81-IN3034-9922Manufactured by:
Before attempting to connect or operate this product, please read these instructions completely.
for
MODEL: Indoor Wall/Corner/Ceiling Housings
PMWH8, PMCH8
STANDARD INSTALLATION PROCEDURE
INCLUDES MODELS: PMWH8, PMCH8
NOTE: Max. storage space is 8”
(Panasonic 1/3” Camera Class with
Panasonic Fixed Focal Lens Series)
1. Remove contents from carton and open lid of the unit with barrel
lock key.
Figure 1
2. To access inside of the unit during mounting and adjusting the lid
can be temporarily propped open by using a screwdriver or similar
object in the manner shown in
3. Position unit in desired location and mark spots of the four
mounting holes. For best results, use the actual housing to obtain
placements of mounting holes. The hole location diagrams are
for general references only.
4. Prepare spots marked on mounting surfaces as required by
applicable building codes before mounting the unit.
5. Pass electrical and video cables through the access hole on back
of the unit, or use any of the knockout hole(s), then secure unit in
place with appropriate hardware.
6. Complete electrical and video connections with camera before
attaching camera to camera bracket with the hex bolt.
Use with Class 2 power supply only.
7. To achieve desired camera position, adjust hex bolt and slotted
screw with proper tools.
which the camera & the bracket can be maneuvered.
lens of the camera as close to viewing window as possible so as
to provide adequate room in the back for cables & connectors. In
addition, the use of a right angle coax connector is strongly
recommended as it greatly reduces strain on coax cable connection
with camera.
8. After tightening all fasteners close and lock the lid to complete the
installation.
Note
: key is removable only when lid is locked; see
.
Figure 2
Figure 3
.
shows the three directions in
Note
Note
!
: place
PRODUCT INSTRUCTIONS
Lock and
remove key
Open
FIG. 1
FIG. 2
:
FIG. 3
DO NOT EXPOSE ENCLOSURE TO RAIN OR MOISTURE
PARTS LIST
G
G
E
E
F
F
C
C
B
B
M
M
L
L
H
H
J
J
D
D
K
K
N
N
A
A
PMCH8
Description Part Number Qty
A PMCH8 Housing w/ Lid 50-VL-1466 1
B Viewing Window 27-WDNMS 1
C Window Shield 27-SHNMS 1
D AMS Camera Bracket 30-VL-1452 1
E AMS Barrel Lock 95-FSLK02 1
F AMS Barrel Lock Cam 95-FSCM01 1
G AMS Barrel Lock Key 95-FSKY04 2
H 1/4-20X1/2 Hex Bolt 90-BTHH32 1
I 1/4-2X1/2 Slotted Screw 90-BTHH04 1
J 1/4 SAE Flat Washer 92-WSFL01 1
K 1/4 Split Lock Washer 92-WSSL01 2
L #6 Hex Nut 91-NTHH04 6
I
M #6 Star Washer 92-WSTH01 6
N O-Ring 96-RSORNG 1
Description Part Number Qty
PMWH8
A PMWH8 Housing w/ Lid 50-VL-1467 1
B Viewing Window 27-WDNMS 1
C Window Shield 27-SHNMS 1
D AMS Camera Bracket 30-VL-1452 1
E AMS Barrel Lock 95-FSLK02 1
F AMS Barrel Lock Cam 95-FSCM01 1
G AMS Barrel Lock Key 95-FSKY04 2
H 1/4-20X1/2 Hex Bolt 90-BTHH32 1
I 1/4-2X1/2 Slotted Screw 90-BTHH04 1
J 1/4 SAE Flat Washer 92-WSFL01 1
K 1/4 Split Lock Washer 92-WSSL01 2
L #6 Hex Nut 91-NTHH04 6
M #6 Star Washer 92-WSTH01 6
I
N O-Ring 96-RSORNG 1
General Dimensions / Mounting Hole & Cable Access Hole Location Diagrams
PMCH8
5.50"
2.23"
56.7mm
3.30"
83.7mm
8.50"
215.9mm
2.38"
60.3mm
3.25"
8.25"
82.6mm
209.6mm
.25"*
6.4mm*
Mounting Hole (4)
(FOR REFERENCE USE ONLY AS ACTUAL DIMENSIONS MAY VARY SLIGHTLY FROM UNIT TO UNIT)
5.50"
139.7mm
.88"*
22.2mm*
Knockout
Hole (2)
1.50"
38.1mm
.63"*
15.9mm*
Open Hole (1)
* INDICATES
DIAMETER OF
HOLE OR
KNOCKOUT
2.50"
63.5mm
8.50"
215.9mm
139.7mm
8.25"
209.6mm
.25"*
6.4mm*
Mounting Hole (4)
2.00"
50.8mm
3.00"
76.2mm
PMWH8
22.2mm*
Knockout
3.25"
82.6mm
.88"*
Hole (1)
1.50"
38.1mm
.63"*
15.9mm*
Open Hole (1)
2.50"
63.5mm