Panasonic pt-vX610u, pt-vz580u, pt-vw540u operating instructions
Operating Instructions
Functional Manual
LCD Projector
Model No.
PT-VZ580
PT-VW540
PT-VX610
Commercial Use
Thank you for purchasing this Panasonic product.
■ Before operating this product, please read the instructions carefully, and save this manual for
future use.
■ Before using your projector, be sure to read “Read this rst!” (Æ pages 4 to 12).
ENGLISH
DPQP1166ZB
Contents
Contents
Read this first! ............................................4
Chapter 1 Preparation
Precautions for use ................................................. 16
Cautions when transporting .................................. 16
Cautions when installing ....................................... 16
Cautions when setting the projectors ................... 17
Security ................................................................ 18
Early Warning Software ........................................ 18
Storage ................................................................. 18
Disposal ................................................................ 18
Cautions on use ................................................... 19
Accessories .......................................................... 20
Optional accessories ............................................ 21
About your projector ............................................... 22
Remote control ..................................................... 22
Projector body ...................................................... 23
Preparing the remote control ................................. 26
Inserting and removing batteries .......................... 26
When using the system with multiple projectors .. 26
Attaching the lens cap ............................................ 27
Chapter 2 Getting Started
Setting up ................................................................. 29
Installation mode .................................................. 29
Parts for ceiling mount (optional) .......................... 30
Screen size and throw distance ........................... 30
Connecting ............................................................... 34
Before connecting ................................................ 34
Connecting example: AV equipment .................... 35
Connecting example: Computers ......................... 36
Chapter 3 Basic Operations
Switching on/off the projector ................................ 38
Connecting the power cord .................................. 38
Power indicator ..................................................... 38
Switching on the projector .................................... 39
When the initial setting screen is displayed .......... 40
Making adjustments and selections ..................... 42
Switching off the projector .................................... 42
Direct power off function ....................................... 43
Projecting ................................................................. 44
Selecting the image input for projection ............... 44
How to adjust the state of the image .................... 45
Adjusting adjustable feet ...................................... 46
Adjusting the projection position with the optical
axis shift function ............................................... 47
Operating with the remote control ......................... 48
Using the AV mute function .................................. 48
Using the mute function ........................................ 48
Adjusting the volume ............................................ 48
Using the freeze function ...................................... 49
Using the auto setup function ............................... 49
Using the screen adjustment function .................. 49
Using the digital zoom function ............................ 50
Using the FUNCTION button ................................ 50
Using the presentation timer function ................... 51
Setting the ID number on the remote control ....... 51
Chapter 4 Settings
On-screen menu ...................................................... 53
Navigating through the menu ............................... 53
Main menu ............................................................ 54
Sub menu ............................................................. 55
[PICTURE] menu ...................................................... 57
[PICTURE MODE] ................................................ 57
[CONTRAST] ........................................................ 57
[BRIGHTNESS] .................................................... 57
[COLOR] ............................................................... 57
[TINT] ................................................................... 58
[SHARPNESS] ..................................................... 58
[COLOR TEMPERATURE] ................................... 58
[GAMMA] .............................................................. 59
[IRIS] .................................................................... 59
[DAYLIGHT VIEW] ................................................ 59
[DIGITAL CINEMA REALITY] ............................... 59
[NOISE REDUCTION] .......................................... 60
[TV-SYSTEM] ....................................................... 60
[RGB/YCBCR] / [RGB/YPBPR] ................................ 60
[RGB-SYSTEM] .................................................... 61
[POSITION] menu .................................................... 62
[REALTIME KEYSTONE] ..................................... 62
[SCREEN ADJUSTMENT] ................................... 62
[SHIFT] ................................................................. 65
[DOT CLOCK]....................................................... 66
[CLOCK PHASE] .................................................. 66
[OVER SCAN] ...................................................... 67
[ASPECT] ............................................................. 67
[FRAME LOCK] .................................................... 68
[LANGUAGE] menu ................................................. 69
Switching the display language ............................ 69
[DISPLAY OPTION] menu ....................................... 70
[COLOR ADJUSTMENT] ...................................... 70
[COLOR CORRECTION] ..................................... 71
[ON-SCREEN DISPLAY] ...................................... 71
[HDMI SIGNAL LEVEL] ........................................ 73
2 - ENGLISH
Contents
[CLOSED CAPTION SETTING] (Only for NTSC
input) ................................................................. 73
[SCREEN SETTING] ........................................... 74
[STARTUP LOGO] ................................................ 74
[AUTO SETUP SETTING] .................................... 75
[SIGNAL SEARCH] .............................................. 75
[BACK COLOR] .................................................... 75
[P-TIMER] ............................................................. 75
[OTHER FUNCTIONS] ......................................... 76
[PROJECTOR SETUP] menu .................................. 78
[STATUS] .............................................................. 78
[COMPUTER2 SELECT] ...................................... 78
[PROJECTOR ID] ................................................. 78
[INITIAL START UP] ............................................. 79
[PROJECTION METHOD] .................................... 79
[LAMP POWER] ................................................... 79
[ECO MANAGEMENT] ......................................... 80
[EMULATE] ........................................................... 81
[FUNCTION BUTTON] ......................................... 82
[AUDIO SETTING] ............................................... 82
[TEST PATTERN] ................................................. 83
[FILTER COUNTER]............................................. 84
[DC OUT] .............................................................. 85
[INITIALIZE ALL] .................................................. 85
[SECURITY] menu ................................................... 86
[PASSWORD] ....................................................... 86
[PASSWORD CHANGE] ...................................... 86
[TEXT DISPLAY] .................................................. 87
[TEXT CHANGE] .................................................. 87
[MENU LOCK] ...................................................... 87
[MENU LOCK PASSWORD] ................................ 87
[CONTROL DEVICE SETUP] ............................... 88
[NETWORK] menu ................................................... 89
[WIRED LAN] ....................................................... 89
[PROJECTOR NAME] .......................................... 89
[NETWORK CONTROL] ...................................... 89
[NETWORK STATUS] .......................................... 90
[INITIALIZE] .......................................................... 90
Chapter 5 Operation of Function
Network connection ................................................ 92
Connecting via wired LAN .................................... 92
Web control function ............................................... 94
Computer that can be used for setting ................. 94
Accessing from the web browser ......................... 94
Chapter 6 Maintenance
Lamp and temperature indicators........................ 110
When an indicator lights up .................................110
Maintenance/replacement......................................111
Before performing maintenance/replacement .....111
Maintenance ........................................................ 111
Replacement .......................................................113
Troubleshooting .................................................... 117
Chapter 7 Appendix
Technical information ........................................... 119
PJLink protocol ....................................................119
Control commands via LAN ................................ 120
<SERIAL IN> terminal ........................................ 122
[MENU LOCK PASSWORD] operations ............ 125
List of compatible signals ................................... 126
Specications ........................................................ 128
Dimensions ............................................................ 131
Ceiling mount bracket safeguards....................... 132
Index ....................................................................... 133
ENGLISH - 3
Read this rst!
Read this rst!
WARNING:
WARNING: To prevent damage which may result in re or shock hazard, do not expose this appliance to rain
The sound pressure level at the operator position is equal or less than 70 dB (A) according to ISO 7779.
WARNING:
1. Remove the plug from the mains socket when this projector is not in use for a prolonged period of time.
2. To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualied
service personnel.
3. Do not remove the earthing pin on the mains plug. This apparatus is equipped with a three prong earthing
type mains plug. This plug will only t an earthing-type mains socket. This is a safety feature. If you are
unable to insert the plug into the mains socket, contact an electrician. Do not defeat the purpose of the
earthing plug.
WARNING:
This equipment is compliant with Class A of CISPR32.
In a residential environment this equipment may cause radio interference.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
THIS APPARATUS MUST BE EARTHED.
or moisture.
This device is not intended for use in the direct eld of view at visual display workplaces. To avoid
incommoding reections at visual display workplaces this device must not be placed in the direct
eld of view.
The equipment is not intended for used at a video workstation in compliance BildscharbV.
TO RAIN OR MOISTURE.
WARNING: RISK OF ELECTRIC SHOCK. DO NOT OPEN.
AVERTISSEMENT:RISQUEDECHOCÉLECTRIQUE.
NEPASOUVRIR.
WARNUNG:ZURVERMEIDUNGEINESELEKTRISCHEN
SCHLAGESGERÄTNICHTÖFFNEN.
ПРЕДУПРЕЖДЕНИЕ:ОПАСНОСТЬ ПОРАЖЕНИЯ ЭЛЕКТРИЧЕСКИМ
ТОКОМ. НЕ ОТКРЫВАТЬ.
경고:감전 위험이 있으므로 열지마십시오.
Indicated on the projector
The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the
o
7
WARNING: TURN THE POWER OFF AND DISCONNECT THE POWER PLUG FROM THE WALL OUTLET
WARNING: Do not look at the light emitted from the lens while the projector is being used.
user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may
be of sufcient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
product.
BEFORE REPLACING THE LAMP UNIT.
Indicated on the projector
WARNING: Do not place objects in front of the lens while the projector is being used.
Indicated on the projector
4 - ENGLISH
Read this rst!
CAUTION: To assure continued compliance, follow the attached installation instructions. This includes using
the provided power cord and shielded interface cables when connecting to computer or peripheral
devices. Also, any unauthorized changes or modications to this equipment could void the user's
authority to operate this device.
This is a device to project images onto a screen, etc., and is not intended for use as indoor lighting in a
domestic environment.
Directive 2009/125/EC
CAUTION (North/Middle/South America)
This equipment is equipped with a three-pin grounding-type power plug. Do not
remove the grounding pin on the power plug. This plug will only t a grounding-type
power outlet. This is a safety feature. If you are unable to insert the plug into the
outlet, contact an electrician. Do not defeat the purpose of the grounding plug.
Do not remove
WARNING (USA and Canada)
• Not for use in a computer room as dened in the Standard for the Protection of Electronic Computer/Data
Processing Equipment, ANSI/NFPA 75.
• For permanently connected equipment, a readily accessible disconnect device shall be incorporated in the
building installation wiring.
• For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily
accessible.
NOTIFICATION (Canada)
This class A digital apparatus complies with Canadian ICES-003.
Contains mercury / Contenu avec mercure
For more information on safe handling
procedures, the measures to be taken in
case of accidental breakage and safe
disposal options visit:
ec.gc.ca/mercure-mercury/.
Dispose of or recycle in accordance with
applicable laws.
Pour plus de renseignements sur les
procédures de manutention sécuritaire, les
mesures à prendre en cas de bris accidentel et
les options d’élimination sécuritaire visitez:
ec.gc.ca/mercure-mercury/.
Mettez au rebut ou recyclez conformément
aux lois applicables.
NOTIFICATION (USA)
• This product has a High Intensity Discharge (HID) lamp that contains mercury. Disposal may be regulated
in your community due to environmental considerations. For disposal or recycling information, please visit
Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149.
ENGLISH - 5
Read this rst!
FCC NOTICE (USA)
Verication
Model Number: PT-VZ580, PT-VW540, PT-VX610
Trade Name: Panasonic
Responsible Party: Panasonic Corporation of North America
Address: Two Riverfront Plaza, Newark, NJ 07102-5490
General Contact: http://www.panasonic.com/support
Projector Contact: https://panasonic.net/cns/projector/
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Warning:
To assure continued compliance, follow the attached installation instructions. This includes using the provided
power cord and shielded interface cables when connecting to computer or peripheral devices. Also, any
unauthorized changes or modications to this equipment could void the user’s authority to operate this device.
6 - ENGLISH
Read this rst!
IMPORTANT: THE MOULDED PLUG
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse
is tted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating
of 13 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is retted when the fuse is replaced. If you
lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover
can be purchased from an Authorised Service Center.
If the tted moulded plug is unsuitable for the mains socket in your home, then the fuse should be removed and
the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted
into any 13 amp socket.
If a new plug is to be tted, please observe the wiring code as shown below.
If in any doubt, please consult a qualied electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Green - and - Yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows.
The wire which is coloured GREEN - AND - YELLOW must be connected to the terminal in the
plug which is marked with the letter E or by the Earth symbol or coloured GREEN or GREEN -
AND - YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked
with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug which is marked
with the letter L or coloured RED.
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.
Importer's name and address within the European Union
Panasonic Marketing Europe GmbH
Panasonic Testing Centre
Winsbergring 15, 22525 Hamburg, Germany
ENGLISH - 7
Read this rst!
WARNING:
POWER
The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily
accessible when problems occur. If the following problems occur, cut off the power supply
immediately.
Continued use of the projector in these conditions will result in re or electric shock.
z If foreign objects or water get inside the projector, cut off the power supply.
z If the projector is dropped or the cabinet is broken, cut off the power supply.
z If you notice smoke, strange smells or noise coming from the projector, cut off the power supply.
Please contact an Authorized Service Center for repairs, and do not attempt to repair the projector yourself.
During a thunderstorm, do not touch the projector or the cable.
Electric shocks can result.
Do not do anything that might damage the power cord or the power plug.
If the power cord is used while damaged, electric shocks, short-circuits or re will result.
zDo not damage the power cord, make any modications to it, place it near any hot objects, bend it
excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.
Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary.
Completely insert the power plug into the wall outlet and the power connector into the projector
terminal.
If the plug is not inserted correctly, electric shocks or overheating will result.
z Do not use plugs which are damaged or wall outlets which are coming loose from the wall.
Do not use anything other than the provided power cord.
Failure to observe this will result in re or electric shocks. Please note that if you do not use the provided power
cord to ground the device on the side of the outlet, this may result in electric shocks.
Clean the power plug regularly to prevent it from becoming covered in dust.
Failure to observe this will cause a re.
zIf dust builds up on the power plug, the resulting humidity can damage the insulation.
zIf not using the projector for an extended period of time, pull the power plug out from the wall outlet.
Pull the power plug out from the wall outlet and wipe it with a dry cloth regularly.
Do not handle the power plug and power connector with wet hands.
Failure to observe this will result in electric shocks.
Do not overload the wall outlet.
If the power supply is overloaded (ex., by using too many adapters), overheating may occur and re will result.
ON USE/INSTALLATION
Do not place the projector on soft materials such as carpets or sponge mats.
Doing so will cause the projector to overheat, which can cause burns, re or damage to the projector.
Do not set up the projector in humid or dusty places or in places where the projector may come into
contact with oily smoke or steam.
Using the projector under such conditions will result in re, electric shocks or deterioration of components. Oil
may also distort the plastic and the projector could fall such as when mounted on the ceiling.
Do not install this projector in a place which is not strong enough to take the full weight of the
projector or on top of a surface which is sloped or unstable.
Failure to observe this will cause projector to fall down or tip over the projector, and severe injury or damage
could result.
Installation work (such as ceiling mount bracket) should only be carried out by a qualied technician.
If installation is not carried out and secured correctly, it can cause injury or accidents, such as electric shocks.
z Be sure to use the wire provided with the ceiling mount bracket as an extra safety measure to prevent the
projector from falling down. (Install in a different location to the ceiling mount bracket.)
Do not cover the air intake/exhaust ports.
Doing so will cause the projector to overheat, which can cause re or damage to the projector.
z Do not place the projector in narrow, badly ventilated places.
z Do not place the projector on cloth or papers, as these materials could be drawn into the air intake port.
z Provide at least 1 m (39-3/8") of space between any walls or objects and the exhaust port, and at least
50 cm (19-11/16") of space between any walls or objects and the intake port.
8 - ENGLISH
Read this rst!
WARNING:
Do not place your hands or other objects close to the air exhaust port.
Doing so will cause burns or damage your hands or other objects.
z Heated air comes out of the air exhaust port. Do not place your hands or face, or objects which cannot
withstand heat close to this port.
Do not look at and place your skin into the lights emitted from the lens while the projector is being
used.
Doing so can cause burns or loss of sight.
z Strong light is emitted from the projector’s lens. Do not look at or place your hands directly into this light.
z Be especially careful not to let young children look into the lens. In addition, turn off the power and
disconnect the power plug when you are away from the projector.
Never attempt to remodel or disassemble the projector.
High voltages can cause re or electric shocks.
z For any inspection, adjustment and repair work, please contact an Authorized Service Center.
Do not allow metal objects, ammable objects, or liquids to enter inside of the projector. Do not allow
the projector to get wet.
Doing so may cause short circuits or overheating, and result in re, electric shock, or malfunction of the
projector.
z Do not place containers of liquid or metal objects near the projector.
z If liquid enters inside of the projector, consult your dealer.
z Particular attention must be paid to children.
Use the ceiling mount bracket specied by Panasonic.
Using the ceiling mount bracket other than the specied one will result in falling accidents.
z Attach the supplied safety cable to the ceiling mount bracket to prevent the projector from falling down.
ACCESSORIES
Do not use or handle the batteries improperly, and refer to the following.
Failure to observe this will cause burns, batteries to leak, overheat, explode or catch re.
z Do not use unspecied batteries.
z Do not charge dry cell batteries.
z Do not use chargeable batteries.
z Do not disassemble dry cell batteries.
z Do not heat the batteries or place them into water or re.
z Do not allow the + and - terminals of the batteries to come into contact with metallic objects such as
necklaces or hairpins.
z Do not store or carry batteries together with metallic objects.
z Store the batteries in a plastic bag and keep them away from metallic objects.
z Make sure the polarities (+ and -) are correct when inserting the batteries.
z Do not use a new battery together with an old battery or mix different types of batteries.
z Do not use batteries with the outer cover peeling away or removed.
Do not allow children to reach the batteries.
Accidentally swallowing them can cause physical harm.
z If swallowed, seek medical advice immediately.
If the battery uid leaks, do not touch it with bare hands, and take the following measures if necessary.
z Battery uid on your skin or clothing could result in skin inammation or injury.
Rinse with clean water and seek medical advice immediately.
z Battery uid coming in contact with your eyes could result in loss of sight.
In this case, do not rub your eyes. Rinse with clean water and seek medical advice immediately.
Do not remove unspecied screws during the lamp unit replacement.
Doing so can cause electric shocks, burns, or injury.
Do not disassemble the lamp unit.
If the lamp breaks, it could cause injury.
ENGLISH - 9
Read this rst!
WARNING:
Lamp replacement
The lamp has high internal pressure. If improperly handled, an explosion and severe injury or accidents will
result.
z The lamp can easily explode if struck against hard objects or dropped.
z Before replacing the lamp unit, be sure to turn the power off and to disconnect the power plug from the wall
outlet. Electric shocks or explosions can result if this is not done.
z When replacing the lamp, turn the power off and allow the lamp it to cool for at least 1 hour before handling
it otherwise it can cause burns.
Remove the depleted batteries from the remote control promptly.
z Leaving them in the unit may result in uid leakage, overheating, or explosion of the batteries.
CAUTION:
POWER
When disconnecting the power cord, be sure to hold the power plug and power connector.
If the power cord itself is pulled, the lead will become damaged, and re, short-circuits or serious electric
shocks will result.
When not using the projector for an extended period of time, disconnect the power plug from the wall
outlet.
Failure to do so may result in re or electric shock.
Disconnect the power plug from the wall outlet before carrying out any cleaning and replacing the unit.
Failure to do so may result in electric shock.
ON USE/INSTALLATION
Do not place heavy objects on top of the projector.
Failure to observe this will cause the projector to become unbalanced and fall, which could result in damage or
injury. The projector will be damaged or deformed.
Do not put your weight on this projector.
You could fall or the projector could break, and injury will result.
z Be especially careful not to let young children stand or sit on the projector.
Do not place the projector in extremely hot locations.
Doing so will cause the outer casing or internal components to deteriorate, or result in re.
z Take particular care in locations exposed to direct sunlight or near stoves.
Do not install the projector in a location where salt pollution or corrosive gas may occur.
z Doing so may result in falling due to corrosion. Also, it may result in malfunctions.
Do not stand in front of the lens while the projector is being used.
Doing so can cause damage and burns to clothing.
z Strong light is emitted from the projector’s lens.
Do not place objects in front of the lens while the projector is being used.
Doing so can cause re, damage to an object, or malfunction of the projector.
z Strong light is emitted from the projector’s lens.
Always disconnect all cables before moving the projector.
Moving the projector with cables still attached can damage the cables, which will cause re or electric shocks to
occur.
When mounting the projector on the ceiling, keep mounting screws and power cord from contact with
metal parts inside the ceiling.
Contact with metal parts inside the ceiling can cause electric shocks.
Never plug headphones and earphones into <VARIABLE AUDIO OUT> terminal.
Excessive sound pressure from earphones and headphones can cause hearing loss.
Do not project an image with the lens cap attached.
Doing so can cause re.
10 - ENGLISH
Read this rst!
CAUTION:
ACCESSORIES
Do not use the old lamp unit.
If used it could cause lamp explosion.
If the lamp has broken, ventilate the room immediately. Do not touch or bring your face close to the
broken pieces.
Failure to observe this will cause the user to absorb the gas which was released when the lamp broke and
which contains nearly the same amount of mercury as uorescent lamps, and the broken pieces will cause
injury.
z If you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek medical
advice immediately.
z Ask your dealer about replacing the lamp unit and check the inside of the projector.
When not using the projector for an extended period of time, remove the batteries from the remote
control.
Failure to observe this will cause the batteries to leak, overheat, catch re or explode, which may result in re
or contamination of surrounding area.
Do not open the desiccant bag, or do not eat the contents.
If swallowed the contents of the desiccant bag accidentally, it may cause bad result to your body.
z If the desiccant gets into your eyes or mouth, immediately rinse with clean water and seek medical advice.
z Be especially careful not to let children reach the desiccant.
MAINTENANCE
Do not attach the air lter unit while it is wet.
Doing so may result in electric shock or malfunctions.
z After you clean the air lter units, dry them thoroughly before reattaching them.
Ask your dealer about cleaning inside the projector once a year.
Continuous use while dust is accumulated inside the projector may result in re.
z For cleaning fee, ask your dealer.
ENGLISH - 11
Read this rst!
To remove the battery
1. Press the guide and lift the cover. 2. Remove the batteries.
Brazil Only
Brasil Apenas
Manuseio de baterias usadas
BRASIL
Após o uso, as pilhas e /ou baterias deverão
ser entregues ao estabelecimento comercial
ou rede de assistência técnica autorizada.
Cobrir os terminais positivo (+) e negativo (-) com uma fita isolante adesiva, antes de depositar numa
caixa destinada para o recolhimento. O contato entre partes metálicas pode causar vazamentos,
gerar calor, romper a blindagem e produzir fogo. (Fig. 1)
Fig. 1
Como isolar os terminais
Não desmonte, não remova o invólucro, nem amasse a bateria. O gás liberado pela bateria pode irritar a
garganta, danicar o lacre do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo
devido ao curto circuito dos terminais. Não incinere nem aqueça as baterias, elas não podem car expostas a
temperaturas superiores a 100 °C (212 °F). O gás liberado pela bateria pode irritar a garganta, danicar o lacre
do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo devido ao curto circuito dos
terminais provocado internamente.
Evite o contato com o liquido que vazar das baterias. Caso isto ocorra, lave bem a parte afetada
com bastante água. Caso haja irritação, consulte um médico.
Fita Isolante
Fita Isolante
Remoção das baterias
1. Pressione a guia e levante a tampa. 2. Remova as baterias.
12 - ENGLISH
r Trademarks
f The terms HDMI and HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
f PJLink™ is a trademark or pending trademark in Japan, the United States, and other countries and regions.
f RoomView, Crestron RoomView are registered trademarks of Crestron Electronics, Inc, and Crestron
Connected™ and Fusion RV are trademarks of Crestron Electronics, Inc.
f Windows, Internet Explorer and Microsoft Edge are registered trademarks or trademarks of Microsoft
Corporation in the United States and other countries.
f Mac, Mac OS and Safari are trademarks of Apple Inc., registered in the United States and other countries.
f Adobe, Adobe Flash Player and Adobe Reader are trademarks or registered trademarks of Adobe Systems Inc.
in the United States and/or other countries.
f Some of the fonts used in the on-screen menu are Ricoh bitmap fonts, which are manufactured and sold by Ricoh
Company, Ltd.
f Other names, company names or product names used in these operating instructions are the trademarks or
registered trademarks of their respective holders.
Please note that the operating instructions do not include the ® and ™ symbols.
r Illustrations in these operating instructions
f Note that illustrations of the projector and screens may differ from the ones you actually see.
f The illustrations displayed on the computer screen may differ depending on the computer type and its operating
system.
r Page references
f Reference pages in this manual are indicated as: (Æ page 00).
r Term
f In this manual, the “Wireless remote control unit” accessory is referred to as the “Remote control”.
ENGLISH - 13
Features of the Projector
Quick Steps
Excellent Basic Performance
▶ Unique optical system, lamp dimming
system and the DAYLIGHT VIEW function
allow you to project a good-quality image
even in a bright room.
▶ It has many useful functions such as
compact design for portability and multiple
input interface etc.
Easy Setup
▶ The adoption of 1.6x optical zoom and the
lens shift function ensures highly exible
setup of the projector.
▶ KEYSTONE, CORNER CORRECTION and
CURVED CORRECTION functions allow
easy correction of various image distortions
occurred in the installation location.
Maintenance cost down
For details, refer to the corresponding pages.
1. Set up your projector.
(Æ page 29)
2. Connect with external devices.
(Æ page 34)
3. Connect the power cord.
(Æ page 38)
4. Power on.
(Æ page 39)
▶ The long life lamp with new lamp driving
system and the water wash enabled
long life lter have greatly reduced the
maintenance time and the cost.
5. Make initial settings.
(Æ page 40)
fTake this step when you power on for the rst time after
purchasing the projector.
6. Select the input signal.
(Æ page 44)
7. Adjust the image.
(Æ page 45)
14 - ENGLISH
Chapter 1 Preparation
This chapter describes things you need to know or check before using the projector.
ENGLISH - 15
Chapter 1 Preparation - Precautions for use
Precautions for use
Cautions when transporting
f When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts. Doing
so may damage the internal parts and result in malfunctions.
f Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.
Cautions when installing
r Do not set up the projector outdoors.
The projector is designed for indoor use only.
r Do not use under the following conditions.
f Places where vibration and impacts occur such as in a car or vehicle: Doing so may damage the internal parts
and result in malfunctions.
f Location close to sea or where corrosive gas may occur: the projector may fall due to corrosion. Also, failure to
do so may shorten the life of the components and result in malfunction.
f Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may uctuate in rare
cases due to the heated air from the air exhaust port or the hot or cooled air. Make sure that the exhaust
from the projector or other equipment, or the air from the air conditioner does not blow toward the front of the
projector.
f Places with sharp temperature uctuations such as near lights (studio lamps): Doing so may shorten the life of
the luminous lamp, or result in deformation of the outer case due to heat, which may cause malfunction. Make
sure to observe the operating temperature range of the projector.
f Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.
r Be sure to ask a specialized technician or your dealer when installing the product to a
ceiling.
This requires an optional ceiling mount bracket. Be sure to use the Projector Mount Bracket together with the
ceiling mount bracket for high ceilings or low ceilings.
Model No.:
① ET-PKL100H (for high ceilings), ET-PKV400B (Projector Mount Bracket)
② ET-PKL100S (for low ceilings), ET-PKV400B (Projector Mount Bracket)
r Focus adjustment
The projection lens is thermally affected by the light from the light source, making the focus unstable in the period
just after switching on the power. It is recommended that the images are projected continuously for at least 30
minutes before the focus is adjusted.
r Do not install the projector at elevations of 2 700 m (8 858') or higher above sea level.
r Do not use the projector in a location that the ambient temperature exceed 40 °C
(104 °F).
Using the projector in a location that the altitude is too high or the ambient temperature is too high may shorten
the life of the components or result in malfunctions.
The upper limit of the operating temperature of the projector varies depending on the altitudes of the operating
environment.
When using it at altitudes below 1 200 m (3 937') above sea level: 0 °C (32 °F) ~ 40 °C (104 °F)
When using it at altitudes between 1 200 m (3 937') and 2 700 m (8 858') above sea level: 0 °C (32 °F) ~ 30 °C
(86 °F)
r Do not tilt the projector or place it on its side.
Do not tilt the projector body more than approximately ±30 degrees longitudinally or ±15 degrees laterally. Over
tilting may result in shortening the life of the components.
16 - ENGLISH
Chapter 1 Preparation - Precautions for use
Within 30°
Within 15°
Within 15°
Within 30°
Cautions when setting the projectors
f Use the adjustable feet only for the oor standing installation and for adjusting the angle. Using them for other
purposes may damage the projector.
f When installing the projector with a method other than the oor installation using the adjustable feet or the
ceiling installation, use the four screw holes for ceiling mount (as shown in the gure) to x the projector to the
mount. For details about the screw hole position for ceiling mount, refer to “Screw hole specications for ceiling
mount” (x page 132).
(Screw diameter: M4, tapping depth inside the projector: 8 mm (5/16"), torque: 1.25 ± 0.2 N·m)
In such case, make sure that there is no clearance between the screw holes for ceiling mount on the projector
bottom and the setting surface by inserting spacers (metallic).
Screw holes for ceiling mount
(M4)
Adjustable feet
Positions of screw holes for ceiling mount
and adjustable feet
f Do not stack the projectors.
f Do not use the projector supported by its top.
f Do not block the ventilation ports (intake and exhaust) of the projector.
f Avoid heating and cooling air from the air conditioning system directly blow to the ventilation ports (intake and
exhaust) of the projector.
over 500 mm
(19-11/16")
over 1 000 mm
(39-3/8")
over 500 mm
(19-11/16")
over 200 mm
(7-7/8")
ENGLISH - 17
Chapter 1 Preparation - Precautions for use
f Do not install the projector in a conned space.
When placing the projector in a conned space, a ventilation and/or air conditioning system is required. Exhaust
heat may accumulate when the ventilation is not enough, triggering the protection circuit of the projector.
f Panasonic takes no responsibility for any damage to the product caused by an inappropriate choice of location
for installing the projector, even if the warranty period of the product has not expired.
Security
When using this product, take safety measures against the following incidents.
f Personal information being leaked via this product
f Unauthorized operation of this product by a malicious third party
f Interfering or stopping of this product by a malicious third party
Take sufcient security measures.
f Make your password as difcult to guess as possible.
f Change your password periodically. The password can be set in the [SECURITY] menu → [PASSWORD
CHANGE].
f Panasonic Corporation or its afliate company never inquires a password directly to a customer. Do not tell your
password in case you receive such an inquiry.
f The connecting network must be secured by rewall or others.
f Set a password for web control function appropriately and restrict the users who can log in. The password for
the web control function can be set on the [Change password] page of the web control screen.
Early Warning Software
The projector supports “Early Warning Software”, which monitors the status of the display devices (projector or
at panel display) and the peripheral devices inside an intranet, and noties of abnormality of such equipment and
detects signs of possible abnormality. Also, maintenance can be performed in advance, because this software
gives notication of approximate time to replace consumables of the display, to clean each part of the display, and
to replace the components of the display.
Depending on the type of license, the number of displays that can be registered for monitoring varies. Limited
to the rst 90 days after installation in a computer, it is possible to register up to 2048 units of displays free of
charge.
Download the software from the Panasonic website (https://panasonic.net/cns/projector/pass/). It is necessary to
register and login to PASS*1 to download.
*1 PASS: Panasonic Professional Display and Projector Technical Support Website
Visit the Panasonic website (https://panasonic.net/cns/projector/pass/) for details.
Storage
When storing the projector, keep it in a dry room.
Disposal
To dispose of the product, ask your local authorities or dealer for correct methods of disposal.
The luminous lamp contains mercury. When disposing of used lamp units, contact your local authorities or dealer
for correct methods of disposal.
18 - ENGLISH
Chapter 1 Preparation - Precautions for use
Cautions on use
r To get a good picture quality
In order to view a beautiful image in higher contrast, prepare an appropriate environment. Draw curtains or blinds
over windows and turn off any lights near the screen to prevent outside light or light from indoor lamps from
shining onto the screen.
r Do not touch the surface of the projector lens with your bare hands.
If the surface of the lens becomes dirty from ngerprints or anything else, this will be magnied and projected onto
the screen.
It is recommended to attach the supplied lens cap to the projection lens when you do not use the projector.
r LCD panel
The LCD panel is precision-made. Note that in rare cases, pixels could be missing or always lit. Note that such
phenomena do not indicate malfunction.
If still images are projected for a long time, a residual image may remain on the LCD panel. In this case, project
the all white screen for over an hour. Note that the residual image may not disappear.
r Optical parts
When the operating environment temperature is high or in environments where lots of dust, cigarette smoke, etc.
is present, the replacement cycle of the LCD panel, polarizing plate and other optical parts may be shorter even if
used for less than one year. Consult your dealer for details.
r Luminous lamp
The light source of the projector is a high-pressure mercury lamp.
A high-pressure mercury lamp has the following characteristics.
f The luminance of the luminous lamp will decrease by duration of usage.
f The luminous lamp may burst with a loud sound or have its service life shortened because of shock, chipping, or
degradation due to cumulative runtime.
f The luminous lamp life varies greatly depending on individual differences and usage conditions. In particular,
continuous use for 12 hours or more and frequent off/on switching of the power greatly deteriorate the luminous
lamp and affect the luminous lamp life.
f In rare cases, the luminous lamp burst shortly after the projection.
f The risk of bursting increases when the luminous lamp is used beyond its replacement cycle. Make sure to
replace the lamp unit according to the proper replacement time (“When to replace the lamp unit”
(Æ page 114) and “How to replace the lamp unit” (Æ page 115))
f If the luminous lamp bursts, gas contained inside of the luminous lamp is released in a form of smoke.
f It is recommended to store replacement lamps for contingency.
r Computer and external device connections
When connecting a computer or an external device, read this manual carefully regarding the use of power cords
and shielded cables as well.
ENGLISH - 19
Chapter 1 Preparation - Precautions for use
Accessories
Make sure the following accessories are provided with your projector. Numbers enclosed < > show the number of
accessories.
Wireless remote control unit <1>
(N2QAYA000088)
Power cord
CD-ROM <1>
(1JK1VZ580)
AAA/R03 or AAA/LR03 battery <2>
(TXFSX02UXRZ)
(TXFSX02UYAZ) String <1>
(6103504711)
(for remote control unit)
(TXFSX02UFEZ)
Lens cap <1>
(TKKL5573) (TKKL5577)
(For PT-VZ580) (For PT-VW540 and
PT-VX610)
RGB signal cable <1>
(K1HY15YY0012)
(Attached to the projector at the time of purchase)
Attention
f After unpacking the projector, discard the power cord cap and packaging material properly.
f Do not use the supplied power cord for devices other than this projector.
f For lost accessories, consult your dealer.
f Store small parts in an appropriate manner, and keep them away from young children.
(for lens cap)
Note
f The type and number of the power cord depend on the country in which you purchased the product.
f The model numbers of accessories are subject to change without prior notice.
20 - ENGLISH
Chapter 1 Preparation - Precautions for use
Contents of the supplied CD-ROM
The contents of the supplied CD-ROM are as follow.
Operating Instructions
Operating Instructions – Multi Monitoring & Control Software
Instruction / list (PDF)
Software
Operating Instructions – Logo Transfer Software
List of Compatible Device
Models
Multi Monitoring & Control
Software (Windows)
Logo Transfer Software
(Windows)
This is a list of projectors that are compatible with the software contained
in the CD-ROM and their restrictions.
This software allows you to monitor and control multiple displays
(projector or at panel display) connected to the LAN.
This software allows you to transfer original images, such as company
logos to be displayed when projection starts, to the projector.
Note
f The “List of Compatible Device Models” for the at panel display compatible with the “Multi Monitoring & Control Software” can be
downloaded from the Panasonic website (https://panasonic.net/cns/prodisplays/).
Optional accessories
Options Model No.
Ceiling Mount Bracket
Replacement Lamp Unit ET-LAV400
Replacement Filter Unit ET-RFV410
Early Warning Software
(Basic license/3-year license)
*1: The sufx of the Model No. differs according to the license type.
ET-PKL100H (for high ceilings), ET-PKL100S (for low ceilings),
ET-PKV400B (Projector Mount Bracket)
ET-SWA100 Series*
Note
f The model numbers of optional accessories are subject to change without prior notice.
1
ENGLISH - 21
Chapter 1 Preparation - About your projector
About your projector
Remote control
Front
1
2
3
4
5
6
1 Remote control signal transmitter
2 Power <v/b> button (v standby / b power on)
Sets the projector to the state where the projector is switched
off (standby mode). Also starts projection when the power is
switched off (standby mode).
3 Input selection buttons (<COMPUTER 1> / <COMPUTER 2> /
<VIDEO> / <HDMI 1> / <HDMI 2>)
Switches the input signal to project. (Æ page 44)
4 <MENU> button / <RETURN> button / asqw buttons
<ENTER> button
Used to operate the menu screen. (Æ page 53)
The asqw buttons are also used to enter password or
characters for [SECURITY].
5 <FREEZE> button
Pauses the projected image and mute the audio temporarily.
(Æ page 49)
6 Number (<1> - <6>) buttons
Used for entering an ID number in a multiple projector
environment or a password.
7 <AUTO SETUP> button
Used to perform automatic adjustment while projecting the
image. (Æ page 49)
8 <MUTE> button
Used to temporarily mute the projector. (Æ page 48)
7
8
9
/
10
11
14
15
12
13
9 <AV MUTE> button
Used to turn off the audio and video temporarily. (Æ page 48)
10 <FUNCTION> button
Assigns a frequently used operation as a shortcut button.
(Æ page 50)
11 <DEFAULT> button
Resets the content of the sub-menu to the factory default.
(Æ page 54)
12 <D.ZOOM +> button / <D.ZOOM -> button
Zooms in and out the images. (Æ page 50)
13 <VOL +> button / <VOL -> button
Adjusts the volume level of the built-in speaker or the audio
output. (Æ page 48)
14 <ID SET> button
Sets the ID number of the remote control in a multiple projector
environment. (Æ page 26)
15 <ID ALL> button
Used to simultaneously control all the projectors with one
remote control when using multiple projectors. (Æ page 26)
16 <P-TIMER> button
Operates the presentation timer function. (Æ page 51)
17 <SCREEN ADJ> button
Corrects the distortion of the projected image.
(Æ page 49)
16
17
22 - ENGLISH
Chapter 1 Preparation - About your projector
Attention
f Do not drop the remote control.
f Avoid contact with liquids.
f Do not attempt to modify or disassemble the remote control.
f Please observe the following contents that are described on the back of the remote control unit (see the picture below).
g Do not use a new battery together with an old battery.
g Do not use unspecied batteries.
g Make sure the polarities (+ and -) are correct when inserting the batteries.
In addition, please read the contents that are related to batteries in the "Read this rst!".
1.Do not use old battery with new one.
2.Do not use batteries other than the
type specified.
3.Be sure the batteries are inserted properly.
Caution label at the back of the remote control
Note
f The remote control can be used within a distance of about 7 m (22′11-5/8″) if pointed directly at the remote control signal receiver. The
remote control can control at angles of up to ± 30 ° vertically and ± 30 ° horizontally, but the effective control range may be reduced.
f If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate correctly.
f You can operate the projector by reecting the remote control signal on the screen. The operating range may differ due to the loss of light
caused by the properties of the screen.
f When the remote control signal receiver is lit with a uorescent light or other strong light source, the projector may become inoperative. Set
the projector as far from the luminous source as possible.
Projector body
Front Side
1 2 3
4 5
Rear
6 76
Projection direction
10 118 9
4
WARNING
Keep your hands and other objects away from the air exhaust
port.
f Keep your hands and face away.
f Do not insert your ngers.
f Keep heat-sensitive objects away.
Heated air from the air exhaust port can cause burns, injury, or
deformations.
1 Remote control signal receiver
2 Focus Lever
Adjusts the focus.
3 Zoom Lever
Adjusts the zoom.
66
12 13
4 Adjustable feet
Adjusts the projection angle.
5 Projection Lens
6 Air exhaust port
7 Speaker
8 <AC IN> terminal
Connects the supplied power cord.
9 Security slot
This security slot is compatible with the Kensington security
cables.
10 Burglar hook port
Attaches a burglar prevention cable, etc.
11 Connecting terminals (Æ page 25)
12 Air lter cover
The air lter unit is inside.
13 Air intake port
ENGLISH - 23
Chapter 1 Preparation - About your projector
r To p
: Projection direction
1 Vertical lens shift dial
Adjusts the projecting position in the vertical direction (vertical
shift).
2 Control panel and Indicators (Æ page 24)
3 Lamp cover
The luminous lamp is inside.
1
2 3
r Bottom
4 Air exhaust port
5 Burglar hook port
Attaches a burglar prevention cable, etc.
4
5
Attention
f Do not block the ventilation ports (intake and exhaust) of the projector.
r Control panel and Indicators
1
2
3
4
5
6
7
1 Power button <v/b> (v Standby / b Power on)
Sets the projector to the state where the projector is switched
off (standby mode). Also starts projection when the power is
switched off (standby mode).
2 Power indicator <ON(G)/STANDBY(R)>
Displays the status of the power.
3 Lamp indicator <LAMP>
Displays the status of the luminous lamp.
4 Temperature indicator <TEMP>
Displays the status of the internal temperature.
5 Ambient luminance sensor (Æ page 59)
6 <MENU> button
Displays or hides the main menu. (Æ page 53)
When the sub menu is displayed, pressing it will return to the
previous screen.
8
9
10
7 <ENTER> button
Determines and executes an item in the menu screen.
8 <INPUT SELECT> button
Switches the input signal to project. (Æ page 44)
9 asqw buttons
Used to select the menu screen items, switch the setting or
adjust the level.
Also used to enter a password in the [SECURITY] menu or enter
characters.
10 <AUTO SETUP> button
Used to automatically adjust with auto setup function while
projecting the image. (Æ page 49)
24 - ENGLISH
r Connecting terminals
1 2 3 4 5
Chapter 1 Preparation - About your projector
6 7 8
1 <COMPUTER 2 IN/1 OUT> terminal
This is the terminal to input RGB signals or YCBCR/YPBPR signals.
It can also output the signals input from <COMPUTER 1 IN>
terminal to an external device.
2 <COMPUTER 1 IN> terminal
This is the terminal to input RGB signals or YCBCR/YPBPR signals.
3 <HDMI 1 IN> terminal / <HDMI 2 IN> terminal
These are the terminals to input HDMI signal.
4 <DC OUT> terminal
This is the USB terminal only used for power supply (DC 5 V,
maximum 2 A).
This can be used when a power is needed to be supplied to a
wireless display adaptor, etc.
5 <LAN> terminal
This is the LAN terminal to connect to the network.
6 <SERIAL IN> terminal
This is the RS-232C compatible terminal to externally control the
projector by connecting a computer.
7 <VIDEO IN> terminal
This is the terminal to input video signals.
8 <AUDIO IN 3> terminal
This is the terminal to input audio signals.
Left input <L> and right input <R> are provided for the <AUDIO
IN 3> terminal.
9 <AUDIO IN 1> terminal / <AUDIO IN 2> terminal
These are the terminals to input audio signals.
10 <VARIABLE AUDIO OUT> terminal
This is the terminal to output the input audio signal.
9
Attention
f When a LAN cable is directly connected to the projector, the network connection must be made indoors.
10
ENGLISH - 25
Chapter 1 Preparation - Preparing the remote control
Preparing the remote control
Inserting and removing batteries
Fig. 1
1) Open the cover. (Fig. 1)
2) Insert batteries and close the cover (insert the "m" side first). (Fig. 2)
f When removing the batteries, perform the steps in reverse order.
Fig. 2
When using the system with multiple projectors
When you use the system with multiple projectors, you can operate all the projectors simultaneously or each
projector individually by using single remote control, if a unique ID number is assigned to each projector.
When you want to set the ID number, at rst you need to complete the Initial setting, and then after setting the ID
number of the projector, set the ID number on the remote control. About Initial setting, please refer to “When the
initial setting screen is displayed” (x page 40).
The factory default ID number of the unit (the projector and the remote control) is set to [ALL], you can control with
this setting. If necessary, please set the ID number to the remote control and the projector. About how to set the ID
number of the remote control, please refer to “Setting the ID number of the remote control” (x page 51).
Note
f Set the ID number of the projector from the [PROJECTOR SETUP] menu → [PROJECTOR ID].
26 - ENGLISH
Chapter 1 Preparation - Attaching the lens cap
Attaching the lens cap
When moving this projector or while not using it over an extended period of time, it is recommended to attach the
lens cap to avoid contaminating the lens.
To prevent loss of the lens cap, please attach the lens cap with the string of accessories according to the following
procedures.
1) Thread the thinner end of the string through the hole on the lens cap.
Lens cap
String
2) Thread the other side (the side with larger ring) of the string through the hole at the bottom of the
projector and fasten it.
ENGLISH - 27
Chapter 2 Getting Started
This chapter describes things you need to do before using the projector such as the setup and
connections.
28 - ENGLISH
Chapter 2 Getting Started - Setting up
Setting up
Installation mode
There are four ways to set up the projector. Set the [PROJECTOR SETUP] menu → [PROJECTION METHOD]
(x page 79) depending on the installation mode.
Setting on a desk/oor and projecting forward Setting on a desk/oor and projecting from rear
(Using the translucent screen)
Menu item Method Menu item Method
[PROJECTION METHOD]
Mounting on the ceiling and projecting forward Mounting on the ceiling and projecting from rear
[AUTO] or [FRONT/DESK]
[PROJECTION METHOD]
(Using the translucent screen)
[REAR/DESK]
Menu item Method Menu item Method
[PROJECTION METHOD]
[AUTO] or [FRONT/CEILING]
[PROJECTION METHOD]
[REAR/CEILING]
Note
f The projector has a built-in angle sensor. The attitude of the projector is automatically detected by setting the [PROJECTOR SETUP] menu
→ [PROJECTION METHOD] to [AUTO]. For rear projection, set the [PROJECTION METHOD] to [REAR/DESK] or [REAR/CEILING].
r Angle sensor
The range of installation posture detected by the projector’s built-in angle sensor is as follows.
In case of [AUTO], when the projector is placed with the top side upward within ±30° from the horizontal plane, it
will switch to [FRONT/DESK] automatically; when the projector is placed with the top side downward within ±30°
from the horizontal plane, it will switch to [FRONT/CEILING] automatically. Although it is detected as [FRONT/
DESK] even when it exceeds ±30° with respect to the horizontal plane, do not use such installation posture in this
range.
Installation
prohibited posture
[FRONT/DESK]
30°
30°
30°
30°
[FRONT/CEILING]
Installation
prohibited posture
Projection direction
:
ENGLISH - 29
Chapter 2 Getting Started - Setting up
Attention
f The angle sensor cannot detect whether it is the “Installation prohibited posture” in the above gure. Do not use the projector tilted at an
angle that exceeds ±30° from the horizontal plane. It may reduce the life of the components. (x page 16)
Parts for ceiling mount (optional)
This requires an optional ceiling mount bracket. Be sure to use the Projector Mount Bracket together with the
ceiling mount bracket for high ceilings or low ceilings.
Model No.:
① ET-PKL100H (for high ceilings), ET-PKV400B (Projector Mount Bracket)
② ET-PKL100S (for low ceilings), ET-PKV400B (Projector Mount Bracket)
f Use only the ceiling mount brackets specied for this projector.
f Refer to the Installation Instructions for the ceiling mount bracket when you install the bracket and the projector.
Attention
f To ensure projector performance and security, installation of the ceiling mount bracket must be carried out by your dealer or a qualied
technician.
Screen size and throw distance
Refer to the screen size and projection distances to install the projector. Image size and image position can be
adjusted in accordance with the screen size and screen position.
f Following illustration is prepared on the assumption that the projected image size and position have been
aligned to t full in the screen.
Projected image
SD
SW
SW SH
Projection distance
L (LW/LT) *
*1 LW : Minimum distance
LT : Maximum distance
1
SH Image height
SW Image width
H Distance from the center of lens to the image lower end
SD Projected image size
SH
Attention
f Before installing, please read “Precautions for Use”. (Æ page 16)
Screen
L (LW/LT)
H
L (LW/LT)
Screen
(Unit: m)
30 - ENGLISH
Loading...