Panasonic NV-FJ613ECMS, NV-SJ216EGNK, NV-SJ216EGS, NV-FJ613ELS, NV-FJ613EGYK User Manual

...
Video Cassette Recorder Operating Instructions
NV-FJ614 Series (Hi-Fi) NV-FJ613 Series (Hi-Fi) NV-SJ216 Series (Mono)
Contents
Connecting and Setting up
Controls and Components Playback
TV Operation VCR Operation Menu Operation
Recording Timer Recording
Page
2
3
4
5
6
N2QAKB000001
Model:
NV-FJ614
N2QAKB000007
Model: NV-FJ613 NV-SJ216
Standard Accessories: 1 remote control 1 RF coaxial cable 1 mains lead 2 batteries, type R6
Other VCR Functions VCR Settings
Satellite- or Digital Receiver
Functions of the NV-FJ613 EC/ECM/ECN/ECY Series (Hi-Fi)
Functions of the NV-FJ614 Series (Hi-Fi)
Troubleshooting
Index Specifications
OSD = On Screen Display VCR = Video Cassette Recorder TV = Television
8
10
11
12
14
16
Please read through all these operating instructions (especially the safety information) before connecting or operating the VCR, or adjusting any settings.
VQT9002
Warning and Important Information
Please observe copyright laws when recording sound tracks and film.
Safety Information
This equipment complies with European conformity requirements, in accordance with the conditions of electromagnetic compatibility and product safety.
For your own safety and to protect the VCR:
Do not remove outer cover, to prevent electric shock. There are no serviceable parts inside. Refer all servicing to qualified service personnel. Only transport and set up the VCR in a horizontal position. Only connect cables when all the parts of the VCR are switched off. Only clean the outside of the VCR, using a soft cloth and no cleaning fluid. The mains lead must not be used for other equipment. In case of rapid temperature changes, do not operate your VCR for minimum 1 hour.
As this equipment gets hot during use, operate it in well ventilated place; do not install this equipment in confined space such as a bookcase or similar unit.
To prevent fire, electric shocks and damage :
The VCR, the remote control, the mains lead and the cassettes must not be used if it is damaged. Protect them from:
Insertion of fingers or objects Direct sunlight, heat, cold, rain, wetness, soiling and dust Shock and mechanical stress (do not bend the mains lead) Electric and magnetic fields Lightning strikes during thunderstorms (disconnect mains and aerial plugs)
This equipment complies with the requirements of protection class 2.
This equipment complies with the safety requirements of the VDE (German Association of Electrical Engineers).
Conserve the environment: See Power save on page 9.
Disposal of old equipment:
Batteries, packaging and old equipment should not be disposed of as domestic waste, but in accordance with the applicable regulations.
Instructions on inserting Remote Control Batteries:
The lifetime of the battery is about 1 year, depending on the frequency of use. Do not use one old and one new battery, or different types of batteries together (e.g. one alkali and one zinc-carbon battery). Only insert batteries which contain no toxic materials (such as lead, cadmium, mercury). Do not use rechargeable batteries (nickel-cadmium batteries). If the remote control will not be used for a long time, remove the batteries and store them in a cool and dry place. Do not heat or short-circuit the batteries. Remove spent batteries immediately and replace them with type AA, UM3 or R6. Observe the and polarities when replacing the batteries.
2
VQT9002
Connecting and Setting up
Set up the connections shown here, and connect the mains lead (supplied) to your AC mains.
Aerial
VCR
RF in
AV
RF out
(not supplied)
RF Coaxial Cable
(supplied)
21-pin Scart cable
(not supplied)
Note:
The RF (radio frequency) coaxial cable must be connected for TV reception, even if the video recorder is already connected with a 21-pin Scart cable.
Automatic Setting
Switch on the VCR and the [Country] setting menu will appear. Use the cursors on the remote control to select your country. (Operation of cursors see Menu Operation on page 5.)
On Screen Display
Panasonic VCR Country
Belgien Deutschland Belgique Österreich Belgiê Portugal
TV
If you want to connect the TV only with a RF Coaxial Cable (supplied),
you must ensure that the video output channel is adjusted to the input channel of the TV.
For this purpose, please also read the operating instructions for your TV.
Switch on the VCR Press the MENU Button for about 7
seconds until the number of the channel appears on the VCR display (the pre-setting is channel 36).
Tune the TV until the test screen appears.
A distorted picture on the channel can be reduced, by adjusting the VCR and the TV to another channel.
Use this button to select the channel number (e.g. channel 39).
Tune the TV until the test screen appears.
To store this adjustment, press .
VCR
RF Coaxial Cable
(supplied)
On Screen Display
VCR display
VCR
Ch:36
VCR
Ch:39
TV
After pressing , all the TV stations which can be received will be tuned automatically in about 5 minutes.
When the menu [Clock setting] appears, use the cursors on the remote control to select the Time and Date manually.
Panasonic VCR Clock setting
Clock setting : MAN. Time : 20:30:24
Date : 21.03.01
To end this procedure, press .
Press this button to exit the Settings.
Notes:
More information about the remote control, see page 4-5. If the selection for the Country menu does not appear
after switching on the VCR, you can restart the Automatic Setting; see VCR Settings on page 8. An incorrect setting of Time or Date (observe summer- and wintertime) will influence the Timer recording. If you select the country [Suisse] the menu [Power save] will appear. Select the settings with the cursors and store with . More information see on page 9.
After that, please continue with the Automatic Setting with the [Country] setting menu.
VQT9002
3
Controls and Components
The functions of these buttons can be operated by the remote control or directly on the VCR. In this description, the remote control symbols are used in most cases.
VCR display
AC IN
AV1 (TV)
RF IN
RF OUT
Playback
VCR display
Playback (indicated by = )
Fast Forward and Forward Search (Cue)
Fast Rewind and Backward Search (Review)
To select Fast Forward or Fast Rewind, press these buttons when the video has stopped. To briefly watch the picture during Fast Forward or Fast Rewind, hold down the corresponding button. To Search press these buttons briefly during playback, and the search will continue until the Playback Button is pressed. Two times pressing increases search speed (JET SEARCH). If you keep this button pressed, the search function will continue until you release the button.
Stop (indicated by = ) To stop winding a tape, recording or playback.
Still Playback
Press this button during playback
on the remote control or on the VCR .
Resume normal playback by pressing
this button again or the Playback Button .
4
For NV-FJ614 Series (Hi-Fi) see page 12.
Slow Playback
Keep this button pressed down on the remote control for more than 2 seconds during playback. Resume normal playback by pressing the Playback Button .
Notes:
To preserve the video heads, the following functions are switched off automatically after 5 - 10 minutes (Distorted pictures and tape transport noises during these functions are not functional faults):
Forward Search (Cue) Backward Search (Review) Jet Search Still Playback Slow Playback.
VQT9002
TV Operation
Menu Operation
This part of the remote control is used to operate some Panasonic TV.
To switch the TV on and off.
To select the AV input on the TV.
To operate the TV volume.
To select the TV channel.
VCR Operation
To remove the cassette,
press the EJECT Button on the VCR or press the Button for more than 3 seconds on the remote control.
These buttons are also used as cursors in order to select items on the menu.
To display the Main menu.
To EXIT a menu.
To select or store a function.
To switch the VCR on and off To change the Sound mode,
press this button repeatedly.
This button is only activated for : NV-FJ614 Series (Hi-Fi), NV-FJ613 Series (Hi-Fi)
Stereo sound: Display L R Left channel: Display L Right channel: Display R Mono sound: No display appears.
To display the time, Tape counter or Remaining tape time
press this button repeatedly.
To reset the Tape counter
press this button. When inserting a cassette, the counter is reset to 0:00.00 .
To change over to VCR AV channel
press this button repeatedly.
To operate REPLAY Function,
press this button while playback
VQT9002
5
Loading...
+ 11 hidden pages