Panasonic KX-TGF573, KX-TGF572, KX-TGF575, KX-TGF785SK, KX-TGF574 User Manual
Base unit
1
Connect the AC adaptor to the unit by pressing the plug firmly.
2
Fasten the cord by hooking it.
3
Connect the AC adaptor to the power outlet.
4 Connect the telephone line cord to the unit, then to the single-line telephone jack (RJ11C) until you hear a click.
5
A DSL/ADSL filter (not supplied) is required if you have a DSL/ADSL service.
Note:
L
Use only the supplied Panasonic AC adaptor PNLV226.
Charger
1
Quick Guide
Connections
4
Model No. KX-TGF572/KX-TGF573
KX-TGF574/KX-TGF575
KX-TG785SK
1
3
2
4
5
1 Connect the AC adaptor to the power outlet.
Printed in Malaysia
PNQW5232ZA PT1116AM0
Battery installation/Battery charging
2
1
4
2
3
1
1
2
Charge for about 7 hours.
Note:
L USE ONLY rechargeable Ni-MH batteries AAA (R03) size
L Do NOT use alkaline/manganese/Ni-Cd batteries.
L Confirm correct polarities (S, T).
L Follow the directions on the display to set up the unit.
L Confirm “Charging” is displayed
Removing the battery
()
.
().
1
2
– 2 –
Operating tips
Soft keys
By pressing a soft key, you can select the feature shown directly above it on the display. Pay
attention to the display to see what functions the soft keys are assigned during operation.
Navigator key
Handset:
− {^}, {V}, {<}, or {>}: Scroll through various lists and items.
− VOL. (Volume: {^} or {V}): Adjust the receiver or speaker volume while talking.
− {<} k: View the phonebook entry.
− {>} REDIAL: View the redial list.
− {V} CID (Caller ID): View the caller list.
Base unit:
− {^}, {V}, {7}, or {8}: Scroll through various lists and items.
− VOLUME ({^} or {V}): Adjust the speaker volume while talking.
− {7}/{8}: Repeat/skip messages during playback.
Handset Base unit
{^}
{<}
{^}
{V}
{>}
{
7}
{8}
{V}
Date and time (Handset)
1 {MENU}(1)1
2 Enter the current month, date, and year. s {OK}
3 Enter the current hour and minute (12-hour clock format).
4 *: Select “AM” or “PM”. s {SAVE} s {OFF}
Recording your greeting message of the answering system for
the landline (Handset)
You can record your own greeting message instead of using a pre-recorded greeting message.
1 {MENU}(3)2 s {r}: “Yes” s {SELECT}
2 After a beep sounds, hold the handset about 20 cm (8 inches) away and speak clearly into
the microphone (2 minutes max.).
3 Press {STOP} to stop recording. s {OFF}
– 3 –
Link to cell
You can connect your base unit and cellular phone using Bluetooth® wireless technology, so that
you can make or answer cellular calls using your phone system. For more details, please visit our
Web site: http://shop.panasonic.com/bluetooth-phone
L Locate your cellular phone near the base unit. If the cellular phone is too close to the base unit
during a cellular call, you may hear noise. For best performance, we recommend placing the
cellular phone between 0.6 m to 3 m (2 feet to 10 feet) away from the base unit.
1
2
1 Cell line
2 Cell phone service providers
Pairing a Bluetooth cellular phone
1 Base unit:
Press and hold {CELL 1} or {CELL 2} for about 5 seconds.
L After the corresponding CELL indicator on the base unit starts flashing, the rest of the
procedure must be completed within 5 minutes.
2 Your cellular phone:
While the corresponding CELL indicator is flashing, follow the instructions of your cellular
phone to enter the pairing mode.
L Depending on your cellular phone, it may ask you to enter the Bluetooth PIN (default:
“0000”). If your cellular phone shows PassKey confirmation on its display, follow the
directions to proceed.
3 Base unit:
Wait until a long beep sounds.
L It may take more than 10 seconds to complete pairing.
L When the corresponding CELL indicator lights up, the cellular phone is connected to the
base unit. You are ready to make cellular calls.
Note:
L Make sure that your cellular phone is set to connect to this product automatically. Refer to your
cellular phone’s operating instructions.
Trademarks
L The Bluetooth
and any use of such marks by Panasonic Corporation is under license.
L All other trademarks identified herein are the property of their respective owners.
®
word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.,
– 4 –
Loading...