Panasonic KX-TG585SK, KX-TGF372, KX-TGF373, KX-TGF374, KX-TGF375 Operating Instruction
Operating Instructions
Link-to-Cell Bluetooth Convergence Solution
Model No.
KX-TGF372
KX-TGF373
KX-TGF374
KX-TGF375
KX-TG585SK
Model shown is KX-TGF372.
Before initial use, see “Getting Started”
on page 11.
Thank you for purchasing a Panasonic product.
Please read these operating instructions before using the unit and save them for
future reference.
Consulte “Guía Rápida Española”, página 83.
For assistance, visit our Web site: www.panasonic.com/support for customers in
the U.S.A. or Puerto Rico.
Please register your product: www.panasonic.com/prodreg
TGF37x(en)_1128_ver032.pdf 1 2014/11/28 16:08:38
Introduction
Model composition .......................................4
Accessory information ..................................4
Important Information
For your safety .............................................7
Important safety instructions ........................8
For best performance ...................................8
Other information .........................................9
Specifications .............................................10
Getting Started
Setting up ...................................................11
Controls ......................................................13
Display icons/Indicators .............................14
Language settings ......................................16
Date and time .............................................16
Recording your greeting message .............16
Other settings .............................................16
Link to Cell
Link to cell feature ......................................17
Pairing a cellular phone ..............................17
Link to cell settings .....................................18
Making/Answering Calls Using
the Handset
Making cellular calls ...................................21
Making landline calls ..................................21
Answering calls ..........................................22
Useful features during a call .......................22
Power backup operation for landline ..........25
Making/Answering Calls Using
the Base Unit
Making cellular calls ...................................27
Making landline calls ..................................27
Answering calls ..........................................28
Useful features during a call .......................28
Intercom
Intercom .....................................................31
Call Block
Using the MCALL BLOCKN button .............32
Storing unwanted callers ............................32
Phonebook
Phonebook .................................................35
Speed dial ..................................................38
Programming
Menu list .....................................................40
Alarm ..........................................................49
Silent mode ................................................50
Baby monitor ..............................................51
Other programming ....................................53
Registering a unit .......................................53
Caller ID Service
Using Caller ID service ...............................54
Caller list ....................................................54
Using Bluetooth® Devices
Copying phonebook from a cellular phone
(phonebook transfer) ..................................57
Link to Cell app ..........................................58
Text message (SMS) alert .........................59
Alert settings for your DECT phone ...........59
Using a Bluetooth wireless headset (optional)
for landline calls .........................................60
Answering System for Landline
Answering system for landline ...................62
Turning the answering system on/off .........62
Greeting message ......................................62
Listening to messages ...............................63
Advanced new message alerting
features ......................................................65
Remote operation .......................................66
Answering system settings .........................67
Useful Information
Voicemail service for landline .....................69
Wall mounting ............................................70
Error messages ..........................................72
Troubleshooting .........................................73
FCC and other information .........................81
Guía Rápida Española
Guía Rápida Española ...............................83
Appendix
Customer services .....................................93
Warranty (For United States and Puerto
Rico) ...........................................................94
Index
2
Table of Contents
TGF37x(en)_1128_ver032.pdf 2 2014/11/28 16:08:38
Index...........................................................96
3
Table of Contents
TGF37x(en)_1128_ver032.pdf 3 2014/11/28 16:08:38
Model composition
Series Model No.
Base unit Handset
Part No. Part No. Quantity
KX-TGF370
series
KX-TGF372 KX-TGF370 KX-TGFA30 2
KX-TGF373 KX-TGF370 KX-TGFA30 3
KX-TGF374 KX-TGF370 KX-TGFA30 4
KX-TGF375 KX-TGF370 KX-TGFA30 5
KX-TG585SK KX-TGF370 KX-TGFA30 5
Accessory information
Supplied accessories
No.
Supplied handset qty.
2 units*13 units*24 units*35 units
*4
Accessory item/Part number Accessory quantity
A AC adaptor/PNLV226Z 1 1 1 1
B
Telephone line cord
*5
1 1 1 1
C Wall mounting adaptor/PNKL1038Z1 1 1 1 1
D
Rechargeable batteries
*6
4 6 8 10
E
Handset cover/PNYNTGA680BR
*7
2 3 4 5
F Belt clip/PNKE1268Z1 2 3 4 5
G
Charger
*8
1 2 3 4
*1 KX-TGF372
*2 KX-TGF373
*3 KX-TGF374
*4 KX-TGF375/KX-TG585SK
*5 PQJA10075Y: Black cord, PQJA10075Z: Transparent cord
*6 See page 5 for replacement battery information.
*7 The handset cover comes attached to the handset.
*8 PNLC1040ZS (Silver), PNLC1040ZB (Black)
A
B C D E
4
For assistance, please visit www.panasonic.com/support
Introduction
TGF37x(en)_1128_ver032.pdf 4 2014/11/28 16:08:38
F G
Additional/replacement accessories
Please contact your nearest Panasonic dealer for sales information (page 93).
Accessory item Model number/Specifications
Rechargeable
batteries
HHR-4DPA
*1
R To order, please visit
www.panasonic.com/batterystore
Battery type:
– Nickel metal hydride (Ni-MH)
– 2 x AAA (R03) size for each handset
Headset KX-TCA60, KX-TCA93, KX-TCA400, KX-TCA430
T-adaptor KX-J66
Range extender
KX-TGA405
*2
Key detector
KX-TGA20
*3
*1 Replacement batteries may have a different capacity from that of the supplied batteries.
*2 By installing this unit, you can extend the range of your phone system to include areas
where reception was previously not available. This product can be purchased online. Please
visit our Web site: www.panasonic.com/RangeExtender
*3 By registering the key detector (4 max.) to a Panasonic Digital Cordless Phone and
attaching it to an easy-to-lose item in advance, you can locate and find the mislaid item to
which the key detector is attached. Please visit our Web site:
www.panasonic.net/pcc/products/telephone/p/tga20/
Other information
R Design and specifications are subject to change without notice.
R The illustrations in these instructions may vary slightly from the actual product.
For assistance, please visit www.panasonic.com/support
5
Introduction
TGF37x(en)_1128_ver032.pdf 5 2014/11/28 16:08:38
Expanding your phone system
Handset (optional): KX-TGFA30
You can expand your phone system by
registering optional handsets (6 max.) to a
single base unit.
R Optional handsets may be a different color
from that of the supplied handsets.
Bluetooth® devices
You can expand your phone system by pairing the following units to a single base unit.
Your Bluetooth cellular phone*1: 2 max.
(for cellular calls: page 17)
Your Bluetooth headset*1: 1 max.
(for a wireless hands-free conversation: page 60)
*1 Your cellular phone and headset must be Bluetooth wireless technology compatible. For
more details and the list of compatible cellular phones, please visit our Web site:
www.panasonic.com/link2cell
Trademarks
R The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.,
and any use of such marks by Panasonic Corporation is under license.
R iPhone is a registered trademark of Apple Inc.
R Android is a trademark of Google Inc.
R Gmail, Google Calendar are trademarks of Google Inc.
R Facebook is trademark of Facebook, Inc.
R Twitter is trademark of Twitter Inc.
R Instagram is trademark of Instagram, Inc.
R BlackBerry® is owned by Research In Motion Limited and is registered in the United States
and may be pending or registered in other countries. Panasonic is not endorsed, sponsored,
affiliated with or otherwise authorized by Research In Motion Limited.
R All other trademarks identified herein are the property of their respective owners.
6
For assistance, please visit www.panasonic.com/support
Introduction
TGF37x(en)_1128_ver032.pdf 6 2014/11/28 16:08:38
For your safety
To prevent severe injury and loss of life/
property, read this section carefully before
using the product to ensure proper and safe
operation of your product.
WARNING
Power connection
R Use only the power source marked on the
product.
R Do not overload power outlets and
extension cords. This can result in the risk
of fire or electric shock.
R Completely insert the AC adaptor/power
plug into the power outlet. Failure to do so
may cause electric shock and/or excessive
heat resulting in a fire.
R Regularly remove any dust, etc. from the
AC adaptor/power plug by pulling it from
the power outlet, then wiping with a dry
cloth. Accumulated dust may cause an
insulation defect from moisture, etc.
resulting in a fire.
R Unplug the product from power outlets if it
emits smoke, an abnormal smell, or makes
an unusual noise. These conditions can
cause fire or electric shock. Confirm that
smoke has stopped emitting and contact us
at www.panasonic.com/contactinfo
R Unplug from power outlets and never touch
the inside of the product if its casing has
been broken open.
R Never touch the plug with wet hands.
Danger of electric shock exists.
Installation
R To prevent the risk of fire or electrical
shock, do not expose the product to rain or
any type of moisture.
R Do not place or use this product near
automatically controlled devices such as
automatic doors and fire alarms. Radio
waves emitted from this product may cause
such devices to malfunction resulting in an
accident.
R Do not allow the AC adaptor or telephone
line cord to be excessively pulled, bent or
placed under heavy objects.
Operating safeguards
R Unplug the product from power outlets
before cleaning. Do not use liquid or
aerosol cleaners.
R Do not disassemble the product.
R Do not spill liquids (detergents, cleansers,
etc.) onto the telephone line cord plug, or
allow it to become wet at all. This may
cause a fire. If the telephone line cord plug
becomes wet, immediately pull it from the
telephone wall jack, and do not use.
Medical
R Consult the manufacturer of any personal
medical devices, such as pacemakers or
hearing aids, to determine if they are
adequately shielded from external RF
(radio frequency) energy. (The product
operates in the frequency range of
1.92 GHz to 1.93 GHz, and the RF
transmission power is 115 mW (max.).)
R Do not use the product in health care
facilities if any regulations posted in the
area instruct you not to do so. Hospitals or
health care facilities may be using
equipment that could be sensitive to
external RF energy.
CAUTION
Installation and location
R Never install telephone wiring during an
electrical storm.
R Never install telephone line jacks in wet
locations unless the jack is specifically
designed for wet locations.
R Never touch uninsulated telephone wires or
terminals unless the telephone line has
been disconnected at the network interface.
R Use caution when installing or modifying
telephone lines.
R The AC adaptor is used as the main
disconnect device. Ensure that the AC
outlet is installed near the product and is
easily accessible.
For assistance, please visit www.panasonic.com/support
7
Important Information
TGF37x(en)_1128_ver032.pdf 7 2014/11/28 16:08:38
R This product is unable to make calls when:
– the handset batteries need recharging or
have failed.
– there is a power failure.
Battery
R We recommend using the batteries noted
on page 5. USE ONLY rechargeable
Ni-MH batteries AAA (R03) size.
R Do not mix old and new batteries.
R Do not open or mutilate the batteries.
Released electrolyte from the batteries is
corrosive and may cause burns or injury to
the eyes or skin. The electrolyte is toxic and
may be harmful if swallowed.
R Exercise care when handling the batteries.
Do not allow conductive materials such as
rings, bracelets, or keys to touch the
batteries, otherwise a short circuit may
cause the batteries and/or the conductive
material to overheat and cause burns.
R Charge the batteries provided with or
identified for use with this product only, in
accordance with the instructions and
limitations specified in this manual.
R Only use a compatible base unit (or
charger) to charge the batteries. Do not
tamper with the base unit (or charger).
Failure to follow these instructions may
cause the batteries to swell or explode.
Attention:
A nickel metal hydride battery that is
recyclable powers the product you have
purchased.
Please call 1-800-8-BATTERY
(1-800-822-8837) for information on how to
recycle this battery.
Important safety instructions
When using your product, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock, and
injury to persons, including the following:
1. Do not use this product near water for
example, near a bathtub, washbowl,
kitchen sink, or laundry tub, in a wet
basement or near a swimming pool.
2. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric
shock from lightning.
3. Do not use the telephone to report a gas
leak in the vicinity of the leak.
4. Use only the power cord and batteries
indicated in this manual. Do not dispose of
batteries in a fire. They may explode.
Check with local codes for possible special
disposal instructions.
SAVE THESE INSTRUCTIONS
For best performance
Base unit location/avoiding noise
The base unit and other compatible Panasonic
units use radio waves to communicate with
each other.
R For maximum coverage and noise-free
communications, place your base unit:
– at a convenient, high, and central
location with no obstructions between
the handset and base unit in an indoor
environment.
– away from electronic appliances such as
TVs, radios, personal computers,
wireless devices, or other phones.
– facing away from radio frequency
transmitters, such as external antennas
of mobile phone cell stations. (Avoid
putting the base unit on a bay window or
near a window.)
R Coverage and voice quality depends on the
local environmental conditions.
8
For assistance, please visit www.panasonic.com/support
Important Information
TGF37x(en)_1128_ver032.pdf 8 2014/11/28 16:08:38
R If the reception for a base unit location is
not satisfactory, move the base unit to
another location for better reception.
Environment
R Keep the product away from electrical noise
generating devices, such as fluorescent
lamps and motors.
R The product should be kept free from
excessive smoke, dust, high temperature,
and vibration.
R The product should not be exposed to
direct sunlight.
R Do not place heavy objects on top of the
product.
R When you leave the product unused for a
long period of time, unplug the product from
the power outlet.
R The product should be kept away from heat
sources such as heaters, kitchen stoves,
etc. It should not be placed in rooms where
the temperature is less than 0 °C (32 °F) or
greater than 40 °C (104 °F). Damp
basements should also be avoided.
R The maximum calling distance may be
shortened when the product is used in the
following places: Near obstacles such as
hills, tunnels, underground, near metal
objects such as wire fences, etc.
R Operating the product near electrical
appliances may cause interference. Move
away from the electrical appliances.
Routine care
R Wipe the outer surface of the product
with a soft moist cloth.
R Do not use benzine, thinner, or any
abrasive powder.
Other information
CAUTION: Risk of explosion if battery is
replaced by an incorrect type. Dispose of used
batteries according to the instructions.
Notice for product disposal, transfer,
or return
R This product can store your private/
confidential information. To protect your
privacy/confidentiality, we recommend that
you erase information such as phonebook
or caller list entries from the memory before
you dispose of, transfer, or return the
product.
Notice
For assistance, please visit www.panasonic.com/support
9
Important Information
TGF37x(en)_1128_ver032.pdf 9 2014/11/28 16:08:39
Specifications
R Standard:
DECT 6.0 (Digital Enhanced Cordless
Telecommunications 6.0)
Bluetooth wireless technology 2.1
R Frequency range:
1.92 GHz to 1.93 GHz (DECT)
2.402 GHz to 2.48 GHz (Bluetooth)
R RF transmission power:
115 mW (max.)
R Power source:
120 V AC, 60 Hz
R Power consumption:
Base unit:
Standby: Approx. 1.2 W
Maximum: Approx. 4.5 W
Charger:
Standby: Approx. 0.1 W
Maximum: Approx. 1.8 W
R Operating conditions:
0 °C – 40 °C (32 °F – 104 °F), 20 % – 80 %
relative air humidity (dry)
10
For assistance, please visit www.panasonic.com/support
Important Information
TGF37x(en)_1128_ver032.pdf 10 2014/11/28 16:08:39
Setting up
Connections
R If you do not connect the telephone line
cord and use only cellular lines, set the
cellular line only mode to use this unit more
conveniently (page 19).
n Base unit
Connect the AC adaptor to the unit by
pressing the plug firmly.
Fasten the cord by hooking it.
Connect the AC adaptor to the power
outlet.
Connect the telephone line cord to the
unit, then to the single-line telephone jack
(RJ11C) until you hear a click.
A DSL/ADSL filter (not supplied) is
required if you have a DSL/ADSL service.
Note:
R Use only the supplied Panasonic AC
adaptor PNLV226.
1
2
5
3
4
4
n Charger
Connect the AC adaptor to the power
outlet.
1
Battery installation
R USE ONLY rechargeable Ni-MH batteries
AAA (R03) size (
1
).
R Do NOT use alkaline/manganese/Ni-Cd
batteries.
R Confirm correct polarities (
, ).
1
R Follow the directions on the display to set
up the unit.
For assistance, please visit www.panasonic.com/support
11
Getting Started
TGF37x(en)_1128_ver032.pdf 11 2014/11/28 16:08:39
Battery charging
Charge for about 7 hours.
R Confirm “Charging” is displayed (
1
).
R When the batteries are fully charged,
“Fully charged” is displayed.
1
Note when setting up
Note for connections
R The AC adaptor must remain connected at
all times. (It is normal for the adaptor to feel
warm during use.)
R The AC adaptor should be connected to a
vertically oriented or floor-mounted AC
outlet. Do not connect the AC adaptor to a
ceiling-mounted AC outlet, as the weight of
the adaptor may cause it to become
disconnected.
Note for battery installation
R Use the supplied rechargeable batteries.
For replacement, we recommend using the
Panasonic rechargeable batteries noted on
page 5, 8.
Note for battery charging
R It is normal for the handset to feel warm
during charging.
R Clean the charge contacts of the handset,
base unit, and charger with a soft and dry
cloth once a month. Before cleaning the
unit, disconnect from power outlets and any
telephone line cords. Clean more often if
the unit is exposed to grease, dust, or high
humidity.
Battery level
Icon Battery level
High
Medium
Low
Needs charging.
Empty
Panasonic Ni-MH battery
performance (supplied batteries)
Operation Operating time
In continuous use
13 hours max.
*1
Not in use (standby)
12 days max.
*1
*1 If eco mode is on.
Note:
R Actual battery performance depends on
usage and ambient environment.
Intelligent eco mode
This feature automatically reduces handset
power consumption by suppressing handset
transmission power when the handset is close
to the base unit.
R When this feature is activated,
is
displayed. However, during a cellular call,
is not displayed even though this
feature is activated.
R Eco mode is turned off when the clarity
booster is activated (page 23).
12
For assistance, please visit www.panasonic.com/support
Getting Started
TGF37x(en)_1128_ver032.pdf 12 2014/11/28 16:08:39
Controls
Handset
I
K
L
H
M
J
A
B
E
D
C
F
G
Belt clip holes
Speaker
M N (TALK)
Headset jack
Dial keypad (*: TONE)
MZN (SP-PHONE: Speakerphone)
Microphone
Receiver
Display
MOFFN
MFLASHN MCALL WAITN
MCALL BLOCKN
Charge contacts
n Control type
Soft keys
By pressing a soft key, you can select the
feature shown directly above it on the
display. After a cellular phone is paired,
MCELLN is displayed.
Navigator key
– M
DN, MCN, MFN, or MEN: Scroll through
various lists and items.
– VOL. (Volume: MDN or MCN): Adjust the
receiver or speaker volume while talking.
– MFN W: View the phonebook entry.
– MEN REDIAL: View the redial list.
– MCN CID (Caller ID): View the caller list.
Base unit
A
R
B
E
F
D
G
J
H
I
K
L
N
O
M
P
B C
A
Charge contacts
Speaker
Display
MHOLDN
MREDIALN MPAUSEN
MFLASHN MCALL WAITN
MZN (SP-PHONE: Speakerphone)
SP-PHONE indicator
For assistance, please visit www.panasonic.com/support
13
Getting Started
TGF37x(en)_1128_ver032.pdf 13 2014/11/28 16:08:39
MERASEN
MANSWER ON/OFFN
ANSWER ON/OFF indicator
MLOCATORN MINTERCOMN
R You can locate a misplaced handset
by pressing MLOCATORN.
MEXITN
M N (PLAY/STOP)
Message indicator
MCELL 1N
CELL 1 indicator
MCELL 2N
CELL 2 indicator
MAPP ALERTSN
Desk stand/Wall mounting adaptor
R The adaptor is a removable
attachment for desk stand or wall
mounting use (page 70).
Microphone
Dial keypad (*: TONE)
n Control type
Soft keys
By pressing a soft key, you can select the
feature shown directly above it on the
display.
Navigator key
– M
DN, MCN, M N, or M N: Scroll through
various lists and items.
– VOL. (Volume: MDN or MCN): Adjust the
speaker volume while talking.
– M N/M N: Repeat/skip messages
during playback.
Display icons/Indicators
Handset display items
Item Meaning
Within base unit range
Out of base unit range
The landline is in use.
R When flashing:
The call is put on hold.
R When flashing rapidly: An
incoming call is now being
received.
Item Meaning
A cellular line is in use.
*1
R When flashing:
The cellular call is put on
hold.
R When flashing rapidly:
A cellular call is being
received.
Eco mode is on.*2 (page 12)
A cellular phone is
connected.*1 Ready to make/
receive cellular calls.
R When turned off:
A cellular phone is not
connected to the base
unit. (page 19)
– A cellular call is being
done on that line.
– The cellular line is
selected for the setting.
Noise reduction is set.
(page 23)
Equalizer is set. (page 23)
Z Speakerphone is on.
(page 21)
Ringer volume is off.
*3
(page 42, 44)
Silent mode is on. (page 50)
Call sharing mode is off.
(page 46)
Alarm is on. (page 49)
Handset number
Battery level
Blocked call (page 32)
Clarity booster is on.
*2
(page 23)
Baby monitor is activated.
The name/number displayed
next to the icon indicates the
monitoring unit. (page 51)
In use
Answering system is being
used by another handset or
the base unit.
14
For assistance, please visit www.panasonic.com/support
Getting Started
TGF37x(en)_1128_ver032.pdf 14 2014/11/28 16:08:39
Item Meaning
Cell1 in
use
Someone is using the
corresponding line.
Cell2 in
use
C1&C2 in
use
Line in
use
*1 Corresponding lines (1, 2: cellular line)
are indicated next to the item.
*2 During a cellular call, the item is not
displayed even though the feature is
activated.
*3 Corresponding lines (1, 2: cellular line, L:
landline) are indicated next to the item. If
all lines are turned off, no line is indicated.
Base unit display items
Item Meaning
Ringer volume is off.
*1
(page 47, 48)
Silent mode is on. (page 50)
Call sharing mode is off.
(page 46)
“Greeting only” is
selected. Caller messages
are not recorded. (page 68)
– A cellular call is being
done on that line.
– The cellular line is
selected for the setting.
App alert is temporarily off.
(page 60)
Blocked call (page 32)
A Bluetooth headset is
connected to the base unit.
It is ready for use.
A Bluetooth headset is in use.
In use
Answering system is being
used by the handset.
Item Meaning
Cell1 in
use
Someone is using the
corresponding line.
Cell2 in
use
C1&C2 in
use
Line in
use
*1 Corresponding lines (C1, C2: cellular line,
L: landline) are indicated next to the item.
If all lines are turned off, no line is
indicated.
CELL indicators on the base unit
The CELL indicators show each cellular line
status.
Status Meaning
On A cellular phone is connected.
Ready to make/receive
cellular calls.
Flashing – The cellular line is in use.
– Phonebook entries are
being copied from a
cellular phone (page 57).
– The base unit is searching
for the paired cellular
phone.
– The base unit is pairing a
cellular phone.
– A cellular call is put on hold.
Flashing
rapidly
A cellular call is being
received.
Light off – A cellular phone is not
paired to the base unit.
– A cellular phone is not
connected to the base unit
(page 19).
For assistance, please visit www.panasonic.com/support
15
Getting Started
TGF37x(en)_1128_ver032.pdf 15 2014/11/28 16:08:39
Language settings
Display language
You can select either “English” or
“Español” as the display language. The
default setting is “English”.
Handset / Base unit
1 MMENUN#110
2 M
bN: Select the desired setting. a
MSAVEN
3 Proceed with the operation for your unit.
Handset: MOFFN
Base unit: MEXITN
Voice guidance language
You can select either “English” or
“Español” as the voice guidance language
of the answering system. The default setting is
“English”.
Handset
1 MMENUN#112
2 M
bN: Select the desired setting.
3 MSAVEN a MOFFN
Date and time
Handset
1 MMENUN#101
2 Enter the current month, date, and year
by selecting 2 digits for each.
Example: July 12, 2015
07 12 15
3 MOKN
4 Enter the current hour and minute
(12-hour clock format) by selecting 2
digits for each.
Example: 9:30
09 30
5 *: Select “AM” or “PM”.
6 MSAVEN a MOFFN
Note:
R When English is selected as the display
language, 12-hour clock format is used.
When Spanish is selected, 24-hour clock
format is used.
Recording your greeting message
You can record your own greeting message
instead of using a pre-recorded greeting
message. See page 62 for details.
Handset
1 MMENUN#302
2 M
bN: “Yes” a MSELECTN
3 Record a greeting message. a MSTOPN
a MOFFN
Other settings
Dialing mode
If you cannot make calls, change this setting
according to your telephone line service. The
default setting is “Tone”.
“Tone”: For tone dial service.
“Pulse”: For rotary/pulse dial service.
Handset
1 MMENUN#120
2 M
bN: Select the desired setting.
3 MSAVEN a MOFFN
16
For assistance, please visit www.panasonic.com/support
Getting Started
TGF37x(en)_1128_ver032.pdf 16 2014/11/28 16:08:39
Link to cell feature
You can connect your base unit and cellular
phone using Bluetooth wireless technology, so
that you can make or answer cellular calls
using your phone system. This allows you to:
– use the unit to talk on cellular calls even if
some areas of your home have poor
cellular reception, simply by placing your
cellular phone in an area with good
reception.
– talk on cellular calls even if your cellular
phone is in your pocket or bag.
– enjoy cordless cellular calls even if your
cellular phone plugged in and charging.
Important:
R Your cellular phone must support the
Hands Free Profile (HFP) specification.
R You may pair 2 cellular phones and 1
headset.
R The unit can be used to talk on 2 lines at
the same time (for example, 2 cellular lines,
or the landline and 1 cellular line).
R Only 2 Bluetooth devices can be used with
the unit at the same time (for example, 2
cellular lines, or the headset and 1 cellular
line).
R Locate your cellular phone near the base
unit. If the cellular phone is too close to the
base unit during a cellular call, you may
hear noise. For best performance, we
recommend placing the cellular phone
between 0.6 m to 3 m (2 feet to 10 feet)
away from the base unit.
Pairing a cellular phone
Important:
R For more details and the list of compatible
cellular phones, please visit our Web site:
www.panasonic.com/link2cell
R Before pairing a Bluetooth enabled cellular
phone to the base unit, make sure that no
other Bluetooth device such as a Bluetooth
headset is connected to your cellular phone.
1 Base unit:
Press and hold MCELL 1N or MCELL 2N
for a few seconds.
R After the corresponding CELL
indicator on the base unit starts
flashing, the rest of the procedure
must be completed within 5 minutes.
2 Your cellular phone:
While the corresponding CELL
indicator is flashing, follow the
instructions of your cellular phone to
enter the pairing mode.
R Depending on your cellular phone, it
may ask you to enter the Bluetooth
PIN (default: “0000”). If your
cellular phone shows PassKey
confirmation on its display, follow
the directions to proceed.
3 Base unit:
Wait until a long beep sounds.
R It may take more than 10 seconds
to complete pairing.
R When the corresponding CELL
indicator lights up, the cellular
phone is connected to the base unit.
You are ready to make cellular calls.
4 MEXITN
Note:
R Make sure that your cellular phone is set
to connect to this product automatically.
Refer to your cellular phone’s operating
instructions.
R Make sure you cancel your cellular
phone’s current pairing if you want to
pair it to the other line (page 17).
R The default setting for the alert feature is
“On”, so when you pair your cellular
phone to the base unit, this feature may
be activated (page 59). (This depends
on the version and type of cellular phone
you are using.)
Unpairing a cellular phone
You can cancel the pairing of a cellular phone
that is stored in the base unit.
Handset
1 For CELL 1: MMENUN#6111
For CELL 2: MMENUN#6112
For assistance, please visit www.panasonic.com/support
17
Link to Cell
TGF37x(en)_1128_ver032.pdf 17 2014/11/28 16:08:39
2 MbN: “Yes” a MSELECTN
R When the cellular phone is unpaired,
the CELL indicator is turned off.
3 MOFFN
Link to cell settings
Selecting which unit receives
cellular calls
You can select which unit rings and receives
calls for a cellular line. When “All” is
selected, all handsets and the base unit ring.
Handset
1 For CELL 1: MMENUN#6271
For CELL 2: MMENUN#6272
2 M
bN: Select the desired handset or “All”.
a MSAVEN
3 MOFFN
Note:
R When you select a specific handset to
receive calls for a cellular line:
– other handsets cannot answer the calls.
– the base unit can answer the calls even
though it does not ring. However, you
can make the base unit ring by adjusting
the base unit ringer volume (page 47).
R When you change to “All” from other
setting, the base unit ringer volume also
returns to the lowest level even if the ringer
volume was changed.
R The units selected with this setting have the
alert feature (page 59) applied to them.
Ring as cell mode
Once this feature is turned on, the handset
and base unit ring using the same ringer tone
as your cellular phone.
The following settings are available:
– “Off”: Turn this feature off to use the
ringer tones of the handset and base unit.
Caller information is announced depending
on the Talking Caller ID setting (page 44).
– “On (with Talking CID)” (default):
The handset and base unit use your cellular
phone’s ringer tone. Caller information is
announced even if the Talking Caller ID is
turned off.
– “On (without Talking CID)”: The
handset and base unit use your cellular
phone’s ringer tone. Caller information is
not announced even if the Talking Caller ID
is turned on.
Important:
R To use this feature, your cellular phone
must support Bluetooth in-band ringtone.
Refer to your cellular phone’s operating
instructions.
Handset
1 For CELL 1: MMENUN#6141
For CELL 2: MMENUN#6142
2 M
bN: Select the desired setting.
3 MSAVEN a MOFFN
Note:
R The units use the preset ringer tones
instead of your cellular phone’s ringer tone
when a cellular call is being received if:
– your cellular phone is in silent mode
(depending on your cellular phone).
– the base unit is in use.
– 2 handsets are sharing a landline call.
R If your cellular phone is in silent mode with
“On (with Talking CID)” set, the unit
announces caller information even when
Talking Caller ID is turned off (page 44).
To use the handset ringer tone
instead of your cellular phone’s
ringer tone
Select “Off” in step 2, “Ring as cell mode”,
page 18.
To change the handset ringer tone for a
cellular line, see page 42.
Auto connection to the Bluetooth
devices (cellular phones)
After pairing, your Bluetooth devices are
connected to the base unit. If you move the
18
For assistance, please visit www.panasonic.com/support
Link to Cell
TGF37x(en)_1128_ver032.pdf 18 2014/11/28 16:08:39
Bluetooth devices out of base unit range, the
Bluetooth devices are disconnected from the
base unit. This feature allows the base unit to
try to reconnect the Bluetooth devices at
regular intervals when it returns within base
unit range. You can set the interval. The
default setting is “1 min”.
Important:
R When 3 Bluetooth devices (2 cellular
phones and 1 headset) are paired to the
base unit, only 2 Bluetooth devices can be
used with the unit at the same time, and the
base unit loses its connection from other
Bluetooth devices. To automatically resume
the connection to Bluetooth devices, leave
the auto connection on.
R Some cellular phones lose connection after
usage, please check the specifications of
your cellular phone for more details.
Handset
1 MMENUN#632
2 M
bN: Select the desired setting.
3 MSAVEN a MOFFN
Note:
R Some cellular phones may ask you if you
accept the connection requirement from the
base unit. In that case, select “Off” in step
2. Check the specifications of your cellular
phone.
Connecting/disconnecting the
cellular phone manually
If you will not be using the paired cellular
phone’s link to cell feature temporarily (for
example, you do not want the unit to ring
when your cellular line receives a call), you
can disconnect your cellular phone from the
base unit. If you want to use it again,
reconnect the cellular phone to the base unit.
Note:
R After you disconnect a paired cellular
phone from the base unit manually, it will
automatically be connected to the base unit
in 30 minutes. If you do not use the link to
cell feature anymore, unpair the cellular
phone (page 18).
R A disconnected cellular phone is not
unpaired from the base unit, so pairing it to
the base unit again is unnecessary.
Handset
1 To connect/disconnect:
For CELL 1: MMENUN#6251
For CELL 2: MMENUN#6252
R A long beep sounds.
2 MOFFN
Cellular line only mode (If you do
not use the landline)
If you do not use the landline, we recommend
setting the unit to the cellular line only mode.
The default setting is “Off”.
Important:
R If you turn on the “Cell line only
mode”, disconnect the telephone line cord
from the base unit. Otherwise the “Cell
line only mode” cannot be activated.
Handset
1 MMENUN#157
2 To turn on:
M
bN: “On” a MSELECTN a MbN: “Yes”
a MSELECTN
To turn off:
M
bN: “Off” a MSELECTN
Note:
R Once you set this mode, you can use the
following buttons to make cellular calls:
– for the handset, press M
N or MZN
instead of MCELLN (page 21).
– for the base unit, press M
ZN without
pressing MCELL 1N or MCELL 2N set for
the cellular line selection (page 20,
27).
R Once you set this mode, the following
features cannot be used:
– Landline features (page 48)
– Answering system (page 62)
Messages cannot be received.
– Voicemail features (page 69)
R After this mode is turned on or off, the base
unit reboots.
For assistance, please visit www.panasonic.com/support
19
Link to Cell
TGF37x(en)_1128_ver032.pdf 19 2014/11/28 16:08:39
– Bluetooth connections from cellular
phones or headset are disconnected. If
the auto connection is turned on
(page 18), the cellular phones are
reconnected.
–
will be displayed on the handset
momentarily. The handset can be used
once
is displayed.
When you use the landline again
Before connecting the telephone line to the
base unit, select “Off” in step 2, “Cellular line
only mode (If you do not use the landline)”,
page 19.
Cellular line selection
This feature determines which cellular line is
selected to make cellular calls when:
– you press MCELLN on the handset.
– you press M
N or MZN on the handset
while the cellular line only mode is turned
on.
– you press M
ZN on the base unit while the
cellular line only mode is turned on.
The following settings are available:
– “Manual” (handset only: default): You can
select the desired cellular line when making
a call.
– “Cellphone 1”*1 (base unit default):
CELL 1 is selected.
– “Cellphone 2”*1: CELL 2 is selected.
Handset / Base unit
1 MMENUN#634
2 M
bN: Select the desired setting. a
MSAVEN
3 Proceed with the operation for your unit.
Handset: MOFFN
Base unit: MEXITN
*1 After the Bluetooth device is paired, the
device name is displayed.
Storing your area code (for
dialing only a 7-digit phone
number to make a local call)
You need to add your area code when making
cellular calls to a phone number in your area.
Once you store your area code, it is
automatically added to the beginning of the
7-digit phone number when making cellular
calls.
Handset
1 MMENUN#633
2 Enter the 3-digit area code.
R To correct a digit, press MCLEARN.
3 MSAVEN a MOFFN
Changing the Bluetooth PIN
(Personal Identification Number)
The PIN is used to pair cellular phones to the
base unit. The default PIN is “0000”. To
prevent unauthorized access to this product,
we recommend that you change the PIN, and
keep it confidential.
Important:
R Please make note of your new PIN. The
unit does not reveal the PIN to you. If you
forget your PIN, see page 80.
Handset
1 MMENUN#619
R If the unit prompts you to enter the old
PIN (when the default has been
changed), enter the current 4-digit PIN.
2 Enter the new 4-digit PIN. a MOKN
3 Enter the new 4-digit PIN again. a
MSAVEN
4 MOFFN
20
For assistance, please visit www.panasonic.com/support
Link to Cell
TGF37x(en)_1128_ver032.pdf 20 2014/11/28 16:08:39
Making cellular calls
Important:
R The unit can be used to talk on 2 lines at
the same time (for example, 2 cellular lines,
or the landline and 1 cellular line).
R Only 2 Bluetooth devices can be used with
the unit at the same time (for example, 2
cellular lines, or the headset and 1 cellular
line).
R Before making calls, confirm that the
corresponding
on the handset is
displayed (page 14).
1 Lift the handset and dial the phone
number.
R To correct a digit, press MCLEARN.
2 MCELLN
R The unit starts dialing when:
– only 1 cellular phone is paired.
– a specific line is set to make cellular
calls (page 20).
Go to step 4.
3 M
bN: Select the desired cellular phone. a
MSELECTN
4 When you finish talking, press MOFFN or
place the handset on the base unit or
charger.
Note:
R To switch to the speaker, press MZN.
To switch back to the receiver, press MZN/
M
N.
Adjusting the receiver or speaker
volume
Press M
DN or MCN repeatedly while talking.
Note:
R The receiver or speaker volume you set is
kept for each line (landline and cellular
lines).
Making a cellular call using the redial
list
The last 5 phone numbers dialed are stored in
the redial list (each 48 digits max.).
1 M
EN REDIAL
2 MbN: Select the desired phone number.
3 MCELLN
R The unit starts dialing when:
– only 1 cellular phone is paired.
– a specific line is set to make cellular
calls (page 20).
4 MbN: Select the desired cellular phone. a
MSELECTN
Erasing a number in the redial list
n When a cellular phone is paired:
1 M
EN REDIAL
2 M
bN: Select the desired phone number.
a MMENUN
3 M
bN: “Erase” a MSELECTN
4 M
bN: “Yes” a MSELECTN
5 MOFFN
n When a cellular phone is not paired:
1 M
EN REDIAL
2 M
bN: Select the desired phone number.
a MERASEN
3 M
bN: “Yes” a MSELECTN
4 MOFFN
Making landline calls
1 Lift the handset and dial the phone
number.
R To correct a digit, press MCLEARN.
2 M
N
3 When you finish talking, press MOFFN or
place the handset on the base unit or
charger.
Using the speakerphone
1 Dial the phone number and press M
ZN.
2 When you finish talking, press MOFFN.
Note:
R To switch back to the receiver, press M
ZN/
M
N.
For assistance, please visit www.panasonic.com/support
21
Making/Answering Calls Using the Handset
TGF37x(en)_1128_ver032.pdf 21 2014/11/28 16:08:39
Making a call using the redial list
The last 5 phone numbers dialed are stored in
the redial list (each 48 digits max.).
1 M
EN REDIAL
2 M
bN: Select the desired phone number.
3 M
N
Pause (for PBX/long distance service
users)
A pause is sometimes required when making
calls using a PBX or long distance service.
When storing a calling card access number
and/or PIN in the phonebook, a pause is also
needed (page 38).
Example: If you need to dial the line access
number “9” when making outside calls with a
PBX:
1 9 a M
DN (Pause)
2 Dial the phone number. a M
N
Note:
R A 3.5 second pause is inserted each time
MDN (Pause) is pressed.
Answering calls
1 Lift the handset and press M
N or MZN
when the unit rings.
R To answer a cellular call, you can also
press MCELLN.
2 When you finish talking, press MOFFN or
place the handset on the base unit or
charger.
Any key answer: You can answer the call by
pressing any dial key.
Auto talk: You can answer calls simply by
lifting the handset (page 45).
Temporary handset ringer off: You can turn
the ringer off temporarily by pressing M
N.
Adjusting the handset ringer volume
Press M
DN or MCN repeatedly to select the
desired volume while ringing.
Note:
R The ringer volume you set is kept for each
line (landline and cellular lines).
Useful features during a call
Hold
1 Press MMENUN during an outside call.
2 M
bN: “Hold” a MSELECTN
3 To release hold on the cellular line:
Press MCELLN.
*1
R Another handset user can take the call
by pressing MCELLN.
*1
*1 If you press MCELLN and the
selection list is displayed, select
the desired cellular line and press
MSELECTN.
R The base unit user can take the call by
pressing MCELL 1N or MCELL 2N.
To release hold on the landline:
Press M
N.
R Another handset user can take the call
by pressing M
N.
R The base unit user can take the call by
pressing M
ZN.
Note:
R After holding for 10 minutes, the call is
disconnected.
Mute
1 Press MMUTEN during a call.
2 To return to the call, press MMUTEN.
Note:
R MMUTEN is a soft key visible on the display
during a call.
Flash for landline calls
MFLASHN allows you to use the special
features of your host PBX such as transferring
an extension call, or accessing optional
telephone services.
22
For assistance, please visit www.panasonic.com/support
Making/Answering Calls Using the Handset
TGF37x(en)_1128_ver032.pdf 22 2014/11/28 16:08:40
Note:
R To change the flash time, see page 46.
For call waiting or Call Waiting
Caller ID service users
To use call waiting or Call Waiting Caller ID,
you must first subscribe with your phone
service provider.
This feature allows you to receive calls while
you are already talking on the phone. If you
receive a call while on the phone, you will hear
a call waiting tone.
If you subscribe to both Caller ID and Call
Waiting with Caller ID services, the 2nd
caller’s information is displayed after you hear
the call waiting tone on the handset.
1 Press MCALL WAITN to answer the 2nd
call.
2 To switch between calls, press MCALL
WAITN.
Note:
R Please contact your phone service provider
for details and availability of this service in
your area.
Temporary tone dialing for
landline calls (for rotary/pulse
service users)
Press * (TONE) before entering access
numbers which require tone dialing.
Handset clarity booster
This feature can improve sound clarity when
the handset is used in an area where there
may be interference. During an outside call,
this feature is turned on automatically when
necessary.
R When this feature is turned on,
is
displayed. However, during a cellular call,
is not displayed even though the
feature is activated.
Handset noise reduction
This feature allows you to hear the voice of
the person you are talking to more clearly, by
reducing the surrounding noise coming from
the other party’s telephone.
1 Press MMENUN while talking.
2 M
bN: “Noise reduction on” or
“Noise reduction off” a
MSELECTN
Note:
R The setting you made is kept for each line
(landline and cellular lines).
The default settings are as follows:
– for landline: “Noise reduction off”
– for cellular lines: “Noise reduction
on”
R Depending on the environment where this
handset is being used, this feature may not
be effective.
R This feature is not available while using the
speakerphone.
Handset equalizer
This feature clarifies the voice of the person
you are talking to, producing a more
natural-sounding voice that is easier to hear
and understand.
1 Press MMENUN while talking.
2 MbN: “Equalizer” a MSELECTN
3 M
bN: Select the desired setting.
4 Press MOKN to exit.
Note:
R The setting you made is kept for each line
(landline and cellular lines).
R Depending on the condition and quality of
your telephone line, this feature may
emphasize existing line noise. If it becomes
difficult to hear, turn this feature off.
R This feature is not available while using the
speakerphone.
R When both the “Equalizer” setting and
noise reduction are activated,
is
shown on the display.
For assistance, please visit www.panasonic.com/support
23
Making/Answering Calls Using the Handset
TGF37x(en)_1128_ver032.pdf 23 2014/11/28 16:08:40
Call share
You can join an existing outside call.
n While another unit is on a cellular call:
1 To join the conversation, press
MCELLN.
R You can join the conversation when:
– only 1 cellular phone is paired.
– a specific line is set to make
cellular calls (page 20).
2 M
bN: Select the corresponding cellular
phone. a MSELECTN
n While another unit is on a landline call:
To join the conversation, press M
N.
Note:
R A maximum of 3 parties (including 1 outside
party) can join a conversation using 2
extensions. (3-way conference)
R To prevent other users from joining your
conversations with outside callers, turn call
sharing mode off (page 46).
Transferring calls, conference
calls
Outside calls can be transferred or a
conference call with an outside party can be
made between 2 handsets.
1 During an outside call, press MMENUN.
2 MbN: “Intercom” a MSELECTN
3 M
bN: Select the desired unit. a MSELECTN
4 Wait for the paged party to answer.
R If the paged party does not answer,
press MBACKN to return to the outside
call.
5 To complete the transfer:
Press MOFFN.
To establish a conference call:
MMENUN a M
bN: “Conference” a
MSELECTN
R To leave the conference, press MOFFN.
The other 2 parties can continue the
conversation.
R To put the outside call on hold:
MMENUN a M
bN: “Hold” a
MSELECTN
To resume the conference: MMENUN
a MbN: “Conference” a MSELECTN
R To cancel the conference: MMENUN a
M
bN: “Stop conference” a
MSELECTN
You can continue the conversation
with the outside caller.
Transferring a cellular call
between the handset and a
cellular phone
Transferring a cellular call from the
handset to a cellular phone
1 Press MMENUN during a cellular call.
2 M
bN: “Transfer to cell” a
MSELECTN
R The cellular call is transferred to the
cellular phone.
Note:
R Depending on your cellular phone type, you
may need to set the cellular phone to be
ready to talk before transferring. For
example, if your cellular phone has a top
cover, open it beforehand.
Transferring a cellular call from a
cellular phone to the handset
During a conversation using a cellular phone,
the call cannot be transferred to the handset
by the cellular phone. Perform the following
with the handset.
1 During a conversation using a cellular
phone, press MCELLN.
R The call is transferred to the handset
when:
– only 1 cellular phone is paired.
– a specific line is set to make cellular
calls (page 20).
2 M
bN: Select the corresponding cellular
phone. a MSELECTN
R The call is transferred to the handset.
24
For assistance, please visit www.panasonic.com/support
Making/Answering Calls Using the Handset
TGF37x(en)_1128_ver032.pdf 24 2014/11/28 16:08:40
Answering a 2nd call
If you receive a call while talking on the phone,
the interrupt tone sounds (page 44) and the
2nd caller’s information is displayed if you
subscribe to Caller ID service (page 54).
Answering a 2nd call during a
landline call
1 Press MMENUN during a landline call.
2 M
bN: “Hold” a MSELECTN
3 To answer the 2nd call:
Press MCELLN while the 2nd call is being
received.
4 To hang up the 2nd call and return to the
1st call (landline call), press MOFFN, then
press M
N.
Answering a 2nd call during a cellular
call
1 Press MMENUN during a cellular call.
2 M
bN: “Hold” a MSELECTN
3 To answer the 2nd call:
Press M
N or MCELLN while the 2nd call
is being received.
4 To hang up the 2nd call and return to the
1st call (cellular call), press MOFFN, then
press MCELLN.
*1
*1 If you press MCELLN and the selection list
is displayed, select the desired cellular
line and press MSELECTN.
Power backup operation for landline
When a power failure occurs, the charged
handset temporarily supplies power to the
base unit (power backup mode). This allows
you to make and receive landline calls using a
handset during a power failure. The base unit
will not perform any other functions. However,
some functions such as Caller ID and
phonebook are available only when using a
handset other than the handset supplying
power to the base unit. You can program
“Power failure” and the default setting is
“Auto” (page 46).
Important:
R If a handset is not placed on the base unit
when a power failure occurs, “Base no
power Press OFF” is displayed. After
pressing MOFFN on the handset, place it on
the base unit to start power backup mode.
R Power backup mode will not work if the
battery level of the power supplying
handset is
or .
R Do not lift the power supplying handset
from the base unit during power backup
mode.
Panasonic Ni-MH battery
performance (supplied batteries)
during power backup mode
When the batteries are fully charged,
operating time of the handset in power backup
mode varies depending on usage.
– Continuous use of the handset in power
backup mode: 1.5 hours max.
– Continuous use of the handset other than a
handset in power backup mode: 2 hours
max.
– Not in use in power backup mode: 2 hours
max.
Making calls during a power
failure
n When only 1 handset is registered:
1 Lift the handset and dial the phone
number.
2 Within 1 minute, place the handset on
the base unit.
R Wait until speakerphone is turned
on automatically and the call is
made.
3 When the other party answers the call,
keep the handset on the base unit and
talk using the speakerphone.
4 When you finish talking, press MOFFN.
For assistance, please visit www.panasonic.com/support
25
Making/Answering Calls Using the Handset
TGF37x(en)_1128_ver032.pdf 25 2014/11/28 16:08:40
n When 2 or more handsets are registered:
You should leave one handset on the base
unit for supplying the power, and use
another handset for making calls.
Note:
R The range of the base unit is limited during
a power failure. Please use the handset
close to the base unit.
Making a call using the redial list
n When only 1 handset is registered:
1 Lift the handset.
2 M
EN REDIAL
3 M
bN: Select the desired phone number.
4 Within 1 minute, place the handset on
the base unit.
R Wait until speakerphone is turned
on automatically and the call is
made.
n When 2 or more handsets are registered:
You should leave one handset on the base
unit for supplying the power, and use
another handset for making calls.
Making a call using the phonebook
There must be at least 2 handsets
registered to the base unit in order for the
phonebook feature to be used during a
power failure.
You should leave one handset on the base
unit for supplying the power, and use another
handset for making calls.
Answering calls during a power
failure
n When only 1 handset is registered:
1 When the unit rings, keep the handset
on the base unit and press M
N or
M
ZN.
R Speakerphone is turned on.
2 When you finish talking, press MOFFN.
n When 2 or more handsets are registered:
When the unit rings, use a handset which is
not supplying power to the base unit.
R Do not use or lift the handset which is
placed on the base unit during power
backup mode.
Note:
R The range of the base unit is limited during
a power failure. Please use the handset
close to the base unit.
26
For assistance, please visit www.panasonic.com/support
Making/Answering Calls Using the Handset
TGF37x(en)_1128_ver032.pdf 26 2014/11/28 16:08:40
Making cellular calls
Important:
R The unit can be used to talk on 2 lines at
the same time (for example, 2 cellular lines,
or the landline and 1 cellular line).
R Only 2 Bluetooth devices can be used with
the unit at the same time (for example, 2
cellular lines, or the headset and 1 cellular
line).
R Before making calls, confirm that the
corresponding CELL indicator on the base
unit lights up (page 15).
1 Dial the phone number.
R To correct a digit, press MCLEARN.
2 Press MCELL 1N or MCELL 2N.
3 When the other party answers, speak into
the microphone.
4 When you finish talking, press M
ZN.
Note:
R While on a call, you can switch from the
base unit to the handset:
– With the call sharing mode on
(page 46), press MCELLN*1 on the
handset. a M
bN: Select the desired
cellular phone. a MSELECTN a Press
MZN on the base unit.
– If the handset is on the base unit, simply
lift it.
*1 The call is taken when:
– only 1 cellular phone is paired.
– a specific line is set to make cellular
calls (page 20).
Adjusting the speaker volume
Press M
DN or MCN repeatedly while talking.
Note:
R The speaker volume you set is kept for
each line (landline and cellular lines).
Making a cellular call using the redial
list
The last 10 phone numbers dialed are stored
in the redial list (each 48 digits max.).
1 MREDIALN
2 MbN: Select the desired phone number.
3 Press MCELL 1N or MCELL 2N.
Erasing a number in the redial list
1 MREDIALN
2 M
bN: Select the desired phone number.
a MERASEN
3 M
bN: “Yes” a MSELECTN
4 MEXITN
Making landline calls
1 Dial the phone number.
R To correct a digit, press MCLEARN.
2 M
ZN
3 When the other party answers, speak into
the microphone.
4 When you finish talking, press M
ZN.
Note:
R While on a call, you can switch from the
base unit to the handset:
– Press M
N on the handset, then press
M
ZN on the base unit with the call
sharing mode on (page 46).
– If the handset is on the base unit, simply
lift it.
Making a call using the redial list
The last 10 phone numbers dialed are stored
in the redial list (each 48 digits max.).
1 MREDIALN
2 M
bN: Select the desired phone number.
3 M
ZN
Pause (for PBX/long distance service
users)
A pause is sometimes required when making
calls using a PBX or long distance service.
When storing a calling card access number
and/or PIN in the phonebook, a pause is also
needed (page 38).
For assistance, please visit www.panasonic.com/support
27
Making/Answering Calls Using the Base Unit
TGF37x(en)_1128_ver032.pdf 27 2014/11/28 16:08:40
Example: If you need to dial the line access
number “9” when making outside calls with a
PBX:
1 9 a MPAUSEN
2 Dial the phone number. a M
ZN
Note:
R A 3.5 second pause is inserted each time
MPAUSEN is pressed.
Answering calls
1 Press MZN when the unit rings.
R You can also answer the cellular call
by pressing MCELL 1N or MCELL 2N.
2 Speak into the microphone.
3 When you finish talking, press MZN.
Adjusting the base unit ringer volume
Press M
DN or MCN repeatedly to select the
desired volume while ringing.
Note:
R The ringer volume you set is kept for each
line (landline and cellular lines).
Useful features during a call
Hold
1 Press MHOLDN during an outside call.
2 To release hold on the cellular line:
Press MCELL 1N or MCELL 2N.
R A handset user can take the call:
MCELLN*1 a M
bN: Select the
corresponding cellular phone. a
MSELECTN
*1 The call is taken when:
– only 1 cellular phone is paired.
– a specific line is set to make
cellular calls (page 20).
To release hold on the landline:
Press MZN.
R A handset user can take the call by
pressing M
N.
Note:
R While a landline call is on hold, the
SP-PHONE indicator flashes.
R After holding for 10 minutes, the call is
disconnected.
Mute
1 Press MMUTEN during a call.
R The SP-PHONE indicator flashes.
2 To return to the call, press MMUTEN.
Note:
R MMUTEN is a soft key visible on the display
during a call.
Flash for landline calls
MFLASHN allows you to use the special
features of your host PBX such as transferring
an extension call, or accessing optional
telephone services.
Note:
R To change the flash time, see page 46.
For call waiting or Call Waiting
Caller ID service users
To use call waiting or Call Waiting Caller ID,
you must first subscribe with your phone
service provider.
This feature allows you to receive calls while
you are already talking on the phone. If you
receive a call while on the phone, you will hear
a call waiting tone.
If you subscribe to both Caller ID and Call
Waiting with Caller ID services, the 2nd
caller’s information is displayed after you hear
the call waiting tone on the base unit.
1 Press MCALL WAITN to answer the 2nd
call.
2 To switch between calls, press MCALL
WAITN.
28
For assistance, please visit www.panasonic.com/support
Making/Answering Calls Using the Base Unit
TGF37x(en)_1128_ver032.pdf 28 2014/11/28 16:08:40
Note:
R Please contact your phone service provider
for details and availability of this service in
your area.
Temporary tone dialing for
landline calls (for rotary/pulse
service users)
Press * (TONE) before entering access
numbers which require tone dialing.
Call share
You can join an existing outside call.
To select the line that is being used for the call:
– for a cellular line press MCELL 1N or MCELL
2N.
– for the landline press MZN.
Note:
R A maximum of 3 parties (including 1 outside
party) can join a conversation using 2
extensions. (3-way conference)
R To prevent other users from joining your
conversations with outside callers, turn call
sharing mode off (page 46).
Transferring calls, conference
calls
Outside calls can be transferred or a
conference call with an outside party can be
made between a handset and the base unit.
1 During an outside call, press
MINTERCOMN.
When 2 or more handsets are
registered:
– To page a specific handset, enter the
handset number.
– To page all handsets, press 0 or wait
for a few seconds.
2 Wait for the paged party to answer.
R If paged party does not answer, press
MINTERCOMN to return to the outside
call.
3 To complete the transfer:
Press M
ZN.
R The outside call is being routed to the
handset.
To establish a conference call:
Press MCONFN.
R To leave the conference, press MZN.
The other 2 parties can continue the
conversation.
R To put the outside call on hold, press
MHOLDN. To resume the conference,
press MCONFN.
Transferring a cellular call
between the base unit and a
cellular phone
Transferring a cellular call from the
base unit to a cellular phone
During a cellular call, press and hold MCELL
1N or MCELL 2N until the SP-PHONE indicator
goes out.
R The cellular call is transferred to the cellular
phone.
Transferring a cellular call from a
cellular phone to the base unit
During a conversation using a cellular phone,
press MCELL 1N or MCELL 2N.
R The cellular call is transferred to the base
unit.
Answering a 2nd call
If you receive a call while talking on the phone,
the interrupt tone sounds (page 48) and the
2nd caller’s information is displayed if you
subscribe to Caller ID service (page 54 ).
Answering a 2nd call during a
landline call
1 Press MHOLDN during a landline call.
2 To answer the 2nd call:
Press MCELL 1N or MCELL 2N.
3 To hang up the 2nd call and return to the
1st call (landline call), press M
ZN 2 times.
For assistance, please visit www.panasonic.com/support
29
Making/Answering Calls Using the Base Unit
TGF37x(en)_1128_ver032.pdf 29 2014/11/28 16:08:40
Answering a 2nd call during a cellular
call
1 Press MHOLDN during a cellular call.
2 To answer the 2nd call:
M
ZN, MCELL 1N, or MCELL 2N
3 To hang up the 2nd call and return to the
1st call (cellular call), press M
ZN, then
press MCELL 1N or MCELL 2N.
30
For assistance, please visit www.panasonic.com/support
Making/Answering Calls Using the Base Unit
TGF37x(en)_1128_ver032.pdf 30 2014/11/28 16:08:40
Loading...