Panasonic PV-GS50-K Operating Instructions

PV-GS50P.book 1 ページ２００３年２月１７日　月曜日　午後６時３０分

Digital Video Camcorder

Operating Instructions

Model No.

PV-GS50

PV-GS50-K

Mini

Before attempting to connect, operate or adjust this product, please read these instructions thoroughly.

Spanish Quick Use Guide is included. Guía para rápida consulta en español está incluida.

For USA assistance, please call: 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.ca

LSQT0672A

PV-GS50P.book 2 ページ２００３年２月１７日　月曜日　午後６時３０分

Things You Should Know

Date of Purchase

Thank you for choosing Panasonic!

You have purchased one of the most sophisticated and reliable products on the market today. Used properly, we’re sure it will bring you and your family years of enjoyment. Please take time to fill in the information on the right. The serial number is on the tag located on the underside of your Palmcorder. Be sure to retain this manual as your convenient Palmcorder information source.

Dealer Purchased From

Dealer Address

Dealer Phone No.

Model No.

Serial No.

Safety Precautions

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

Your Palmcorder is designed to record and play back in Standard Play (SP) mode and

Long Play (LP) mode It is recommended that only cassette tapes that have been tested and inspected for use in Palmcorder with the

RISK OF ELECTRIC SHOCK

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

mark be used.

CAUTION

DO NOT OPEN

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

The above markings are located on the appliance bottom cover.

PV-GS50P.book 3 ページ２００３年２月１７日　月曜日　午後６時３０分

FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

≥Reorient or relocate the receiving antenna. ≥Increase the separation between the equipment and receiver. ≥Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ≥Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, follow the attached installation instructions and use only shielded interface cables with ferrite core when connecting to computer or peripheral devices. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Declaration of Conformity Trade Name: Panasonic Model No.: PV-GS50 Responsible party: Matsushita Electric Corporation of America

Support Contact: Panasonic Consumer Electronics Company

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

One Panasonic Way, Secaucus, NJ 07094

1-800-211-PANA (7262)

CAUTION: TO PREVENT FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,

CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE

≥Since this product gets hot during use, operate it in well ventilated place; do not install this equipment

in a confined space such as a bookcase or similar unit.

RECOMMENDED ACCESSORIES ONLY.

FULLY INSERT.

ONLY WITH THE SAME OR EQUIVALENT TYPE.

PV-GS50P.book 4 ページ２００３年２月１７日　月曜日　午後６時３０分

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or the table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

S3125A

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

PV-GS50P.book 5 ページ２００３年２月１７日　月曜日　午後６時３０分

Precautions

USE & LOCATION

≥TO AVOID SHOCK HAZARD ... Your

Palmcorder and power supply should not be exposed to rain or moisture. Do not connect the power supply or operate your Palmcorder if it gets wet. Your Palmcorder has been designed for outdoor use, however it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or a direct splashing from a pool or even a cup of coffee. This action could permanently damage the internal parts of your Palmcorder. Do not attempt to disassemble this unit. There are no user serviceable parts inside. Unplug your Palmcorder from the power supply before cleaning.

≥DO NOT AIM YOUR PALMCORDER AT THE

SUN OR OTHER BRIGHT OBJECTS

≥DO NOT LEAVE THE PALMCORDER WITH

THE EVF AIMED DIRECTLY AT THE SUN AS THIS MAY CAUSE DAMAGE TO THE INTERNAL PARTS OF THE EVF

≥DO NOT EXPOSE YOUR PALMCORDER TO

EXTENDED HIGH TEMPERATURE ... Such as,

in direct sunlight, inside a closed car, next to a heater, etc... This action could permanently damage the internal parts of your Palmcorder.

≥AVOID SUDDEN CHANGES IN

TEMPERATURE ... If the unit is suddenly

moved from a cold place to a warm place, moisture may form on the tape and inside the unit.

≥DO NOT LEAVE YOUR PALMCORDER OR

THE POWER SUPPLY TURNED ON WHEN NOT IN USE.

≥STORAGE OF YOUR PALMCORDER ... Store

and handle your Palmcorder in a manner that will not subject it to unnecessary movement (avoid shaking and striking). Your Palmcorder contains a sensitive pick-up device which could be damaged by improper handling or storage.

CARE

≥TO CLEAN YOUR PALMCORDER ... Do not

use strong or abrasive detergents when cleaning your Palmcorder body.

≥TO PROTECT THE LENS ... Do not touch the

surface of the lens with your hand. Use a commercial Palmcorder lens solution and lens paper when cleaning the lens. Improper cleaning can scratch the lens coating.

≥TO PROTECT THE FINISH OF YOUR

PALMCORDER ... Before handling your

Palmcorder, make sure your hands and face are free from any chemical products, such as suntan lotion, as it may damage the finish.

This class B digital apparatus complies with CANADIAN ICES-003.

This Product has a fluorescent lamp that contains a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www.eiae.org

U.S.A./CANADA CONSUMERS: ATTENTION:

A lithium ion/polymer battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery.

PV-GS50P.book 6 ページ２００３年２月１７日　月曜日　午後６時３０分

Before opening the CD-ROM package, please read the following.

End User License Agreement (for USB Driver, SD Viewer and DV STUDIO)

You (“Licensee”) are granted a license for the Software defined in this End User Software Agreement (“Agreement”) on condition that you agree to the terms and conditions of this Agreement. If Licensee does not agree to the terms and conditions of this Agreement, promptly return the Software to Matsushita Electric Industrial Co., Ltd. (“Matsushita”), its distributors or dealers from which you made the purchase.

Article 1 License Licensee is granted the right to use the software, including the information recorded or described on the CD-ROM, instruction manuals, and any other media provided to Licensee (collectively “Software”), but all applicable rights to patents, copyrights, trademarks and trade secrets in the Software are not transferred to Licensee.

Article 2 Use by a Third Party Licensee may not use, copy, modify, transfer or allow any third party, whether free of charge or not, to use, copy or modify the Software, except as expressly provided for in this Agreement.

Article 3 Restrictions on Copying the Software Licensee may make a single copy of the Software in whole or in part solely for back-up purpose.

Article 4 Computer Licensee may only use the Software on a single computer at a single location.

Article 5 Reverse Engineering, Decompiling or Disassembly Licensee may not reverse engineer, decompile, or disassemble the Software, except to the extent either of them is permitted under law or regulation of the country where Licensee resides. Matsushita, or its distributors or dealers will not be responsible for any defects in the Software or damage to Licensee caused by Licensee’s reverse engineering, decompiling, or disassembly of the Software.

Article 6 Limitation of Liability The Software is provided “AS-IS” without warranty of any kind, either expressed or implied, including, but not limited to, warranties of non-infringement, merchantability and/or fitness for a particular purpose. Further, Matsushita does not warrant that the operation of the Software will be uninterrupted or error free. Matsushita or any of its distributors or dealers will not be liable for any damage suffered by Licensee arising from or in connection with Licensee’s use of the Software.

Article 7 Export Control Licensee agrees not to export or re-export to any country the Software in any form without the appropriate export licenses under regulations of the country where Licensee resides, if necessary.

Article 8 Termination of License The right granted to Licensee hereunder will be automatically terminated if Licensee violates any of the terms and conditions of this Agreement. Upon such automatic termination, Licensee must destroy the Software and related documentation together with all the copies thereof at Licensee’s own expense.

PV-GS50P.book 7 ページ２００３年２月１７日　月曜日　午後６時３０分

Before opening the CD-ROM package, please read the following.

G.726 Audio Decoder End User License Agreement

YOU SHOULD CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS. THIS IS A LEGAL DOCUMENT WHICH CONSTITUTES YOUR AGREEMENT AS END USER FOR THE USE OF THE SOFTWARE IN THAT PACKAGE. BY INSTALLING THIS SOFTWARE, YOU INDICATE YOUR ACCEPTANCE OF THIS LIMITED USE SOFTWARE LICENSE. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE DISK PACKAGE AND THE ACCOMPANYING ITEMS WITH YOUR SALES RECEIPT TO YOUR VENDOR.

LIMITED USE SOFTWARE LICENSE

You, the Licensee, are granted a non-exclusive software license to use the Software and related documentation supplied herein. The terms of this license are as follows:

1) You may use the Software on a single computer at a single location.

2) As you, the Licensee, own the physical media on which the Software is recorded, the Licensor of the Software retains title and ownership thereof, regardless of the form or media in or on which the original and other copies may exist. This License is not a sale of the original Software or any copy thereof.

3) You are required to protect the copyright of the Software. You may NOT distribute or otherwise make the Software or documentation available to any third party without the prior written consent of the Licensor. You may be held legally responsible for any copyright infringement that is caused or encouraged by your failure to abide by the terms of this License.

4) You may NOT modify or alter the Software. Any portion of the Software that is merged into or used in conjunction with other software will continue to be the property of the Licensor and will be subject to the terms of this License.

5) You are permitted to copy the Software for exclusive use as your working copy. Any such copy must contain the same copyright notice and proprietary marking as the original Software.

6) You may not transfer or assign the Software or this License to any other person without the prior written consent of the Licensor. Any authorized transferee of the Software shall be bound by the same terms and conditions of this License and, in such case your license is automatically terminated. In no event may you transfer, assign, rent, sell, or otherwise dispose of the Software on a temporary or permanent basis except as expressly provided herein.

7) This License is effective until terminated. This License will terminate automatically without notice from the Licensor if you fail to comply with any provision of this Agreement. Upon termination you will destroy the Software together with all copies and modifications in any form.

8) The Software has been tested and the documentation has been reviewed. However, THE LICENSOR MAKES NO WARRANTY OR REPRESENTATION INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE, ALL OF WHICH ARE EXCLUDED. Some states do not allow exclusion of implied warranties so the above disclaimer may not apply to you.

9) The Licensor will not be liable or in any way responsible for any incidental or consequential economic or property damage in connection with the Software or its documentation. Some states do not allow the exclusion of incidental or consequential damages so the above exclusion may not apply to you.

10) (Notice to U.S. Government End Users) The Software and Documentation are “Commercial Items”, as that term is defined at 48 C.F.R. 2.101, consisting of “Commercial Computer Software” and “Commercial Computer Software Documentation”, as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through

227.7202-4, as applicable, the Commercial Computer Software and Commercial Computer Software Documentation are being licensed to U.S. Government end users (A) only as Commercial Items and (B) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.

PV-GS50P.book 8 ページ２００３年２月１７日　月曜日　午後６時３０分

Contents

Standard Accessories ..........................................10

Before Using

Quick Guide .........................................................12

To View the Playback Picture ..............................12

Controls and Components ...................................13

Remote Controller................................................15

Power Supply.......................................................18

Charging Time and Available Recording

Time .................................................................18

Lens Cap and Easy-Grip Strap ............................19

Attaching the Shoulder Strap ...............................20

Inserting a Cassette .............................................20

Turning on/off the Palmcorder and Selecting

Modes ..............................................................20

Using the Viewfinder............................................21

Using the LCD Monitor.........................................21

Using the Menu Screen .......................................22

List of Menus........................................................23

Setting Date and Time .........................................27

Internal Lithium Battery Recharge .......................27

LP Mode...............................................................27

Audio Recording Mode ........................................27

CAMERA Mode

Recording.............................................................28

Quick Start ...........................................................29

Self-timer Recording............................................30

PhotoShot Recording on the DV Cassette...........30

Zoom In/Out Functions ........................................31

Digital Zoom Function ..........................................31

Digital Electronic Image Stabilizer Function.........32

Fade In/Out Functions .........................................32

Cinema Function..................................................33

Backlight Compensation Function .......................33

MagicPix Function................................................34

Wind Noise Reduction Function...........................34

Recording in Special Situations (Program AE) .... 35

Manual Shutter Speed Adjustment ......................36

Manual Iris Adjustment (F Number) .....................36

Manual Focus Adjustment ...................................37

Recording in Natural Colors (White Balance) ......37

Adjusting White Balance Manually.......................38

Digital Effect Functions ........................................39

Playing Back........................................................42

VCR Mode

Finding a Scene You Want to Play Back .............43

Slow Motion Playback..........................................44

Still Playback/Still Advance Playback ..................44

Finding the End of a Recording

(Blank Search Function)...................................45

Playback Zoom Function .....................................45

Index Search Functions .......................................46

Playback Digital Effect Functions.........................47

Playing Back on Your TV.....................................49

Audio Dubbing .....................................................50

Special Features

Using a Memory Card..........................................51

Recording on the Memory Card...........................52

Playing Back Files from the Memory Card...........56

Copying Pictures from a Memory Card to

a Cassette........................................................59

Slide Show...........................................................60

Creating a Title.....................................................61

Inserting a Title ....................................................62

Protecting the Files on a Memory Card from

Accidental Erasure (File Lock) .........................63

Deleting the Files Recorded on

a Memory Card ................................................64

Formatting a Memory Card ..................................65

DPOF Setting.......................................................65

Copying your DV Cassette to an S-VHS or

VHS Cassette (Dubbing)..................................66

Copying an S-VHS or VHS Cassette to your

DV Cassette.....................................................66

Using your Palmcorder with Digital Video

Equipment (Dubbing) .......................................67

Using the Software with a Computer ...................68

Using USB Driver.................................................68

Installing USB Driver............................................69

Connecting Computer and Palmcorder................70

Using as a Web Camera......................................71

Using the DV STUDIO 3.1E-SE...........................73

Using the G.726 Audio Decoder ..........................74

Using the ArcSoft Software..................................75

To disconnect USB cable safely...........................77

If you no longer need software or driver

(Uninstall).........................................................77

Notes....................................................................78

PV-GS50P.book 9 ページ２００３年２月１７日　月曜日　午後６時３０分

Before Use CAMERA VCR

Others

Indications............................................................80

Initializing the Modes ...........................................83

Warning/Alarm Indications...................................83

Notes & Precautions............................................84

Cautions for Use ..................................................92

Explanation of Terms ...........................................95

Specifications.......................................................97

Palmcorder Accessory System ............................98

Palmcorder Accessory Order Form

(For USA Customers).......................................99

Before Requesting Service

(Problems and Solutions)...............................100

Request for Service Notice (USA Only) .............103

Limited Warranty (For USA Customers) ............104

Customer Services Directory .............................105

Warranty (For Canadian Customers) .................106

Index ..................................................................107

Spanish Quick Use Guide/

Guía española para el uso rápido..................109

Special Features

Others

PV-GS50P.book 10 ページ２００３年２月１７日　月曜日　午後６時３０分

Before Using

PV-DAC13

CR2025

N2QCBD000030

CGA-DU07

N2QAEC000003

Standard Accessories

Illustrated on the left are accessories packaged with the Palmcorder.

1) AC Adaptor, DC Cable and AC Cable (l 18)

≥Supplies power to the Palmcorder.

CAUTION:

This unit will operate on 110/120/220/240 V AC. An AC plug adaptor may be required for voltages other than 120 V AC. Please contact either a local or foreign electrical parts distributor for assistance in selecting an alternate AC plug. We recommend using the accessory power plug adaptor (VJSS0070) in an area which has special AC outlets.

2) Battery Pack (l 18)

≥Supplies power to the Palmcorder.

3) Remote Controller and Button-Type Battery (l 15, 16, 17)

4) MagicWire Remote Control with Narration Mic (l 16)

5) Lens Cap (l 19)

6) A/V Cable (l 49)

7) S-Video Cable (l 49)

K2KC4CB00009

K2KC4CB00008

VYF2887

PV-GS50P.book 11 ページ２００３年２月１７日　月曜日　午後６時３０分

Before Use

8) Shoulder Strap (l 20)

9) SD Memory Card (l 78)

10) CD-ROM:

USB Driver for Panasonic DVC (l 68) DV STUDIO 3.1E-SE (l 73) G.726 Audio Decoder (l 74)

VFC3506

ArcSoft Software (l 75)

≥Macintosh is a registered trademark of Apple Computer, Inc. 2001.

ArcSoft, the ArcSoft logo, ArcSoft PhotoImpression 4.0, ArcSoft PhotoBase 4.0, ArcSoft Panorama Maker 3.0 and PhotoPrinter 4.0 are trademarks of ArcSoft, Inc.

≥Microsoft

Windows®, NetMeeting® and DirectX®, are registered

trademarks of the Microsoft Corporation U.S.A.

RP-SD008BVE0

10)

≥Intel

, Pentium®, and Celeron® are the registered trademarks or

trademarks of the Intel Corporation.

≥All other names, company names, product names, etc. in these

instructions are the trademarks or registered trademarks of their respective corporations.

≥The names of the products you are using may differ from the

VFF0193

names given in the text. Depending on the operating environment and other factors, the contents of the screens used in these

11)

instructions may not necessarily match what you will see on your screen.

≥Although the screens in these Operating Instructions are shown in

English for the sake of example, other languages are supported as well.

VFA0397

≥In this Manual, the Panasonic make digital video camera with USB

Terminal is referred to as Palmcorder.

≥These instructions do not cover the basic operations of the

personal computer or define any terms. For this information, refer to the Operating Instructions which accompany your personal computer.

11) USB Cable (l 68)

............................................................................................................

Extremely high precision technology is employed to produce the LCD Monitor screen featuring a total of approximately 113,000 pixels. The result is more than 99.99% effective pixels with a mere 0.01% of the pixels inactive or always lit. However, this is not a malfunction and does not affect the recorded picture.

............................................................................................................

PV-GS50P.book 12 ページ２００３年２月１７日　月曜日　午後６時３０分

Quick Guide

1 Charge the Battery. (l 18)

≥Connect the AC Cable to the AC Adaptor and plug it into the

AC Wall Outlet.

≥Attach the Battery to the AC Adaptor. (This will start the

charging process.)

≥The [POWER] Lamp and [CHARGE] Lamp light up, and

charging starts. When the [CHARGE] Lamp goes off, charging is completed.

≥Since the Battery will not be charged when the DC Cable is

connected to the AC Adaptor, disconnect it.

2 Attach the Charged Battery to the Palmcorder. (l 18)

3 Insert the Cassette. (l 20)

≥Slide the [OPEN/EJECT]

down to open the Cassette Compartment.

≥Insert the Cassette. ≥Press [PUSH CLOSE]

2 to load the Cassette.

≥Close the outside compartment Cover.

PUSH

OPEN / EJECT

1 Lever toward the front and pull

5, 6

CAMERA VCR

CARD PB

≥Turn the Palmcorder on. (l 20) ≥Rotate the Switch ≥Press the ≥Press the

3 to [ON]. (The [CAMERA] Lamp lights up.) 4 Button. (Recording starts.) 4 Button again to pause the recording.

To View the Playback Picture

5 Switch to the VCR Mode, rewind the tape, and play

4 Start recording. (l 28)

the tape back.

≥Set the

CAMERA VCR

CARD PB

FADE

BACK LIGHT

≥Press the ≥Press the ≥Press the

6 Turn the Palmcorder off. (l 20)

≥Set the 9 Switch to [OFF].

(l 42)

5 Switch to VCR mode. (The [VCR] Lamp lights up.)

6 Button. (Rewind the tape.) 7 Button. (Playback starts.) 8 Button. (Playback stops.)

PV-GS50P.book 13 ページ２００３年２月１７日　月曜日　午後６時３０分

Before Use

Controls and Components

1) LCD Monitor (l 21, 95)

............................................................................................................

≥Due to limitations in LCD production technology, there may

be some tiny bright or dark spots on the LCD Monitor screen. However, this is not a malfunction and does not affect the recorded picture.

............................................................................................................

2) LCD Monitor Open Knob [OPEN 4] (l 21)

3) Accessory Shoe

4) Card Access Lamp [ACCESS] (l 51)

5) Card Slot Cover Open Lever [OPEN] (l 51)

6) Card Slot Cover (l 51)

7) Card Slot (l 51)

8) Rewind/Review Button [6] (l 42, 43) Reverse Search Button [SEARCHs] (l 28) Recording Check Button [S] (l 28)

9) Play Button [1] (l 42, 56, 60) Backlight Button [BACK LIGHT] (l 33)

10) Fast Forward/Cue Button [5] Forward Search Button [SEARCHr] (l 28)

11) Title Button [TITLE] (l 62)

12) MAGICPIX Button [MAGICPIX] (l 34)

13) Stop Button [∫] (l 42, 56, 60)

22)

Fade Button [FADE] (l 32)

23)

14) Still Button [;] (l 44, 56, 60)

24)

Camera Still Button [STILL] (l 30)

15) Multi-Picture Button [MULTI] (l 41, 48) Picture-in-Picture Button [P-IN-P] (l 40)

16) Viewfinder (l 21, 95)

25)

............................................................................................................

≥Due to limitations in LCD production technology, there may

be some tiny bright or dark spots on the Viewfinder screen. However, this is not a malfunction and does not affect the recorded picture.

............................................................................................................

17) Eyepiece Corrector Knob (l 21)

18) Menu Button [MENU] (l 22)

19) Multi-Function Dial [PUSH] (l 22, 27, 37, 42, 44)

20) PhotoShot Button [PHOTO SHOT] (l 30, 52)

21) Zoom Lever [W/T] (l 31)

22) Cassette Eject Lever [OPEN/EJECT] (l 20)

23) Reset Button [RESET] (l 100)

24) Tape/Card Selector [TAPE/CARD/CARD MODE] (l 28, 52)

25) Easy-Grip Strap (l 19)

16)

4) 7)6)

LIGHT

MAGIC

FADE

PIX

12)

19)

17)

18)

20)

10)9)

STILL

21)

11)

TITLEBACK

MULTI P-IN-P

15)13)8)14)

(l 43)

PV-GS50P.book 14 ページ２００３年２月１７日　月曜日　午後６時３０分

26) Quick Start Recording Button [QUICK START] (l 29)

27) Quick Start Recording Lamp (l 29)

28) Recording Start/Stop Button (l 28, 55)

29) Off/On Mode Selector Switch [OFF/ON/MODE] (l 20, 28, 42)

30) Operation Mode Lamps [CAMERA/VCR/CARD PB] (l 22, 28, 42, 56)

31) Mode Selector Switch [AUTO/MANUAL/FOCUS] (l 28, 35, 37)

32) Shoulder Strap Holders (l 20)

33) Battery Eject Button [PUSH BATT] (l 18)

34) Battery Holder (l 18)

35) Tripod Receptacle

≥Use for mounting the Palmcorder on an optional tripod.

36) Cassette Holder (l 20)

37) Speaker

28)

30)

QUICK

START

26)

27)

29)

CAMERA VCR

CARD P.B

38) Cassette Compartment Cover (l 20)

31)32)

39) Cassette Holder Close Button [PUSH CLOSE] (l 20)

40) Remote Control Sensor (l 17) White Balance Sensor (l 37, 96)

41) S-Video Input/Output Jack [S-VIDEO IN/OUT] (l 49)

42) USB Jack (l 70)

43) DV Input/Output Terminal [DV] (l 67)

≥Connect this to the digital video equipment.

33) 34) 35)

44) Lens Hood (l 95)

45) Rec Lamp (l 28)

46) Lens

47) Microphone (Built-in, stereo)

36)

48) Easy-Grip Strap Lock Cover (l 19)

49) Easy-Grip Strap Release Button (l 19)

50) Audio-Video Input/Output Jack [AV IN/OUT] (l 49) Headphone Jack [PHONES] (l 88)

≥Connecting an AV Cable to this Jack activates the

Palmcorder’s built-in speaker, but connecting a headphone, etc. deactivates it.

≥When plugging the pin plug of the AV cable into the AV output

terminal, plug it in as far as it goes.

51) MagicWire Remote Control with Narration Mic Jack [REMOTE] (l 16) Microphone Jack [MIC] (l 88)

≥Connecting with an external microphone or audio equipment.

(When this Jack is in use, the built-in microphone does not operate.)

≥When connecting the remote controller to the [PHONES]

Socket, the Palmcorder may not operate properly.

52) Eyecup

37)

S-VIDEO

IN / OUT

41) 42) 43)

44)

45)

46)

38)

39)

40)

52)

47)

AV IN/OUT

REMOTE/MIC

PHONES

(PLUG IN POWER)

48)

49)

50) 51)

PV-GS50P.book 15 ページ２００３年２月１７日　月曜日　午後６時３０分

Before Use

Remote Controller

11)

12)

13)

14)

15)

20)

21)

22)

23)

24)

OSD

COUNTER

MULTI/

P-IN-P

STILL ADV

INDEX INDEX

SELECT

STORE

OFF/ON

P.B.DIGITAL

OSD

COUNTER

MULTI/

P-IN-P

STILL ADV

INDEX INDEX

SELECT

STORE

OFF/ON

P.B.DIGITAL

OSD

COUNTER

MULTI/

P-IN-P

STILL ADV

INDEX INDEX

SELECT

STORE

OFF/ON

P.B.DIGITAL

DATE/

TIME

RESET

¥REC

PLAY

/REW

615

PAUSE

STOP

DATE/

TIME

RESET

¥REC

PLAY

/REW

615

PAUSE

STOP

DATE/

TIME

RESET

¥REC

PLAY

/REW

615

PAUSE

STOP

SHOT

ZOOM

TITLE

A.DUB

sVOLr

FF/

STILL ADV

;

∫

VAR.

;

∫

VAR.

;

∫

VAR.

PHOTO

SHOT

TITLE

A.DUB

FF/

STILL ADV

PHOTO

SHOT

TITLE

A.DUB

FF/

STILL ADV

P.B.

ZOOM

SET

ITEM

START/

STOP

ZOOM

sVOLr

P.B.

ZOOM

SET

ITEM

START/

STOP

ZOOM

sVOLr

P.B.

ZOOM

SET

ITEM

START/

PHOTO

Using the wireless Remote Controller that is supplied with the Palmcorder, most of the Palmcorder functions can be operated from a distance.

Remote Controller Buttons

1) Date and Time Button [DATE/TIME] (l 83)

2) Indication Output Button [OSD] (l 49)

3) Counter Reset Button [RESET] (l 96)

4) Indication Shift Button [COUNTER] (l 83)

5) Multi-Picture/Picture-in-Picture Button [MULTI/P-IN-P]

10)

(l 40, 41, 48)

6) Recording Button [REC] (l 66, 67)

7) Audio Dubbing Button [A.DUB] (l 50)

8) Upward Direction Button [π] (for Playback Zoom Function) (l 45)

9) Left/Right Direction Button [∑, ∏] (for Playback Zoom Function) (l 45)

10) Downward Direction Button [∫] (for Playback Zoom Function) (l 45)

11) Slow Motion/Still Advance Button [E, D] (E : reverse direction, D: normal direction) (l 44)

12) Index Search Button [:, 9]

16)

(:: reverse direction, 9: normal direction) (l 46)

13) Selection Button [SELECT] (l 47)

14) Store Button [STORE] (l 47)

15) Off/On Button [OFF/ON] (l 47)

16) Zoom/Volume Button [ZOOM/VOL] (l 31, 42, 45)

17)

17) Variable Speed Search Button [VAR.SEARCH] (l 43)

18)

18) Playback Zoom Button [P.B. ZOOM] (l 45)

19)

19) Speed Selection Button [π, ∫] (for Variable Speed Search Function) (l 43)

The following buttons function in the same manner as the corresponding buttons on the Palmcorder.

20) Fast-forward/Cue Button [5] (l 43)

21) Play Button [1] (l 42, 56)

25)

22) Rewind/Review Button [6] (l 42, 43)

23) Pause Button [;] (l 44, 56)

26)

24) Stop Button [∫] (l 42, 56)

27)

25) PhotoShot Button [PHOTO SHOT] (l 30, 52)

26) Recording Start/Stop Button [START/STOP] (l 28)

27) Title Button [TITLE] (l 62)

28) Menu Button [MENU] (l 22)

29) Item Set Button [SET] (l 22)

30) Item Select Button [ITEM] (l 22)

28)

29)

30)

PV-GS50P.book 16 ページ２００３年２月１７日　月曜日　午後６時３０分

ª MagicWire Remote Control with Narration Mic

This controller allows the scene to be shot in various angles, high to low and is also convenient when a Tripod is used. When the MagicWire Remote Control with Narration Mic is not use, attach its

1 2 3 4 5

clip to the Easy-Grip Strap for convenience. This controller allows the camera to be used more conveniently by a left-handed user. ≥When using the MagicWire Remote Control with Narration MIC,

plug its connector into the [REMOTE], [MIC] Jack of the Palmcorder as far as it goes.

1 Narration Microphone [MIC] (l 29) 2 Recording Start/Stop Button [REC] 3 Zoom Lever [W/T]

≥Zoom speed changes in 2 stages.

4 PhotoShot Button [PHOTO SHOT] 5 Narration Microphone Button [TALK] (l 29)

≥When connecting the MagicWire Remote Control with

Narration Mic to [REMOTE] Jack and the [TALK] Button is pressed, the built-in microphone does not operate.

6 Clip

ª Inserting the Button-type Battery

Before using the remote controller, insert the supplied button-type battery.

1 While pressing the Stopper 1, pull out the Battery

Holder.

2 Insert the button-type battery with the imprint (i)

facing upward.

3 Insert the Battery Holder into the Remote Controller.

≥When the button-type battery becomes weak, replace it with a new

CR2025 battery. (A battery is normally expected to last about one year, however, it depends on operation frequency.)

≥Be sure to match the poles properly when inserting the battery.

............................................................................................................

Warning

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer’s instructions. Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212°F (100°C) or incinerate. Keep the Button-Type battery out of the reach of children. Never put Button-Type battery in mouth. If swallowed, call your doctor.

............................................................................................................

Replace battery with Panasonic PART NO. CR2025 only. Use of another battery may present a risk of fire or explosion. Caution: Battery may explode if mistreated. Dispose of used battery promptly. Keep away from children. Do not recharge, disassemble or dispose of in fire.

PV-GS50P_text.fm 17 ページ２００３年２月１８日　火曜日　午前９時４６分

Before Use

ª Using the Remote Controller 1

Direct the Remote Controller at the Remote Control Sensor on the Palmcorder and press the desired button.

≥Distance from the Palmcorder: Within approximately 15 feet

(5 meters)

15˚

START/

PHOTO

DATE/

SHOT

TIME

RESET TITLE

¥REC

A.DUB

FF/

PLAY

PAUSE

STILL ADV

;

STOP

∫

VAR.

STOP

ZOOM

sVOLr

P.B.

ZOOM

SET

ITEM

OSD

COUNTER

MULTI/ P-IN-P

/REW

615

STILL ADV

E D

2 1

INDEX INDEX

SELECT

STORE

OFF/ON

P.B.DIGITAL

≥Angle: Approximately 15o in the vertical and horizontal

directions from the central axis

≥The above operating ranges are for indoor use. Outdoors, or under

strong light, the equipment may not operate properly even within the above ranges.

≥Within 3 feet (1 meter) range, you can also use the Remote

Controller on the side (the LCD Monitor side) of the Palmcorder.

Selecting Remote Controller Modes

When two Palmcorders are used simultaneously, they can be operated individually by selecting different Remote Controller Modes. ≥If the Remote Controller Mode on the Palmcorder and Remote

Controller do not match, [REMOTE] is displayed.

Setting on the Palmcorder:

Set [REMOTE] on the [OTHER FUNCTIONS] Sub-Menu to the desired Remote Controller Mode.

Setting on the Remote Controller:

[VCR1]: Press the [D] Button and [∫] Button simultaneously. [VCR2]: Press the [E] Button and [∫] Button simultaneously. 2 ≥When the battery in the Remote Controller is replaced, the Mode is

automatically reset to [VCR1] Mode.

PV-GS50P.book 18 ページ２００３年２月１７日　月曜日　午後６時３０分

Power Supply

ª Using the AC Adaptor 1

Insert the battery-shaped connector of the DC Cable into the Battery Holder on the Palmcorder.

2 Connect the DC Cable to the [DC OUT] Jack on the

AC Adaptor.

3 Connect the AC Adaptor and AC Cable.

CGA-DU07

CGA-DU14

CGA-DU21

PUSH

BATT

1 h 30 min.

2 h 15 min. (1 h 35 min.)

2 h 45 min.

4 h 30 min. (3 h 10 min.)

3 h 55 min.

6 h 45 min. (4 h 45 min.)

≥The AC Cable’s outlet plug cannot be pushed fully into the AC

Adaptor Jack. A gap will remain as shown

≥Before connecting or disconnecting the power supply, set the

[OFF/ON/MODE] Switch on the Palmcorder to [OFF] and make sure that [CAMERA/VCR/CARD PB] Lamps are not lit.

≥Battery cannot be charged if DC Cable is connected to AC

Adaptor.

ª Using the Battery

Before use, fully charge the battery.

1 Attach the Battery to AC Adaptor and charge it.

≥Since the Battery will not be charged when the DC Cable is

connected to the AC Adaptor, disconnect it.

≥The [POWER] Lamp and [CHARGE] Lamp lights up, and

charging starts.

≥When the [CHARGE] Lamp goes off, charging is completed.

2 Attach the charged Battery to the Palmcorder.

Disconnecting the Power Source

Set the [OFF/ON/MODE] Switch 1 to [OFF], and while pressing the [PUSH BATT] Button connector upward to disconnect it.

≥When attaching or removing battery, set [OFF/ON/MODE]

Switch to [OFF] and make sure the Operation Mode Lamp is not lit.

≥When the Palmcorder is used for a long period of time, the Camera

body becomes warm, but this is not a malfunction.

≥If the [CHARGE] Lamp does not light up, although the Battery is

attached to the AC Adaptor, detach the Battery and reattach it.

2, slide the Battery or battery-shaped

~~~~~~~~~~~~~~~~~~~~~~

Charging Time and Available Recording Time

A Charging Time B Maximum Continuous Recording Time

≥“2 h 15 min.” indicates 2 hour and 15 minutes. ≥Battery CGA-DU07 is supplied. ≥The hours shown in the table are approximate hours. ≥The numeric characters in parentheses indicate the recording time

when the LCD monitor is used. In actual use, the available recording time may be shorter in some cases.

≥The hours shown in the table are for continuous recording at a

temperature of 68xF (20xC) and humidity of 60%. If the Battery is charged at a higher or lower temperature, the charging time may be longer.

PV-GS50P.book 19 ページ２００３年２月１７日　月曜日　午後６時３０分

Before Use

Lens Cap and Easy-Grip Strap

ª Attach the Lens Cap

To protect the Lens surface, attach the Lens Cap.

1 Pass one end of the Lens Cap Cord through the

attached eye on the Lens Cap. Then pass the other end through the loop made by itself and pull tight.

2 Pass the end of the Lens Cap Cord through the hole

in the Easy-Grip Strap Attachment part and the Lens Cap through the Lens Cap Cord.

≥The removed Lens Cap can be hooked onto the Easy-Grip Strap

1. (When you are not recording, be sure to keep the Lens Cap

attached to the Lens for protection.)

ª Adjust the Easy-Grip Strap

Adjust the length of the Easy-Grip Strap to the size of your hand.

1 Detach the tip of the Easy-Grip Strap and adjust the

length of it.

2 Reattach the tip of the Easy-Grip Strap.

ª To Use as a Free Style Easy-Grip Strap

Using the Easy-Grip Strap as the Free Style Easy-Grip Strap makes it easier to handle and carry the Palmcorder. when used in conbination with the MagicWire Remote Control with Narration Mic.

Open the Lock Cover 2 by holding tabs 3 on both sides.

Keep pressing on the Lock Button 4 and pull it off.

≥Hold the Palmcorder securely. ≥Close the Lock Cover

Slide the pad of the Easy-Grip Strap.

Attach the Easy-Grip Strap around your wrist.

When re-attaching the Grip Belt Attachment to the Palmcorder

2 after pulling off.

1 It is also convenient

1 Push until it locks with a click.

≥To prevent from getting unlocked accidentally, press on 5 and

mount securely.

PV-GS50P.book 20 ページ２００３年２月１７日　月曜日　午後６時３０分

Attaching the Shoulder Strap

We recommend that you attach the Shoulder Strap before going

outdoors to record so as to avoid dropping the Palmcorder.

1 Pass the tip of the Shoulder Strap through the

Shoulder Strap Holders on the Palmcorder and pull the Shoulder Strap.

2 Fold the tips of the Shoulder Strap, pass it through

the Shoulder Strap Length Adjuster, and pull it.

≥Pull it out more than 1 inch (2 cm) 1 from the Shoulder Strap

Length Adjuster so that it cannot slip off.

≥Please perform this step on the other side as well.

~~~~~~~~~~~~~~~~~~~~~~

3, 4

PUSH

R E C

SAVE

Inserting a Cassette

1 Slide the [OPEN/EJECT] Lever toward the front and

EJECT

/OPEN

pull down to open the Cassette Compartment Cover.

2 Insert a Cassette. 3 Close the Cassette Holder by pressing the

[PUSH CLOSE] Button.

4 Close the Cassette Compartment Cover.

≥For other notes, see page 84.

ª Accidental Erasure Prevention

Opening the accidental erasure prevention slider 1 on the cassette (by sliding it in the [SAVE] arrow direction) prevents recording. To enable recording, close the accidental erasure protection slider (by sliding it in the [REC] arrow direction.)

~~~~~~~~~~~~~~~~~~~~~~

Turning on/off the Palmcorder and Selecting Modes

Turn on the power first and then select Modes.

ª How to Turn on the Power 1

Set the [OFF/ON/MODE] Switch to [ON] while

CAMERA VCR

CARD PB

pressing the

≥The [CAMERA] Lamp lights up.

ª How to Switch Modes

Rotate the [OFF/ON/MODE] Switch.

1, 2

≥With each rotation, the Mode switches in the order of Camera

Mode, VCR Mode, and Card Playback Mode.

≥The appropriate Mode Lamp lights up.

ª How to Turn off the Power

Set the [OFF/ON/MODE] Switch to [OFF] while

pressing the

1 Button.

PV-GS50P.book 21 ページ２００３年２月１７日　月曜日　午後６時３０分

Before Use

Using the Viewfinder

Before using the Viewfinder, adjust the field of view so that the displays inside the Viewfinder become clear and easy to read.

1 Pull the Viewfinder. 2 Adjust the Viewfinder by sliding the Eyepiece

Corrector Knob

Using the LCD Monitor

With the LCD Monitor open, you can also record the picture while watching it.

1 Set the [OFF/ON/MODE] Switch to [ON]. 2 Put your finger on the [OPEN 4] Tab 2 on the

underside of the LCD Monitor and pull the LCD Monitor out about 90x in the direction of the arrow.

≥The Viewfinder goes off.

3 Adjust the LCD Monitor angle according to the

desired recording angle.

≥The LCD Monitor can rotate a maximum of 180x 3 from the

vertical position to the upward direction and a maximum of 90x

4 to the downward direction. Forcefully rotating the LCD

monitor beyond these ranges will damage the Palmcorder.

Closing the LCD monitor

Push the LCD Monitor until it is securely locked.

≥Make sure the Card Slot Cover is closed.

ª Adjusting Brightness and Color Level

When [LCD/EVF SET] on the [DISPLAY SETUP] Sub-menu is set to [YES], the following items are displayed:

LCD Brightness [LCD BRIGHTNESS]

Adjusts the brightness of the image on the LCD screen.

LCD Color Level [LCD COLOR LEVEL]

Adjusts the color saturation of the image on the LCD screen.

Brightness of the Viewfinder [EVF BRIGHTNESS]

Adjust the brightness of the image in the Viewfinder.

Press the [PUSH] Dial and select the item you want to adjust.

Rotate the [PUSH] Dial and increase or decrease the number of the vertical bars on the Bar Indication.

≥The Bar Indication has 8 steps. A larger number of vertical

bars indicates stronger brightness or color saturation.

Increasing the Brightness of the Entire LCD Monitor

Set the [LCD MODE] on the [DISPLAY SETUP] Sub-Menu to [BRIGHT].

≥These adjustments do not affect the recorded images.

≥For other notes, see page 95.

3 180x

4 90x

LCD/EVF SET

LCD BRIGHTNESS

LOW||||----HIGH

LCD COLOR LEVEL LOW||||----HIGH

EVF BRIGHTNESS LOW||||----HIGH

PUSH MENU TO RETURN

PV-GS50P.book 22 ページ２００３年２月１７日　月曜日　午後６時３０分

Using the Menu Screen

To facilitate the selection of a desired function or setting, this Palmcorder displays various function settings on menus.

1 Press the [MENU] Button.

≥The Menu corresponding to the Mode selected by using the

[OFF/ON/MODE] Switch

≥When the [CAMERA] Lamp is on, the Camera Function Menu

is displayed.

≥When the [VCR] Lamp is on, the VCR Function Menu is

displayed.

≥When the [CARD PB] Lamp is on, the Card Function Menu is

displayed.

Rotate the [PUSH] Dial to select a desired Sub-Menu.

3 Press the [PUSH] Dial to display the selected

Sub-Menu.

4 Rotate the [PUSH] Dial to select the item to be set. 5 Press the [PUSH] Dial to set the selected item to a

desired Mode.

≥With each press of the [PUSH] Dial, the cursor [1] brings up a

subsequent Mode. Menu items that cannot be used in combination with the selected menu items are displayed in dark blue.

≥While a Menu is displayed, you cannot begin to record or play

back. Menus can be displayed during playback but not during recording.

≥The above operations can be carried out using the Remote

Controller. (l 15)

≥To display the Menu, press the [MENU] Button

Remote Controller.

≥To select items on the Menu, press the [ITEM] Button

on the Remote Controller.

≥To set the mode for the selected items, press the [SET]

7 on the Remote Controller.

Button

To Exit the Menu Screen

Press the [MENU] Button again.

About the Menu Mode Setting

The setting selected on the Menu will be retained even when the Palmcorder is turned off. (But, the setup of [EFFECT2] (l 39) will not be retained.) If, however, the Battery or AC Adaptor is disconnected before turning the Palmcorder off, the selected setting may not be retained.

≥Menu operation flow is shown in this text by >>.

ª File Selection in the Card Playback Mode (l 58)

A File Selection Operation may be necessary during Menu Operations. In this case, carry out the following procedure.

1 Turn the [PUSH] Dial and select a file.

≥The selected file is marked by a frame 8.

2 Press the [PUSH] Dial to confirm the selection of the

file.

≥After the above File Selection Procedure, carry out the various

Menu Operations. (The above procedure will not be repeated in the following instructions.)

2 3 4

CAMERA VCR

CARD PB

CAMERA FUNCTIONS

CAMERA SETUP

DIGITAL EFFECT

CARD SETUP

MULTI-PICTURES

RECORDING SETUP

DISPLAY SETUP

OTHER FUNCTIONS1

OTHER FUNCTIONS2

PUSH MENU TO EXIT

VCR FUNCTIONS

PLAYBACK FUNCTIONS

DIGITAL EFFECT

CARD SETUP

MULTI-PICTURES

RECORDING SETUP

AV IN/OUT SETUP

DISPLAY SETUP

OTHER FUNCTIONS

PUSH MENU TO EXIT

CARD FUNCTIONS

DELETE CARD FILE

CARD EDITING

DISPLAY SETUP

OTHER FUNCTIONS

PUSH MENU TO EXIT

PHOTO

DATE/

OSD

SHOT

TIME

COUNTER

TITLE

RESET

MULTI/

A.DUB

¥REC

P-IN-P

PLAY

/REW

FF/

615

STILL ADV

PAUSE

STILL ADV

;

STOP

INDEX INDEX

∫

SELECT

VAR.

STORE

OFF/ON

P.B.DIGITAL

PICTURE

No.25 100-0012

2, 3, 4, 5

1, 2

W.B / SHUTTER / IRIS

PUSH

MF / VOL / JOG

START/

STOP

ZOOM

sVOLr

P.B.

ZOOM

SET

ITEM

1 is displayed.

5 on the

PV-GS50P.book 23 ページ２００３年２月１７日　月曜日　午後６時３０分

Before Use

List of Menus

The illustrations of the Menus are for explanation purposes only, and they are different from the actual Menus.

Camera Mode Main-Menu [CAMERA FUNCTIONS]

[CAMERA SETUP] Sub-Menu

1) Auto Exposure Mode [PROG.AE] (l 35)

2) Progressive PhotoShot Mode [PROGRESSIVE] (l 30)

3) Image Stabilizer [EIS] (l 32)

4) Digital Zoom [D.ZOOM] (l 31)

5) Cinema-like Format Recording [CINEMA] (l 33)

6) Self-timer Recording [SELF TIMER] (l 30)

7) Web Camera Mode [WEB CAMERA] (l 71)

8) Returning to the Main-Menu [RETURN]

[DIGITAL EFFECT] Sub-Menu

9) Digital Effects 1 [EFFECT1] (l 39)

10) Digital Effects 2 [EFFECT2] (l 39)

10)

CAMERA SETUP

PROG.AE OFF 5 7 4 Ω º PROGRESSIVE AUTO ON OFF EIS OFF ON D.ZOOM OFF 25k 700k CINEMA OFF ON SELF TIMER OFF ON WEB CAMERA OFF ON

RETURN ---- YES

PUSH MENU TO EXIT

DIGITAL EFFECT

EFFECT1 OFF MULTI P-IN-P WIPE MIX STROBE GAIN UP TRAIL MOSAIC MIRROR EFFECT2 OFF NEGA SEPIA B/W SOLARI

RETURN ---- YES

PUSH MENU TO EXIT

11)

12)

13)

14)

15)

16)

17)

18)

19)

20)

21)

22)

23)

CARD SETUP

PICTURE QUALITY FINE NORMAL ECONOMY MPEG4 MODE SUPERFINE FINE NORMAL BURST MODE OFF H L CREATE TITLE ---- YES

RETURN ---- YES

PUSH MENU TO EXIT

MULTI-PICTURES

SCAN MODE STROBE MANUAL SPEED FAST NORMAL SLOW SWING OFF ON P-IN-P 1 2 3 4

RETURN ---- YES

PUSH MENU TO EXIT

RECORDING SETUP

REC SPEED SP LP AUDIO REC 12bit 16bit SCENE INDEX 2HOUR DAY WIND CUT OFF ON ZOOM MIC OFF ON

RETURN ---- YES

PUSH MENU TO EXIT

[CARD SETUP] Sub-Menu

11) Picture Quality [PICTURE QUALITY] (l 53)

12) MPEG4 Picture Quality [MPEG4 MODE] (l 55)

13) RapidFire

Consecutive Still Shots [BURST MODE] (l 53)

14) Title Creation [CREATE TITLE] (l 61)

[MULTI-PICTURES] Sub-Menu

15) Multi-Picture Mode [SCAN MODE] (l 41)

16) Strobe Multi-Picture Speed [SPEED] (l 41)

17) Swing Mode [SWING] (l 41)

18) Position of Small Picture inside Normal Picture [P-IN-P] (l 40)

[RECORDING SETUP] Sub-Menu

19) Recording Speed Mode [REC SPEED] (l 27)

20) Audio Recording Mode [AUDIO REC] (l 27, 50)

21) Index Mode [SCENE INDEX] (l 46)

22) Wind Noise Reduction [WIND CUT] (l 34) ≥If this function is set to [ON], the sound of wind hitting the

microphone can be reduced for recording.

23) Zoom Microphone [ZOOM MIC] (l 31)

PV-GS50P.book 24 ページ２００３年２月１７日　月曜日　午後６時３０分

[DISPLAY SETUP] Sub-Menu

24)

25)

26)

27)

28)

29)

30)

31)

32)

33)

34)

35)

36)

37)

38)

DISPLAY SETUP

DATE/TIME OFF D/T DATE C.DISPLAY COUNTER MEMORY TIMECODE C.RESET ---- YES DISPLAY ALL PARTIAL OFF LCD MODE NORMAL BRIGHT LCD/EVF SET ---- YES

RETURN ---- YES

PUSH MENU TO EXIT

OTHER FUNCTIONS1

REMOTE VCR1 VCR2 OFF REC LAMP OFF ON BEEP SOUND OFF ON SHTR EFFECT OFF ON CLOCK SET ---- YES SELF REC NORMAL MIRROR VOICE POWER SAVE OFF ON

RETURN ---- YES

PUSH

MENU TO EXIT

OTHER FUNCTIONS2

DEMO MODE OFF ON INITIAL SET

RETURN ---- YES

PUSH

MENU TO EXIT

---- YES

24) Date and Time Indication [DATE/TIME] (l 83)

25) Counter Display Mode [C.DISPLAY] (l 83)

26) Counter Reset [C.RESET] (l 96) ≥Set the counter value to zero. However, it cannot reset the

Time Code.

27) Display Mode [DISPLAY] (l 83)

28) LCD Brightness [LCD MODE] (l 21)

29) LCD and Viewfinder Adjustment [LCD/EVF SET] (l 21)

[OTHER FUNCTIONS1] Sub-Menu

30) Remote Controller Mode [REMOTE] (l 17)

31) Recording Lamp [REC LAMP] (l 28)

32) Beep Sound [BEEP SOUND] (l 84)

33) Shutter Effect [SHTR EFFECT] (l 30)

34) Date and Time Setting [CLOCK SET] (l 27)

35) Self-Recording [SELF REC] (l 29)

36) Voice Power Save [VOICE POWER SAVE] (l 90)

[OTHER FUNCTIONS2] Sub-Menu

37) Demonstration Mode [DEMO MODE] ≥If no operation takes place for approximately 10 minutes after

the AC Adaptor was connected to the Palmcorder and the [OFF/ON/MODE] Switch was turned to [ON] without inserting a Cassette, the Palmcorder is automatically set to Demonstration Mode for introducing its functions. If any button is pressed or operated, the Demonstration Mode is cancelled. The Demonstration Mode can be started by setting [DEMO MODE] to [ON] and by exiting the Menu. To terminate the Demonstration Mode, insert a Cassette or set the [DEMO MODE] to [OFF].

38) Initial Setting Mode [INITIAL SET] (l 83)

PV-GS50P.book 25 ページ２００３年２月１７日　月曜日　午後６時３０分

Before Use

VCR Mode Main-Menu [VCR FUNCTIONS]

PLAYBACK FUNCTIONS

BLANK SEARCH ---- YES

RECORD TO CARD ---- YES SEARCH PHOTO SCENE

bit AUDIO ST1 ST2 MIX

AUDIO OUT STEREO L R

RETURN ---- YES

PUSH MENU TO EXIT

DIGITAL EFFECT

EFFECT OFF ON EFFECT SELECT OFF MULTI WIPE MIX STROBE NEGA SEPIA B/W TRAIL SOLARI MOSAIC MIRROR

RETURN ---- YES

PUSH MENU TO EXIT

CARD SETUP

PICTURE QUALITY FINE NORMAL ECONOMY MPEG4 MODE SUPERFINE FINE NORMAL CREATE TITLE ---- YES

RETURN ---- YES

PUSH MENU TO EXIT

MULTI-PICTURES

SCAN MODE STROBE MANUAL PHOTO SCENE SPEED FAST NORMAL SLOW SWING OFF ON

RETURN ---- YES

PUSH MENU TO EXIT

12)

13)

14)

10)

11)

[PLAYBACK FUNCTIONS] Sub-Menu

1) Blank Search [BLANK SEARCH] (l 45)

2) Recording to Card [RECORD TO CARD] (l 54)

3) Index Search Mode [SEARCH] (l 46)

4) Audio Selector [12bit AUDIO] (l 50)

5) Audio Output Mode [AUDIO OUT] (l 88)

6) Returning to the Main-Menu [RETURN]

[DIGITAL EFFECT] Sub-Menu

7) Digital Effect On/Off [EFFECT] (l 47)

8) Digital Effect Selection [EFFECT SELECT] (l 48)

[CARD SETUP] Sub-Menu

9) Picture Quality [PICTURE QUALITY] (l 53)

10) MPEG4 Picture Quality [MPEG4 MODE] (l 55)

11) Title Creation [CREATE TITLE] (l 61)

[MULTI-PICTURES] Sub-Menu

12) Multi-Picture Mode [SCAN MODE] (l 48)

13) Strobe Multi-Picture Speed [SPEED] (l 48)

14) Swing Mode [SWING] (l 48)

[RECORDING SETUP] Sub-Menu

15)

16)

RECORDING SETUP

REC SPEED SP LP AUDIO REC 12bit

16bit

15) Recording Speed Mode [REC SPEED] (l 27)

16) Audio Recording Mode [AUDIO REC] (l 27, 50)

RETURN ---- YES

PUSH MENU TO EXIT

AV IN/OUT SETUP

AV JACK

17)

IN/OUT OUT/PHONES A.DUB INPUT MIC AV IN

18)

DV OUT OFF ON

19)

RETURN ---- YES

PUSH MENU TO EXIT

DISPLAY SETUP

DATE/TIME OFF D/T DATE C.DISPLAY COUNTER MEMORY TIMECODE C.RESET ---- YES DISPLAY ALL PARTIAL OFF LCD MODE NORMAL BRIGHT LCD/EVF SET ---- YES

RETURN ---- YES

PUSH MENU TO EXIT

OTHER FUNCTIONS

REMOTE VCR1 VCR2 OFF CLOCK SET ---- YES

RETURN ---- YES

PUSH MENU TO EXIT

[AV IN/OUT SETUP] Sub-Menu

17) AV Jack [AV JACK] (l 50, 66, 88)

18) Audio Dubbing Input [A.DUB INPUT] (l 50)

19) AD Conversion Output [DV OUT] (l 67)

[DISPLAY SETUP] Sub-Menu

≥Same as described on page 24.

[OTHER FUNCTIONS] Sub-Menu

≥Same as described on page 24.

PV-GS50P.book 26 ページ２００３年２月１７日　月曜日　午後６時３０分

Card Playback Mode Main-Menu [CARD FUNCTIONS]

DELETE CARD FILE

DELETE FILE

BY SELECTION

DELETE ALL FILES

DELETE TITLE

BY SELECTION

RETURN ---- YES

PUSH MENU TO EXIT

CARD EDITING

RECORD TO TAPE ---- YES FILE SEARCH ---- YES FILE LOCK ---- YES SLIDE SHOW ---- YES DPOF SETTING ---- YES CARD FORMAT ---- YES

RETURN ---- YES

PUSH MENU TO EXIT

[DELETE CARD FILE] Sub-Menu

1) Selecting and deleting a File [DELETE FILE BY SELECTION]

(l 64)

2) Deleting All Files [DELETE ALL FILES] (l 64)

3) Selecting and Deleting a Title [DELETE TITLE BY SELECTION]

(l 64)

[CARD EDITING] Sub-Menu

4) Recording to Cassette [RECORD TO TAPE] (l 59)

5) Searching a File [FILE SEARCH] (l 58)

6) Setting the Lock [FILE LOCK] (l 63)

7) Setting a Slide Show [SLIDE SHOW] (l 60)

8) Setting DPOF [DPOF SETTING] (l 65)

DISPLAY SETUP

DATE/TIME OFF D/T DATE C.DISPLAY COUNTER MEMORY TIMECODE C.RESET ---- YES DISPLAY ALL PARTIAL OFF LCD MODE NORMAL BRIGHT LCD/EVF SET ---- YES

RETURN ---- YES

PUSH MENU TO EXIT

9) Formatting a Card [CARD FORMAT] (l 65)

[DISPLAY SETUP] Sub-Menu

≥Same as described on page 24.

OTHER FUNCTIONS

REMOTE VCR1 VCR2 OFF CLOCK SET ---- YES VOICE POWER SAVE OFF ON

RETURN ---- YES

PUSH MENU TO EXIT

10)

FILE SEARCH

11)

DELETE FILE FILE LOCK

12)

DPOF SETTING EXIT

13)

14)

[OTHER FUNCTIONS] Sub-Menu

≥Same as described on page 24.

Short-Cut Menus of the Card Playback Mode

If you use the Short-Cut Menu, the Card Playback Mode Menu can be called up quickly. Press the [PUSH] Dial to display the Short-Cut Menu, and turn the [PUSH] Dial to select the desired Menu.

10) [FILE SEARCH]:

The [FILE SEARCH] Menu for finding files by number appears.

(l 58)

11) [DELETE FILE]: The [DELETE FILE] Menu for deleting the file being displayed appears. (l 64) Use this Menu after the file to be erased appears.

12) [FILE LOCK]: The [FILE LOCK] Menu to prevent the accidental erasure of files (Lock Setting) being displayed appears. (l 63) Use this Menu after the file to be locked appears.

13) [DPOF SETTING]: The [DPOF SETTING] Menu for performing the DPOF settings for the displayed picture appears. (l 65) Use this Menu after the picture whose DPOF settings are to be performed has appeared.

14) [EXIT]: For terminating the Short-Cut Menu.

PV-GS50P.book 27 ページ２００３年２月１７日　月曜日　午後６時３０分

Before Use

CLOCK SET

YEAR :2003

MONTH :OCT DAY :20 HOUR : 8PM MINUTE:46

PUSH MENU TO RETURN

1, 3 1, 2

W.B / SHUTTER / IRIS

PUSH

MF / VOL / JOG

Setting Date and Time

1 Press the [MENU] Button and rotate the [PUSH] Dial

to select [OTHER FUNCTIONS] >> [CLOCK SET] >> [YES].

2 Rotate and press the [PUSH] Dial to select [YEAR]/

[MONTH]/[DAY]/[HOUR]/[MINUTE] and set it to a desired value.

≥Year will cycle in the order shown below.

2000 ) 2001 ) ... ) 2089 ) 2000 ) ...

3 Press the [MENU] Button to finish setting the date

and time.

≥The clock operation starts from [00] seconds. ≥The menu will disappear when the [MENU] Button is pressed

again.

≥It is possible that the built-in clock in the Palmcorder may become

inaccurate. Please check the time before recording. If the [0] Indication is flashing, charge the built-in lithium battery and reset the date and time.

~~~~~~~~~~~~~~~~~~~~~~

Internal Lithium Battery Recharge

The internal lithium battery sustains the operation of the clock. When the [0] Indication already discharged.

1 Connect the AC Adaptor to the Palmcorder with the

power turned off and then connect to the AC Jack.

≥After charging for 4 hours, the built-in lithium battery can power

the clock for approximately 3 months.

1 is lit, the internal lithium battery is almost or

RECORDING SETUP

REC SPEED

AUDIO REC 12bit SCENE INDEX 2HOUR WIND CUT OFF ZOOM MIC

RETURN ---- YES

PUSH MENU TO EXIT

RECORDING SETUP

REC SPEED

AUDIO REC

SCENE INDEX 2HOUR WIND CUT OFF ZOOM MIC

RETURN ---- YES

PUSH MENU TO EXIT

SP LP

SP 12bit 16bit

~~~~~~~~~~~~~~~~~~~~~~

LP Mode

A desired recording speed can be selected with [REC SPEED] on the [RECORDING SETUP] Sub-Menu.

If LP Mode is selected, the recording time becomes 1.5 times longer than that of SP Mode.

Although the image quality does not decrease with the LP Mode recording, mosaic-like noise patterns may appear on a playback image, or some normal functions may be restricted. ≥The contents that are recorded in LP Mode are not completely

compatible with other equipment.

≥Audio Dubbing is not possible with LP Mode. (l 50)

~~~~~~~~~~~~~~~~~~~~~~

Audio Recording Mode

The sound quality of the recorded sound can be selected with [AUDIO REC] on the [RECORDING SETUP] Sub-Menu. High sound-quality recording is possible with “16bit 48kHz 2 track” Mode. With the “12bit 32kHz 4 track” Mode, the original sound can be recorded on 2 tracks in stereo, while the other 2 tracks can be used for re-recording.

PV-GS50P.book 28 ページ２００３年２月１７日　月曜日　午後６時３０分

CAMERA Mode

CARD

TAPE

MODE

REC

PAUSE

Recording

1 Set the [OFF/ON/MODE] Switch to [ON].

≥The [CAMERA] Lamp lights up. 1

Slide the [TAPE/CARD/CARD MODE] Selector

towards [TAPE].

3 Press the Recording Start/Stop Button.

≥Recording starts. ≥After the [RECORD] indicator is displayed, it changes to

[REC].

≥The Rec Lamp (LED Lamp) 3 lights up during recording and

4 Press the Recording Start/Stop Button again to

pause the recording.

≥[PAUSE] is displayed. 4 ≥If the Recording Pause Mode continues for more than

≥When recording while the Mode Selector Switch is set to [AUTO]

5, the Palmcorder automatically adjusts the focus and white

balance. (In some cases, they cannot be adjusted automatically and need to be adjusted manually.) (l 37)

≥Before turning on the power, remove the Lens Cap. If the Lens

Cap is still attached when the power is turned on, Automatic White Balance Adjustment may not function correctly. (l 37)

ª To Check the Recording

By pressing the [S] Button 6 in the Recording Pause Mode, you can play back the last few seconds of the recorded scene. ≥[CHK]

Recording Pause Mode.

≥For other notes, see page 84.

ª To View the recorded scene while the Recording

is paused

The recorded scene can be viewed by holding down the [SEARCHj] Button Pause Mode. The Camera Search Function is useful for finding the starting point of a new scene to create a smooth transition from one scene to another. ≥When the [SEARCHj] Button is pressed, images are played back

in the reverse direction.

≥When the [SEARCHi] Button is pressed, images are played back

in the forward direction.

≥For other notes, see page 85.

ª To Finish the Recording

Set the [OFF/ON/MODE] Switch to [OFF].

alerts those being recorded that recording is in progress. The Rec Lamp does not light up if the [REC LAMP] on the [OTHER FUNCTIONS1] Sub-menu is set to [OFF].

5 minutes, the power is turned off automatically for tape protection and power conservation. To resume recording from this condition, turn on the power again.

is displayed. After checking, the Palmcorder resumes the

(Camera Search)

6 or [SEARCHi] Button 7 in the Recording

3, 4

AUTO MANUAL FOCUS

CAMERA VCR

CARD PB

RECORD

PAUSE

PV-GS50P.book 29 ページ２００３年２月１７日　月曜日　午後６時３０分

CAMERA

ª To add a Sound while Recording

REC

With the supplied MagicWire Remote Control with Narration Mic connected to the [REMOTE] Jack, you can add a narration while recording is in progress.

While the [TALK] Button

2 is pressed, the [ ] Indication is

displayed and the sound is recorded from [MIC] ≥While the [TALK] Button is pressed, the built-in microphone does

not operate.

ª Self-Recording

By opening the LCD Monitor and turning it so that it faces forward (to the lens side), you can let the subject in front of the Palmcorder monitor the shot while shooting is in progress. ≥When the LCD Monitor is opened, the Viewfinder is disabled

automatically. However, when the LCD Monitor is rotated forward, the image is also shown in the Viewfinder.

≥If you prefer to have the image on the LCD Monitor to look like an

image in a mirror, set [SELF REC] on the [OTHER FUNCTIONS1] Sub-Menu to [MIRROR]. (Mirror Mode) Images are recorded normally and no left and right reversal occurs.

≥If [MIRROR] is used during self-recording, only the basic

indications, such as the Recording Indication [ ] (Red) or [¥], Recording Pause Indication [ ] (Cyan) or [¥;] and Remaining Battery Power Indication [x], are displayed.

≥If a general Warning/Alarm Indication [°] appears, return the LCD

Monitor to the original position in order to check the specific content of the Warning/Alarm Indication.

QUICK

START

~~~~~~~~~~~~~~~~~~~~~~

Quick Start

When this feature is activated, you can resume recording quickly even if the Palmcorder goes into standby mode (when left in Pause mode for 5 minutes). Palmcorder will be ready for shooting in approximately 1.3 seconds when the Power switch is turned [OFF] and back to [ON] again. To activate this feature, press the [QUICK START] button to turn on the Quick Start Lamp.

2, 3

1 Press the [QUICK START] Button.

≥The Quick Start Recording Lamp lights up.

2 Set the [OFF/ON/MODE] Selector to [OFF].

≥The Quick Start Recording Lamp remains lit.

3 Set the [OFF/ON/MODE] Selector to [ON].

≥The Palmcorder will be ready for recording in approximately

1.3 seconds.

≥For other notes, see page 85.

PV-GS50P.book 30 ページ２００３年２月１７日　月曜日　午後６時３０分

Self-timer Recording

W.B / SHUTTER / IRIS

MF / VOL / JOG

PHOTO SHOT

PUSH

When you set the self-timer, the still pictures are automatically taken after 10 seconds, on the Cassette and the Memory Card.

1 Set [CAMERA FUNCTIONS] >> [CAMERA SETUP] >>

[SELF TIMER] >> [ON].

≥The [ ] Indication appears.

2 Press the [PHOTO SHOT] Button.

≥The Recording Lamp and the [ ] Indication flash and the

Photoshot is activated after 10 seconds.

≥

You can also use the RapidFireTM Consecutive Still Shots.

≥For other notes, see page 85.

~~~~~~~~~~~~~~~~~~~~~~

PhotoShot Recording on the DV Cassette

With this function, you can record still pictures with sound for approximately 7 seconds each on the Cassette.

1 Slide the [TAPE/CARD/CARD MODE] Selector to

[TAPE].

CARD

TAPE

PHOTO

MODE

PHOTO

PHOTO SHOT

STILL

2 Press the [PHOTO SHOT] Button in the Recording

Pause Mode.

≥The Palmcorder records a still picture for about 7 seconds and

then switches back to the Recording Pause Mode.

≥PhotoShot Recording results in slightly inferior image quality. ≥If you set [SHTR EFFECT] on the [OTHER FUNCTIONS1]

Sub-Menu to [ON], you can add an image and a sound like releasing the shutter.

ª Progressive PhotoShot

With the Progressive PhotoShotTM Mode, you can record still pictures with higher resolution than with the normal PhotoShot Function. ≥After setting [PROGRESSIVE] on the [CAMERA SETUP]

Sub-menu to [ON] or [AUTO], press the [PHOTO SHOT] Button in the Recording Pause Mode. [æ] is displayed.

≥This Function may not work with some function settings. (l 85) ≥If you select Card Mode, [PROGRESSIVE] is set to [ON].

ª Continuous PhotoShot

If the [PHOTO SHOT] Button is held down with the [SHTR EFFECT] of the Sub-Menu [OTHER FUNCTIONS1] set to [ON], the Palmcorder will record still images without interruptions every

0.7 seconds until the button is released.

≥The screen blinks and, at the same time, a shutter clicking sound is

recorded. (This function, however, is not enabled when Progressive PhotoShot is set to [ON] or [AUTO].)

ª Digital Still Picture

When the [STILL] Button 2 is pressed, images become still pictures. When the Button is pressed again, the Digital Still Picture Mode is cancelled. ≥We recommend that you press the [STILL] Button first at the

position where you want to record the picture and then press the [PHOTO SHOT] Button.

≥For other notes, see page 85.

Mode

+ 190 hidden pages