Panasonic MC-RS765W487 Operating Instructions Manual
Safety Precautions
Emergency treatment
method
Attached with a warranty card
Operating Instructions
Robotic Vacuum Cleaner
Reserve it for later use
Before use
Usage
•
Maintenance
Troubleshooting
Operating Instructions
Robotic Vacuum Cleaner
Model No.
MC-RS765W487
Page
Contents
EN2
•
•
• Getting the room ready
• Set up the charging base
EN4
EN9
EN10
EN12
(Domestic use)
Part Names
Let＇s check the accessories
Safety Precautions
Emergency treatment
method
Notes on Use
Before use
Charging
Before use
Attached with a warranty card
Thank you for purchasing Panasonic product.
All illustrations used are for explanation purposes, actual item may vary
slightly from those shown.
Please read the operating instructions carefully before charging and
using the appliance to ensure safe and correct operation.
Before use, please make sure to read “Safety Precautions＂
(Pages EN4 ~ 8).
Keep the operating instructions for future use.
Reserve it for later use
EN13
• Automatic mode
• Thorough mode
• Borderline mode
• Spot mode
• Arch mode
EN15
• Using the remote controller
EN16
EN18
EN21
EN25
EN26
Cleaning
Other operations
Disposing of the dust
(Maintenance)
Maintenance
Troubleshooting
Product disposal
Specifi cations
Usage
Maintenance
Troubleshooting
Part Names
With the touch
of a
button
The
house dust detector lamp
fi nds the dust that you can＇t see!
The unit is shaped so that the side
brush reach all the way to the edge,
so dust is collected right up to the
every corners of the room!
Simple start with the
remote controller!
Part Names
With the touch
of a
button
Start cleaning from the
charging base or anywhere
else!
The
house dust detector lamp
fi nds the dust that you can＇t see!
When there is a lot of dust, the unit will travel
back and forth slowly to clean carefully.
The unit is shaped so that the side
brush reach all the way to the edge,
so dust is collected right up to the
every corners of the room!
Let＇s check the accessories
Parts enclosed in are included accessories.
Remote controller
Thorugh button (P. EN13)
Borderline button (P. EN14)
Infrared transmitter
Spot button
(P. EN14)
Arch button
(P. EN14)
Direction buttons
(P. EN15)
Start/Stop button
(P. EN13)
Home button
(P. EN15)
Batteries (AAA)
Insert the batteries
−
Simple start with the
remote controller!
(Bottom of the
remote controller)
AC Adapter • Charging base
AC Adapter
Insert
＋
−
Power lamp
Infrared transmitter
Recharging terminals
＋
2
Main unit
Sensors
Control panel
Before use
Side brush (R)
Rotating brush
Sensors
The infrared sensors and fall prevention sensors
detect obstacles so the unit can avoid the obstacles
while it is operating.
[There are cases when obstacles cannot be detected
(P. EN21 ~ 22) ]
Cover
Wheel
Roller
Infrared sensor
(Underneath the
main unit)
Recharging
terminals
Brush cover
Side brush (L)
Wheel
Battery cover
Rechargeable
battery is inside
Infrared receiver
Receives the infrared
signals from the
s
charging base and
remote controller.
Fall prevention sensors
Before use
Control panel
House dust detector
lamp (red)（P. EN13
Dust box
Main power
switch
Start/Stop button
Side brush
）
Status display lamp (blue)
3
Safety Precautions
If the battery leaks and liquid gets onto your skin or clothes, wash
carefully with clean water
Please store the vacuum cleaner (battery) in a clean, dry place
Do not mishandle
Use the designed AC adapter and charging base to recharge
Do not mishandle
If battery liquid gets into your eyes, immediately wash with clean water
(Do not rub your eyes)
Do not touch the batteries with wet hands
Safety Precautions
In order to prevent accidents or injuries to the user, other people, and damage to property, please follow the instructions below.
The following charts indicate the degree of damage caused by wrong operation.
Indicates a potentially hazardous
The symbols are classified and explained as follows.
situation which, if not avoided,
could result in death or serious
injury.
Please make sure to
follow these instructions
Indicates a potentially hazardous
situation which, if not avoided,
could result in death or serious
injury.
Indicates a potentially hazardous
situation which, if not avoided,
could result in minor or moderate
injury.
This symbol indicates prohibition.
Do not mishandle
(This can cause leakage, overheating, ignition, rupturing or electric shock)
The main unit has a built-in rechargeable battery, which cannot
be used in other electrical appliances
Do not dispose of the battery in a fire or expose it to heat
Do not pierce with nails, apply impacts, disassemble or modify
Do not short-circuit by allowing metals or other materials to come into contact with
the socket terminals
Do not transport or store with metal objects such as necklaces or hairpins
Do not charge, use or place in places with high temperatures, including near fire or in hot weather
Do not expose to water or other liquids
Rechargeable battery
Use the designed AC adapter and charging base to recharge
(Not doing so can cause electric shock, ignition, overheating or injury)
This symbol indicates requirement that must
be followed.
To avoid injuries resulting from overheating,
ignition, electric shock or rupturing...
To avoid fi re, burns, electric shock and etc.
Do not touch the batteries with wet hands
(This can cause overheating, ignition or electric shock)
If battery liquid gets into your eyes, immediately wash with clean water
(Do not rub your eyes)
(Danger of blindness)
Seek for professional medical treatment immediately.
Do not mishandle
Do not leave where it is exposed to direct sunlight or in hot places
(This can cause overheating, rupturing or ignition)
Do not place items on its top, or place it where you can drop it easily
(This can cause overheating, ignition, electric shock or injury)
If the battery leaks and liquid gets onto your skin or clothes, wash
carefully with clean water
(This can cause skin infl ammation and injury)
Please store the vacuum cleaner (battery) in a clean, dry place
(so as to avoid the battery from moisture which leads to overheating, ignition or electric shock)
4
To avoid ignition, injury and etc.
Do not use in the following places
Do not try to ride on the main unit, place heavy
objects on it, or apply strong impacts to it
Do not try to lift the main unit by the cover when the cover is open
Do not smoke or carry combustible matter
Do not touch the rotating brush, wheels or side brushes
Do not mishandle
Do not put adhesive tape or stickers on the fall prevention sensors
Before use
Do not smoke or carry combustible matter
(So as to avoid an explosion or fi re)
Do not touch the rotating brush, wheels or side brushes
(Danger of injury and burns)
Be particularly careful when there are children around.
Do not put adhesive tape or stickers on the fall prevention sensors
Main unit
•
AC Adapter
•
Charging base
(This can cause injury, fi re or electric shock due to falling of the
main unit)
Do not mishandle
Do not wash with water (except for those parts and accessories
that can be washed with water)
Do not use around wet places, such as in toilets and bathrooms
Do not disassemble, repair or modify (except for the removal
and attachment of the side brushes as described in
“
Maintenance＂ (P. EN20)) (This can cause fire and electric shock)
Do not plug or unplug the mains lead with wet hands (Danger of electric shock)
Do not damage the power cord or the power plug. Do not forcefully machine, bend, twist, stretch
or place the cleaner at high temperatures or place heavy objects on its top or bundle it (This can
cause an electric shock, short circuit or fire)
→
Consult the place of purchase for information about repairs.
Do not use if the charging base, AC a
(This can cause fire due to overheating and ignition)
Do not place recharging terminals of the main unit or charging base with metal objects
(This can cause leakage, overheating or ignition due to shorting)
Do not insert items such as needles or bits of metal into the inside of the main unit or charging base
(This can cause overheating, ignition or electric shock)
Do not falls, shocks, and water (This can cause electric shock, ignition or abnormal overheating)
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety
To avoid fi re, burns, electric shock and etc.
Cigarettes, toner from a copier,
heating fuels, thinners, etc.
dapter, plug or mains lead are damaged
Before use
Do not use in the following places
(This can cause injury, fi re or electric shock due to falling
of the main unit or charging base)
Spring layer or corridor without fence
•
In entrance halls, stairways or steep slopes
•
In narrow areas where the main unit cannot turn around
•
On top of refrigerators or similar locations that are high
•
set but lacking in space
Do not try to ride on the main unit, place heavy
objects on it, or apply strong impacts to it
(Danger of injury)
Do not try to lift the main unit by the cover when the cover is open
(This can cause injury due to falling of the main unit)
5
Children should be supervised to ensure that they do not play with the
appliance
Use the mains lead or plug properly
Use the AC adapter or charging base properly
Observe the following
Objects that can cause accidents if the unit comes into
contact with them should be moved out of the way
When an error occurs, stop using it immediately, turn off the main
power switch, and unplug the power plug of the AC adapter
Emergency treatment method
Safety Precautions
(continued)
Safety Precautions
To avoid fi re, burns, electric shock and etc.
Children should be supervised to ensure that they do not play with the
appliance
(It may cause fi re, electric shock or injury)
Use the mains lead or plug properly
Insert fully into the socket
(There is a danger of electric shock or fire due to overheating if you do not plug into the
socket outlet)
Must be within the rated values of the socket and the wiring appliances, etc., and must use
AC 110 V (Overheating lead to fire can result if the system exceeds recommended ratings
Main unit
•
AC Adapter
•
Charging base
by plugging too many devices into the same socket.)
Please unplug the power plug when the unit is not to be used for a long period of time
(To avoid electric shock, electric leakage, fire, etc. caused by insulation damage)
The plug must be removed from the socket outlet before maintaining
the appliance (Danger of electric shock)
Remove dust regularly with a dry cloth
(Dust gathered can lead to incomplete insulation caused
by moisture, which can lead to fire)
Use the AC adapter or charging base properly
The AC adapter and the charging base are limited to charging the vacuum cleaner
(Not doing so can cause electric shock， ignition
The AC adapter and the charging base are only suitable for indooruseor to guard against rain
(Not doing so can cause electric shock, ignition)
Observe the following
Keep pets out of the way in their enclosures or in other areas
(This can cause accidents, electric shock or injury)
Perform maintenance when the fall prevention sensors are dirty
(This can cause injury due to falling)
Turn off the main power switch when performing maintenance or when only
children or pets are present (It may cause electric shock or injury)
(continued)
, overheating or injury)
Please make sure to
follow these instructions
Objects that can cause accidents if the unit comes into
contact with them should be moved out of the way
(To avoid accidents, fi res, injuries)
Burning candles, cigarettes, vases, etc.
•
(There is a danger of falling if the unit hits these objects)
Electronic devices, such as fans, with control panels at about the
•
same height as the main unit (The main unit may hit the control panels
of the other household electronic devices
Emergency treatment method
When an error occurs, stop using it immediately, turn off the main
power switch, and unplug the power plug of the AC adapter
(Danger of smoke, ignition, and electric shock)
e.g. abnormality or breaking down
The unit doesn＇t work when the
•
Start/Stop button is pressed, even though
the battery has been charged
When the power plug or the power cord is
•
pulled, the power lamp is on and off
→
Immediately request maintenance and repair at the place of purchase
There are strange noises when the unit is
•
operating
The main unit deforms or becomes very hot
•
There is a burning smell
•
6
Do not approach the fi re source or the heat source, and avoid
direct sunlight
Do not use on carpet or fl ooring that can be easily damaged
(waxed fl oors, marble fl oors, etc.)
Observe the following
Do not spy on the vacuum cleaner during operation
Do not put objects on tables during operation
Do not mishandle
Environmental protection
When carrying the main unit, stop operation and
carry carefully with both hands
Do not use it on damaged tiles, carpets or old tatami mats
Before use
Main unit
•
AC Adapter
To avoid ignition, injury and etc.
Do not approach the fi re source or the heat source, and avoid
direct sunlight
(This can cause fi re or deformation)
Do not spy on the vacuum cleaner during operation
(This can cause falls and injury)
Do not put objects on tables during operation
(These objects may be caused to fall if the main unit hits the table)
Do not mishandle
Stop use if sand or gravel becomes attached to the brush covers, wheels, roller or side
brushes or if these parts start to wear down (This can cause scratching to the floor surface)
→
Check the unit before use, and if there is wearing, consult the place of purchase
Do not pull the main unit along
(This can cause scratching to the floor surface)
Do not pull the mains lead when unplugging from the socket outlet
(It may cause an electric shock or fire caused by short circuit)
Before use
Do not use on carpet or fl ooring that can be easily damaged
(waxed fl oors, marble fl oors, etc.)
(This can cause breakage and scratching)
→
Cease use if the unit causes damage
•
Charging base
Do not use it on damaged tiles, carpets or old tatami mats
(This may cause more damage or expansion of existing damage)
Environmental protection
When disposing of waste products (including rechargeable batteries, batteries), do not
stack them with general household waste (to avoid polluting the environment)
→
Please hand them over to the resource recycling unit for disposal
Observe the following
Please clean up fragile items in advance, or the items which will cause
trouble when inhaled and long rope, wire, cable, carpet with fringes, mats
or cushions. Please avoid the place which cannot be cleaned up
(This can cause breakage and scratching)
Please always carry out maintenance (P. EN16 ~ 20)
(This can cause
When carrying the main unit, stop operation and
carry carefully with both hands
(To avoid injury, fault, fl oor damage caused by falling)
Do not touch the control panel
Take care not to insert your fingers into the wheels and
the rotating brush
overheating and breakage)
7
Keep batteries out of the reach of infants and children
Do not mishandle
Observe the following
Safety Precautions
(continued)
Safety Precautions
To avoid fi re, burns, electric shock and etc.
Batteries (for remote controller)
Keep batteries out of the reach of infants and children
(This can cause accidents and injury)
If a battery is swallowed, consult your doctor immediately.
To avoid ignition, injury and etc.
Do not mishandle
Do not place in fire or excessive heat
Do not replace the batteries while your hands are wet
Do not mix new and old batteries or different types of batteries
(This can cause leakage, overheating, rupturing or ignition)
Observe the following
Follow the warnings printed on
batteries
Use batteries within their
recommended lifetime
Confirm the
batteries and insert correctly
－ end of the
+
(continued)
Remove the batteries when the unit is not to be used
for a long period of time
Remove flat batteries immediately
Use adhesive tape to insulate the terminals of the
batteries when disposing of them (This can cause
overheating, rupturing, injury or pollution through
leakage)
Please make sure to
follow these instructions
8
Notes on Use
Before use
Notes on Use
The vacuum cleaner is a household vacuum cleaner and should not be used for commercial or industrial purposes and for
other purposes other than dust absorption.
Do not allow the unit to suck the following objects (This can cause malfunctions and odours)
• Dehumidifi cation powders • Large volumes of powder (Construction waste or fi re extinguisher powder)
• Pet litter or anything with pet waste attached
• Glass, pins, needles, toothpicks • Long pieces of string • Water and other liquids
• Damp or wet items • Carpet fringes
• Impermeable items such as clear food wrap and other wrapping fi lms
• Adhesive items (insect catcher sheets and etc.)
Do not try to clean in places with large volumes of sand, pet litter or gravel (This can cause malfunction)
→
The vacuum cleaner is suitable for flat indoor environment such as wood flooring, tiles or undercoat hard carpet
[thickness (including hair length) below 7 mm]
Do not push the wheels out of shape (This can cause incorrect operation)
Do not lubricate the rotating brush (This can cause breakage)
Do not block the suction port or exhaust port (This can cause deformation due to overheating)
Do not use the product on the concrete floors that have hard or uneven surfaces (This may cause wear and tear to the
brush covers, side brushes, wheel and roller)
Do not use while a security system is operating (This may cause the security system to operate incorrectly)
Do not block the sensors, infrared transmitters and receivers on the main unit or charging base by putting tape or stickers
on them or blocking with cloth (This may cause operational failure and malfunction)
Do not use the vacuum cleaner in extremely hot or cold environments (as the rechargeable battery in it cannot work
properly)
→
It is recommended to use the vacuum cleaner in the environment of 0 ℃ ~ 40 ℃(please charge it in 5 ℃ ~ 35 ℃)
To avoid the power cord from being drawn into the vacuum cleaner and hindering it, please put the charging base along
the edge of the wall, and finish the power cords and ropes of other electrical appliances in advance
(This may cause malfunction and operational failure for example the mains lead get wound up)
Before use
9
Before use
Do one of the following to ensure smooth operation.
Items that can block the main unit
Items that may operate
incorrectly if hit by the
main unit
Places you don＇t want the
unit to go
Items that may fall if hit by the
main unit
Items that may accidentally be sucked
Items that may damage the fl oor
Items that can get caught up in the
rotating brush, side brushes,
wheels or roller
Before use
Getting the room ready
Do one of the following to ensure smooth operation.
Tidy up before starting
Please move items to other rooms
Place a weight that can be used as a guard bar before
the items to be protected
Items that can get caught up in the
rotating brush, side brushes,
wheels or roller
Carpets, rugs, and mats made
•
from soft materials that have
long threads (about 7 mm or more)
Thin floor coverings such as bath mats
•
Non-slip rubber mats and other
•
thin coverings with adhesive
properties
Fringes of coverings and floor
•
cushions
The ends of table cloths and curtains
•
that reach to the floor
Wire, cable, etc
•
Long thin items such as
•
strings and belts
Thin paper, material,
•
and plastic bags
Broom, etc.
•
Items that may accidentally be sucked
Items that may damage the fl oor
Burning items such as cigarettes,
•
incense, and candles
Small items that can be sucked up easily
•
Hard items such as coins, small
•
stones, metals, plastics
Pet excrement and liquid
•
Fragile items on the floor such as glass and
•
pottery
Adhesive items (insect catcher sheets and etc.)
•
Precious metals such as accessories
•
༬൧
Items that may fall if hit by the
main unit
Tall thin furniture such as hat and
•
coat stands
Items that can block the main unit
Furniture with legs (tables and etc.)
•
Cushions, books, magazines, etc.
•
Control panels of electric carpets and etc.
•
Threshold, steps and etc.
•
Footwear
•
Items that may operate
incorrectly if hit by the
main unit
Electronic devices with control
•
panels at the same height as the
main unit
Places you don＇t want the
unit to go
Easily damaged furniture or walls
•
(sliding screens, folding screens and
etc.)
The segment difference or uneven
•
place where the main unit is easy
to be blocked and cannot move
Windows and mirrors that reach the
•
༬Ӄ
floor and etc.
Stairs, entrance halls and etc.
•
Heaters and other heat producing devices
•
If the product stops operating you are
•
unable to reach it (for example under the
furniture)
If the room receives direct sunlight, use a thick curtain (to avoid malfunction)
You cannot use the unit to clean the following places
(the unit may get tangled up or stop running properly)
On carpets with threads 7 mm or longer
•
Mirrored surfaces (glass, mirrors, marble and etc.)
•
(This can cause damage to the floor covering or floor surface or cause the main unit to malfunction or break)
Areas less than approximately 35 cm
•
If the barrier has a difference of approximately 1.5 cm or more (depending on conditions, the unit may be unable to
•
overcome the barrier even though it is less than 1.5 cm)
(This can cause the main unit to stop while moving or to try to mount level differences)
10
The location should be
Put the charging base
up against the wall
Set up the charging base
Before use
Set up the charging base
The location should be
A room where the main unit is often used
A place with even flooring without rises or bumps
A place with plenty of room and few obstacles
Insert the power supply, the
power lamp light (red)
Put the charging base
up against the wall
(This is to make sure the
charging base doesn＇t move by
being pushed by the main unit)
Approx.120 cm
Before use
Approx.120
Keep obstacles
out of this area
cm
Approx.150 cm
Do not place objects
within this area
(To make sure that the main unit
Draw the mains lead along the wall without
bundling it together
Note
The main unit may not correctly receive signals from the charging base and remote controller. (P. EN24)
• When sunlight gets in the room (including sunlight entering through frosted glass)
• When using devices that emit infrared signals
• When the main unit is within 1.5 m in front of the charging base and you use the remote controller
can return to the charging base
automatically)
11
Charging
To help make the battery last longer
1
Turn on the main power switch.
2
Put the main unit in the charging base
Click
Charging
The battery is not fully charged at the time of purchase, so please be sure to
charge before use
(full charge takes about 2.5 to 5 hours)
To help make the battery last longer
If the unit is not used for one month or more, charge the unit fully, turn the main power switch off for
storage, then recharge the unit at least once half a year thereafter. (Storing the unit in an uncharged
state will adversely affect the performance and lifespan of the battery.)
Recharge in a room where the temperature is between 5 ℃ and 35 ℃. The unit cannot charge
properly if the room is too cold or too hot (such as when the room receives direct sunlight). The
operating time will be shortened and recharging times will increase.
Turn on the main power switch.
1
②
Open
①
Press
ON
OFF
Click
Under normal circumstances, leave the main power switch on
Request
2
When the status display lamp on the main unit doesn＇t
•
light or goes out immediately, try putting the main unit in
the charging base again (If the main unit is correct placed,
the status display lamp will gradually turn from dim to
bright, and then turn from bright to dim repeatedly)
When the unit is not to be used for 6 months or more, the
•
battery may over-discharge and operating time may be
reduced, so make sure you recharge it before using it again
In order to avoid interference with TV sets, telephones,
•
etc. (such as noise), please charge more than 1 m away
from these appliances.
Put the main unit in the charging base
(The status display lamp will gradually turn from dim to
bright, and then from bright to dim repeatedly)
How to read the lamps
Charging
Charging complete
•
(The unit cannot charge if the main power is switched off.)
Gradually from dim to bright,
and then from bright to dim repeatedly
Status display lamp
Always on (blue
The temperature of the battery can change depending on
•
the ambient temperature, usage time, and other usage
conditions. When the temperature of the battery is too high
or too low, the unit waits until the battery reaches a level
suitable for charging, so charging times may increase.
The main unit and charging base may become warm while
•
charging, but this is normal.
The length of time the unit can run varies depending on the
•
temperature of the battery and other usage conditions.
When AC adapter or charging base is inserted into a power
•
socket, there will be about 1 W of power consumption even
if they do not charge.
Status display lamp
When charging is abnormal,
refer to“Troubleshooting＂
(P. EN23)
)
NoteRequest
12
Remote controllerRemote controller
The house dust detector lamp tells
you when it fi nds dirt.
Cleaning
Open the main power switch, and
enter the dormant state ...
Automatic mode
Thorough mode
Main unitMain unit
Remote controller
Using
Usage
•
Maintenance
Cleaning
Open the main power switch, and
enter the dormant state ...
Press and hold the main unit or remote
controller
then the status display lamp fl ashes
several times and remains on (the main
unit issues a “beep＂ at the same time)
The unit enters standby state to
save the battery when you do not operate
it for about 2 minutes. (Sleep)
to enter the standby mode,
Automatic mode
Always on Normal
Status display lamp
Flashing Limited power
Abnormal
→
Please turn off the main power
switch, confirm the condition of
Fast
fl ashing
the various parts of the product;
remove the abnormality, and then
re-open the main power switch
and use the vacuum cleaner (P.
EN21, 23)
Thorough mode
Using
Start cleaning
The main unit automatically identifi es
it is the wall or the central room, and
automatically changes its direction, and
clean the whole room.
Remote controller
Press
Request
Note
Close the door if you do not want the unit to go into other rooms.
•
It cannot sense an obstacle when retreating, so a collision may occur.
•
The unit can start cleaning anywhere, not just from the charging base.
•
The unit avoids the charging base when it is cleaning.
•
The main unit stops operation if you lift it during cleaning.
•
Press
It cleans the whole room more
thoroughly at a speed half that of
automatic mode.
Press
Usage
Maintenance
Note
Finish cleaning
When the cleaning is finished, please return the
(manually get it back to the charging base or press the Home button).
If the battery is low during cleaning, the
will flash, and the cleaner will automatically return to the charging base.
•
Press the of the main unit or the of the remote controller
The house dust detector lamp tells
you when it fi nds dirt.
The house dust detector lamp senses the dust
diffi cult to see. (dander, mites can also be sensed)
When there is a lot of dust, the main unit will
move back and forth repeatedly.
This does not light when the unit is returning to
the charging base.
main unit to the charging base
main unit will issue a sound of beep, the status display lamp
Clean
Lamp
off
Flashing
(Red)
Lighting
(Red)
A lot of dust
13
Remote controllerRemote controller
Remote controllerRemote controller
Remote controllerRemote controller
Borderline mode
Spot mode
Arch mode
Cleaning
(continued)
Cleaning
Borderline mode
(continued)
Spot mode
Arch mode
The main unit automatically goes
straight to the wall, and then clean
along the wall. When detecting a
corner, it repeats the corner
cleaning. When the cleaning is
completed, it automatically returns
to the charging base for charge.
Cleaning Pattern
：
Start position
Note
Start cleaning
Depending on the cleaning environment, the actual cleaning path may be deviated.
•
With the start position as the center,
the vacuum cleaner fi rst cleans
outwards in a swirling manner; and
when the diameter has reached
approximately 1 m, the cleaner
cleans inwards in a swirling manner,
and then returns to the center and
automatically stops.
The vacuum cleaner stays in the
range of 1 m × 1 m from the start
position , and cleans in an arc
cross manner. It automatically
stops after it fi nishes cleaning.
Cleaning Pattern Cleaning Pattern
：
Approx.1 m
Start position
：
Start position
Finish cleaning
When the cleaning is finished, please return the
(manually get it back to the charging base or press the Home button).
If the battery is low during cleaning, the
will flash, and the cleaner will automatically return to the charging base.
Press
Close the door if you do not want the unit to go into other rooms.
Request
Note
Press the of the main unit or the of the Remote controller
•
It cannot sense an obstacle when retreating, so a collision may occur.
•
The unit can start cleaning anywhere, not just from the charging base.
•
The unit avoids the charging base when it is cleaning.
•
The main unit stops operation if you lift it during cleaning.
•
The house dust detector lamp does not light in these three cleaning modes.
•
main unit will issue a sound of beep, the status display lamp
Press
main unit to the charging base
Press
14
Other operations
When using the remote controller
To switch between different cleaning modes, you need to press
to stop
the original mode, then press the corresponding mode button
Operate (the unit moves only while you are
pressing the button)
Using the remote controller
Usage
•
Maintenance
Other operations
Using the remote controller
When using the remote controller
The remote controller can be used within a range of about 5 m
•
Point the infrared transmitter of the remote controller at the infrared receiver
•
of the main unit
Make sure there are no obstacles to the signal between the remote
•
controller and the main unit
Don＇t cover the infrared transmitter of the remote controller with your finger
•
To switch between different cleaning modes, you need to press
•
the original mode, then press the corresponding mode button
Operate (the unit moves only while you are
pressing the button)
Use the direction buttons on the remote controller to move the unit to the
place you want to clean. (The unit cleans as you are moving it)
…Forward …Turn left …Turn right
Note
You can move the main unit using the remote controller
•
even when it is cleaning.
(In automatic, thorough or borderline modes)
When returning the main unit to charge, you can make it
•
back to the charging base more quickly by combining with
the remote controller arrow buttons.
to stop
Return to charging base
●
You can also use the Home button to
return the unit to the charging base.
Note
Depending on the usage conditions, the unit may not
•
be able to return to the charging base even when you
have pressed Home button. (P. EN24)
The house dust detector lamp does not light when the unit
•
is returning to the charging base.
(but the rotating brush and the side brush will still turn)
Usage
Maintenance
15
Please turn off the main
power switch before
cleaning the rubbish
Disposing of the dust (Maintenance)
Please dry the dust bin completely for about 24 hours
immediately after washing
Empty the dust box (Maintenance)
Disposing of the dust (Maintenance)
Empty the dust box (Maintenance)
Please turn off the main
power switch before
cleaning the rubbish
Empty the dust box and perform
maintenance as necessary.
Dust gathers in different ways depending
on the type of dust.
Note
Even if a site is low in dust, the dust absorption effect
•
will be affected if the air intake is blocked.
(Remove the dust box and remove the dust from the
air intake)
The dust box may become full earlier on new carpets
•
because of the presence of loose threads.
Request
It is advisable to remove dust after each cleaning.
When washed with water...
Please do not use substances such as detergent,
•
bleach, gasoline, thinner, or alcohol (to avoid cracks
and colour change)
Please dry the dust bin completely for about 24 hours
•
immediately after washing (to avoid odor or clog)
Please do not use blow dryer or similar device to dry it
•
(to avoid deformation and malfunction)
Soft hair toothbrush and etc.
Mesh Filter
Pleats fi lter
You can also use an old soft hair toothbrush to gently
brush out the garbage on the mesh fi lter (do not
press hard to avoid damage to the fi lter)
16
4
3
Carefully remove rubbish, dust etc.
And removing the pleats fi lter; clean the pleats fi lter and the mesh fi lter
5
Remove dust from the
air intake
)
1
Open the cover
2
Remove the dust
box and empty it
You can wash with water if
the dust box is especially dirty
6
Reassemble the dust box and
put back into the main unit
(After the dust box is installed,
please close the cover)
Usage
•
Maintenance
1
2
3
Open the cover
Remove the dust
box and empty it
In this process, the suction
inlet is facing upwards to
prevent dust from falling out
And removing the pleats fi lter; clean the pleats fi lter and the mesh fi lter
Press
＂
“
Tap lightly to shake off the dust
While opening
Face the suction
inlet upwards
Dispose of the dust
Carefully remove rubbish, dust etc.
4
You can wash with water if
the dust box is especially dirty
Pleats filter
Pour them directly under the faucet
(do not brush with a brush, etc.)
Remove dust from the
air intake
If you cannot remove it, detach the
5
6
rotating brush and perform maintenance.
(
P. EN18
Reassemble the dust box and
put back into the main unit
(After the dust box is installed,
please close the cover)
If the dust box is not installed or is not
installed in place, the cover will not be closed.
)
(dry properly before putting back in place)
Close the dust box
Dust box (including the mesh filter)
Rinse with water
Put back the dust box
Usage
Maintenance
17
Loading...