Panasonic PV-DV202, PV-DV402 Operating Instruction
R
Digital Video Camcorder
Operating Instructions
[ PV-DV402 shown ]
Models No.
PV-DV202
PV-DV402
Mini
Before attempting to connect, operate or adjust this product, please read these
instructions thoroughly.
Spanish Quick Use Guide is included.
Guía para rápida consulta en español está incluida.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
LSQT0563A
Things You Should Know
Thank you for choosing Panasonic!
You have purchased one of the most
sophisticated and reliable products on the
market today. Used properly, we’re sure it
will bring you and your family years of
enjoyment. Please take time to fill in the
information below. The serial number is on
the tag located on the underside of your
Palmcorder. Be sure to retain this manual
as your convenient Palmcorder information
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.
source.
Safety Precautions
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
Mini
Your
and Long (LP) mode.
It is recommended that only cassette tapes that have been tested and inspected for use in
VCR machines with the
Note: This equipment has been tested and found to comply with Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful
interference when operated in a residential environment.
If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, use the equipment in another location
and/or utilize an electrical outlet different from that used by the receiver.
If necessary, consult the dealer or an experienced radio/TV technician for help. You may
find the booklet, ‘Something About Interference’ available from FCC local regional offices
helpful.
FCC Warning: To assure continued FCC compliance, use only the provided shielded
2
Palmcorder is designed to record and play back in Standard Play (SP) mode
Mini
mark be used.
This symbol warns the user that uninsulated
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
voltage within the unit may have sufficient
magnitude to cause electric shock.
Therefore, it is dangerous to make any kind
of contact with any inside part of this unit.
This symbol alerts the user that important
literature concerning the operation and
maintenance of this unit has been included.
Therefore, it should be read carefully in order
to avoid any problems.
The above markings are located on the appliance bottom cover.
Model Number : PV-DV202/PV-DV402
Trade Name : Panasonic
Responsibility Party : Matsushita Electric Corporation of America
Address : One Panasonic Way Secaucus New Jersey 07094
Telephone Number : 1-800-211-PANA(7262)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
interface cable when connecting digital video camcorder to computer in
accordance with instruction herein. Also, any unauthorized changes or
modifications to this equipment would void the user’s authority to operate.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Declaration of Conformity
Important Safeguards
1. Read Instructions — All the safety and operating
instructions should be read before the unit is
operated.
2. Retain Instructions — The safety and operating
instructions should be retained for future reference.
3. Heed Warnings — All warnings on the unit and in the
operating instructions should be adhered to.
4. Follow Instructions — All operating and maintenance
instructions should be followed.
5. Cleaning — Unplug this video unit from the wall outlet
before cleaning. Do not use liquid or aerosol
cleaners. Use a dry cloth for cleaning.
6. Attachments — Do not use attachments not
recommended by the video product manufacturer as
they may be hazardous.
7. Water and Moisture — Do not use this video unit near
water — for example near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet basement, or
near a swimming pool, and the like.
8. Accessories — Do not place this video unit on an
unstable cart, stand, tripod, bracket, or table. The
video unit may fall, causing serious injury to a child or
adult, and serious damage to the unit. Use only with
a cart, stand, tripod, bracket, or table recommended
by the manufacturer, or sold with the video unit. Any
mounting of the unit should follow the manufacturer’s
instructions and should use a
mounting accessory
recommended by the
manufacturer. An appliance and
cart combination should be moved
with care. Quick stops, excessive
force, and uneven surfaces may
cause the appliance and cart
combination to overturn.
9. Ventilation — Slots and openings in the cabinet are
provided for ventilation and to ensure reliable
operation of the video unit and to protect it from
overheating. These openings must not be blocked or
covered. Never place the video unit on a bed, sofa,
rug, or other similar surface, or near or over a radiator
or heat register. This video unit should not be placed
in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
10. Power Sources — This video unit should be operated
only from the type of power source indicated on the
marking label. If you are not sure of the type of power
supply to your home, consult your appliance dealer
or local power company. For video units intended to
be operated from battery power, or other sources,
refer to the operating instructions.
11. Grounding or Polarization — This video unit may be
equipped with either a polarized 2-wire AC
(Alternating Current) line plug (a plug having one
blade wider than the other) or 3-wire grounding type
plug, a plug having a third (grounding) pin.
The 2-wire polarized plug will fit into the power outlet
only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try
reversing the plug. If the plug still fails to fit, contact
your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug.
The 3-wire grounding type plug will fit into a
grounding type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
grounding type plug.
12. Power-Cord Protection — Power-supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them, paying particular attention to cords of
plugs, convenience receptacles, and the point
where they exit from the unit.
13. Outdoor Antenna Grounding — If an outside
antenna or cable system is connected to the video
unit, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges. Part 1 of
the Canadian Electrical Code, in USA Section 810
of the National Electrical Code, provides information
with respect to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes, and
requirements for the grounding electrode.
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
ELECTRIC
SERVICE
EQUIPMENT
-
NEC
NATIONAL ELECTRICAL CODE
14. Lightning — For added protection of this video unit
receiver during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage
to the video unit due to lightning and power-line
surges.
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
Before Use
3
Important Safeguards
15. Power Lines — An outside antenna system should
not be located in the vicinity of overhead power lines
or other electric light or power circuits, or where it can
fall into such power lines or circuits. When installing
an outside antenna system, extreme care should be
taken to keep from touching such power lines or
circuits as contact with them might be fatal.
16. Overloading — Do not overload wall outlets and
extension cords as this can result in a risk of fire or
electric shock.
17. Objects and Liquids — Never push objects of any
kind into this video unit through openings as they
may touch dangerous voltage points or short out
parts that could result in a fire or electric shock.
Never spill liquid of any kind onto the video unit.
18. Servicing — Do not attempt to service this video unit
yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
19. Damage Requiring Service — Unplug this video unit
from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If any liquid has been spilled into, or objects have
fallen onto, the video unit.
c. If the video unit has been exposed to rain or water.
d. If the video unit does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician to
restore the video unit to its normal operation.
e. If the video unit has been dropped or the cabinet
has been damaged.
f. When the video unit exhibits a distinct change in
performance — this indicates a need for service.
20. Replacement Parts — When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock or other hazards.
21. Safety Check— Upon completion of any service or
repairs to this video unit, ask the service technician to
perform safety checks to determine that the video
unit is in safe operating order.
Precautions
USE & LOCATION
TO AVOID SHOCK HAZARD ... Your Palmcorder and power supply should not be exposed to rain or moisture. Do
not connect the power supply or operate your Palmcorder if it gets wet. Your Palmcorder has been designed for
outdoor use, however it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or direct
splashing from a pool or even a cup of coffee. This action could permanently damage the internal parts of your
Palmcorder. Do not attempt to disassemble this unit. There are no user serviceable parts inside. Unplug your
Palmcorder from the power supply before cleaning.
DO NOT AIM YOUR PALMCORDER AT THE SUN OR OTHER BRIGHT OBJECTS
DO NOT LEAVE THE PALMCORDER WITH THE EVF AIMED DIRECTLY AT THE SUN AS THIS MAY CAUSE
DAMAGE TO THE INTERNAL PARTS OF THE EVF
DO NOT EXPOSE YOUR PALMCORDER TO EXTENDED HIGH TEMPERATURE ... Such as, direct sunlight,
inside a closed car, next to a heater, etc... This action could permanently damage the internal parts of your
Palmcorder.
AVOID SUDDEN CHANGES IN TEMPERATURE ... If the unit is suddenly moved from a cold place to a warm
place, moisture may form on the tape and inside the unit.
DO NOT LEAVE YOUR PALMCORDER OR THE POWER SUPPLY TURNED ON WHEN NOT IN USE.
STORAGE OF YOUR PALMCORDER ... Store and handle your Palmcorder in a manner that will not subject it to
unnecessary movement (avoid shaking and striking). Your Palmcorder contains a sensitive pick-up device which
could be damaged by improper handling or storage.
CARE
TO CLEAN YOUR PALMCORDER ... Do not use strong or abrasive detergents when cleaning your Palmcorder
body.
TO PROTECT THE LENS ... Do not touch the surface of the lens with your hand. Use a commercial Palmcorder
lens solution and lens paper when cleaning the lens. Improper cleaning can scratch the lens coating.
TO PROTECT THE FINISH OF YOUR PALMCORDER ... Before handling your Palmcorder, make sure your hands
and face are free from any chemical products, such as suntan lotion, as it may damage the finish.
4
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Table of Contents
Things You Should Know................................................................................................ 2
Important Safeguards ..................................................................................................... 3
Precautions .....................................................................................................................4
Before Using ....................................................................................................................6
• Easy Cassette Eject..................................................................................................... 7
Quick Guide ................................................................................................................... 11
Supplying Power ...........................................................................................................14
Setting the Clock ...........................................................................................................16
Using the Palmcorder Menu......................................................................................... 17
Before Use
Camera Recording ........................................................................................................ 18
• Simple Recording .................................................................................................. 18
• Digital PhotoShot™ Mode ..................................................................................... 20
• Zoom ..................................................................................................................... 21
Special Effect Features................................................................................................. 23
Advanced Settings ........................................................................................................ 28
Playback Y our Recordings ........................................................................................... 32
Special Effect Features................................................................................................. 34
Digital Features.................................................................................................................40
Editing Features ............................................................................................................... 44
Card Features.................................................................................................................... 48
PC Connection
• T ransf erring Your Images (Windows) ......................................................................... 55
• PHOT OVU/MPEG4 Movie Messenger™ System...................................................... 58
• T ransferring Y our Images (i.LINK) (Windows) ............................................................ 72
• PHOTO VU/MPEG4 Movie Messenger™ System (i.LINK) ......................................... 73
• Palmcorder USB Device Driver/SD Dri ve................................................................... 75
• Palmcorder File Conv erter......................................................................................... 78
• Web Camera (For Windows XP users/F or Windows 98SE, Me, 2000 users) ............. 80
• Warning Indications...................................................................................................89
PC Connection
• T ransf erring Your Images (Macintosh)........................................................................ 90
Palmcorder Accessory System ................................................................................... 92
Palmcorder Accessory Order Form ............................................................................ 93
Notes On Operations ....................................................................................................94
Specifications................................................................................................................96
Before Requesting Service .......................................................................................... 97
On-Screen Display (OSD) ............................................................................................. 99
Request for Service Notice ........................................................................................ 101
Limited Warranty ......................................................................................................... 102
Servicenter List ........................................................................................................... 103
Spanish Quick Use Guide/Guía Para Uso Rápido ....................................................104
MENU OSD................................................................................................................... 108
Electronic Viewfinder/LCD Monitor Indications........................................................ 112
Index of Controls.........................................................................................................116
Index............................................................................................................................. 119
Camera VCR
Special Features
For Y our Information
5
Before Using
This Operating Instructions book is designed for use with models PV-DV202 and
PV-DV402. The PV-DV402 is the model used for illustrative purposes.
Features may vary, so please read carefully.
Differences between models
Model Number
LCD Monitor
MagicVu™ IR
Filter (0Lux)
MIC IN
EXTERNAL
63.5 mm (2.5 inch) Liquid
Crystal Display
Unpack your Palmcorder
1 pc. AC Adaptor
(PV-DAC11) with
AC Cable and DC
Cable
PV-DV202
NO
NO
1 pc. 8 MB Memory
Card
(RP-SD008BMKO)
88.9 mm (3.5 inch) Liquid
Crystal Display
1 pc. Battery Pack
(CGR-D08/
CGR-D08R)
PV-DV402
YES
YES
1 pc. A/V Cable
(LSJA0280)
1 pc. Lens Cap
(LSYF0518) with
Lens Cap Strap
(LSGQ0066)
1 pc. IR Remote
Control (LSSQ0294)
with Battery (CR2025)
Microsoft®, Windows® and Windows Media are registered trademarks of Microsoft in the
United States and other countries.
Macintosh, iMac, iBook, PowerBook, Power Macintosh, Power Mac, and Mac are
trademarks or registered trademarks of Apple Computer, Inc.
®
Intel
Pentium® is a registered trademark.
i.LINK is a trademark.
PHOTOVU/MPEG4 Movie Messenger™ System is a registered trademark.
IBM is a registered trademark of IBM Company.
MultiMediaCard is a registered trademark.
SD is a trademark.
6
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
1 pc. USB Cable
(K1HA05CD0001)
1 pc. CD-ROM of Driver Software for Windows 98SE/Me/2000/XP
and Macintosh; USB Device Driver for Windows 98SE/Me/2000/
XP; PHOTOVU/MPEG4 Movie Messenger™ System for Windows
98SE/Me/2000/XP; Built-in SD Drive for Macintosh; ArcSoft
Software for Windows 95/98/Me/2000/XP and Macintosh
(LSFT0492)
1 pc. Shoulder
Strap (LSFC0016)
1 pc. Audio Adaptor
(LSJP0829)
Before Using
Record Speed/Playback Time
Use only those tapes having the
logo indicating the 6.35 mm digital
standard.
Record Speed/
Cassette type
AY-DVM30EA
AY-DVM60EA
AY-DVM80EA 80 minutes 120 minutes
Playback time
SP
30 minutes
60 minutes
Mini
LP
45 minutes
90 minutes
Easy Cassette Eject/Insertion
• If the Palmcorder is connected to a power
source, the cassette can be inserted and
ejected without turning the Palmcorder
on.
4
PUSH TO
CLOSE
2
TAPE EJECT
Erase Protection
Cassettes have a sliding record tab to
ensure recordings are not accidentally
erased.
1
To prevent accidental erasure:
Slide the tab to the left (open).
2
To record again:
Slide the tab to the right (close).
record tab
Before you begin
• Connect the Palmcorder to a power
source. (pp. 14, 15)
1
Press LCD-OPEN to unlock the LCD
monitor, and swing it fully open.
2
Slide TAPE EJECT to open the
Cassette Compartment Cover.
Before Use
3
Insert a cassette record tab up,
1
LCD-OPEN
Cassette Compartment
Cover
window side facing out.
4
Press PUSH TO CLOSE to close the
Cassette Compartment Cover.
•To remove the cassette...
Slide TAPE EJECT to open the Cassette
Compartment Cover and pull the cassette
tape straight out.
Note
• When inser ting the cassette, make sure it is facing the right direction and then push it
in completely.
7
Before Using
Attaching the Shoulder Strap
1
Undo the two strap ends from their
buckles.
2
Thread the strap ends through the
Strap Attachment Rings.
3
Reinsert the strap ends through their
buckles.
• Make sure the straps are not twisted.
2
3
Hand Strap
Adjust the length of the Hand Strap to the
size of your hand as illustrated.
Adjust the Length
1
Loosen the strap from the Buckle and
create a loop.
2
Pull the strap firmly through the
Buckle to shorten or lengthen the
strap.
1
Lens Cap
Attaching the Lens Cap Strap:
Thread the Lens Cap Strap through the
Strap Attachment Ring as shown.
1
OR
2
1
Hand Strap
8
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
3
Attaching the Lens Cap Cord to the Hand
Strap:
Remove the Hand Strap from the front
clasp and thread the Strap through the loop
in the Lens Cap Cord.
Reattach the Hand Strap.
Before Using
Using the Built-in Light
To brighten the natural colors in a scene.
Built-in Light
Before you begin
• Connect the Palmcorder to a power
source. (pp. 14, 15)
• Set POWER to CAMERA or M-CARD.
1
Hold down LIGHT for more than 0.7
seconds to turn ON or OFF.
•“
” will appear on the screen.
Note
• Using Light reduces batter y time.
• Provide adequate ventilation if using
Light in a hot environment for a long time.
• Set LIGHT to OFF when not in use.
• When replacing the bulb, see page 94.
Caution
This light becomes hot during operation.
Make sure nothing covers the light during
operation.
1
LIGHT
Remote Control
You can operate the major functions of your Palmcorder from up to approximately 5 m
(16 feet) away (indoors). Aim the IR Remote Control toward the front of the Palmcorder
and press the desired buttons (Remote Sensor is located under the lens).
To operate Camera functions:
Set POWER to CAMERA.
Before Use
○○○○
Remote Sensor
Controlled Functions
• Rec/Pause (p. 18)
• Tele (Zoom) (p. 21)
• Wide (Zoom) (p. 21)
• Date/Time (p. 112)
• Reset (p. 45)
• PhotoShot (p. 20)
• Display On TV (p. 39)
• Counter/Time Code (p. 113)
• Audio Dubbing (p. 44)
• Record (p. 47)
• Menu (p. 17)
• Play (p. 32)
To operate VCR functions:
Set POWER to VCR.
• FF/Search (p. 34)
• REW/Search (p. 34)
• Pause/Select (pp. 16, 17, 36)
• Stop/Set (pp. 16, 17, 32, 47)
• Slow/Frame Advance (Forward)
(pp. 35, 36)
• Slow/Frame Advance (Backward)
(pp. 35, 36)
• Index Search (Forward) (pp. 36, 37)
• Index Search (Backward) (pp. 36, 37)
• Speaker Volume (p. 33)
9
Before Using
Replace the Battery
B
1
While pressing the tab in the direction of the arrow (A) with
A
+
Replace battery with Panasonic PART NO. VSBW0004 (CR2025) only. Use of another battery may
present a risk of fire or explosion.
Caution: battery may explode if mistreated. Dispose of used battery properly. Keep away from
children. Do not recharge, disassemble or dispose of in a fire.
Remote Controlling Two
Palmcorders
You can control any two Panasonic
Palmcorders with one Remote control. In
order for the remote to distinguish between
the two units, it is necessary to set one of
the Palmcorders to VCR 2. On the remote,
press VCR 1 or VCR 2 to control the
desired Palmcorder.
For VCR 2 :
Press these
buttons at the
same time.
Note
• When the Palmcorder and remote are
not set to the same mode (VCR1 or
VCR2), “CHECK REMOTE MODE
(REMOTE)” will appear.
your fingernail, pull out the Battery Tray (B).
2
Insert the battery into the Battery Tray with the + mark
facing up.
Do not reverse the polarity.
3
Insert the Battery Tray.
1
Set POWER to VCR or CAMERA.
• The POWER Lamp lights red.
• Be sure POWER is fully turned to
VCR or CAMERA position.
2
Press MENU to display the VCR or
CAMERA mode menu screen.
3
Rotate JOG KEY to select SET-UP in
the CAMERA mode menu screen or
PLAY MODE in the VCR mode menu
screen, then press JOG KEY to
display the CAMERA SET-UP or VCR
For VCR 1 :
Press these
buttons at the
same time.
PLAY MODE menu screen.
4
Rotate JOG KEY to select REMOTE ,
and then press JOG KEY to select
VCR 2 (Menu OSD: pp. 109, 110).
Leave the other Palmcorder set to
VCR1.
5
Set the Remote Control to VCR 1 or
VCR 2 to correspond with the
Palmcorder you wish to control. (See
above left.)
• After replacing the Remote Control
Battery, the remote will default to VCR 1.
10
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Quick Guide
Insert the Battery Pack
Protection Film
Note
• Remove the
Protection Film before use.
1
Insert Cassette
These Palmcorders are equipped with the Easy Cassette Eject System so
it is easy to insert or remove tapes, even when on a tripod. (p. 7)
1
Press LCD-OPEN to unlock the LCD
monitor, and swing it fully open.
Before you begin
• Charge the Battery. (p. 14)
12
Insert the Battery Pack and slide
it up until it locks with a click.
2
Set POWER to VCR or
CAMERA.
Before Use
5
Press PUSH TO CLOSE mark
to close the Cassette
Compartment Cover.
3
Slide TAPE EJECT to open
the Cassette Compartment
Cover.
4
Insert a cassette record tab
up, window side facing out.
• Make sure the record tab
is closed. (p. 7)
11
Quick Guide
Camera Recording
When the LCD monitor is fully open, the
Viewfinder automatically turns OFF.
1
Set POWER to
CAMERA.
4
Press REC/PAUSE to start recording.
Press REC/PAUSE again to pause
recording.
To Watch Playback in the LCD
(Liquid Crystal Display)
When the LCD monitor is fully open, the
Viewfinder automatically turns OFF.
2
Adjust the Vision Adjustment
Control to your eyesight.
180°
90°
LCD Monitor
3
Press LCD-OPEN to unlock
the LCD monitor. Swing it fully
open and adjust the angle.
Before you begin
• Charge the Battery. (p. 14)
Viewfinder
1
180°
90°
2
Press LCD-OPEN to unlock the LCD
monitor. Swing it fully open and
adjust the angle.
3
Press (REW)
to rewind the tape.
12
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Set POWER to VCR.
4
Press (PLAY) to start
playback.
5
Press (STOP) to stop
playback.
Quick Guide
Insert Memory Card*
*Memory Card:MultiMediaCard or SD Memory Card (p. 94)
• Be sure to insert the Memory Card before using the Card PhotoShot. (p. 48)
Below is a list of memory cards which can be used in this Palmcorder.
Memory Card
SD Memory Card (RP-SD008BMKO) (supplied)
MultiMediaCard (SanDisk brand)
SD Memory Card (optional) (p. 92)
SD Memory Card write protection switch
A write protection switch is located on the SD Memory Card. Sliding the
switch to the “LOCK” position prevents writing on or formatting the card.
Write protection Switch
1
Set POWER to OFF.
To remove the Memory Card...
Press here to eject the card.
About the M-CARD Lock
Switch
POWER
Before you begin
• Charge the Battery. (p. 14)
Capacity
8 MB
8 MB, 16 MB
16 MB, 32 MB, 64 MB
2
Slide DOOR OPEN to open
M-CARD door.
3
Insert the Memory Card and hold
in place until you hear a click.
4
Close the M-CARD Door.
When inserting the Memory
Card
Before Use
M-CARD Lock
Note
• By sliding M-CARD Lock to LOCK, you
can prevent POWER from accidentally
entering the M-CARD position when
changing POWER to CAMERA.
Note
• When inserting the Memory Card, insert
with the cropped corner down as shown in
the illustration above.
cropped corner
13
Supplying Power
Charge the Battery Pack on
the AC Adaptor
1
Connect and plug in the Power Cord
as shown.
• POWER Lamp will light.
• Remove the DC Cable, if attached,
from the adaptor.
2
Attach the Battery as shown to
POWER Lamp
CHARGE Lamp
Note
About the Flashing of the CHARGE Lamp
• Charge the Battery within an ambient temperature range of 10 °C (50 °F) and
30 °C (86 °F).
• If charging is done in extreme low or high temperatures, Battery charge time increases.
CHARGE Lamp flashes when...
• The Battery is being charged, but charging is taking longer than normal.
• Charging is not possible. Remove the Battery once, wait a short time, then re-attach it
for charging.
charge.
• CHARGE Lamp lights up. It goes out
when charging is complete (approx.
1 hour). Expect approx. 1 hour
30 minutes of operation (EVF usage)
when fully charged.
3
Remove the Battery.
Slide the Battery out and then lift up.
Insert the Battery Pack
2
1
1
Insert the Battery Pack and slide it up
until it locks with a click.
14
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Remove the Battery Pack
2
BATT RELEASE
1
Tilt Viewfinder upward.
2
Remove the Battery Pack and slide
the Battery downward while sliding the
BATT RELEASE.
3
1
Supplying Power
Battery Care
Caution:
• Charge only with specified charger.
• Charge the Battery within an ambient
temperature range of 10 °C (50 °F) and
30 °C (86 °F).
• The Battery may be warm after charging or just
after use. This is normal.
• Do not use an insufficiently charged or worn out
Battery.
• If charging is done in extreme low or high
temperatures, Battery charge time increases.
Safety precautions:
• Do not place the Battery near, or dispose of in fire.
• Do not directly connect (short circuit) the positive
(+) and negative (–) terminals.
• Never attempt to disassemble or reassemble the
Battery.
U.S.A. CONSUMERS: ATTENTION:
A lithium ion/polymer battery that is recyclable powers the product
you have purchased. Please call 1-800-8-BATTERY for information
on how to recycle this battery.
Use AC Adaptor
3
2
1
BATT RELEASE
DC IN Terminal
To avoid damage to the Battery:
• Do not drop or jar the Battery.
• Use the Battery with specified models only.
• If the Battery is used in extremely high
temperatures, a safety device will automatically
prevent operation.
To insure longer battery life:
• While not in use, remove Battery from the
Palmcorder and AC Adaptor and store in a
cool, dark, dry place. If you leave the Battery in
the Palmcorder or on the AC Adaptor, the Battery
will no longer be rechargeable.
• Keep the Battery terminals clean.
1
Slide the Battery downward while
sliding BATT RELEASE to remove the
Battery Pack. (p. 14)
2
Insert the DC Cable into the DC IN
Terminal.
3
Connect the other end of the DC
Cable to the AC Adaptor as shown.
4
Plug in the AC Adaptor.
• The POWER Lamp on the AC
Adaptor lights up.
Before Use
DC Cable
(Supplied)
1
POWER
Lamp
2
Note
• When not in use, unplug the AC Adaptor
from the AC outlet. (AC Adaptor consumes
1 W of electric power when plugged into
an AC outlet even when not in use.)
DC Output Connector
3
15
Setting the Clock
Set the Date and Time
The date and time is calculated, including
leap year, up to DEC 31 2089.
2, 3, 4
JOG KEY
1
MENU
EXAMPLE:
YEAR
MONTH
MONTH
: 2002
PUSH
: JAN
PUSH
: FEB
Push
Rotate
Before you begin
• Connect the Palmcorder to a power
source. (pp. 14, 15)
• Set POWER to CAMERA or VCR.
1
Press MENU to display the Camera or
VCR mode menu screen.
(p. 17)
[ CAMERA MENU ]
.
2
Rotate JOG KEY to select DISPLAY
SETTING , and then press JOG KEY
to display the DISPLAY SETTING
menu screen.
3
Rotate JOG KEY to select CLOCK-
SET , and then press JOG KEY to set
to ON. (Menu OSD: pp. 109, 111)
• The DATE/TIME SETTING menu
is displayed.
4
Rotate JOG KEY to select YEAR, then
press JOG KEY to fix and move to the
next item. Likewise, set the month,
day, hour, and minutes.
[ VCR MENU ]
Note
• To make corrections,
Press JOG KEY repeatedly to move back
to an item and correct.
• A built-in Battery maintains clock
operation. If the Palmcorder is not
connected to a power source for a few
months, the built-in battery may discharge
and “CLOCK BATTERY” indication
appears. (p. 99)
16
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
When DATE/TIME setting is
completed, press MENU three times to
start the clock and exit.
Using the Palmcorder Menu
The Palmcorder features three menu
displays: one for CAMERA mode
(recording), one for M-CARD (Memory Card
Photo Mode) and one for VCR mode
(Playback). (pp. 108~111)
• While the Menu screen is displayed, you
cannot record on or play a tape.
• While recording, the Menu screen cannot
be displayed.
• During playback, the Menu screen can be
displayed.
Before you begin
• Connect the Palmcorder to a power
source. (pp. 14, 15)
• Set POWER to CAMERA or VCR.
2, A, B, C
JOG KEY
1, D
MENU
CAMERA Main menu
1 : D. FUNCTION
CAMERA FUNCTION menu is
displayed. To select D.FUNCTION,
D.ZOOM, or PROGRESSIVE.
2 : ADJUST
CAMERA ADJUST menu is displayed.
To select PROG. AE or CINEMA.
3 : REC MODE
CAMERA REC-MODE menu is
displayed. To select REC-SPEED,
AUDIO-REC, INDEX, SHUTTER,
SELF-REC, WIND-CUT, or ZOOM-MIC.
4 : SET-UP
CAMERA SET-UP menu is displayed.
To select REMOTE, BEEP, or
MAGICVU (PV-DV402 only).
5 : DISPLAY SETTING
DISPLAY SETTING menu is displayed.
To select DISPLAY, C.RESET, DATE/
TIME, or CLOCK-SET.
6 : LCD/EVF SETTING
LCD/EVF SETTING menu is displayed.
To select LCD BRIGHTNESS, LCD
COLOR or EVF BRIGHTNESS.
7 : PHOTO TITLE
PHOTO TITLE menu is displayed. To
select TITLE or MODE.
Displaying the MENU
1
Press MENU to display the CAMERA
or VCR menu (according to the
POWER setting).
2
Rotate JOG KEY to select a menu
item.
Setting the MENU Items
(EX. VCR Mode menu)
A
Press JOG KEY to set your selection.
B
Rotate JOG KEY to select a menu
item.
C
Press JOG KEY to set your selection.
• The “●” mark indicates selection.
D
Press MENU twice to exit the menu.
VCR Main menu
1 : PLAY FUNCTION
VCR PLAY FUNCTION menu is
displayed. To select D. FUNCTION,
D.EFFECT, or D.ZOOM.
2 : REC MODE
VCR REC MODE menu is displayed.
To select REC-SPEED or AUDIO-DUB.
3 : PLAY MODE
VCR PLAY MODE menu is displayed.
To select INDEX, AUDIO, REMOTE, or
B.SEARCH.
4 : MULTI SETTING
MULTI SETTING menu is displayed.
To select SPEED.
5 : DISPLAY SETTING
DISPLAY SETTING menu is displayed.
To select DISPLAY, C.RESET, DATE/
TIME, or CLOCK-SET.
6 : LCD/EVF SETTING
LCD/EVF SETTING menu is displayed.
To select LCD BRIGHTNESS, LCD
COLOR or EVF BRIGHTNESS.
Before Use
17
Camera Recording
Simple Recording
Remove the lens cap and clip it to the hand
strap.
Clip here
EVF
REC/PAUSE mode
POWER Lamp
1, 5
POWER
2
Vision
Adjustment
Control
3
MENU
4
REC/PAUSE
Before you begin
• Connect the Palmcorder to a power
source. (pp. 14, 15)
• Insert a cassette with the record tab
closed. (p. 7)
1
Set POWER to CAMERA.
• The POWER Lamp lights red.
• Be sure POWER is fully turned to the
CAMERA position.
2
With the Viewfinder Eye Cup held up
against your eye, adjust the Vision
Adjustment Control to your eyesight.
• Adjust the EVF Brightness of the
Viewfinder if necessary.
Please refer to “To adjust the LCD/
EVF BRIGHTNESS or COLOR” on
page 19.
3
Set to REC-SPEED “SP” or “LP” in
the CAMERA Mode Menu.
(Menu OSD: p. 108)
4
Press REC/PAUSE to start recording.
•“REC” is displayed on the screen.
Press REC/PAUSE again to pause
recording.
5
Set POWER to OFF when finished.
• To remove the cassette, slide TAPE
EJECT.
• When the Palmcorder is aimed at
excessively bright objects, or bright lights,
a vertical bar may appear in the picture.
This is a normal characteristic of the CCD
pick-up device. Try to avoid this whenever
possible.
To conserve power
WARNING:
• Do not leave the Palmcorder with the
EVF aimed directly at the sun as this
may cause damage to the internal parts
of the EVF.
• Do not lift, or carry, the Palmcorder
by the EVF or the LCD Monitor.
18
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
After 5 minutes, the Record/Pause mode
will automatically change to Standby
mode.
To resume recording, set POWER to
OFF and then ON again.
Camera Recording
Using the LCD Monitor
The LCD (Liquid Crystal Display) monitor
can be used while recording.
1
LCD-OPEN
180°
90°
90°
To adjust the LCD/EVF
BRIGHTNESS or COLOR
1
Press LCD-OPEN to unlock the LCD
monitor.
2
Swing the LCD monitor fully open
and adjust the viewing angle.
• The LCD monitor will automatically
turn on.
• When the LCD monitor is completely
closed, it will shut off automatically to
save power.
• Adjust the LCD Brightness and/or
color of the LCD monitor if necessary.
Please refer to “To adjust the LCD/
EVF BRIGHTNESS or COLOR”
below.
3
Start recording.
Note
• Using the LCD monitor will reduce battery
operating time.
• Close the LCD monitor completely when
not in use.
1
Press MENU to display the main menu
screen.
Camera
1, 5
MENU
2, 3, 4
JOG KEY
EVF/LCD
2
Rotate JOG KEY to select LCD/EVF
SETTING from the main menu screen.
(Menu OSD: pp. 109, 111)
3
Press JOG KEY to display the LCD/
EVF SETTING screen.
4
Press JOG KEY to select LCD
BRIGHTNESS, LCD COLOR, or
EVF BRIGHTNESS, then rotate JOG
KEY to adjust.
5
Press MENU twice to exit this mode.
19
Camera Recording
Digital PhotoShot™ Mode
Use this feature to record a seven second
(approx.) still image from the current camera
picture. Audio is also recorded for on-thespot narration. Or, you can add narration
later with the Audio Dubbing feature to make
an interesting slide show, etc. (p. 44)
1
POWER
2
PHOTOSHOT
Progressive PhotoShot™
Mode
With the progressive PhotoShot Function,
you can record still pictures with higher
resolution than with the normal PhotoShot
Function.
5
PHOTOSHOT
3, 4
JOG KEY
1
POWER
2
MENU
1
Set POWER to CAMERA.
2
Press PHOTOSHOT in Record/Pause
mode. “PHOTO” will appear in the
EVF or the LCD monitor.
EVF/LCD
Note
• If SHUTTER on the menu screen is set to
ON, a sound effect similar to the shutter
of a film camera will be heard when
PHOTOSHOT is pressed.
• When PHOTOSHOT is pressed, the
playback image takes approx. 7 seconds
to process. After that, the Camera mode
screen will be displayed.
1
Set POWER to CAMERA.
2
Press MENU to display the CAMERA
mode menu screen.
3
Rotate JOG KEY to select
D.FUNCTION , and press JOG KEY
to display the CAMERA FUNCTION
menu screen.
4
Rotate JOG KEY to select
PROGRESSIVE , and press JOG
KEY to select ON or OFF.
• Press MENU twice to exit.
•“P” will appear in the EVF or the
LCD monitor.
5
Press PHOTOSHOT in Record/Pause
mode.
EVF/LCD
Note
• This Function may not work with some
function settings.
20
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Zoom
You can gradually zoom in for close ups or
zoom out for wide angle shots.
2
POWER
ZOOM
1
POWER
3
REC/PAUSE
Zoom Microphone Function
Along with the zooming operation, the
microphone’s directional angle and
sensitivity are varied for recording sounds.
3, 4, 5
JOG KEY
1
POWER
2
MENU
Camera Recording
1
Set POWER to CAMERA.
2
Zoom slowly:
by lightly pressing the “T” (Telephoto)
or the “W” (Wide Angle) side of the
POWER ZOOM.
Zoom quickly:
by applying more pressure.
3
Start recording.
Note
• The zooming speed ranges from a slow
17 seconds to a fast 1.5 seconds
according to the amount of pressure
applied to the POWER ZOOM.
1
Set POWER to CAMERA.
2
Press MENU to display the CAMERA
mode menu screen.
3
Rotate JOG KEY to select REC
MODE , then press JOG KEY to
display the CAMERA REC-MODE
menu screen.
4
Rotate JOG KEY to select ZOOM-MIC
in the CAMERA REC-MODE menu.
(Menu OSD: p. 108)
5
Press JOG KEY to select ON.
• Press MENU twice to exit.
•“Z.MIC” will appear on the screen.
Note
• The Zoom Microphone Function may not
work effectively if the surrounding noise is
too loud.
Camera
21
Camera Recording
Recording Check
To playback the final few seconds of the
last recorded scene in the REC/PAUSE
mode.
1
RECORDING CHECK
Recording Still Pictures
You can record still pictures of any desired
duration together with sound.
1, 2
STILL
Self Recording
Rotate the LCD monitor 180 degrees so it
faces the same direction as the lens to
record yourself.
3, 4
JOG KEY
2
MENU
5
REC/
PAUSE
1
POWER
180°
1
Press RECORDING CHECK
briefly in the REC/PAUSE mode.
The [CHK] indication appears.
After checking, the Palmcorder returns
to the REC/PAUSE mode.
• For Recording Check, the Palmcorder
must be in the same mode (SP or LP) as
was used for recording, otherwise the
playback picture is distorted.
1
While in RECORD mode, press STILL
and hold for 2 seconds to capture a
still picture. The captured still picture
will be recorded together with sound.
2
Press STILL once again to release
the still picture. The camera will
resume recording real-time pictures.
1
Set POWER to CAMERA.
2
Press MENU to display the CAMERA
mode menu screen.
3
Rotate JOG KEY to select REC
MODE , then press JOG KEY to
display the CAMERA REC-MODE
menu screen.
4
Rotate JOG KEY to select SELF-
REC , and then press JOG KEY to
select MIRROR.
• The picture in the LCD monitor will
appear reversed.
5
Start recording.
22
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Special Effect Features
CINEMA Mode
You can record a picture compatible with a
wide-screen TV equipped with an S2
picture terminal.
3, 4
JOG KEY
1
POWER
1
Set POWER to CAMERA.
2
Press MENU to display the CAMERA
mode menu screen.
3
Rotate JOG KEY to select ADJUST ,
then press JOG KEY to display the
CAMERA ADJUST menu screen.
2
MENU
5
REC/PAUSE
Backlight
Use when recording a subject that is darker
than the surrounding scene, is in a
shadowed area, or when the light source is
in back of your subject.
1
POWER
4
Rotate JOG KEY to select CINEMA ,
and then press JOG KEY to select
ON.
• A black strip will appear at the top
and bottom of the picture.
• Press MENU twice to exit.
•“CINEMA” will appear on the screen.
5
Start recording.
1
Set POWER to CAMERA.
2
Press BACK LIGHT to activate the
Backlight feature.
• The Indicator “
EVF or LCD monitor.
3
Press BACK LIGHT again to cancel
the Backlight feature.
EVF/LCD
EVF/LCD
” will appear in the
Camera
2, 3
BACK LIGHT
Note
• The Indicator “
EVF or LCD monitor when OFF is
selected in the DISPLAY menu.
” will not appear in the
23
Special Effect Features
Program AE
The Auto Exposure feature can be used to
make quality recordings in a variety of
scene situations.
Note
• When MagicVu (PV-DV402 only) is ON,
Program AE and H.S.S. cannot be set in
the menu.
2
AUTO/MANUAL
4, 5
JOG KEY
3
MENU
1
POWER
(No display)
SPORTS
PORTRAIT
LOW-LIGHT
SPOT-LIGHT
SURF&SNOW
Note
SPORTS mode
• The recorded images will not be so blurred
when they are viewed later using slow or
still picture playback.
• When playing back a sports mode
recording, the movement may appear
slightly jerky.
• Do not use this mode when recording
under fluorescent, mercury, or sodium
lighting. These types of lights will affect
the color and brightness of the images.
• A vertical band of light might appear when
recording objects that are brightly
illuminated or highly reflective.
• If the amount of light is insufficient, the
SPORTS “
EVF or the LCD monitor.
• The image may flicker if this mode is
used indoors.
24
” indicator will flash in the
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
1
Set POWER to CAMERA.
2
Hold down AUTO/MANUAL for more
than 0.7 seconds so that the “MNL”
indication appears in the EVF or the
LCD monitor.
3
Press MENU to display the menu
screen.
4
Rotate JOG KEY to select ADJUST ,
and then press JOG KEY to display
the CAMERA ADJUST menu screen.
5
Rotate JOG KEY to select
PROG.AE , then press JOG KEY
repeatedly to select one of the five
modes shown below.
6
Repeat steps 2~5 to select OFF to
cancel this feature.
Mode
For recording fast action scenes.
For recording only subjects in the
foreground, while ignoring
subjects in the background.
For recording in extreme low light
conditions.
Recording in situations where
subjects are under a spotlight(s).
For recording in locations with a
high degree of “Dazzle,” such as
snow slopes and the seashore.
PORTRAIT mode
• The image may flicker if this mode is
used indoors.
LOW-LIGHT mode
• Scenes recorded in extremely low light
levels may not come out properly.
SPOT-LIGHT mode
• If the recorded subject is extremely bright,
the picture may appear whitish.
SURF&SNOW mode
• If the recorded subject is extremely bright,
the picture may appear whitish.
• It is not possible to select the SPORTS
mode or PORTRAIT mode together with
the MagicPix mode in the Digital function
camera menu.
Indication
Special Effect Features
Audio/Video Fade In/Out
You can make smoother scene transitions
for a more professional look.
1, 3, A
2, B
REC/
PAUSE
MagicVu™ IR Filter (0 Lux)
(PV-DV402 only)
MagicVu allows you to record video in total
darkness. You can select the color of
image: B/W, green, or blue.
(Menu OSD: p. 109)
2
MAGICVU/
0LUX
4, 5
JOG
KEY
3
MENU
1
POWER
FADE
Fade In
Starting the first scene with “fade in” is very
effective.
1
In REC/PAUSE mode, hold down
FADE until the picture fades out.
2
Press REC/PAUSE to start
recording.
3
Release FADE and the picture will
gradually fade in.
Fade Out
Use to create a soft ending or (together
with fade in) for a soft transition from one
scene to the next.
A
During recording, hold down FADE
until the picture fades out.
B
Press REC/PAUSE to pause the
recording.
1
Set POWER to CAMERA.
2
Slide MAGICVU/0LUX to ON.
• A black and white image appears.
•“ MAGICVU” will appear on the
screen.
3
Press MENU to display the menu
screen.
4
Rotate JOG KEY to select SET-UP ,
and then press JOG KEY to display
the CAMERA SET-UP menu screen.
5
Rotate JOG KEY to select MAGICVU ,
and then press JOG KEY repeatedly
to select B/W, BLUE, or GREEN.
• Press MENU twice to exit.
• To cancel this feature, slide
MAGICVU/0LUX to OFF.
Note
• The subject can be up to 3 m (9 feet)
away.
25
Camera
Special Effect Features
Picture in Picture (PinP)
You can display a PinP (still image) screen
on the Main Picture.
Note
• PinP position is fixed at the bottom right
of the screen.
Main Picture
Picture in Picture
(PinP still image)
PHOTOSHOT
3, 4
JOG
KEY
1
POWER
2
MENU
1
Set POWER to CAMERA.
2
Press MENU to display the menu
screen.
3
Rotate JOG KEY repeatedly to select
D.FUNCTION , then press JOG KEY
to display the CAMERA FUNCTION
menu screen.
4
Press JOG KEY to select PinP .
• Press MENU twice to exit this menu.
•“PinP” will appear in the EVF or the
LCD monitor.
5
Aim at the scene you wish to place as
PinP, then press
to freeze the image.
6
Press (CAMERA STILL) again to
place the frozen image as PinP.
(CAMERA STILL)
7
REC/
PAUSE
7
5, 6, 7
CAMERA STILL
26
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Press REC/PAUSE to record a scene
with PinP image.
• Press PHOTOSHOT to record a
scene with PinP image in PhotoShot
mode.
• Press
(CAMERA STILL) again to
remove PinP image.
Special Effect Features
Photo Title
You can use PhotoShot images stored on a
Memory Card to record a WIPE or MIX
effect on a cassette.
Note
When Photo Title is set to ON, the selected
image and Title will appear before each
recording is made.
WIPE : The Photo title is replaced with the
MIX : The photo title is replaced with the
current scene in a wiping motion.
current scene in a gradual mixing
effect.
2, 3, 4
JOG KEY
1
POWER
2
MENU
Before you begin
• Connect the Palmcorder to a power
source. (pp. 14, 15)
• Set POWER to OFF before inserting a
recorded Memory Card. (pp. 48, 49)
1
Set POWER to CAMERA.
2
Press MENU to display the CAMERA
menu screen. Then rotate and press
JOG KEY to select PHOTO TITLE .
3
Rotate and press JOG KEY to select
and set MODE and then TITLE .
1st : Select and set MODE (WIPE or
MIX).
2nd: Select and set TITLE to “SET”.
•“PLEASE WAIT” appears on-screen.
• The Multi image screen is displayed.
4
Rotate and press JOG KEY to select
and set an image.
•“PLEASE WAIT” is displayed while
image is processed. Then, “PHOTO
TITLE SET” is displayed for approx.
3 seconds, and the screen goes back
to the Camera mode screen.
• After Photo Title is performed, Digital
Function turns off.
5
Press REC/PAUSE to start recording
with Photo Title.
• WIPE or MIX screen is displayed at
the beginning of the recording. Then
the Photo Title setting will be cleared
automatically.
Camera
5
REC/
PAUSE
27
Advanced Settings
White Balance
Auto White Balance (“AWB”) automatically
maintains optimum color balance in most
lighting conditions. However, when using
Digital Functions, etc., you may get better
results by using the manual adjustment.
3, 4, A, B
JOG KEY
1
POWER
2
AUTO/MANUAL
Mode
Automatically maintains optimum
color balance in most lighting
AWB
conditions.
When the source illumination is a
halogen lamp.
When shooting outdoors on a
sunny day.
The White Balance setting that
*
was previously set manually.
Note
• When ZOOM is set to 10X or higher,
White Balance cannot be adjusted.
Description
1
Set POWER to CAMERA.
2
Hold down AUTO/MANUAL for more
than 0.7 seconds so that the “MNL”
indication appears in the EVF or the
LCD monitor.
3
Press JOG KEY repeatedly until
“AWB” appears in the EVF or LCD
monitor.
4
Rotate JOG KEY to select other
modes. (See mode chart at left.)
• Hold down AUTO/MANUAL for more
than 0.7 seconds to cancel the
setting.
*For manual White Balance
adjustment:
A.
Rotate JOG KEY to select “ ” .
B.
Point the Palmcorder at a white
object (full-screen) and hold JOG
KEY down until “
flashing.
• If “
” indication flashes when the
Palmcorder is turned on, the previous
manual White Balance setting is in
effect.
In the following cases, the “
indication flashes:
• The flashing indicates that the
previously adjusted White Balance
setting is still kept. This setting will be
kept until White Balance is adjusted
again.
• Correct White Balance may not be
attainable manually in poor lighting.
” indication stops
”
28
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Advanced Settings
Auto Focus
The Palmcorder automatically adjusts the focus over the entire zoom range.
Manual Focus
Use Manual Focus (MF) when recording ...
• a subject through glass.
• a scene where the subject is far from the
Palmcorder and there are objects in the
foreground.
• a subject with distinct horizontal stripes.
• a subject not centered in the Viewfinder.
• subjects with shiny surfaces.
• an obliquely angled subject.
• a bright, flat subject such as a white wall.
• in low light situations.
• a scene with fast motions, like a golf swing.
Re-focusing may be required
• when your Palmcorder is aimed at a new
scene.
4, 6
POWER
ZOOM
5
M.FOCUS
DIAL
1
POWER
2
AUTO/
MANUAL
3
FOCUS
1
Set POWER to CAMERA.
2
Hold down AUTO/MANUAL for more
than 0.7 seconds so that the “MNL”
indication appears in the EVF or the
LCD monitor.
3
Press FOCUS so that the “MF”
(Manual Focus) indication appears in
the EVF or the LCD monitor.
4
Press and hold POWER ZOOM, “T”
side (Telephoto), until the lens is at
maximum zoom in.
5
Turn M.FOCUS DIAL until the picture
is in focus.
• It may be necessary to back away
from the subject to focus the image
properly.
6
Press POWER ZOOM to “W” or “T”
as desired.
• The subject will remain in focus over
the entire zooming range.
• It may be necessary to back away
from the subject to focus the image
properly.
Note
• DISPLAY must be set to on for MF, AE,
W.BALANCE, or BACK LIGHT to be
displayed on the LCD or EVF.
Camera
Macro Focus (for close-ups)
Press the “W” side of POWER ZOOM to the maximum wide angle position.
Auto Focus will function with the subject as close as 25 mm (1 inch) in front of the lens.
29
Advanced Settings
High Speed Shutter
To record high speed motion (e.g. tennis
stroke) with improved STILL or SLOW
MOTION playback when watching the tape
on this Palmcorder.
Auto Shutter
In the AUTO mode (no indication in the EVF and LCD monitor), the Palmcorder will
automatically adjust the shutter speed (up to 1/350).
• AUTO mode is automatically selected whenever the POWER Switch is set to CAMERA.
Manual Selection
1
Set POWER to CAMERA.
2
Hold down AUTO/MANUAL for more
3, 4
JOG KEY
1
POWER
2
AUTO/MANUAL
than 0.7 seconds so that the “MNL”
indication appears in the EVF or the
LCD monitor.
3
Press JOG KEY repeatedly to display
the shutter speed.
4
Rotate JOG KEY to choose one of the
following shutter speeds.
• Hold down AUTO/MANUAL for more
than 0.7 seconds to cancel the setting.
EVF/LCD
Note
• For proper color reproduction, it is
recommended that you use this feature
outdoors. For indoor High Speed Shutter
recording, additional halogen or tungsten
light should be provided. Fluorescent light
will degrade the picture quality.
• This feature requires ample light. More
light is required for the fastest shutter
speeds.
• The Auto Focus system may not operate
properly in insufficient light when using
the High Speed Shutter.
• When PROG.AE is ON, you cannot
manually select the shutter speed.
• When MagicVu (PV-DV402 only) is ON,
Program AE and H.S.S. cannot
manually select the shutter speed.
• When MagicPix is ON, H.S.S. cannot
manually select the shutter speed.
30
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Loading...