Panasonic KX-TG585SK, KX-TGF372, KX-TGF373, KX-TGF374, KX-TGF375 Operating Instruction

Operating Instructions
Link-to-Cell Bluetooth Convergence Solution
Model No.
KX-TGF372 KX-TGF373 KX-TGF374 KX-TGF375
KX-TG585SK
Before initial use, see “Getting Started” on page 11.
Thank you for purchasing a Panasonic product.
Please read these operating instructions before using the unit and save them for future reference.
Consulte “Guía Rápida Española”, página 83.
For assistance, visit our Web site: www.panasonic.com/support for customers in the U.S.A. or Puerto Rico.
Please register your product: www.panasonic.com/prodreg
TGF37x(en)_1128_ver032.pdf 1 2014/11/28 16:08:38
Introduction
Model composition .......................................4
Accessory information ..................................4
Important Information
For your safety .............................................7
Important safety instructions ........................8
For best performance ...................................8
Other information .........................................9
Specifications .............................................10
Getting Started
Setting up ...................................................11
Controls ......................................................13
Display icons/Indicators .............................14
Language settings ......................................16
Date and time .............................................16
Recording your greeting message .............16
Other settings .............................................16
Link to Cell
Link to cell feature ......................................17
Pairing a cellular phone ..............................17
Link to cell settings .....................................18
Making/Answering Calls Using the Handset
Making cellular calls ...................................21
Making landline calls ..................................21
Answering calls ..........................................22
Useful features during a call .......................22
Power backup operation for landline ..........25
Making/Answering Calls Using the Base Unit
Making cellular calls ...................................27
Making landline calls ..................................27
Answering calls ..........................................28
Useful features during a call .......................28
Intercom
Intercom .....................................................31
Call Block
Using the MCALL BLOCKN button .............32
Storing unwanted callers ............................32
Phonebook
Phonebook .................................................35
Speed dial ..................................................38
Programming
Menu list .....................................................40
Alarm ..........................................................49
Silent mode ................................................50
Baby monitor ..............................................51
Other programming ....................................53
Registering a unit .......................................53
Caller ID Service
Using Caller ID service ...............................54
Caller list ....................................................54
Using Bluetooth® Devices
Copying phonebook from a cellular phone
(phonebook transfer) ..................................57
Link to Cell app ..........................................58
Text message (SMS) alert .........................59
Alert settings for your DECT phone ...........59
Using a Bluetooth wireless headset (optional)
for landline calls .........................................60
Answering System for Landline
Answering system for landline ...................62
Turning the answering system on/off .........62
Greeting message ......................................62
Listening to messages ...............................63
Advanced new message alerting
features ......................................................65
Remote operation .......................................66
Answering system settings .........................67
Useful Information
Voicemail service for landline .....................69
Wall mounting ............................................70
Error messages ..........................................72
Troubleshooting .........................................73
FCC and other information .........................81
Guía Rápida Española
Guía Rápida Española ...............................83
Appendix
Customer services .....................................93
Warranty (For United States and Puerto
Rico) ...........................................................94
Index
2

Table of Contents

TGF37x(en)_1128_ver032.pdf 2 2014/11/28 16:08:38
Index...........................................................96
3
Table of Contents
TGF37x(en)_1128_ver032.pdf 3 2014/11/28 16:08:38

Model composition

Series Model No.
Base unit Handset
Part No. Part No. Quantity
KX-TGF370 series
KX-TGF372 KX-TGF370 KX-TGFA30 2
KX-TGF373 KX-TGF370 KX-TGFA30 3
KX-TGF374 KX-TGF370 KX-TGFA30 4
KX-TGF375 KX-TGF370 KX-TGFA30 5
KX-TG585SK KX-TGF370 KX-TGFA30 5

Accessory information

Supplied accessories
No.
Supplied handset qty.
2 units*13 units*24 units*35 units
*4
Accessory item/Part number Accessory quantity
A AC adaptor/PNLV226Z 1 1 1 1 B
Telephone line cord
*5
1 1 1 1
C Wall mounting adaptor/PNKL1038Z1 1 1 1 1 D
Rechargeable batteries
*6
4 6 8 10
E
Handset cover/PNYNTGA680BR
*7
2 3 4 5
F Belt clip/PNKE1268Z1 2 3 4 5 G
Charger
*8
1 2 3 4
*1 KX-TGF372 *2 KX-TGF373 *3 KX-TGF374 *4 KX-TGF375/KX-TG585SK *5 PQJA10075Y: Black cord, PQJA10075Z: Transparent cord *6 See page 5 for replacement battery information. *7 The handset cover comes attached to the handset. *8 PNLC1040ZS (Silver), PNLC1040ZB (Black)
A
B C D E
4
For assistance, please visit www.panasonic.com/support

Introduction

TGF37x(en)_1128_ver032.pdf 4 2014/11/28 16:08:38
F G
Additional/replacement accessories
Please contact your nearest Panasonic dealer for sales information (page 93).
Accessory item Model number/Specifications
Rechargeable batteries
HHR-4DPA
*1
R To order, please visit
www.panasonic.com/batterystore
Battery type: – Nickel metal hydride (Ni-MH) – 2 x AAA (R03) size for each handset
Headset KX-TCA60, KX-TCA93, KX-TCA400, KX-TCA430
T-adaptor KX-J66
Range extender
KX-TGA405
*2
Key detector
KX-TGA20
*3
*1 Replacement batteries may have a different capacity from that of the supplied batteries. *2 By installing this unit, you can extend the range of your phone system to include areas
where reception was previously not available. This product can be purchased online. Please visit our Web site: www.panasonic.com/RangeExtender
*3 By registering the key detector (4 max.) to a Panasonic Digital Cordless Phone and
attaching it to an easy-to-lose item in advance, you can locate and find the mislaid item to which the key detector is attached. Please visit our Web site: www.panasonic.net/pcc/products/telephone/p/tga20/
Other information
R Design and specifications are subject to change without notice. R The illustrations in these instructions may vary slightly from the actual product.
For assistance, please visit www.panasonic.com/support
5
Introduction
TGF37x(en)_1128_ver032.pdf 5 2014/11/28 16:08:38
Expanding your phone system
Handset (optional): KX-TGFA30
You can expand your phone system by registering optional handsets (6 max.) to a single base unit. R Optional handsets may be a different color
from that of the supplied handsets.
Bluetooth® devices
You can expand your phone system by pairing the following units to a single base unit.
Your Bluetooth cellular phone*1: 2 max. (for cellular calls: page 17)
Your Bluetooth headset*1: 1 max. (for a wireless hands-free conversation: page 60)
*1 Your cellular phone and headset must be Bluetooth wireless technology compatible. For
more details and the list of compatible cellular phones, please visit our Web site: www.panasonic.com/link2cell
Trademarks
R The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.,
and any use of such marks by Panasonic Corporation is under license.
R iPhone is a registered trademark of Apple Inc. R Android is a trademark of Google Inc. R Gmail, Google Calendar are trademarks of Google Inc. R Facebook is trademark of Facebook, Inc. R Twitter is trademark of Twitter Inc. R Instagram is trademark of Instagram, Inc. R BlackBerry® is owned by Research In Motion Limited and is registered in the United States
and may be pending or registered in other countries. Panasonic is not endorsed, sponsored, affiliated with or otherwise authorized by Research In Motion Limited.
R All other trademarks identified herein are the property of their respective owners.
6
For assistance, please visit www.panasonic.com/support
Introduction
TGF37x(en)_1128_ver032.pdf 6 2014/11/28 16:08:38

For your safety

To prevent severe injury and loss of life/ property, read this section carefully before using the product to ensure proper and safe operation of your product.
WARNING
Power connection
R Use only the power source marked on the
product.
R Do not overload power outlets and
extension cords. This can result in the risk of fire or electric shock.
R Completely insert the AC adaptor/power
plug into the power outlet. Failure to do so may cause electric shock and/or excessive heat resulting in a fire.
R Regularly remove any dust, etc. from the
AC adaptor/power plug by pulling it from the power outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation defect from moisture, etc. resulting in a fire.
R Unplug the product from power outlets if it
emits smoke, an abnormal smell, or makes an unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped emitting and contact us at www.panasonic.com/contactinfo
R Unplug from power outlets and never touch
the inside of the product if its casing has been broken open.
R Never touch the plug with wet hands.
Danger of electric shock exists.
Installation
R To prevent the risk of fire or electrical
shock, do not expose the product to rain or any type of moisture.
R Do not place or use this product near
automatically controlled devices such as automatic doors and fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an accident.
R Do not allow the AC adaptor or telephone
line cord to be excessively pulled, bent or placed under heavy objects.
Operating safeguards
R Unplug the product from power outlets
before cleaning. Do not use liquid or aerosol cleaners.
R Do not disassemble the product. R Do not spill liquids (detergents, cleansers,
etc.) onto the telephone line cord plug, or allow it to become wet at all. This may cause a fire. If the telephone line cord plug becomes wet, immediately pull it from the telephone wall jack, and do not use.
Medical
R Consult the manufacturer of any personal
medical devices, such as pacemakers or hearing aids, to determine if they are adequately shielded from external RF (radio frequency) energy. (The product operates in the frequency range of
1.92 GHz to 1.93 GHz, and the RF transmission power is 115 mW (max.).)
R Do not use the product in health care
facilities if any regulations posted in the area instruct you not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.
CAUTION
Installation and location
R Never install telephone wiring during an
electrical storm.
R Never install telephone line jacks in wet
locations unless the jack is specifically designed for wet locations.
R Never touch uninsulated telephone wires or
terminals unless the telephone line has been disconnected at the network interface.
R Use caution when installing or modifying
telephone lines.
R The AC adaptor is used as the main
disconnect device. Ensure that the AC outlet is installed near the product and is easily accessible.
For assistance, please visit www.panasonic.com/support
7

Important Information

TGF37x(en)_1128_ver032.pdf 7 2014/11/28 16:08:38
R This product is unable to make calls when:
– the handset batteries need recharging or
have failed.
– there is a power failure.
Battery
R We recommend using the batteries noted
on page 5. USE ONLY rechargeable
Ni-MH batteries AAA (R03) size.
R Do not mix old and new batteries. R Do not open or mutilate the batteries.
Released electrolyte from the batteries is corrosive and may cause burns or injury to the eyes or skin. The electrolyte is toxic and may be harmful if swallowed.
R Exercise care when handling the batteries.
Do not allow conductive materials such as rings, bracelets, or keys to touch the batteries, otherwise a short circuit may cause the batteries and/or the conductive material to overheat and cause burns.
R Charge the batteries provided with or
identified for use with this product only, in accordance with the instructions and limitations specified in this manual.
R Only use a compatible base unit (or
charger) to charge the batteries. Do not tamper with the base unit (or charger). Failure to follow these instructions may cause the batteries to swell or explode.
Attention:
A nickel metal hydride battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY (1-800-822-8837) for information on how to recycle this battery.

Important safety instructions

When using your product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
1. Do not use this product near water for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.
SAVE THESE INSTRUCTIONS

For best performance

Base unit location/avoiding noise
The base unit and other compatible Panasonic units use radio waves to communicate with each other. R For maximum coverage and noise-free
communications, place your base unit: – at a convenient, high, and central
location with no obstructions between the handset and base unit in an indoor environment.
– away from electronic appliances such as
TVs, radios, personal computers, wireless devices, or other phones.
– facing away from radio frequency
transmitters, such as external antennas of mobile phone cell stations. (Avoid putting the base unit on a bay window or near a window.)
R Coverage and voice quality depends on the
local environmental conditions.
8
For assistance, please visit www.panasonic.com/support
Important Information
TGF37x(en)_1128_ver032.pdf 8 2014/11/28 16:08:38
R If the reception for a base unit location is
not satisfactory, move the base unit to another location for better reception.
Environment
R Keep the product away from electrical noise
generating devices, such as fluorescent lamps and motors.
R The product should be kept free from
excessive smoke, dust, high temperature, and vibration.
R The product should not be exposed to
direct sunlight.
R Do not place heavy objects on top of the
product.
R When you leave the product unused for a
long period of time, unplug the product from the power outlet.
R The product should be kept away from heat
sources such as heaters, kitchen stoves, etc. It should not be placed in rooms where the temperature is less than 0 °C (32 °F) or greater than 40 °C (104 °F). Damp basements should also be avoided.
R The maximum calling distance may be
shortened when the product is used in the following places: Near obstacles such as hills, tunnels, underground, near metal objects such as wire fences, etc.
R Operating the product near electrical
appliances may cause interference. Move away from the electrical appliances.
Routine care
R Wipe the outer surface of the product
with a soft moist cloth.
R Do not use benzine, thinner, or any
abrasive powder.

Other information

CAUTION: Risk of explosion if battery is
replaced by an incorrect type. Dispose of used batteries according to the instructions.
Notice for product disposal, transfer, or return
R This product can store your private/
confidential information. To protect your privacy/confidentiality, we recommend that you erase information such as phonebook or caller list entries from the memory before you dispose of, transfer, or return the product.
Notice
For assistance, please visit www.panasonic.com/support
9
Important Information
TGF37x(en)_1128_ver032.pdf 9 2014/11/28 16:08:39

Specifications

R Standard:
DECT 6.0 (Digital Enhanced Cordless Telecommunications 6.0) Bluetooth wireless technology 2.1
R Frequency range:
1.92 GHz to 1.93 GHz (DECT)
2.402 GHz to 2.48 GHz (Bluetooth)
R RF transmission power:
115 mW (max.)
R Power source:
120 V AC, 60 Hz
R Power consumption:
Base unit:
Standby: Approx. 1.2 W Maximum: Approx. 4.5 W
Charger:
Standby: Approx. 0.1 W Maximum: Approx. 1.8 W
R Operating conditions:
0 °C – 40 °C (32 °F – 104 °F), 20 % – 80 % relative air humidity (dry)
10
For assistance, please visit www.panasonic.com/support
Important Information
TGF37x(en)_1128_ver032.pdf 10 2014/11/28 16:08:39

Setting up

Connections
R If you do not connect the telephone line
cord and use only cellular lines, set the cellular line only mode to use this unit more conveniently (page 19).
n Base unit
Connect the AC adaptor to the unit by pressing the plug firmly. Fasten the cord by hooking it. Connect the AC adaptor to the power outlet. Connect the telephone line cord to the unit, then to the single-line telephone jack (RJ11C) until you hear a click. A DSL/ADSL filter (not supplied) is required if you have a DSL/ADSL service.
Note:
R Use only the supplied Panasonic AC
adaptor PNLV226.
1
2
5
3
4
4
n Charger
Connect the AC adaptor to the power outlet.
1
Battery installation
R USE ONLY rechargeable Ni-MH batteries
AAA (R03) size (
1
).
R Do NOT use alkaline/manganese/Ni-Cd
batteries.
R Confirm correct polarities (
, ).
1
R Follow the directions on the display to set
up the unit.
For assistance, please visit www.panasonic.com/support
11

Getting Started

TGF37x(en)_1128_ver032.pdf 11 2014/11/28 16:08:39
Battery charging
Charge for about 7 hours. R Confirm Charging” is displayed (
1
).
R When the batteries are fully charged,
Fully charged” is displayed.
1
Note when setting up
Note for connections
R The AC adaptor must remain connected at
all times. (It is normal for the adaptor to feel warm during use.)
R The AC adaptor should be connected to a
vertically oriented or floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected.
Note for battery installation
R Use the supplied rechargeable batteries.
For replacement, we recommend using the Panasonic rechargeable batteries noted on page 5, 8.
Note for battery charging
R It is normal for the handset to feel warm
during charging.
R Clean the charge contacts of the handset,
base unit, and charger with a soft and dry cloth once a month. Before cleaning the unit, disconnect from power outlets and any telephone line cords. Clean more often if
the unit is exposed to grease, dust, or high humidity.
Battery level
Icon Battery level
High
Medium
Low
Needs charging.
Empty
Panasonic Ni-MH battery performance (supplied batteries)
Operation Operating time
In continuous use
13 hours max.
*1
Not in use (standby)
12 days max.
*1
*1 If eco mode is on.
Note:
R Actual battery performance depends on
usage and ambient environment.
Intelligent eco mode
This feature automatically reduces handset power consumption by suppressing handset transmission power when the handset is close to the base unit.
R When this feature is activated,
is
displayed. However, during a cellular call,
is not displayed even though this
feature is activated.
R Eco mode is turned off when the clarity
booster is activated (page 23).
12
For assistance, please visit www.panasonic.com/support
Getting Started
TGF37x(en)_1128_ver032.pdf 12 2014/11/28 16:08:39

Controls

Handset
I
K
L
H
M
J
A
B
E
D
C
F
G
Belt clip holes Speaker M N (TALK) Headset jack Dial keypad (*: TONE) MZN (SP-PHONE: Speakerphone) Microphone Receiver Display
MOFFN MFLASHN MCALL WAITN MCALL BLOCKN
Charge contacts
n Control type
Soft keys
By pressing a soft key, you can select the feature shown directly above it on the display. After a cellular phone is paired, MCELLN is displayed.
Navigator key
M
DN, MCN, MFN, or MEN: Scroll through
various lists and items.
– VOL. (Volume: MDN or MCN): Adjust the
receiver or speaker volume while talking.
MFN W: View the phonebook entry. – MEN REDIAL: View the redial list. – MCN CID (Caller ID): View the caller list.
Base unit
A
R
B
E
F
D
G
J
H I
K
L
N O
M
P
B C
A
Charge contacts Speaker Display
MHOLDN MREDIALN MPAUSEN MFLASHN MCALL WAITN MZN (SP-PHONE: Speakerphone)
SP-PHONE indicator
For assistance, please visit www.panasonic.com/support
13
Getting Started
TGF37x(en)_1128_ver032.pdf 13 2014/11/28 16:08:39
MERASEN MANSWER ON/OFFN
ANSWER ON/OFF indicator
MLOCATORN MINTERCOMN R You can locate a misplaced handset
by pressing MLOCATORN. MEXITN M N (PLAY/STOP)
Message indicator MCELL 1N CELL 1 indicator MCELL 2N CELL 2 indicator MAPP ALERTSN Desk stand/Wall mounting adaptor
R The adaptor is a removable
attachment for desk stand or wall
mounting use (page 70).
Microphone Dial keypad (*: TONE)
n Control type
Soft keys
By pressing a soft key, you can select the feature shown directly above it on the display.
Navigator key
– M
DN, MCN, M N, or M N: Scroll through
various lists and items.
– VOL. (Volume: MDN or MCN): Adjust the
speaker volume while talking.
M N/M N: Repeat/skip messages
during playback.

Display icons/Indicators

Handset display items
Item Meaning
Within base unit range
Out of base unit range
The landline is in use. R When flashing:
The call is put on hold.
R When flashing rapidly: An
incoming call is now being received.
Item Meaning
A cellular line is in use.
*1
R When flashing:
The cellular call is put on hold.
R When flashing rapidly:
A cellular call is being received.
Eco mode is on.*2 (page 12)
A cellular phone is connected.*1 Ready to make/ receive cellular calls. R When turned off:
A cellular phone is not connected to the base unit. (page 19)
– A cellular call is being
done on that line.
– The cellular line is
selected for the setting.
Noise reduction is set. (page 23)
Equalizer is set. (page 23)
Z Speakerphone is on.
(page 21)
Ringer volume is off.
*3
(page 42, 44)
Silent mode is on. (page 50)
Call sharing mode is off. (page 46)
Alarm is on. (page 49)
Handset number
Battery level
Blocked call (page 32)
Clarity booster is on.
*2
(page 23)
Baby monitor is activated. The name/number displayed next to the icon indicates the monitoring unit. (page 51)
In use
Answering system is being used by another handset or the base unit.
14
For assistance, please visit www.panasonic.com/support
Getting Started
TGF37x(en)_1128_ver032.pdf 14 2014/11/28 16:08:39
Item Meaning
Cell1 in use
Someone is using the corresponding line.
Cell2 in use
C1&C2 in use
Line in use
*1 Corresponding lines (1, 2: cellular line)
are indicated next to the item.
*2 During a cellular call, the item is not
displayed even though the feature is activated.
*3 Corresponding lines (1, 2: cellular line, L:
landline) are indicated next to the item. If all lines are turned off, no line is indicated.
Base unit display items
Item Meaning
Ringer volume is off.
*1
(page 47, 48)
Silent mode is on. (page 50)
Call sharing mode is off. (page 46)
Greeting only” is selected. Caller messages are not recorded. (page 68)
– A cellular call is being
done on that line.
– The cellular line is
selected for the setting.
App alert is temporarily off. (page 60)
Blocked call (page 32)
A Bluetooth headset is connected to the base unit. It is ready for use.
A Bluetooth headset is in use.
In use
Answering system is being used by the handset.
Item Meaning
Cell1 in use
Someone is using the corresponding line.
Cell2 in use
C1&C2 in use
Line in use
*1 Corresponding lines (C1, C2: cellular line,
L: landline) are indicated next to the item. If all lines are turned off, no line is indicated.
CELL indicators on the base unit
The CELL indicators show each cellular line status.
Status Meaning
On A cellular phone is connected.
Ready to make/receive cellular calls.
Flashing – The cellular line is in use.
– Phonebook entries are
being copied from a cellular phone (page 57).
– The base unit is searching
for the paired cellular phone.
– The base unit is pairing a
cellular phone.
– A cellular call is put on hold.
Flashing rapidly
A cellular call is being received.
Light off – A cellular phone is not
paired to the base unit.
– A cellular phone is not
connected to the base unit (page 19).
For assistance, please visit www.panasonic.com/support
15
Getting Started
TGF37x(en)_1128_ver032.pdf 15 2014/11/28 16:08:39

Language settings

Display language
You can select either English orEspañol as the display language. The default setting is English”.
Handset / Base unit
1 MMENUN#110 2 M
bN: Select the desired setting. a
MSAVEN
3 Proceed with the operation for your unit.
Handset: MOFFN Base unit: MEXITN
Voice guidance language
You can select either English orEspañol as the voice guidance language
of the answering system. The default setting is
English”.
Handset
1 MMENUN#112 2 M
bN: Select the desired setting.
3 MSAVEN a MOFFN

Date and time

Handset
1 MMENUN#101 2 Enter the current month, date, and year
by selecting 2 digits for each. Example: July 12, 2015 07 12 15
3 MOKN 4 Enter the current hour and minute
(12-hour clock format) by selecting 2 digits for each. Example: 9:30 09 30
5 *: Select “AM or PM”.
6 MSAVEN a MOFFN
Note:
R When English is selected as the display
language, 12-hour clock format is used. When Spanish is selected, 24-hour clock format is used.

Recording your greeting message

You can record your own greeting message instead of using a pre-recorded greeting message. See page 62 for details.
Handset
1 MMENUN#302 2 M
bN: “Yes” a MSELECTN
3 Record a greeting message. a MSTOPN
a MOFFN

Other settings

Dialing mode
If you cannot make calls, change this setting according to your telephone line service. The default setting is Tone”.
Tone: For tone dial service.Pulse: For rotary/pulse dial service.
Handset
1 MMENUN#120 2 M
bN: Select the desired setting.
3 MSAVEN a MOFFN
16
For assistance, please visit www.panasonic.com/support
Getting Started
TGF37x(en)_1128_ver032.pdf 16 2014/11/28 16:08:39

Link to cell feature

You can connect your base unit and cellular phone using Bluetooth wireless technology, so that you can make or answer cellular calls using your phone system. This allows you to: – use the unit to talk on cellular calls even if
some areas of your home have poor cellular reception, simply by placing your cellular phone in an area with good reception.
– talk on cellular calls even if your cellular
phone is in your pocket or bag.
– enjoy cordless cellular calls even if your
cellular phone plugged in and charging.
Important:
R Your cellular phone must support the
Hands Free Profile (HFP) specification.
R You may pair 2 cellular phones and 1
headset.
R The unit can be used to talk on 2 lines at
the same time (for example, 2 cellular lines, or the landline and 1 cellular line).
R Only 2 Bluetooth devices can be used with
the unit at the same time (for example, 2 cellular lines, or the headset and 1 cellular line).
R Locate your cellular phone near the base
unit. If the cellular phone is too close to the base unit during a cellular call, you may hear noise. For best performance, we recommend placing the cellular phone between 0.6 m to 3 m (2 feet to 10 feet) away from the base unit.

Pairing a cellular phone

Important:
R For more details and the list of compatible
cellular phones, please visit our Web site: www.panasonic.com/link2cell
R Before pairing a Bluetooth enabled cellular
phone to the base unit, make sure that no other Bluetooth device such as a Bluetooth headset is connected to your cellular phone.
1 Base unit:
Press and hold MCELL 1N or MCELL 2N
for a few seconds.
R After the corresponding CELL
indicator on the base unit starts flashing, the rest of the procedure must be completed within 5 minutes.
2 Your cellular phone:
While the corresponding CELL indicator is flashing, follow the instructions of your cellular phone to enter the pairing mode. R Depending on your cellular phone, it
may ask you to enter the Bluetooth PIN (default: 0000”). If your cellular phone shows PassKey confirmation on its display, follow the directions to proceed.
3 Base unit:
Wait until a long beep sounds. R It may take more than 10 seconds
to complete pairing.
R When the corresponding CELL
indicator lights up, the cellular phone is connected to the base unit. You are ready to make cellular calls.
4 MEXITN
Note:
R Make sure that your cellular phone is set
to connect to this product automatically. Refer to your cellular phone’s operating instructions.
R Make sure you cancel your cellular
phone’s current pairing if you want to pair it to the other line (page 17).
R The default setting for the alert feature is
On, so when you pair your cellular phone to the base unit, this feature may be activated (page 59). (This depends on the version and type of cellular phone you are using.)
Unpairing a cellular phone
You can cancel the pairing of a cellular phone that is stored in the base unit.
Handset
1 For CELL 1: MMENUN#6111
For CELL 2: MMENUN#6112
For assistance, please visit www.panasonic.com/support
17

Link to Cell

TGF37x(en)_1128_ver032.pdf 17 2014/11/28 16:08:39
2 MbN: Yes a MSELECTN
R When the cellular phone is unpaired,
the CELL indicator is turned off.
3 MOFFN

Link to cell settings

Selecting which unit receives cellular calls
You can select which unit rings and receives calls for a cellular line. When All” is selected, all handsets and the base unit ring.
Handset
1 For CELL 1: MMENUN#6271
For CELL 2: MMENUN#6272
2 M
bN: Select the desired handset or All.
a MSAVEN
3 MOFFN
Note:
R When you select a specific handset to
receive calls for a cellular line: – other handsets cannot answer the calls. – the base unit can answer the calls even
though it does not ring. However, you can make the base unit ring by adjusting the base unit ringer volume (page 47).
R When you change to All” from other
setting, the base unit ringer volume also returns to the lowest level even if the ringer volume was changed.
R The units selected with this setting have the
alert feature (page 59) applied to them.
Ring as cell mode
Once this feature is turned on, the handset and base unit ring using the same ringer tone as your cellular phone. The following settings are available: – Off: Turn this feature off to use the
ringer tones of the handset and base unit. Caller information is announced depending on the Talking Caller ID setting (page 44).
On (with Talking CID)” (default):
The handset and base unit use your cellular phone’s ringer tone. Caller information is announced even if the Talking Caller ID is turned off.
On (without Talking CID)”: The
handset and base unit use your cellular phone’s ringer tone. Caller information is not announced even if the Talking Caller ID is turned on.
Important:
R To use this feature, your cellular phone
must support Bluetooth in-band ringtone. Refer to your cellular phone’s operating instructions.
Handset
1 For CELL 1: MMENUN#6141
For CELL 2: MMENUN#6142
2 M
bN: Select the desired setting.
3 MSAVEN a MOFFN
Note:
R The units use the preset ringer tones
instead of your cellular phone’s ringer tone when a cellular call is being received if: – your cellular phone is in silent mode
(depending on your cellular phone). – the base unit is in use. – 2 handsets are sharing a landline call.
R If your cellular phone is in silent mode with
On (with Talking CID)” set, the unit announces caller information even when Talking Caller ID is turned off (page 44).
To use the handset ringer tone instead of your cellular phone’s ringer tone
Select Off” in step 2, “Ring as cell mode”, page 18. To change the handset ringer tone for a cellular line, see page 42.
Auto connection to the Bluetooth devices (cellular phones)
After pairing, your Bluetooth devices are connected to the base unit. If you move the
18
For assistance, please visit www.panasonic.com/support
Link to Cell
TGF37x(en)_1128_ver032.pdf 18 2014/11/28 16:08:39
Bluetooth devices out of base unit range, the Bluetooth devices are disconnected from the base unit. This feature allows the base unit to try to reconnect the Bluetooth devices at regular intervals when it returns within base unit range. You can set the interval. The default setting is 1 min”.
Important:
R When 3 Bluetooth devices (2 cellular
phones and 1 headset) are paired to the base unit, only 2 Bluetooth devices can be used with the unit at the same time, and the base unit loses its connection from other Bluetooth devices. To automatically resume the connection to Bluetooth devices, leave the auto connection on.
R Some cellular phones lose connection after
usage, please check the specifications of your cellular phone for more details.
Handset
1 MMENUN#632 2 M
bN: Select the desired setting.
3 MSAVEN a MOFFN
Note:
R Some cellular phones may ask you if you
accept the connection requirement from the base unit. In that case, select Off” in step
2. Check the specifications of your cellular phone.
Connecting/disconnecting the cellular phone manually
If you will not be using the paired cellular phone’s link to cell feature temporarily (for example, you do not want the unit to ring when your cellular line receives a call), you can disconnect your cellular phone from the base unit. If you want to use it again, reconnect the cellular phone to the base unit.
Note:
R After you disconnect a paired cellular
phone from the base unit manually, it will automatically be connected to the base unit in 30 minutes. If you do not use the link to cell feature anymore, unpair the cellular phone (page 18).
R A disconnected cellular phone is not
unpaired from the base unit, so pairing it to the base unit again is unnecessary.
Handset
1 To connect/disconnect:
For CELL 1: MMENUN#6251 For CELL 2: MMENUN#6252 R A long beep sounds.
2 MOFFN
Cellular line only mode (If you do not use the landline)
If you do not use the landline, we recommend setting the unit to the cellular line only mode. The default setting is Off.
Important:
R If you turn on the “Cell line only
mode, disconnect the telephone line cord from the base unit. Otherwise the “Cell line only mode cannot be activated.
Handset
1 MMENUN#157 2 To turn on:
M
bN: On a MSELECTN a MbN: Yes
a MSELECTN
To turn off:
M
bN: Off a MSELECTN
Note:
R Once you set this mode, you can use the
following buttons to make cellular calls: – for the handset, press M
N or MZN
instead of MCELLN (page 21). – for the base unit, press M
ZN without
pressing MCELL 1N or MCELL 2N set for
the cellular line selection (page 20,
27).
R Once you set this mode, the following
features cannot be used: – Landline features (page 48) – Answering system (page 62)
Messages cannot be received. – Voicemail features (page 69)
R After this mode is turned on or off, the base
unit reboots.
For assistance, please visit www.panasonic.com/support
19
Link to Cell
TGF37x(en)_1128_ver032.pdf 19 2014/11/28 16:08:39
– Bluetooth connections from cellular
phones or headset are disconnected. If the auto connection is turned on (page 18), the cellular phones are reconnected.
will be displayed on the handset momentarily. The handset can be used once
is displayed.
When you use the landline again
Before connecting the telephone line to the base unit, select Off” in step 2, “Cellular line only mode (If you do not use the landline)”, page 19.
Cellular line selection
This feature determines which cellular line is selected to make cellular calls when: – you press MCELLN on the handset. – you press M
N or MZN on the handset
while the cellular line only mode is turned on.
– you press M
ZN on the base unit while the
cellular line only mode is turned on.
The following settings are available: – Manual (handset only: default): You can
select the desired cellular line when making a call.
Cellphone 1*1 (base unit default):
CELL 1 is selected.
Cellphone 2*1: CELL 2 is selected.
Handset / Base unit
1 MMENUN#634 2 M
bN: Select the desired setting. a
MSAVEN
3 Proceed with the operation for your unit.
Handset: MOFFN Base unit: MEXITN
*1 After the Bluetooth device is paired, the
device name is displayed.
Storing your area code (for dialing only a 7-digit phone number to make a local call)
You need to add your area code when making cellular calls to a phone number in your area. Once you store your area code, it is automatically added to the beginning of the 7-digit phone number when making cellular calls.
Handset
1 MMENUN#633 2 Enter the 3-digit area code.
R To correct a digit, press MCLEARN.
3 MSAVEN a MOFFN
Changing the Bluetooth PIN (Personal Identification Number)
The PIN is used to pair cellular phones to the base unit. The default PIN is 0000”. To prevent unauthorized access to this product, we recommend that you change the PIN, and keep it confidential.
Important:
R Please make note of your new PIN. The
unit does not reveal the PIN to you. If you forget your PIN, see page 80.
Handset
1 MMENUN#619
R If the unit prompts you to enter the old
PIN (when the default has been changed), enter the current 4-digit PIN.
2 Enter the new 4-digit PIN. a MOKN 3 Enter the new 4-digit PIN again. a
MSAVEN
4 MOFFN
20
For assistance, please visit www.panasonic.com/support
Link to Cell
TGF37x(en)_1128_ver032.pdf 20 2014/11/28 16:08:39

Making cellular calls

Important:
R The unit can be used to talk on 2 lines at
the same time (for example, 2 cellular lines, or the landline and 1 cellular line).
R Only 2 Bluetooth devices can be used with
the unit at the same time (for example, 2 cellular lines, or the headset and 1 cellular line).
R Before making calls, confirm that the
corresponding
on the handset is
displayed (page 14).
1 Lift the handset and dial the phone
number.
R To correct a digit, press MCLEARN.
2 MCELLN
R The unit starts dialing when:
– only 1 cellular phone is paired. – a specific line is set to make cellular
calls (page 20).
Go to step 4.
3 M
bN: Select the desired cellular phone. a
MSELECTN
4 When you finish talking, press MOFFN or
place the handset on the base unit or charger.
Note:
R To switch to the speaker, press MZN.
To switch back to the receiver, press MZN/
M
N.
Adjusting the receiver or speaker volume
Press M
DN or MCN repeatedly while talking.
Note:
R The receiver or speaker volume you set is
kept for each line (landline and cellular lines).
Making a cellular call using the redial list
The last 5 phone numbers dialed are stored in the redial list (each 48 digits max.).
1 M
EN REDIAL
2 MbN: Select the desired phone number. 3 MCELLN
R The unit starts dialing when:
– only 1 cellular phone is paired. – a specific line is set to make cellular
calls (page 20).
4 MbN: Select the desired cellular phone. a
MSELECTN
Erasing a number in the redial list
n When a cellular phone is paired:
1 M
EN REDIAL
2 M
bN: Select the desired phone number.
a MMENUN
3 M
bN: “Erase” a MSELECTN
4 M
bN: “Yes” a MSELECTN
5 MOFFN
n When a cellular phone is not paired:
1 M
EN REDIAL
2 M
bN: Select the desired phone number.
a MERASEN
3 M
bN: “Yes” a MSELECTN
4 MOFFN

Making landline calls

1 Lift the handset and dial the phone
number.
R To correct a digit, press MCLEARN.
2 M
N
3 When you finish talking, press MOFFN or
place the handset on the base unit or charger.
Using the speakerphone
1 Dial the phone number and press M
ZN.
2 When you finish talking, press MOFFN.
Note:
R To switch back to the receiver, press M
ZN/
M
N.
For assistance, please visit www.panasonic.com/support
21

Making/Answering Calls Using the Handset

TGF37x(en)_1128_ver032.pdf 21 2014/11/28 16:08:39
Making a call using the redial list
The last 5 phone numbers dialed are stored in the redial list (each 48 digits max.).
1 M
EN REDIAL
2 M
bN: Select the desired phone number.
3 M
N
Pause (for PBX/long distance service users)
A pause is sometimes required when making calls using a PBX or long distance service. When storing a calling card access number and/or PIN in the phonebook, a pause is also needed (page 38). Example: If you need to dial the line access number “9” when making outside calls with a PBX:
1 9 a M
DN (Pause)
2 Dial the phone number. a M
N
Note:
R A 3.5 second pause is inserted each time
MDN (Pause) is pressed.

Answering calls

1 Lift the handset and press M
N or MZN
when the unit rings. R To answer a cellular call, you can also
press MCELLN.
2 When you finish talking, press MOFFN or
place the handset on the base unit or charger.
Any key answer: You can answer the call by pressing any dial key. Auto talk: You can answer calls simply by lifting the handset (page 45). Temporary handset ringer off: You can turn the ringer off temporarily by pressing M
N.
Adjusting the handset ringer volume
Press M
DN or MCN repeatedly to select the
desired volume while ringing.
Note:
R The ringer volume you set is kept for each
line (landline and cellular lines).

Useful features during a call

Hold
1 Press MMENUN during an outside call. 2 M
bN: “Hold a MSELECTN
3 To release hold on the cellular line:
Press MCELLN.
*1
R Another handset user can take the call
by pressing MCELLN.
*1
*1 If you press MCELLN and the
selection list is displayed, select the desired cellular line and press
MSELECTN.
R The base unit user can take the call by
pressing MCELL 1N or MCELL 2N.
To release hold on the landline:
Press M
N.
R Another handset user can take the call
by pressing M
N.
R The base unit user can take the call by
pressing M
ZN.
Note:
R After holding for 10 minutes, the call is
disconnected.
Mute
1 Press MMUTEN during a call. 2 To return to the call, press MMUTEN.
Note:
R MMUTEN is a soft key visible on the display
during a call.
Flash for landline calls
MFLASHN allows you to use the special features of your host PBX such as transferring an extension call, or accessing optional telephone services.
22
For assistance, please visit www.panasonic.com/support
Making/Answering Calls Using the Handset
TGF37x(en)_1128_ver032.pdf 22 2014/11/28 16:08:40
Note:
R To change the flash time, see page 46.
For call waiting or Call Waiting Caller ID service users
To use call waiting or Call Waiting Caller ID, you must first subscribe with your phone service provider. This feature allows you to receive calls while you are already talking on the phone. If you receive a call while on the phone, you will hear a call waiting tone.
If you subscribe to both Caller ID and Call Waiting with Caller ID services, the 2nd
caller’s information is displayed after you hear the call waiting tone on the handset.
1 Press MCALL WAITN to answer the 2nd
call.
2 To switch between calls, press MCALL
WAITN.
Note:
R Please contact your phone service provider
for details and availability of this service in your area.
Temporary tone dialing for landline calls (for rotary/pulse service users)
Press * (TONE) before entering access numbers which require tone dialing.
Handset clarity booster
This feature can improve sound clarity when the handset is used in an area where there may be interference. During an outside call, this feature is turned on automatically when necessary.
R When this feature is turned on,
is
displayed. However, during a cellular call,
is not displayed even though the
feature is activated.
Handset noise reduction
This feature allows you to hear the voice of the person you are talking to more clearly, by reducing the surrounding noise coming from the other party’s telephone.
1 Press MMENUN while talking. 2 M
bN: “Noise reduction on” orNoise reduction off” a MSELECTN
Note:
R The setting you made is kept for each line
(landline and cellular lines). The default settings are as follows: – for landline: Noise reduction off – for cellular lines: Noise reduction
on
R Depending on the environment where this
handset is being used, this feature may not be effective.
R This feature is not available while using the
speakerphone.
Handset equalizer
This feature clarifies the voice of the person you are talking to, producing a more natural-sounding voice that is easier to hear and understand.
1 Press MMENUN while talking. 2 MbN: “Equalizer” a MSELECTN 3 M
bN: Select the desired setting.
4 Press MOKN to exit.
Note:
R The setting you made is kept for each line
(landline and cellular lines).
R Depending on the condition and quality of
your telephone line, this feature may emphasize existing line noise. If it becomes difficult to hear, turn this feature off.
R This feature is not available while using the
speakerphone.
R When both the Equalizer” setting and
noise reduction are activated,
is
shown on the display.
For assistance, please visit www.panasonic.com/support
23
Making/Answering Calls Using the Handset
TGF37x(en)_1128_ver032.pdf 23 2014/11/28 16:08:40
Call share
You can join an existing outside call.
n While another unit is on a cellular call:
1 To join the conversation, press
MCELLN. R You can join the conversation when:
– only 1 cellular phone is paired. – a specific line is set to make
cellular calls (page 20).
2 M
bN: Select the corresponding cellular
phone. a MSELECTN
n While another unit is on a landline call:
To join the conversation, press M
N.
Note:
R A maximum of 3 parties (including 1 outside
party) can join a conversation using 2 extensions. (3-way conference)
R To prevent other users from joining your
conversations with outside callers, turn call sharing mode off (page 46).
Transferring calls, conference calls
Outside calls can be transferred or a conference call with an outside party can be made between 2 handsets.
1 During an outside call, press MMENUN. 2 MbN: “Intercom” a MSELECTN 3 M
bN: Select the desired unit. a MSELECTN
4 Wait for the paged party to answer.
R If the paged party does not answer,
press MBACKN to return to the outside call.
5 To complete the transfer:
Press MOFFN. To establish a conference call:
MMENUN a M
bN: Conference” a MSELECTN R To leave the conference, press MOFFN.
The other 2 parties can continue the conversation.
R To put the outside call on hold:
MMENUN a M
bN: Hold a
MSELECTN
To resume the conference: MMENUN a MbN: Conference” a MSELECTN
R To cancel the conference: MMENUN a
M
bN: Stop conference a
MSELECTN
You can continue the conversation with the outside caller.
Transferring a cellular call between the handset and a cellular phone
Transferring a cellular call from the handset to a cellular phone
1 Press MMENUN during a cellular call. 2 M
bN: Transfer to cell a MSELECTN R The cellular call is transferred to the
cellular phone.
Note:
R Depending on your cellular phone type, you
may need to set the cellular phone to be ready to talk before transferring. For example, if your cellular phone has a top cover, open it beforehand.
Transferring a cellular call from a cellular phone to the handset
During a conversation using a cellular phone, the call cannot be transferred to the handset by the cellular phone. Perform the following with the handset.
1 During a conversation using a cellular
phone, press MCELLN. R The call is transferred to the handset
when: – only 1 cellular phone is paired. – a specific line is set to make cellular
calls (page 20).
2 M
bN: Select the corresponding cellular phone. a MSELECTN R The call is transferred to the handset.
24
For assistance, please visit www.panasonic.com/support
Making/Answering Calls Using the Handset
TGF37x(en)_1128_ver032.pdf 24 2014/11/28 16:08:40
Answering a 2nd call
If you receive a call while talking on the phone, the interrupt tone sounds (page 44) and the 2nd caller’s information is displayed if you subscribe to Caller ID service (page 54).
Answering a 2nd call during a landline call
1 Press MMENUN during a landline call. 2 M
bN: “Hold a MSELECTN
3 To answer the 2nd call:
Press MCELLN while the 2nd call is being received.
4 To hang up the 2nd call and return to the
1st call (landline call), press MOFFN, then press M
N.
Answering a 2nd call during a cellular call
1 Press MMENUN during a cellular call. 2 M
bN: “Hold a MSELECTN
3 To answer the 2nd call:
Press M
N or MCELLN while the 2nd call
is being received.
4 To hang up the 2nd call and return to the
1st call (cellular call), press MOFFN, then press MCELLN.
*1
*1 If you press MCELLN and the selection list
is displayed, select the desired cellular line and press MSELECTN.

Power backup operation for landline

When a power failure occurs, the charged handset temporarily supplies power to the base unit (power backup mode). This allows you to make and receive landline calls using a handset during a power failure. The base unit will not perform any other functions. However, some functions such as Caller ID and phonebook are available only when using a handset other than the handset supplying
power to the base unit. You can program
Power failure” and the default setting isAuto (page 46).
Important:
R If a handset is not placed on the base unit
when a power failure occurs, Base no power Press OFF” is displayed. After pressing MOFFN on the handset, place it on the base unit to start power backup mode.
R Power backup mode will not work if the
battery level of the power supplying handset is
or .
R Do not lift the power supplying handset
from the base unit during power backup mode.
Panasonic Ni-MH battery performance (supplied batteries) during power backup mode
When the batteries are fully charged, operating time of the handset in power backup mode varies depending on usage. – Continuous use of the handset in power
backup mode: 1.5 hours max.
– Continuous use of the handset other than a
handset in power backup mode: 2 hours max.
– Not in use in power backup mode: 2 hours
max.
Making calls during a power failure
n When only 1 handset is registered:
1 Lift the handset and dial the phone
number.
2 Within 1 minute, place the handset on
the base unit. R Wait until speakerphone is turned
on automatically and the call is made.
3 When the other party answers the call,
keep the handset on the base unit and talk using the speakerphone.
4 When you finish talking, press MOFFN.
For assistance, please visit www.panasonic.com/support
25
Making/Answering Calls Using the Handset
TGF37x(en)_1128_ver032.pdf 25 2014/11/28 16:08:40
n When 2 or more handsets are registered:
You should leave one handset on the base unit for supplying the power, and use another handset for making calls.
Note:
R The range of the base unit is limited during
a power failure. Please use the handset close to the base unit.
Making a call using the redial list
n When only 1 handset is registered:
1 Lift the handset. 2 M
EN REDIAL
3 M
bN: Select the desired phone number.
4 Within 1 minute, place the handset on
the base unit. R Wait until speakerphone is turned
on automatically and the call is made.
n When 2 or more handsets are registered:
You should leave one handset on the base unit for supplying the power, and use another handset for making calls.
Making a call using the phonebook
There must be at least 2 handsets registered to the base unit in order for the phonebook feature to be used during a power failure.
You should leave one handset on the base unit for supplying the power, and use another handset for making calls.
Answering calls during a power failure
n When only 1 handset is registered:
1 When the unit rings, keep the handset
on the base unit and press M
N or
M
ZN.
R Speakerphone is turned on.
2 When you finish talking, press MOFFN.
n When 2 or more handsets are registered:
When the unit rings, use a handset which is not supplying power to the base unit.
R Do not use or lift the handset which is
placed on the base unit during power backup mode.
Note:
R The range of the base unit is limited during
a power failure. Please use the handset close to the base unit.
26
For assistance, please visit www.panasonic.com/support
Making/Answering Calls Using the Handset
TGF37x(en)_1128_ver032.pdf 26 2014/11/28 16:08:40

Making cellular calls

Important:
R The unit can be used to talk on 2 lines at
the same time (for example, 2 cellular lines, or the landline and 1 cellular line).
R Only 2 Bluetooth devices can be used with
the unit at the same time (for example, 2 cellular lines, or the headset and 1 cellular line).
R Before making calls, confirm that the
corresponding CELL indicator on the base unit lights up (page 15).
1 Dial the phone number.
R To correct a digit, press MCLEARN.
2 Press MCELL 1N or MCELL 2N. 3 When the other party answers, speak into
the microphone.
4 When you finish talking, press M
ZN.
Note:
R While on a call, you can switch from the
base unit to the handset: – With the call sharing mode on
(page 46), press MCELLN*1 on the handset. a M
bN: Select the desired cellular phone. a MSELECTN a Press MZN on the base unit.
– If the handset is on the base unit, simply
lift it.
*1 The call is taken when:
– only 1 cellular phone is paired. – a specific line is set to make cellular
calls (page 20).
Adjusting the speaker volume
Press M
DN or MCN repeatedly while talking.
Note:
R The speaker volume you set is kept for
each line (landline and cellular lines).
Making a cellular call using the redial list
The last 10 phone numbers dialed are stored in the redial list (each 48 digits max.).
1 MREDIALN
2 MbN: Select the desired phone number. 3 Press MCELL 1N or MCELL 2N.
Erasing a number in the redial list
1 MREDIALN 2 M
bN: Select the desired phone number.
a MERASEN
3 M
bN: “Yes” a MSELECTN
4 MEXITN

Making landline calls

1 Dial the phone number.
R To correct a digit, press MCLEARN.
2 M
ZN
3 When the other party answers, speak into
the microphone.
4 When you finish talking, press M
ZN.
Note:
R While on a call, you can switch from the
base unit to the handset: – Press M
N on the handset, then press
M
ZN on the base unit with the call
sharing mode on (page 46).
– If the handset is on the base unit, simply
lift it.
Making a call using the redial list
The last 10 phone numbers dialed are stored in the redial list (each 48 digits max.).
1 MREDIALN 2 M
bN: Select the desired phone number.
3 M
ZN
Pause (for PBX/long distance service users)
A pause is sometimes required when making calls using a PBX or long distance service. When storing a calling card access number and/or PIN in the phonebook, a pause is also needed (page 38).
For assistance, please visit www.panasonic.com/support
27

Making/Answering Calls Using the Base Unit

TGF37x(en)_1128_ver032.pdf 27 2014/11/28 16:08:40
Example: If you need to dial the line access number “9” when making outside calls with a PBX:
1 9 a MPAUSEN 2 Dial the phone number. a M
ZN
Note:
R A 3.5 second pause is inserted each time
MPAUSEN is pressed.

Answering calls

1 Press MZN when the unit rings.
R You can also answer the cellular call
by pressing MCELL 1N or MCELL 2N.
2 Speak into the microphone. 3 When you finish talking, press MZN.
Adjusting the base unit ringer volume
Press M
DN or MCN repeatedly to select the
desired volume while ringing.
Note:
R The ringer volume you set is kept for each
line (landline and cellular lines).

Useful features during a call

Hold
1 Press MHOLDN during an outside call. 2 To release hold on the cellular line:
Press MCELL 1N or MCELL 2N. R A handset user can take the call:
MCELLN*1 a M
bN: Select the corresponding cellular phone. a MSELECTN
*1 The call is taken when:
– only 1 cellular phone is paired. – a specific line is set to make
cellular calls (page 20).
To release hold on the landline:
Press MZN.
R A handset user can take the call by
pressing M
N.
Note:
R While a landline call is on hold, the
SP-PHONE indicator flashes.
R After holding for 10 minutes, the call is
disconnected.
Mute
1 Press MMUTEN during a call.
R The SP-PHONE indicator flashes.
2 To return to the call, press MMUTEN.
Note:
R MMUTEN is a soft key visible on the display
during a call.
Flash for landline calls
MFLASHN allows you to use the special features of your host PBX such as transferring an extension call, or accessing optional telephone services.
Note:
R To change the flash time, see page 46.
For call waiting or Call Waiting Caller ID service users
To use call waiting or Call Waiting Caller ID, you must first subscribe with your phone service provider. This feature allows you to receive calls while you are already talking on the phone. If you receive a call while on the phone, you will hear a call waiting tone.
If you subscribe to both Caller ID and Call Waiting with Caller ID services, the 2nd
caller’s information is displayed after you hear the call waiting tone on the base unit.
1 Press MCALL WAITN to answer the 2nd
call.
2 To switch between calls, press MCALL
WAITN.
28
For assistance, please visit www.panasonic.com/support
Making/Answering Calls Using the Base Unit
TGF37x(en)_1128_ver032.pdf 28 2014/11/28 16:08:40
Note:
R Please contact your phone service provider
for details and availability of this service in your area.
Temporary tone dialing for landline calls (for rotary/pulse service users)
Press * (TONE) before entering access numbers which require tone dialing.
Call share
You can join an existing outside call. To select the line that is being used for the call: – for a cellular line press MCELL 1N or MCELL
2N.
– for the landline press MZN.
Note:
R A maximum of 3 parties (including 1 outside
party) can join a conversation using 2 extensions. (3-way conference)
R To prevent other users from joining your
conversations with outside callers, turn call sharing mode off (page 46).
Transferring calls, conference calls
Outside calls can be transferred or a conference call with an outside party can be made between a handset and the base unit.
1 During an outside call, press
MINTERCOMN. When 2 or more handsets are registered:
– To page a specific handset, enter the
handset number.
– To page all handsets, press 0 or wait
for a few seconds.
2 Wait for the paged party to answer.
R If paged party does not answer, press
MINTERCOMN to return to the outside
call.
3 To complete the transfer:
Press M
ZN.
R The outside call is being routed to the
handset.
To establish a conference call:
Press MCONFN. R To leave the conference, press MZN.
The other 2 parties can continue the conversation.
R To put the outside call on hold, press
MHOLDN. To resume the conference,
press MCONFN.
Transferring a cellular call between the base unit and a cellular phone
Transferring a cellular call from the base unit to a cellular phone
During a cellular call, press and hold MCELL 1N or MCELL 2N until the SP-PHONE indicator
goes out. R The cellular call is transferred to the cellular
phone.
Transferring a cellular call from a cellular phone to the base unit
During a conversation using a cellular phone, press MCELL 1N or MCELL 2N. R The cellular call is transferred to the base
unit.
Answering a 2nd call
If you receive a call while talking on the phone, the interrupt tone sounds (page 48) and the 2nd caller’s information is displayed if you subscribe to Caller ID service (page 54 ).
Answering a 2nd call during a landline call
1 Press MHOLDN during a landline call. 2 To answer the 2nd call:
Press MCELL 1N or MCELL 2N.
3 To hang up the 2nd call and return to the
1st call (landline call), press M
ZN 2 times.
For assistance, please visit www.panasonic.com/support
29
Making/Answering Calls Using the Base Unit
TGF37x(en)_1128_ver032.pdf 29 2014/11/28 16:08:40
Answering a 2nd call during a cellular call
1 Press MHOLDN during a cellular call. 2 To answer the 2nd call:
M
ZN, MCELL 1N, or MCELL 2N
3 To hang up the 2nd call and return to the
1st call (cellular call), press M
ZN, then
press MCELL 1N or MCELL 2N.
30
For assistance, please visit www.panasonic.com/support
Making/Answering Calls Using the Base Unit
TGF37x(en)_1128_ver032.pdf 30 2014/11/28 16:08:40
Loading...
+ 70 hidden pages