How it Works
Panasonic
Loading...
M16eGi
Specification
13 pgs159.8 Kb0

Panasonic M16eGi Specification

Model Name
Model No.
Switch-M16eGi
Product Specification
PN28160i-SG
401-28160i-SG-SP02
Page 1 of 13
1. Summary
Switch-M16eGi is an all Giga bit Ethernet Switching Hub with management function having 14 ports of 10/100/1000BASE-T and two pairs of 10/100/1000BASE-T port and SFP extension slot, one of which is selectable.
2. Feature
（1） Has wire speed layer 2 switching functions.
（2） Ports 1 to 14 are auto negotiation-ready 10/100/1000BASE-T ports. Their speed and communication mode can be changed
by configuration. Ports 15 and 16 can be used as a 10/100/1000BASE-T port corresponding to autonegotiation or an SFP extension slot exclusively. Also their speed and communication mode can be switched by configuration.
（3） All twisted pair ports support straight/cross cable auto sensing function. Simply connect devices with straight cables,
whether it is a terminal or a network device.(This function does not work if the port communication configuration is set at Fixed or Link Aggregation. Ports 1 to 14 are set at MDI-X. (default))
（4） Due to the loop detection/shutoff function, a port where loop has occurred can be automatically shut off to prevent loop
failures. When a port is shut off and recovered automatically, SNMP trap can be sent to notify the incident to the administrator. Moreover, the port with a loop can be identified by loop notification on the LEDs on the main unit and referring the history of loop on the setting screen.
（5） Has a loop detection history function, which notifies when a loop occurs with the corresponding LED and enables a network
administrator to identify the looped port after the loop is removed.
（6） Fanless design solves noise problem or fan failure.
（7） Power consumption can be suppressed by switching off the port LEDs (left) via the ECO mode LED functions.
（8）VLAN function allows free grouping of up to 256 VLANs.
（9） The IEEE802.1p compatible QoS function is supported.
（10） Has an Internet Mansion function, which ensures security between each door.
（11） Has a port grouping function, which groups ports that are allowed to communicate with one another to limit communications
between different groups.
（12） Equipped with energy efficient Ethernet （EEE） conforming to IEEE802.3az（LPI）. When there is no data transmission at link
up, the energy-saving state automatically starts so that power consumption can be reduced on each port. Factory default : Disable
（13） Embedded power saving mode detects the connection status automatically and saves power consumption to minimum.
Factory default : Disable
（14） IEEE802.1Q VLAN tagging is supported, and a maximum of 256 VLANs can be registered.
（15） The IEEE802.1X compatible user authentication function （EAP-MD5/TLS/PEAP） is supported.
（16） Each single port supports IEEE 802.1X, Web, and MAC authentication protocols, eliminating the need for individually
setting the ports’ authentication parameters.
（17） Supports ZEQUO assist Plus. Processes from introduction to maintenance can be performed easily.
Date issued Oct. 01, 2019
Date revised
Oct. 01, 2020
Model Name
Model No.
Switch-M16eGi
PN28160i-SG
3. Rated/Environmental Conditions
3-1. Power supply
3-2. Power consumption 3-3. Operating environment Temperature: 0 - 60℃
3-4. Storage environment Temperature: -20 - 70℃
3-5. EMC compliance CISPR 22 Class A
3-6. Safety compliance IEC 60950-1
3-7. Environment compliance
401-28160i-SG-SP02
Product Specification
Page 2 of 13
AC100-240V, 50/60Hz, 0.5A （with a built-in power supply）
Normally, Max : 11.6W, Min : 4.8W
Humidity: 20 - 80%RH （no condensation）
Humidity: 10 - 90%RH （no condensation）
EN 55022 Class A AS/NZS CISPR22 Class A VCCI Class A EN 61000-3-2, EN 61000-3-3 CISPR 24 EN 55024 IEC 61000-4-2, IEC 61000-4-3, IEC 61000-4-4, IEC 61000-4-5, IEC 61000-4-6, IEC 61000-4-8, IEC 61000-4-11
EN 60950-1 RoHS compliant
4. Form
4－1. Form and materials/colors
4－2. Mass（Weight） 2,200g
Dimensions ：44mm（Height）×330mm（Width）×230mm（Depth）
（Excluding protruding sections） Case material ：SECC Color : Main unit: Green 03, Front face: Black 03,
Face plate label: Black 04
Date issued Oct. 01, 2019
Date revised
Oct. 01, 2020
Model Name
Model No.
Switch-M16eGi
PN28160i-SG
5. Hardware Specifications
401-28160i-SG-SP02
Product Specification
Page 3 of 13
5－1. Interface
Twisted pair port 1-16 ：RJ45 connector （*1）
Transmitting and receiving network system：
IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX IEEE802.3ab 1000BASE-T
Energy Efficient Ethernet （*2） :IEEE802.3az （LPI）
Transmission speed ：10/100Mbps, full/half duplex
：1000Mbps, full duplex
Compatible cable ：Twisted pair cable
（At least equivalent to EIA/TIA568 category 5e） Maximum transmission distance ：100m Auto-Negotiation ：Communication speed and full/half duplex
are automatically recognized. The setting can be fixed to 10Mbps, 100Mbps, and full duplex or half duplex.
*1 Embedded power saving mode detects the connection status automatically
and saves power consumption to minimum. Factory default : Disable
*2 Energy Efficient Ethernet (EEE) conforming to IEEE802.3az (LPI).
When there is no data transmission at link up, the energy-saving state automatically starts so that power consumption can be reduced on each port. Factory default : Disable
SFP extension slots 15,16 Transmitting and receiving network system：
:IEEE802.3z 1000BASE-SX/LX
SFF-8472（DMI：Diagnostic Monitoring Interface）
*Select either of RJ45 or SFP for use
Optional Accessories :1000BASE-SX SFP Module（i） （PN54022-SG）
1000BASE-LX SFP Module（i） （PN54024-SG）
5－2. Switching mode
5－3. Terminal emulator
connection
Switching method ：Store and Forward Switching capacity ：32Gbps Packet transfer capability ：Non-blocking
Max 1,488,000pps/port（1000Mbps） Max 148,800pps/port（100Mbps）
Max 14,880pps/port（10Mbps） MAC Address table ：Max 8K entry/unit Buffer memory ：512K Bytes/unit Flow control ：half-duplex Back pressure
full-duplex IEEE802.3x Aging timeout ：10 to 100,000 sec. （Default: 300 sec.） Jumbo frame supported ：9KB Transmittable frames ：EAP,BPDU HOL Blocking Prevention ：Support
Console port ：RJ45 connector 1 port
Transmission mode ：RS-232C（ITU-TS V.24） Emulation mode ：VT100 Communication configuration ：9,600bps, 8bit, None Parity control,
Stop bit 1 bit
Date issued Oct. 01, 2019
Date revised
Oct. 01, 2020
Model Name
Model No.
Switch-M16eGi
PN28160i-SG
5. Hardware Specifications
401-28160i-SG-SP02
Product Specification
Page 4 of 13
5－4. LED display
（1）POWER（Power）LED
Green Light ：Power is ON Off ：Power is OFF
（2）ANY COL.（Collision） LED
Orange Light : During half-duplex operation, packet collision is
occurring in either port.
（3）STATUS/ECO （Status/ECO made）LED
Green Light : Operating in status mode. Green Blink : Operating in ECO mode.
All port LEDs（left） are turned off. Orange Light : Starting Orange Blink ： Malfunction（Contact the seller） Off : Power is OFF.
（4）GIGA（GIGA mode）LED
Green Light : Operating in GIGA mode.
（5）100M（Speed mode）LED
Green Light : Operating in Speed mode.
（6）FULL （DUPLEX mode）LED
Green Light : Operating in DUPLEX mode.
（7）LOOP HISTORY（Loop History mode）LED
Green Light : Operating in Loop History mode. Green Blink : Loop is occurring,
or occurred within the last 3days.
You can display the following items using the LED display change button. Display for the connection with a connected terminal （Status mode）,Display for the 1000 Mbps transmission rate （GIGA mode） , Display for the 100Mbps or 10 Mbps transmission rate （Speed mode）, Display for the full-duplex or half-duplex transmission system （DUPLEX mode）, Display for ports with a loop history （Loop history mode） , All port LED lamps can be turned OFF （ECO mode）.
Display of each port is refer to table 1 of No.5.
The mode at the start is called “Base mode”. There are two types of Base modes : Status mode （factory default setting） and ECO mode. You can change the Base mode by holding down the LED display change button （for at least 3 sec）. When the Base mode is changed normally, all STATUS/ECO , GIGA , 100M , and FULL LED lamps light up at the same time. When you release the button, the Base mode is changed to the selected mode. If the mode is changed to the GIGA mode, Speed mode, DUPLEX mode, or Loop History mode and the LED display switch button is not used for one minute or longer, the mode automatically returns to a Base mode （Status mode or ECO mode）. The Base mode is maintained even after the power is turned OFF.
LED display change button
Date issued Oct. 01, 2019
Date revised
Oct. 01, 2020
Loading...
+ 9 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use