Panasonic PM-64 Series INSTRUCTION MANUAL

INSTRUCTION MANUAL

Photoelectric Sensor

Built-in U-shaped Micro-photosensor

PM-64 Series

Thank you very much for using SUNX products. Please
read this Instruction Manual carefully and thoroughly for
the correct and optimum use of this product. Kindly keep
this manual in a convenient place for quick reference.

WARNING

٨

Never use this product as a sensing device for per­sonnel protection.

٨

In case of using sensing devices for personnel pro­tection, use products which meet laws and stand­ards, such as OSHA, ANSI or IEC etc., for person­nel protection applicable in each region or country.

٨

Since protection circuit against output short-circuit
or reverse polarity connection is not incorporated,
make sure to wire correctly. Also, ensure to insulate
the unused output wire.
Take care that wrong wiring will damage the sensor.

1

I/O CIRCUIT DIAGRAM

NPN output type

Main circuit

Internal circuit Users' circuit

PNP output type

Main circuit

Internal circuit Users' circuit

Note: PNP output type is not available for the PM-T64W type.

2

CAUTIONS

This product has been developed / produced for in-

٨

dustrial use only.

٨

Since the sensor is intended for use inside ma­chines, no special countermeasures have been tak­en against extraneous light. Please take care that
extraneous light is not directly incident on the beam
receiving section.

٨

If the sensor is used in a place having excessive
dust, periodically clean the emitting and receiving
sections with a dry, soft cloth.

٨

Do not use during the initial transient time (50ms) af­ter the power supply is switched on.

Color code of optional connector attached cable

Brown) +V

(

50mA max.

1

t

50mA max.

u

t2

L

Load

0mA max.

5

50mA max

oad

L

Load

.

oad

+

5to24VDC
r10%

-

* Output operation
Output 1: Light-ON
Output 2: Dark-ON

+

5to24VDC
r10%

-

* Output operation
Output 1: Light-ON
Output 2: Dark-ON

(Black) Output 1

(White) Output2

(Blue) 0V

Color code of optional connector attached cable

(Brown) +V

k) Outpu

(Bla

c

i

te) Outp

(Wh

(Blue) 0V

٨Cable extension is possible up to an overall length of

100m with a 0.3mm
a voltage drop shall occur due to the cable exten­sion, ensure that the power supply voltage at the end
of the cable attached to the sensor or at the sensor
terminals is within the rating.

Connector
attached cable

But, when the overall ca­ble length, including the
cable attached to the
sensor,isasgivenbe­low, there is no need to
confirm the voltage.

٨

If there is a large surge generating equipment, such
as, motor, solenoid, electromagnetic valve, etc., in
the vicinity of the micro-photosensor, use a surge ab­sorber on that equipment. Further, do not run the
sensor cables along power lines and use a capacitor
between +V and 0V, if required. Use the sensor after
confirming that the surge has been eliminated.
In case the sensor is fixed

٨

with screws, strictly ob­serve the conditions descri­bedintherightdiagram.

Note: If the product is used at an ambient temperature of 50 or

more, make sure to mount it on a metallic body.

3

WIRING

Connection method

٨ Insert the cable with connec-

tor (CN-14A-Cغ) in the con­nector part of this product as
shown in the right figure.

<Connector pin position>

ԘԙԚԛ

2

, or more, cable. However, since

Overall length: 100m

+V

Extension cable

Output

0V

Supply voltage: 4.5V or more

Wire conductor

Connector pin No.
Terminal designation

cross-section area

0.08 to 0.1mm

Tightening torque

+VԘOutput 1 Output 2

2

2

0.2mm

2

0.3mm

Screw M3

Washe r

CN-14A-Cغ

<Mating connector>

Housing: PAP-04V-S

Manufactured by J.S.T. MFG
CO., LTD.

ԙԚ0Vԛ

+

5to24VDC
r10%

-

Overall cable
length

Up to 5m
Up to 10m
Up to 20m

0.5N㨯morless
Ǿ6mm

(small diameter type)

Projection

Disconnection method

٨ Pressing the projection of the cable with connector,

pull out the connector.

Note: Take care that if the cable is pulled out without pressing the

projection, the cable may break.

4

INTENDED PRODUCTS FOR CE MARKING

٨The models listed under 'Catalogue' come

with CE Marking.
As for all other models, please contact our
office.

SUNX Limited

Overseas Sales Dept. (Head Office)

2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan
Phone: [phone] FAX: [phone]

Europe Headquarter: Panasonic Electric Works Europe AG

Rudolf-Diesel-Ring 2, D-83607 Holzkirchen, Germany
Phone: [phone]

US Headquarter: Panasonic Electric Works Corporation of America

629 Central Avenue New Providence, New Jersey 07974 USA
Phone: [phone]

URL : sunx.com

PRINTED IN JAPAN