand-by Quick Release is set to OFF at the factory.

RECORD/PAUSE two

1 Set POWER to

CAMERA.

2 Press MENU for

MENU mode.

UP or DOWN

Press

to select STAND-BY RELEASE .

3 Press DISPLAY to select ON/OFF.

ON : From Stand-by mode, press

RECORD/PAUSE two times to resume recording.

OFF : From Stand-by mode, set

POWER to OFF, then to CAMERA. Press RECORD/ PAUSE to record.

4 Press MENU to exit.

Manual Easy Editing

For proper continuity when taping from Stop mode or after attaching a new Battery.

ASet POWER to VCR. Ba Press REWIND/SEARCH to rewind

a few seconds of tape.

b Press c Press

PLAY to review recording. STILL where you want to

continue recording.

CSet POWER to CAMERA. DPress RECORD/PAUSE to resume

recording.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Easy Edit Stand-by

For a smooth transition between scenes if recording is stopped, and then started within 24 hours.

a Press RECORD/PAUSE to stop

recording.

bSet POWER to OFF and leave cassette

in Camcorder.

c To resume recording, set POWER to

CAMERA.

dPress RECORD/PAUSE to resume

recording.

Note:

• Use Manual Easy Edit (left) if more than 24 hours before recording is resumed.

Camera Recording

Programmed Recording

Set a recording start and stop time. Or, set a 5 or 10 second interval recording to be done each minute.

1, 2, 3

Before you begin...

• Connect Camcorder to power source. Use AC Adaptor for longer recordings.

• Insert cassette with record tab (page 11).

• Set POWER to CAMERA.

1 Press MENU for MENU

mode. Press UP or

DOWN to select

PROGRAMMED REC .

2 Press DISPLAY.

(Current time is displayed.)

Each additional press of DISPLAY increases

start time by 30 minutes.

3 Press DOWN to select

REC TIME .

Press DISPLAY

repeatedly to select one of the options shown at left.

To cancel the setup, press

MENU twice.

Basic Operation

REC TIME :

*1 Record 5 seconds each minute. *2 Record 10 seconds each minute.

4 Press RECORD/PAUSE

to place Camcorder in stand-by mode.

Recording will be done as scheduled.

Note:

• Start time may not be set over 24 hours from current time.

• Camcorder shuts off at tape end, or 12 hours after Interval Recording starts.

• To cancel, set

POWER to OFF.

Playing Back Recordings

Before you begin...

• Connect Camcorder to power source.

• Insert recorded tape.

STILL

Speaker

BRIGHT ADJUSTMENT

Playback on EVF or LCD Monitor

Press LCD-OPEN and swing LCD

monitor fully open.

• If you want to playback on EVF, close and lock LCD monitor.

Set POWER to VCR.

• If tape has no record tab, auto playback begins.

• EVF or LCD monitor turns on/off by the POWER switch.

• EVF shuts off when LCD monitor is opened and turns back on when LCD is closed.

Playback function buttons.

REW : Rewind tape.

PLAY : Play tape.

STOP : Stop tape. BRIGHT :

D E VOLUME: During playback, adjust

Press “T” : Volume

Press “W” : Volume

Note:

• Using LCD monitor reduces battery operating time. Return LCD monitor to locked position when not in use.

Adjust LCD monitor brightness.

volume of speaker.

up (+).

down (-).

Tracking Control

Auto Tracking

Continuously analyzes each recording for optimum picture quality.

Manual Tracking

Some recordings require manual adjustment to reduce noise.

UP or DOWN until Playback picture

Press

clears up.

DISPLAY to return to Auto Tracking.

Press

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Special Effects

Quick Visual Search

Search Speed

• SP (Standard Play) : 3 times normal.

• SLP (Super Long Play) : 9 times normal.

During playback, press:

• FF : fast forward search

• REW : rewind search

Press again or press PLAY for normal play.

Still Picture

Press STILL to freeze picture. Press again for normal play.

This feature works best in SLP mode (page 11).

Note:

• During search, horizontal noise bars will appear.

Audio is muted.

• To protect video heads and tape, operating

modes will revert as follows after 5 minutes: Still Stand-by Stand-by Power off (when Battery Pack is

• Tape auto-rewinds if played or fast forwarded to end.

used).

Playing Back Recordings

TV Playback or Viewing

Connect Camcorder to a TV to view playback or recordings in progress.

Connections

Audio/ Video Out

VCR Playback using PlayPak

Load Battery in PlayPak

Remove Battery lid and insert AA battery.

• Do not reverse polarity.

• Replace battery when tape loading/unloading takes longer

than usual.

Insert Cassette in PlayPak

Before you begin...

• Connect Camcorder to power source.

• Make all TV-Camcorder connections.

1 Set POWER to:

VCR ➞ view playback. CAMERA ➞ view picture as it is

recorded.

2 Turn TV ON and set to LINE INPUT.

See TV owner’s manual.

3 Begin playback or recording.

Basic Operation

1 2

• Do not obstruct cassette

Remove Cassette

reel while loading.

• Allow PlayPak Load Detector to fully retract before using in VHS VCR.

1 Turn cassette Tape Wheel in direction of

arrow to take up any slack.

2 Slide RELEASE to open cassette lid. 3 Insert the cassette with the window up and on

the left, then snap lid shut.

Load Detector

1 Slide RELEASE and wait for lid to open. 2 Push cassette out through hole in bottom of

PlayPak with your finger.

Copying your Tapes (dubbing)

Connections

STOP

Source (Playing) Camcorder

Audio/ Video Out

PLAY

STILL

Before you begin...

• Make Camcorder-VCR connections (see left).

• Turn both units on.

• Set VCR input signal to LINE. Please see VCR owner’s manual.

• Set Camcorder POWER to VCR.

Insert a pre-recorded tape

into Camcorder and a blank tape with record tab into VCR.

Press PLAY on Camcorder, then press

STILL at starting point.

Press REC, then STILL/PAUSE on

VCR.

Press STILL on Camcorder and STILL/

PAUSE on VCR to start copying.

Press STOP on both units to stop

copying.

Note:

• Camcorder will only playback tapes

recorded in SP or SLP mode.

• Dubbing may reduce picture quality.

CAUTION:

Unauthorized exchanging and/or copying of copyrighted recordings may be copyright infringement.

Monitor with your TV

• Turn TV on and tune to VCR channel (CH3 or CH4).

• Set TV/VCR Selector on VCR to VCR.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Four-Speed Power Zoom

Zoom in (close up) and out (wide angle) in one of four speeds ranging from slow (16 seconds) to fast (2 seconds).

Use when subject is darker than surroundings, in shadowed area, or in front of the light source.

Before you begin...

• Connect Camcorder to power source.

• Set POWER to CAMERA.

Zoom In (“T”)

Zoom Out (“W”)

• Zoom slowly:

Lightly press “T” (telephoto) or “W” (wide angle) POWER ZOOM button.

• Zoom quickly:

Apply more pressure to the button.

Backlight

Before you begin...

• Connect Camcorder to power source.

• Set POWER to CAMERA.

Special Features

B.LIGHT

Press B.LIGHT.

Press B.LIGHT while recording to select

the level of backlight compensation.

In normal lighting, press repeatedly until no indicator is displayed.

EVF or LCD Monitor

B.LIGHT

Focus

Before you begin...

• Connect Camcorder to power source.

• Set POWER to CAMERA.

Auto Focus

Camcorder automatically focuses on subject even during zooming.

Auto Focus is on when “MF” is not displayed in EVF or LCD monitor.

M.FOCUS to remove “MF” in EVF or LCD monitor if necessary.

Press

Manual Focus

Use Manual Focus (MF) when :

• recording through glass.

• lighting is poor.

• subject is far away with objects in foreground.

• subject has distinct horizontal lines.

• subject is not centered in EVF or LCD monitor.

• subject has a shiny surface.

• subject is slanted.

• subject is bright and flat, like a white wall.

• subject has fast motion, like a golf swing.

EVF or LCD Monitor

1 Press M.FOCUS so “MF” (Manual Focus)

appears in EVF or LCD monitor.

2 Hold down “T” (telephoto) on POWER

ZOOM to maximum zoom in.

3 Press UP (FAR) or DOWN (NEAR) until

subject is in focus.

• Back away from subject if necessary.

4 Hold down “W” (wide angle) on POWER

ZOOM as desired.

Macro Focus (close-ups)

Auto Focus functions up to 12.7 mm (1/2 inch) from subject.

Hold down “ Bring Camcorder up close to the subject.

W” on POWER ZOOM to maximum wide angle.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

• Refocus as needed when aiming at new

scenes.

High Speed Shutter

Improves Still or Slow Motion playback picture of high speed subjects (e.g. a tennis stroke), when viewed on Camcorder or 3 or 4 head VCR.

Before you begin...

• Connect Camcorder to power source.

• Insert cassette with record tab (page 11).

• Set POWER to CAMERA.

Auto Shutter

In AUTO mode (no indication in EVF or LCD Monitor), shutter speed is auto-adjusted from 1/60 to 1/350 according to subject brightness.

• AUTO mode is selected each time POWER is set to CAMERA.

Manual Selection

The faster the shutter speed, the more light is needed for proper picture and color quality. High Speed Shutter indication flashes if light is inadequate. Provide additional light.

1 Press MENU for MENU mode.

Press UP or DOWN to select SHUTTER .

2 Press DISPLAY repeatedly to select

shutter speed.

Special Features

1, 2, 3

3 Press MENU to exit.

Note:

• Shutter speed cannot be set to 1/60 if Digital E.I.S. feature is set to ON.

• Provide additional halogen or tungsten light for use indoors or in poor light. Fluorescent light degrades picture.

• Auto Focus may not function properly if high speed shutter is used in inadequate light.

• Setting reverts to AUTO each time POWER is set to CAMERA.

Auto Fade

An interesting way to open and close scenes.

FADE

1, 2, 3, 4

RECORD/ PAUSE

Before you begin...

• Connect Camcorder to power source.

• Set POWER to CAMERA.

1 Press MENU for

MENU mode.

Press UP or DOWN

to select

VIDEO EFFECTS .

2 Press DISPLAY for

VIDEO EFFECTS menu. Press UP or

DOWN to select

AUTO FADE .

3 Press DISPLAY for

AUTO FADE ; COLOR menu.

Press UP or DOWN

to select BLACK or WHITE.

4 Press DISPLAY to confirm entry.

Press MENU to exit.

Fade In

Fade In:

In RECORD/PAUSE mode, press FADE

so “FADE” flashes in EVF or LCD monitor.

RECORD/PAUSE.

Press

Recording starts as picture and sound gradually fade in.

Fade Out:

While recording, press FADE so “FADE”

flashes in EVF or LCD monitor.

RECORD/PAUSE.

Press

Picture and sound gradually fade out, and recording is paused.

FADE is pressed accidentally, press again

BLACKWHITE

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Fade Out

so “FADE” disappears in EVF or LCD monitor.

+ 58 hidden pages