Panasonic PT-D12000 User Manual
< 1 >
S PEC F ILE
Product Number : PT-D12000
Product Name : 3-Chip DLP™ Projector
As of July 2008. Appearance and specifications are subject to change without notice.
S PEC F ILE
PT-D12000
3-Chip DLP™ Projector
As of July 2008 < 2 >
Specifications
Main Unit
Power supply: North America:
Europe, Asia
Power consumption: North America:
Europe, Asia
DLP™ chip: Panel size:
Display method:
Pixels:
Lens:
Lamp:
Screen size:
Brightness*
1
:
Center-to-corner uniformity*1:
Contrast*1:
Resolution:
Scanning frequency: RGB:
YPBPR (YCBCR):
S-Video/Video:
Optical axis shift*3: Vertical:
Horizontal:
Keystone correction range:
Installation:
Terminals: DVI-D IN:
RGB1 IN:
R, G, B:
Y, P B, PR
120–240 V AC, 16–9.0 A, 50/60 Hz (3-wire single-phase)
220–240 V AC, 9.5 A, 50/60 Hz (3-wire single-phase)
1,600–1,500 W (10-15 W in standby mode with fan stopped)
1,500 W (15 W in standby mode with fan stopped)
0.95˝ diagonal (4:3 aspect ratio)
DLP™ chip x 3 (R, G, B), DLP™ projection system
1,470,000 (1,400 x 1,050) x 3, total of 4,410,000 pixels
Optional powered zoom/focus lenses
300 W UHM™ lamp x 4
70– 600 inches, 4:3 aspect ratio
(70 – 300 inches with the ET-D75LE5, 4:3 aspect ratio)
12,000 lumens (four-lamp operation mode)
90%
5,000:1 (full on/full off, in dynamic iris 3 mode)
1,400 x 1,050 pixels (Input signals that exceed this resolution will be
converted to 1,400 x 1,050 pixels.)
Horizontal: 15–100 kHz, Vertical: 24–120 Hz*
2
,
Dot clock: 20–162 MHz
480i: fH 15.75 kHz; fV 60 Hz, 576i: fH 15.63 kHz; fV 50 Hz,
480p: fH 31.50 kHz; fV 60 Hz, 576p: fH 31.25 kHz; fV 50 Hz,
720/60p: fH 45.00 kHz; fV 60 Hz, 720/50p: fH 37.50 kHz; fV 50 Hz,
1035/60i: fH 33.75 kHz; fV 60 Hz, 1080/60i: fH 33.75 kHz; fV 60 Hz,
1080/50i: fH 28.13 kHz; fV 50 Hz, 1080/25p: fH 28.13 kHz; fV 25 Hz,
1080/24p: fH 27.00 kHz; fV 24 Hz, 1080/24sF: fH 27.00 kHz; fV 48 Hz,
1080/30p: fH 33.75 kHz; fV 30 Hz, 1080/60p: fH 67.50 kHz; fV 60 Hz,
1080/50p: fH 56.25 kHz; fV 50 Hz
Horizontal: 15.75/15.63 kHz, Vertical: 50/60 Hz,
(NTSC, NTSC4.43, PAL, PAL60, PAL-N, PAL-M, SECAM)
±50% (±40% with the ET-D75LE6) from center of screen, powered
±30% (±20% with the ET-D75LE6) from center of screen, powered
Vertical: ±40° (±22° with the ET-D75LE5, ±28° wih the ET-D75LE6),
with geometric adjustment: vertical ±10°, horizontal ±15°
Ceiling/floor, front/rear
DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, compati-
ble with single link only,
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p,
1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p
VGA (640 x 480) – WUXGA*4(1,920 x 1,200), compatible with non-
interlaced signals only, dot clock: 25–162 MHz
BNC x 5
G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms,
B, R: 0.7 Vp-p, 75 ohms
HD, VD, SYNC: 1.4–5.0 Vp-p, positive/negative automatic
Y: 1.0 p-p, 75 ohms (incl. sync signal), PB/PR: 0.7 Vp-p, 75 ohms
0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms
NOTE: HD/SYNC, and VD terminals do not accept 3-value direct sync signals.
S PEC F ILE
PT-D12000
3-Chip DLP™ Projector
As of July 2008 < 3 >
RGB2 IN:
R, G, B:
Y, P
B, PR
VIDEO IN:
VIDEO OUT:
S-VIDEO IN:
LAN:
SERIAL IN*5:
SERIAL OUT*5:
REMOTE 1 IN:
REMOTE 1 OUT:
REMOTE 2 IN:
Optional board slot*6:
With ET-MD77SD1 installed: SERIAL IN:
SERIAL OUT:
With ET-MD77SD3 installed: SERIAL IN:
SERIAL OUT:
With ET-MD100SD4 installed: Link A/Link B IN:
With ET-MD77DV installed: DVI-D IN:
Power cord:
Cabinet material:
Dimensions (W x H x D):
Weight*7:
D-sub HD 15-pin x 1
0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms
HD, VD, SYNC: TTL, high impedance, positive/negative automatic
VD: 1.4–5.0 Vp-p, positive/negative automatic, 75 ohms
Y: 1.0 p-p, 75 ohms (incl. sync signal), PB/PR: 0.7 Vp-p, 75 ohms
NOTE: HD/SYNC, and VD terminals do not accept 3-value direct sync signals.
BNC x 1, 1.0 Vp-p, 75 ohms
BNC x 1, 1.0 Vp-p, active through
Mini DIN 4-pin x 1
Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms (S1 signal compatible)
RJ-45 x 1, 10Base-T/100Base-TX, compatible with PJLink™ (class 1)
D-sub 9-pin (female) x 2, for external control (RS-232C/RS-422 compli-
ant)
D-sub 9-pin (male) x 1, for link control
M3 jack x 1 for wired remote control
M3 jack x 1 for link control
D-sub 9-pin x 1 for external control (parallel)
BNC x 1, SD-SDI signal (YCBCR 4:2:2 10-bit):
SMPTE 259M compliant: 480i, 576i
BNC x 1, active through
BNC x 1
SD-SDI signal (YCBCR 4:2:2 10-bit):
SMPTE 259M compliant: 480i, 576i
Single-link HD-SDI signal (YCBCR 4:2:2 10-bit):
SMPTE 292M compliant: 720/50p, 720/60p, 1035/60i, 1080/50i,
1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
BNC x 1, active through
BNC x 1 for each
SD-SDI signal (YCBCR 4:2:2 10-bit):
SMPTE 259M compliant: 480i, 576i
Single-link HD-SDI signal (YCBCR 4:2:2 10-bit):
SMPTE 292M compiant: 720/50p, 720/60p, 1080/50i, 1080/60i,
1080/25p, 1080/24p, 1080/24sF, 1080/30p
Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit):
SMPTE 372M compiant: 1920 x 1080/50i, 1920 x 1080/60i, 1920 x
1080/25p, 1920 x 1080/24p, 1920 x 1080/24sF, 1920 x 1080/30p
Dual-link HD-SDI signal (X´Y´Z´ 4:4:4 12-bit):
2048 x 1080/24p, 2048 x 1080/24sF
DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, compati-
ble with single link only,
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p,
1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p
VGA (640 x 480) – WUXGA*4(1,920 x 1,200), compatible with non-
interlaced signals only, dot clock: 25–162 MHz
3 m/9.8´
Moulded plastic
578 x 320 x 643 mm (22-3/4˝ x 12-19/32˝ x 25-5/16˝) (without lens)
Approx. 35 kg (77.2 lbs) (without lens)
S PEC F ILE
PT-D12000
3-Chip DLP™ Projector
As of July 2008 < 4 >
Weights and dimensions shown are approximate. Specifications subject to change without notice.
*1 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*2 Smooth image reproduction may not be possible when a motion video signal with a vertical frequency other than 50 or 60 Hz is input.
*3 Shift range is limited during simultaneous horizontal and vertical shifting.
*4 WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
*5 Contact your dealers for details when the control using RS-232C or RS-422 is required.
*6 The LAN terminal on the optional board will be inactivated after installation. Use the LAN terminal on the main unit.
*7 Average value. May differ depending on models.
*8 The operating temperature range is 0°C (32°F) to 40°C (104°F) when used in High-Altitude mode (1,400 m [4,593 feet] to 2,700 m [8,858 feet]).
Also, if the ambient temperature exceeds 40°C (104°F) (35°C [95°F] in High-Altitude mode) when using all four lamps, the light output may be
reduced approximately 30% to protect the projector.
*9 Operation range differs depending on environments.
Operating temperature*8:
Operating humidity:
Remote Control Unit
Number of functions:
Power supply:
Operation range*9:
Dimensions (W x H x D):
Weight:
Supplied Accessories
Optional Accessories
Zoom lens (0.9 –1.1:1):
Zoom lens (1.4 –1.8:1):
Zoom lens (1.8 – 2.8:1):
Zoom lens (2.8– 4.6:1):
Zoom lens (4.6–7.4:1):
Zoom lens (7.3–13.8:1):
Fixed-focus lens (0.7:1):
SD-SDI board:
HD/SD-SDI board:
Dual link HD-SDI board:
DVI-D board:
Replacement lamp unit
Ceiling mount bracket for high ceilings
Ceiling mount bracket for low ceilings
Frame
Carrying handle
Smoke cut filter
0°C–45°C (32°F–113°F)
10%–80% (no condensation)
35 keys, 39 functions
3 V DC (AA battery x 2)
Approx. 30 m (98.4´) when operated from directly signal receptor
51 x 22.7 x 176 mm (2˝ x 7/8˝ x 6-15/16˝)
134 g (4.7 oz) (including batteries)
Power cord
Wireless/wired remote control unit
Batteries for remote control (x 2)
Eye bolts (x 4)
Wire rope
ET-D75LE6
ET-D75LE1
ET-D75LE2
ET-D75LE3
ET-D75LE4
ET-D75LE8
ET-D75LE5
ET-MD77SD1
ET-MD77SD3
ET-MD100SD4
ET-MD77DV
ET-LAD12K (one unit)
ET-LAD12KF (a set of four lamps)
ET-PKD100H
ET-PKD100S
ET-PFD100
ET-HAD100
ET-SFD100
Loading...