Manufactured by:
81-IN3045.9924
Before attempting to connect or operate this product, please read these instructions completely.
for
MODEL: Wall Mount Bracket
PBWM10
WALL MOUNT INSTRUCTIONS:
1. Start the installation by removing the access cover, this is done
by loosening the (2) security screws at the front of the housing
with the provide security tool. Set the access cover and screws
aside. Fig 1
Figure 1
2. Mount the wall bracket to the wall with appropriate hardware.
Fig. 2 shows the mounting pattern of the mounting surface.
PRODUCT INSTRUCTIONS
4. Installation of the PBRH10 Tilt bracket (See steps 1-8 in the
PBRH10 Installation instructions): Using the (2) 3/8" hex head
bolts and washers that are provided with the wall mount secure
the tilt bracket to the wall mount. Fig. 4 The wall mount has (4)
threaded inserts in which the (2) 3/8" hex head bolts attach. By
alternating the pattern of the (2) bolts you can achieve any pan
angle you wish. Fig. 4, 5
Figure 4
Figure 5
5. After achieving the desired pan angle tighten down the (2) 3/8"
hex head bolts. Continue the installation of the housing (steps
11-16 in the PBRH10 Installation instructions).
6. The wall mount packet assembly includes a 3/4" pipe plug, which
is to be treaded into the pipe coupling at the back of the tilt
bracket.
7. After the housing is installed the wall mount access cover can be
reinstalled. Fig. 6, 7
2.000
.500
1.500
2.000
5.500
Figure 2
1.000
.500
4X .390Ø
3. Run all incoming wiring through the hole in the back plate of the
wall mount bracket and up through the hole in the housing
mounting surface (in between the (4) threaded inserts). Fig. 3
Figure 3
Figure 6 Figure 7
1. Read Instructions - All the safety and operating instructions
should be read before the unit is operated.
2. Retain instructions - The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the unit and in the operating
instructions should be adhered to.
4. Follow Instructions - All operating and user instructions should
be followed.
5. Electrical Connections - Only a qualified electrician should
make electrical connections.
6. Attachments - Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Cable Runs - All cable runs must be within permissible distance.
8. Mounting - This unit must be properly and securely mounted to
a supporting structure capable of sustaining the weight of the
unit. Accordingly,
a. The installation should be made by a qualified service person
and should conform to all local codes
b. Care should be exercised to select suitable hardware to install
the unit, taking into account both the composition of the mounting
surface and the weight of the unit. Be sure to periodically
examine the unit and the supporting structure to make sure that
the integrity of the installation is intact. Failure to comply with the
foregoing could result in the unit separating from the support
structure and falling, with resultant damages or injury to anyone
or anything struck by the falling unit.
SAFETY PRECAUTIONSIMPORTANT SAFEGUARDS
CAUTION
RISK OF
ELECTRIC SHOCK!
CAUTION: TO REDUCE THE RISK OF
ELECTRICAL SHOCK, DO NOT EXPOSE
COMPONENTS TO WATER OR MOISTURE.
The lightning flash with an arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of non-insulated
" dangerous voltage" within the product's
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
!
UNPACKING
Unpack carefully. Electronic components can be
damaged if improperly handled or dropped. If an item
appears to have been damaged in shipment, replace it
properly in its carton and notify the shipper.
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Be sure to save:
1. The shipping carton and packaging material. They are the
safest material in which to make future shipments of the
equipment.
2. These Installation and Operating Instructions.
SERVICE
For service on Panasonic/Videolarm equipment contact:
Panasonic Technical Center
54 West Gude Dr.
Rockville MD 20850-1150
Phone: 301-762-5125
Fax: 301-251-0347
PANASONIC TECHNICAL SUPPORT
1-800-528-6747
9:00 AM - 5:00 PM EASTERN TIME
- 2 -