Panasonic KX-TG454SK, KX-TG465SK, KX-TG484SK, KX-TGE260, KX-TGE262 Operating Instruction

...
Operating Instructions
Link-to-Cell Bluetooth Convergence Solution
Model No.
KX-TGE260 KX-TGE262 KX-TGE263
KX-TGE264 KX-TG454SK KX-TG484SK
KX-TGE270
KX-TGE272
KX-TGE273
KX-TGE274
KX-TGE275 KX-TG465SK
Before initial use, see “Getting Started” on page 11.
Thank you for purchasing a Panasonic product.
Please read these operating instructions before using the unit and save them for future reference.
Consulte “Guía Rápida Española”, página 79.
For assistance, visit our Web site: http://www.panasonic.com/help for customers in the U.S.A. or Puerto Rico.
Please register your product: http://www.panasonic.com/prodreg
TGE26x_27x(en)_0123_ver110.pdf 1 2015/01/23 9:57:38
Introduction
Model composition .......................................3
Accessory information ..................................3
Important Information
For your safety .............................................7
Important safety instructions ........................8
For best performance ...................................8
Other information .........................................9
Specifications .............................................10
Getting Started
Setting up ...................................................11
Controls ......................................................13
Display icons/Indicators .............................14
Language settings ......................................16
Date and time .............................................16
Recording your greeting message .............16
Other settings .............................................16
Link to Cell
Link to cell feature ......................................18
Pairing a cellular phone
..............................18
Link to cell settings .....................................19
Making/Answering Calls Using the Handset
Making cellular calls ...................................22
Making landline calls ..................................22
Answering calls ..........................................23
Useful features during a call .......................23
Power back-up operation for landline .........26
Making/Answering Calls Using the Base Unit
Making cellular calls ...................................28
Making landline calls ..................................28
Answering calls ..........................................28
Useful features during a call .......................29
Locator/Intercom
Handset locator ..........................................31
Cell locator .................................................31
Intercom .....................................................31
Phonebook
Phonebook .................................................33
Speed dial ..................................................36
Programming
Menu list .....................................................37
Alarm ..........................................................44
Silent mode ................................................45
Call block ....................................................46
Other programming ....................................47
Registering a unit .......................................48
Caller ID Service
Using Caller ID service ...............................49
Caller list ....................................................49
Using Bluetooth Devices
Copying phonebook from a cellular phone
(phonebook transfer) ..................................52
Text message (SMS) alert .........................53
Using a Bluetooth wireless headset (optional)
for landline calls .........................................54
Answering System for Landline
Answering system for landline ...................56
Turning the answering system on/off .........56
Greeting message ......................................56
Listening to messages ...............................57
Advanced new message alerting
features ......................................................58
Remote operation .......................................60
Answering system settings .........................61
Useful Information
Voice mail service for landline ....................63
Wall mounting ............................................64
Error messages ..........................................67
Troubleshooting .........................................68
FCC and other information .........................76
Guía Rápida Española
Guía Rápida Española ...............................79
Appendix
Customer services .....................................89
Warranty (For United States and Puerto
Rico) ...........................................................90
Index
Index...........................................................92
2

Table of Contents

TGE26x_27x(en)_0123_ver110.pdf 2 2015/01/23 9:57:40

Model composition

n KX-TGE260 series n KX-TGE270 series
R Model shown is KX-TGE262. R Model shown is KX-TGE272.
Series Model No.
Base unit Handset
Part No. Part No. Quantity
KX-TGE260 series
KX-TGE260 KX-TGE260 KX-TGEA20 1
KX-TGE262 KX-TGE260 KX-TGEA20 2
KX-TGE263 KX-TGE260 KX-TGEA20 3
KX-TGE264 KX-TGE260 KX-TGEA20 4
KX-TG454SK KX-TGE260 KX-TGEA20 4
KX-TG484SK KX-TGE260 KX-TGEA20 4
KX-TGE270 s
eries
KX-TGE270 KX-TGE270 KX-TGEA20 1
KX-TGE272 KX-TGE270 KX-TGEA20 2
KX-TGE273 KX-TGE270 KX-TGEA20 3
KX-TGE274 KX-TGE270 KX-TGEA20 4
KX-TGE275 KX-TGE270 KX-TGEA20 5
KX-TG465SK KX-TGE270 KX-TGEA20 5

Accessory information

Supplied accessories
No.
Supplied handset qty.
1 unit*12 units*23 units*34 units*45 units
*5
Accessory item/ O
rder number
Accessory quantity
A AC adaptor/PNLV226Z 1 1 1 1 1
For assistance, please visit http://www.panasonic.com/help
3

Introduction

TGE26x_27x(en)_0123_ver110.pdf 3 2015/01/23 9:57:40
No.
Supplied handset qty.
1 unit*12 units*23 units*34 units*45 units
*5
Accessory item/ Order number
Accessory quantity
B Telephone line cord/
PQJA10075Z
1 1 1 1 1
C
Wall mounting adaptor
*6
1 1 1 1 1
D Rechargeable batteries/
H
HR-4DPA
2 4 6 8 10
E
Handset cover
*7,
*8
1 2 3 4 5
F
Belt clip
*
9
1 2 3 4 5
G
Charger
*10
1 2 3 4
*1 KX-TGE260/KX-TGE270 *2 KX-TGE262/KX-TGE272 *3 KX-TGE263/KX-TGE273 *4 KX-TGE264/KX-TGE274/KX-TG454SK/KX-TG484SK *5 KX-TGE275/KX-TG465SK *6 PNKL1044Z1: White, PNKL1044Z2: Black *7 The handset cover comes attached to the handset. *8 PNYNTGEA20BR: Black, PNYNTGEA20SR: White *9 PNKE1312Z1: White, PNKE1312Z2: Black *10 PNLC1050ZB: Black, PNLC1050ZT: Titanium Black, PNLC1050ZS: Silver
A
B C D E
F G
Additional/replacement accessories
Please contact your nearest Panasonic dealer for sales information (page 89).
Accessory item Order number
Rechargeable b
atteries
HHR-4DPA
*1
R To order, please visit
http://www.panasonic.com/batterystore
Battery type: – Nickel metal hydride (Ni-MH) – 2 x AAA (R03) size for each handset
Headset KX-TCA60, KX-TCA93, KX-TCA400, KX-TCA430
4
For assistance, please visit http://www.panasonic.com/help
Introduction
TGE26x_27x(en)_0123_ver110.pdf 4 2015/01/23 9:57:40
Accessory item Order number
T-adaptor KX-J66
Range extender
KX-TGA405
*2
Key detector
KX-TGA20
*3
*1 Replacement batteries may have a different capacity from that of the supplied batteries. *2 By installing this unit, you can extend the range of your phone system to include areas
where reception was previously not available. This product can be purchased online. Please visit our Web site: http://www.panasonic.com/RangeExtender
*3 By registering the key detector (4 max.) to a Panasonic Digital Cordless Phone and
attaching it to an easy-to-lose item in advance, you can locate and find the mislaid item to which the key detector is attached. Please visit our Web site: http://panasonic.net/pcc/products/telephone/p/tga20/
Other information
R Design and specifications are subject to change without notice. R The illustrations in these instructions may vary slightly from the actual product.
Expanding your phone system
Handset (optional): KX-TGEA20
You can expand your phone system by registering optional handsets (6 max.) to a single base unit. R Optional handsets may be a different color
from that of the supplied handsets.
Bluetooth® devices
You can expand your phone system by pairing the following units to a single base unit.
Your Bluetooth cellular phone
*1
: 2 max.
(for cellular calls: page 18)
Your Bluetooth headset
*
1
: 1 max.
(for a wireless hands-free conversation: page 54)
*1 Your cellular phone and headset must be Bluetooth wireless technology compatible. For
more details and the list of compatible cellular phones, please visit our Web site: http://www.panasonic.com/link2cell
For assistance, please visit http://www.panasonic.com/help
5
Introduction
TGE26x_27x(en)_0123_ver110.pdf 5 2015/01/23 9:57:40
Trademarks
R The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.,
and any use of such marks by Panasonic Corporation is under license.
R All other trademarks identified herein are the property of their respective owners.
6
For assistance, please visit http://www.panasonic.com/help
Introduction
TGE26x_27x(en)_0123_ver110.pdf 6 2015/01/23 9:57:40

For your safety

To prevent severe injury and loss of life/ property, read this section carefully before using the product to ensure proper and safe operation of your product.
WARNING
Power connection
R Use only the power source marked on the
product.
R Do not overload power outlets and
extension cords. This can result in the risk of fire or electric shock.
R Completely insert the AC adaptor/power
plug into the power outlet. Failure to do so may cause electric shock and/or excessive heat resulting in a fire.
R Regularly remove any dust, etc. from the
AC adaptor/power plug by pulling it from the power outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation defect from moisture, etc. resulting in a fire.
R Unplug the product from power outlets if it
emits smoke, an abnormal smell, or makes an unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped emitting and contact us at http://www.panasonic.com/contactinfo
R Unplug from power outlets and never touch
the inside of the product if its casing has been broken open.
R Never touch the plug with wet hands.
Danger of electric shock exists.
Installation
R To prevent the risk of fire or electrical
shock, do not expose the product to rain or any type of moisture.
R Do not place or use this product near
automatically controlled devices such as automatic doors and fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an accident.
R Do not allow the AC adaptor or telephone
line cord to be excessively pulled, bent or placed under heavy objects.
Operating safeguards
R Unplug the product from power outlets
before cleaning. Do not use liquid or aerosol cleaners.
R Do not disassemble the product. R Do not spill liquids (detergents, cleansers,
etc.) onto the telephone line cord plug, or allow it to become wet at all. This may cause a fire. If the telephone line cord plug becomes wet, immediately pull it from the telephone wall jack, and do not use.
Medical
R Consult the manufacturer of any personal
medical devices, such as pacemakers or hearing aids, to determine if they are adequately shielded from external RF (radio frequency) energy. (The product operates in the frequency range of
1.92 GHz to 1.93 GHz, and the RF transmission power is 115 mW (max.).)
R Do not use the product in health care
facilities if any regulations posted in the area instruct you not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.
CAUTION
Installation and location
R Never install telephone wiring during an
electrical storm.
R Never install telephone line jacks in wet
locations unless the jack is specifically designed for wet locations.
R Never touch uninsulated telephone wires or
terminals unless the telephone line has been disconnected at the network interface.
R Use caution when installing or modifying
telephone lines.
R The AC adaptor is used as the main
disconnect device. Ensure that the AC outlet is installed near the product and is easily accessible.
For assistance, please visit http://www.panasonic.com/help
7

Important Information

TGE26x_27x(en)_0123_ver110.pdf 7 2015/01/23 9:57:40
R This product is unable to make calls when:
– the handset batteries need recharging or
have failed.
– there is a power failure.
Battery
R We recommend using the batteries noted
on page 4. USE ONLY rechargeable
Ni-MH batteries AAA (R03) size.
R Do not mix old and new batteries. R Do not open or mutilate the batteries.
Released electrolyte from the batteries is corrosive and may cause burns or injury to the eyes or skin. The electrolyte is toxic and may be harmful if swallowed.
R Exercise care when handling the batteries.
Do not allow conductive materials such as rings, bracelets, or keys to touch the batteries, otherwise a short circuit may cause the batteries and/or the conductive material to overheat and cause burns.
R Charge the batteries provided with or
identified for use with this product only, in accordance with the instructions and limitations specified in this manual.
R Only use a compatible base unit (or
charger) to charge the batteries. Do not tamper with the base unit (or charger). Failure to follow these instructions may cause the batteries to swell or explode.
Attention:
A nickel metal hydride battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY (1-800-822-8837) for information on how to recycle this battery.

Important safety instructions

When using your product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
1. Do not use this product near water for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.
SAVE THESE INSTRUCTIONS

For best performance

Base unit location/avoiding noise
The base unit and other compatible Panasonic units use radio waves to communicate with each other. R For maximum coverage and noise-free
communications, place your base unit: – at a convenient, high, and central
location with no obstructions between the handset and base unit in an indoor environment.
– away from electronic appliances such as
TVs, radios, personal computers, wireless devices, or other phones.
– facing away from radio frequency
transmitters, such as external antennas of mobile phone cell stations. (Avoid putting the base unit on a bay window or near a window.)
R Coverage and voice quality depends on the
local environmental conditions.
8
For assistance, please visit http://www.panasonic.com/help
Important Information
TGE26x_27x(en)_0123_ver110.pdf 8 2015/01/23 9:57:40
R If the reception for a base unit location is
not satisfactory, move the base unit to another location for better reception.
Environment
R Keep the product away from electrical noise
generating devices, such as fluorescent lamps and motors.
R The product should be kept free from
excessive smoke, dust, high temperature, and vibration.
R The product should not be exposed to
direct sunlight.
R Do not place heavy objects on top of the
product.
R When you leave the product unused for a
long period of time, unplug the product from the power outlet.
R The product should be kept away from heat
sources such as heaters, kitchen stoves, etc. It should not be placed in rooms where the temperature is less than 0 °C (32 °F) or greater than 40 °C (104 °F). Damp basements should also be avoided.
R The maximum calling distance may be
shortened when the product is used in the following places: Near obstacles such as hills, tunnels, underground, near metal objects such as wire fences, etc.
R Operating the product near electrical
appliances may cause interference. Move away from the electrical appliances.
Routine care
R Wipe the outer surface of the product
with a soft moist cloth.
R Do not use benzine, thinner, or any
abrasive powder.

Other information

CAUTION: Risk of explosion if battery is
replaced by an incorrect type. Dispose of used batteries according to the instructions.
Notice for product disposal, transfer, or return
R This product can store your private/
confidential information. To protect your privacy/confidentiality, we recommend that you erase information such as phonebook or caller list entries from the memory before you dispose of, transfer, or return the product.
Notice
ENERGY STAR
As an ENERGY STAR® Partner, Panasonic has determined that this product meets the ENERGY STAR guidelines for energy efficiency. ENERGY STAR is a U.S. registered mark.
For assistance, please visit http://www.panasonic.com/help
9
Important Information
TGE26x_27x(en)_0123_ver110.pdf 9 2015/01/23 9:57:40

Specifications

R Standard:
DECT 6.0 (Digital Enhanced Cordless Telecommunications 6.0) Bluetooth wireless technology 2.1
R Frequency range:
1.92 GHz to 1.93 GHz (DECT)
2.402 GHz to 2.48 GHz (Bluetooth)
R RF transmission power:
115 mW (max.)
R Power source:
120 V AC, 60 Hz
R Power consumption:
Base unit:
Standby: Approx. 1.2 W Maximum: Approx. 4.5 W
Charger:
Standby: Approx. 0.1 W Maximum: Approx. 1.8 W
R Operating conditions:
0 °C – 40 °C (32 °F – 104 °F), 20 % – 80 % relative air humidity (dry)
10
For assistance, please visit http://www.panasonic.com/help
Important Information
TGE26x_27x(en)_0123_ver110.pdf 10 2015/01/23 9:57:40

Setting up

Connections
R If you do not connect the telephone line
cord and use only cellular lines, set the cellular line only mode to use this unit more conveniently (page 20).
n Base unit
Connect the AC adaptor to the unit by pressing the plug firmly. Fasten the cord by hooking it. Connect the AC adaptor to the power outlet. Connect the telephone line cord to the unit, then to the single-line telephone jack (RJ11C) until you hear a click. A DSL/ADSL filter (not supplied) is required if you have a DSL/ADSL service.
Note:
R Use only the supplied Panasonic AC
adaptor PNLV226.
1
3
4
4
5
2
n Charger
Connect the AC adaptor to the power outlet.
1
Battery installation
R USE ONLY rechargeable Ni-MH batteries
AAA (R03) size (
1
).
R Do NOT use Alkaline/Manganese/Ni-Cd
batteries.
R Confirm correct polarities (
, ).
1
R Follow the directions on the display to set
up the unit.
For assistance, please visit http://www.panasonic.com/help
11

Getting Started

TGE26x_27x(en)_0123_ver110.pdf 11 2015/01/23 9:57:40
Battery charging
Charge for about 7 hours. R Confirm Charging” is displayed (
1
).
R When the batteries are fully charged,
Fully charged” is displayed.
1
Note when setting up
Note for connections
R The AC adaptor must remain connected at
all times. (It is normal for the adaptor to feel warm during use.)
R The AC adaptor should be connected to a
vertically oriented or floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected.
Note for battery installation
R Use the supplied rechargeable batteries.
For replacement, we recommend using the Panasonic rechargeable batteries noted on page 4, 8.
Note for battery charging
R It is normal for the handset to feel warm
during charging.
R Clean the charge contacts of the handset,
base unit, and charger with a soft and dry cloth once a month. Before cleaning the unit, disconnect from power outlets and any telephone line cords. Clean more often if the unit is exposed to grease, dust, or high humidity.
Battery level
Icon Battery level
High
Medium
Low
Needs charging.
Empty
Panasonic Ni-MH battery performance (supplied batteries)
Operation Operating time
In continuous use
10 hours max.
*1
Not in use (standby)
8 days max.
*
1
*1 If eco mode is on.
Note:
R Actual battery performance depends on
usage and ambient environment.
Intelligent eco mode
This feature automatically reduces handset power consumption by suppressing handset transmission power when the handset is close to the base unit.
R When this feature is activated,
is
displayed. However, during a cellular call,
is not displayed even though this
feature is activated.
R Eco mode is turned off when the clarity
booster is activated (page 24).
12
For assistance, please visit http://www.panasonic.com/help
Getting Started
TGE26x_27x(en)_0123_ver110.pdf 12 2015/01/23 9:57:41

Controls

Handset
A
B
A
C
F
G
E
L
M
N
K
O
B
A
D
H I
J
Ringer indicator Belt clip holes Speaker
MjN/MkN (VOL.: Volume up/down) M N (TALK)
Dial keypad (*: TONE) Headset jack
MZN (SP-PHONE: Speakerphone) MFLASHNMCALL WAITN
Microphone Receiver Display
MOFFN M N (NOISE REDUCTION/Smart
function key)
indicator
Charge contacts
n Control type
Soft keys
By pressing a soft key, you can select the feature shown directly above it on the display. After a cellular phone is paired, MCELLN is displayed.
Navigator key
M
DN, MCN, MFN, or MEN: Scroll through
various lists and items.
(Volume: MDN or MCN): Adjust the
receiver or speaker volume while talking.
MFN W: View the phonebook entry. – MEN REDIAL: View the redial list. – MCN CID (Caller ID): View the caller list.
Base unit
n KX-TGE260 series: page 3
A
HI
M L K
B J
C
D
F
G
E
Charge contacts Speaker HEADSET indicator MANSWER ON/OFFN CELL 1 indicator CELL 2 indicator
For assistance, please visit http://www.panasonic.com/help
13
Getting Started
TGE26x_27x(en)_0123_ver110.pdf 13 2015/01/23 9:57:41
Message counter M N
(PLAY/STOP)
Message indicator
MLOCATES CELLN MHANDSET LOCATORN MjN/MkN (VOL.: Volume up/down) MERASEN M N (Skip) M N (Repeat)
n KX-TGE270 series: page 3
R
LM
P O
BA N
S
C
E
F
D
I
J K
G
H
Charge contacts Speaker
MHOLDN MCONFN MREDIALN MPAUSEN MFLASHN MCALL WAITN MZN (SP-PHONE: Speakerphone)
SP-PHONE indicator HEADSET indicator CELL 1 indicator CELL 2 indicator Message counter M N (PLAY/STOP) Message indicator
MANSWER ON/OFFN MLOCATES CELLN MLOCATORN MINTERCOMN MjN/M
kN (VOL.: Volume up/down) MERASEN MMUTEN MCELL 1
N M
N (Skip)
MCELL 2
N M
N (Repeat)
Microphone Dial keypad (*:
TONE)

Display icons/Indicators

Handset display items
Item Meaning
Within base unit range
Out of base unit range
The landline is in use. R When flashing:
The call is put on hold.
R When flashing rapidly: An
incoming call is now being received.
A cellular line is in use.
*1
R When flashing:
The cellular call is put on hold.
R When flashing rapidly:
A cellular call is being received.
A cellular phone is connected.
*1
Ready to make/
receive cellular calls. R When turned off:
A cellular phone is not connected to the base unit. (page 20)
– A cellular call is being
done on that line.
– The cellular line is
selected for the setting.
Eco mode is on.
*2
(page 12)
Noise reduction is set. (page 24)
Equalizer is set. (page 24)
Z Speakerphone is on.
(
page 22)
Ringer volume is off.
*3
(page 39, 41)
Silent mode is on. (page 45)
14
For assistance, please visit http://www.panasonic.com/help
Getting Started
TGE26x_27x(en)_0123_ver110.pdf 14 2015/01/23 9:57:41
Item Meaning
Call sharing mode is off. (page 43)
Alarm is on. (page 44)
Handset number
Battery level
Blocked call (page 46)
Clarity booster is on.
*2
(page 24)
In use
Answering system is being used by another handset or the base unit.
Cell1 in use
Someone is using the corresponding line.
Cell2 in use
C1&C2 in use
Line in use
*1 Corresponding cellular line(s) is(are)
indicated next to the item.
*2 During a cellular call, the item is not
displayed even though the feature is activated.
*3 Corresponding lines (1, 2: cellular line, L:
landline) are indicated next to the item. If all lines are turned off, no line is indicated.
Base unit display item
Item Meaning
Greeting only” is
selected. Caller messages are not recorded. (page 62)
CELL indicators on the base unit
The CELL indicators show each cellular line status.
Status Meaning
On A cellular phone is connected.
Ready to make/receive cellular calls.
Status Meaning
Flashing – The cellular line is in use.
– Phonebook entries are
being copied from a cellular phone (page 52).
– The base unit is searching
for the paired cellular phone.
– The base unit is pairing a
cellular phone.
– A cellular call is put on hold.
Flashing rapidly
A cellular call is being received.
Light off – A cellular phone is not
paired to the base unit.
– A cellular phone is not
connected to the base unit (page 20).
Bluetooth HEADSET indicator on the base unit
The HEADSET indicator shows the Bluetooth headset status.
Status Meaning
On A Bluetooth headset is
connected to the base unit. Ready to use it.
Flashing – A Bluetooth headset is in
use.
– The base unit is searching
for the paired Bluetooth headset.
– The base unit is pairing a
headset.
– Mute is turned on.
Flashing rapidly
A landline call is being received.
Light off – The Bluetooth headset is
not connected to the base unit.
– A Bluetooth headset is not
paired to the base unit.
For assistance, please visit http://www.panasonic.com/help
15
Getting Started
TGE26x_27x(en)_0123_ver110.pdf 15 2015/01/23 9:57:41

Language settings

Display language
You can select either English orEspañol as the display language. The default setting is English”.
1 MMENUN#110 2 M
bN: Select the desired setting. a
MSAVEN
3 MOFFN
Voice guidance language
You can select either English orEspañol as the voice guidance language
of the answering system. The default setting is
English”.
1 MMENUN#112 2 M
bN: Select the desired setting.
3 MSAVEN a MOFFN

Date and time

1 MMENUN#101 2 Enter the current month, date, and year
by selecting 2 digits for each. Example: July 15, 2014 07 15 14
3 MOKN 4 Enter the current hour and minute
(12-hour clock format) by selecting 2 digits for each. Example: 9:30 09 30
5 *: Select “AM” or “PM”. 6 MSAVEN a MOFFN
Note:
R When English is selected as the display
language, 12-hour clock format is used. When Spanish is selected, 24-hour clock format is used.

Recording your greeting message

You can record your own greeting message instead of using a pre-recorded greeting message. See page 56 for details.
1 MMENUN#302 2 MbN: “Yesa MSELECTN 3 Record a greeting message. a MSTOPN
a MOFFN

Other settings

Smart function key ( key)
The Smart function key (
key) is located
on the bottom of the handset and informs you with its flashing to allow you to activate the following features by simply pressing this key.
n When the indicator flashes rapidly,
you can:
– Answer the call (outside call, intercom).
(page 23, 32) – Stop paging. (page 31) – Stop the alarm sound. (page 45)
n When the indicator flashes slowly in
standby mode, you can:
– Listen to new messages. (page 57) – Listen to new voice mail messages.
(page 64) – View the caller list when there are
missed calls. (page 50) To activate these features, their Smart function key must be “On”. (page 17)
Using the Smart function key ( key)
When the
indicator flashes rapidly/slowly,
p
ress M
N.
R The above features can be activated
depending the situation.
R If you answer a call using the Smart
function key, the speakerphone is activated.
R Even if the handset is placed on the base
unit or charger, the feature can be
16
For assistance, please visit http://www.panasonic.com/help
Getting Started
TGE26x_27x(en)_0123_ver110.pdf 16 2015/01/23 9:57:41
activated. You can talk or listen to new messages without lifting up the handset. If you want to perform further operations, lift up the handset.
R When the unit has new messages, new
voice mail messages, and missed calls, the unit can be operated to play the new messages first, play the new voice mail messages next, and then show the missed calls.
Setting the Smart function key
The Smart function key for the following features must be “On”. – New message” (Default: On)New VM (Default: On) – Missed Call” (Default: Off) The settings can be set for each handset.
1 MMENUN#278 2 M
bN: Select the desired setting and press MSELECTN. R
” is displayed next to the selected
features.
R To cancel a selected feature, press
MSELECTN again. “
” disappears.
3 MSAVEN a MOFFN
Note:
R If the
indicator flashes when the
handset is not placed on the base unit or charger, battery consumption is faster than usual.
Dialing mode
If you cannot make calls, change this setting according to your telephone line service. The default setting is Tone”.
Tone: For tone dial service.Pulse: For rotary/pulse dial service.
1 MMENUN#120 2 M
bN: Select the desired setting.
3 MSAVEN a MOFFN
For assistance, please visit http://www.panasonic.com/help
17
Getting Started
TGE26x_27x(en)_0123_ver110.pdf 17 2015/01/23 9:57:41

Link to cell feature

You can connect your base unit and cellular phone using Bluetooth wireless technology, so that you can make or answer cellular calls using your phone system. This allows you to: – use the unit to talk on cellular calls even if
some areas of your home have poor cellular reception, simply by placing your cellular phone in an area with good reception.
– talk on cellular calls even if your cellular
phone is in your pocket or bag.
– enjoy cordless cellular calls even if your
cellular phone plugged in and charging.
Important:
R Your cellular phone must support the
Hands Free Profile (HFP) specification.
R You may pair 2 cellular phones and 1
headset.
R The unit can be used to talk on 2 lines at
the same time (for example, 2 cellular lines, or the landline and 1 cellular line).
R Only 2 Bluetooth devices can be used with
the unit at the same time (for example, 2 cellular lines, or the headset and 1 cellular line).
R Locate your cellular phone near the base
unit. If the cellular phone is too close to the base unit during a cellular call, you may hear noise. For best performance, we recommend placing the cellular phone between 0.6 m to 3 m (2 feet to 10 feet) away from the base unit.

Pairing a cellular phone

Important:
R For more details and the list of compatible
cellular phones, please visit our Web site: http://www.panasonic.com/link2cell
R Before pairing a Bluetooth enabled cellular
phone to the base unit, make sure that no other Bluetooth device such as a Bluetooth headset is connected to your cellular phone.
1 Handset:
For CELL 1: MMENUN#6241 For CELL 2: MMENUN#6242
R After the corresponding CELL indicator
on the base unit starts flashing, the rest of the procedure must be completed within 5 minutes.
2 Your cellular phone:
While the corresponding CELL indicator is flashing, follow the instructions of your cellular phone to enter the pairing mode. R Depending on your cellular phone, it
may ask you to enter the Bluetooth PIN (default: 0000”). If your cellular phone shows PassKey confirmation on its display, follow the directions to proceed.
3 Handset:
Wait until a long beep sounds. R It may take more than 10 seconds to
complete pairing.
R When the corresponding CELL
indicator lights up, the cellular phone is connected to the base unit. You are ready to make cellular calls.
4 MOFFN
Note:
R Make sure that your cellular phone is set to
connect to this product automatically. Refer to your cellular phone’s operating instructions.
R Make sure you cancel your cellular phone’s
current pairing if you want to pair it to the other line (page 18).
R The default setting for the text message
alert feature is On(no announce)”, so when you pair your cellular phone to the base unit, this feature may be activated (page 53). (This depends on the version and type of cellular phone you are using.)
Unpairing a cellular phone
You can cancel the pairing of a cellular phone that is stored in the base unit.
1 For CELL 1: MMENUN#6111
For CELL 2: MMENUN#6112
2 MbN: “Yesa MSELECTN
R When the cellular phone is unpaired,
the CELL indicator is turned off.
3 MOFFN
18
For assistance, please visit http://www.panasonic.com/help

Link to Cell

TGE26x_27x(en)_0123_ver110.pdf 18 2015/01/23 9:57:41

Link to cell settings

Selecting which unit receives cellular calls
You can select which unit rings and receives calls for a cellular line. When All” is selected, all handsets and the base unit ring.
1 For CELL 1: MMENUN#6271
For CELL 2: MMENUN#6272
2 M
bN: Select the desired handset or All. a MSAVEN
3 MOFFN
Note:
R When you select a specific handset to
receive calls for a cellular line: – other handsets cannot answer the calls. – the base unit can answer the calls even
though it does not ring. However, you
can make the base unit ring by adjusting
the base unit ringer volume (page 39).
(KX-TGE270 series: page 3)
R When you change the setting to All, the
base unit ringer volume also returns to the lowest level even if the ringer volume has been changed.
R The units selected with this setting have the
text message alert feature (page 53) applied to them.
Ring as cell mode
Once this feature is turned on, the handset and base unit ring using the same ringer tone as your cellular phone. The following settings are available: – Off: Turn this feature off to use the
ringer tones of the handset and base unit. Caller information is announced depending on the Talking Caller ID setting (page 41).
On (with Talking CID)” (default):
The handset and base unit use your cellular phone’s ringer tone. Caller information is announced even if the Talking Caller ID is turned off.
On (without Talking CID)”: The
handset and base unit use your cellular phone’s ringer tone. Caller information is
not announced even if the Talking Caller ID is turned on.
Important:
R To use this feature, your cellular phone
must support Bluetooth in-band ringtone. Refer to your cellular phone’s operating instructions.
1 For CELL 1: MMENUN#6141
For CELL 2: MMENUN#6142
2 M
bN: Select the desired setting.
3 MSAVEN a MOFFN
Note:
R The units use the preset ringer tones
(page 41) instead of your cellular phone’s ringer tone when a cellular call is being received if: – your cellular phone is in silent mode
(depending on your cellular phone). – the base unit is in use. – 2 handsets are sharing a landline call.
R If your cellular phone is in silent mode with
On (with Talking CID)” set, the unit announces caller information even when Talking Caller ID is turned off (page 41).
To use the handset ringer tone instead of your cellular phone’s ringer tone
Select Off” in step 2, “Ring as cell mode”, page 19. To change the handset ringer tone for a cellular line, see page 39.
Auto connection to the Bluetooth devices (cellular phones or headset)
After pairing, your Bluetooth devices are connected to the base unit. If you move the Bluetooth devices out of base unit range, the Bluetooth devices are disconnected from the base unit. This feature allows the base unit to try to reconnect the Bluetooth devices at regular intervals when it returns within base unit range. You can set the interval. The default setting is 1 min”.
For assistance, please visit http://www.panasonic.com/help
19
Link to Cell
TGE26x_27x(en)_0123_ver110.pdf 19 2015/01/23 9:57:41
Important:
R When 3 Bluetooth devices (2 cellular
phones and 1 headset) are paired to the base unit, only 2 Bluetooth devices can be used with the unit at the same time, and the base unit loses its connection from other Bluetooth devices. To automatically resume the connection to Bluetooth devices, leave the auto connection on.
R Some cellular phones lose connection after
usage, please check the specifications of your cellular phone for more details.
1 MMENUN#632 2 M
bN: Select the desired setting.
3 MSAVEN a MOFFN
Note:
R Some cellular phones may ask you if you
accept the connection requirement from the base unit. In that case, select Off” in step
2. Check the specifications of your cellular phone.
Connecting/disconnecting the cellular phone manually
If you will not be using the paired cellular phone’s link to cell feature temporarily (for example, you do not want the unit to ring when your cellular line receives a call), you can disconnect your cellular phone from the base unit. If you want to use it again, reconnect the cellular phone to the base unit.
Note:
R Even if a paired cellular phone was
disconnected from the base unit, if it is brought within the base unit’s range during the auto connection interval, it may automatically connect to the base unit (page 19).
R A disconnected cellular phone is not
unpaired from the base unit, so pairing it to the base unit again is unnecessary.
1 To connect/disconnect:
For CELL 1: MMENUN#6251 For CELL 2: MMENUN#6252 R A long beep sounds.
2 MOFFN
Cellular line only mode (If you do not use the landline)
If you do not use the landline, we recommend setting the unit to the cellular line only mode.
Important:
R If you turn on the “Cell line only
mode, disconnect the telephone line cord from the base unit. Otherwise the “Cell line only mode cannot be activated.
1 MMENUN#157 2 To turn on:
M
bN: On a MSELECTN a
M
bN: Yes a MSELECTN
To turn off:
M
bN: Off a MSELECTN
Note:
R Once you set this mode, you can use the
following buttons to make cellular calls: – for the handset, press M
N or MZN
instead of MCELLN (page 22). – for the base unit, press M
ZN instead of
the line button (MCELL 1N or MCELL 2N)
set for the cellular line selection
(page 21, 28). (KX-TGE270 series:
page 3)
R Once you set this mode, the following
features cannot be used: – Landline features (page 44) – Answering system (page 56)
Messages cannot be received. – Voice mail features (page 63)
R After this mode is turned on or off, the base
unit reboots. – Bluetooth connections from cellular
phones or headset are disconnected. If
the auto connection is turned on
(page 19), the cellular phones are
reconnected. –
will be displayed on the handset momentarily. The handset can be used once
is displayed.
When you use the landline again
Before connecting the telephone line to the base unit, select Off” in step 2, “Cellular line
20
For assistance, please visit http://www.panasonic.com/help
Link to Cell
TGE26x_27x(en)_0123_ver110.pdf 20 2015/01/23 9:57:41
only mode (If you do not use the landline)”, page 20.
Cellular line selection
This feature determines which cellular line is selected to make cellular calls when: – you press MCELLN on the handset. – you press M
N or MZN on the handset
while the cellular line only mode is turned on.
– you press M
ZN on the base unit while the
cellular line only mode is turned on. (KX-TGE270 series: page 3)
The following settings are available: – Manual (handset only: default): You can
select the desired cellular line when making a call.
Cellphone 1*1 (base unit default):
CELL 1 is selected.
Cellphone 2*1: CELL 2 is selected.
1 For handset: MMENUN#634
For base unit*2: MMENUN#*634
2 M
bN: Select the desired setting.
3 MSAVEN a MOFFN
*1 After the Bluetooth device is paired, the
device name is displayed.
*2 KX-TGE270 series: page 3
Storing your area code (for dialing only a 7-digit phone number to make a local call)
You need to add your area code when making cellular calls to a phone number in your area. Once you store your area code, it is automatically added to the beginning of the 7-digit phone number when making cellular calls.
1 MMENUN#633 2 Enter the 3-digit area code.
R To correct a digit, press MCLEARN.
3 MSAVEN a MOFFN
Changing the Bluetooth PIN (Personal Identification Number)
The PIN is used to pair cellular phones to the base unit. The default PIN is 0000”. To prevent unauthorized access to this product, we recommend that you change the PIN, and keep it confidential.
Important:
R Please make note of your new PIN. The
unit does not reveal the PIN to you. If you forget your PIN, see page 75.
1 MMENUN#619
R If the unit prompts you to enter the old
PIN (when the default has been changed), enter the current 4-digit PIN.
2 Enter the new 4-digit PIN. a MOKN 3 Enter the new 4-digit PIN again. a
MSAVEN
4 MOFFN
For assistance, please visit http://www.panasonic.com/help
21
Link to Cell
TGE26x_27x(en)_0123_ver110.pdf 21 2015/01/23 9:57:41

Making cellular calls

Important:
R The unit can be used to talk on 2 lines at
the same time (for example, 2 cellular lines, or the landline and 1 cellular line).
R Only 2 Bluetooth devices can be used with
the unit at the same time (for example, 2 cellular lines, or the headset and 1 cellular line).
R Before making calls, confirm that the
corresponding CELL indicator on the base unit lights up (page 15).
1 Lift the handset and dial the phone
number.
R To correct a digit, press MCLEARN.
2 MCELLN
R The unit starts dialing when:
– only 1 cellular phone is paired. – a specific line is set to make cellular
calls (page 21).
Go to step 4.
3 M
bN: Select the desired cellular phone. a
MSELECTN
4 When you finish talking, press MOFFN or
place the handset on the base unit or charger.
Note:
R To switch to the speaker, press MZN.
To switch back to the receiver, press MZN/
M
N.
Adjusting the receiver or speaker volume
Press M
jN or MkN repeatedly while talking.
Making a cellular call using the redial list
The last 5 phone numbers dialed are stored in the redial list (each 48 digits max.).
1 M
EN REDIAL
2 M
bN: Select the desired phone number.
3 MCELLN
R The unit starts dialing when:
– only 1 cellular phone is paired.
– a specific line is set to make cellular
calls (page 21).
4 M
bN: Select the desired cellular phone. a
MSELECTN
Erasing a number in the redial list
n When a cellular phone is paired:
1 M
EN REDIAL
2 M
bN: Select the desired phone number.
a MMENUN
3 M
bN: “Erase” a MSELECTN
4 M
bN: “Yes” a MSELECTN
5 MOFFN
n When a cellular phone is not paired:
1 M
EN REDIAL
2 M
bN: Select the desired phone number.
a MERASEN
3 M
bN: “Yes” a MSELECTN
4 MOFFN

Making landline calls

1 Lift the handset and dial the phone
number.
R To correct a digit, press MCLEARN.
2 M
N
3 When you finish talking, press MOFFN or
place the handset on the base unit or charger.
Using the speakerphone
1 Dial the phone number and press M
ZN.
2 When you finish talking, press MOFFN.
Note:
R To switch back to the receiver, press M
ZN/
M
N.
Making a call using the redial list
The last 5 phone numbers dialed are stored in the redial list (each 48 digits max.).
1 M
EN REDIAL
22
For assistance, please visit http://www.panasonic.com/help

Making/Answering Calls Using the Handset

TGE26x_27x(en)_0123_ver110.pdf 22 2015/01/23 9:57:41
2 MbN: Select the desired phone number. 3 M
N
Pause (for PBX/long distance service users)
A pause is sometimes required when making calls using a PBX or long distance service. When storing a calling card access number and/or PIN in the phonebook, a pause is also needed (page 35). Example: If you need to dial the line access number “9” when making outside calls with a PBX:
1 9 a M
DN (Pause)
2 Dial the phone number. a M
N
Note:
R A 3.5 second pause is inserted each time
M
DN (Pause) is pressed.

Answering calls

When a call is being received, the ringer indicator and
indicator flash rapidly.
1 Lift the handset and press M
N or MZN
when the unit rings. R To answer a cellular call, you can also
press MCELLN.
2 When you finish talking, press MOFFN or
place the handset on the base unit or charger.
Any key answer: You can answer the call by pressing any dial key. Auto talk: You can answer calls simply by lifting the handset (page 43). Temporary handset ringer off: You can turn the ringer off temporarily by pressing M
N.
Using the Smart function key
When the
indicator flashes rapidly, press
M
N.
R You can answer the call even if the handset
is placed on the base unit or charger (page 16).
You can finish talking by pressing MOFFN without lifting up the handset.
Adjusting the handset ringer volume
Press M
jN or MkN repeatedly to select the
desired volume while ringing.

Useful features during a call

Hold
1 Press MMENUN during an outside call. 2 M
bN: “Hold” a MSELECTN
3 To release hold on the cellular line:
Press MCELLN.
*1
R Another handset user can take the call
by pressing MCELLN.
*1
*1 If you press MCELLN and the
selection list is displayed, select the desired cellular line and press
MSELECTN.
R The base unit user can take the call by
pressing MCELL 1N or MCELL 2N. (KX-TGE270 series: page 3)
To release hold on the landline:
Press M
N.
R Another handset user can take the call
by pressing M
N.
R The base unit user can take the call by
pressing M
ZN. (KX-TGE270 series:
page 3)
Note:
R After holding for 10 minutes, the call is
disconnected.
Mute
1 Press MMUTEN during a call. 2 To return to the call, press MMUTEN.
Note:
R MMUTEN is a soft key visible on the display
during a call.
For assistance, please visit http://www.panasonic.com/help
23
Making/Answering Calls Using the Handset
TGE26x_27x(en)_0123_ver110.pdf 23 2015/01/23 9:57:41
Flash for landline calls
MFLASHN allows you to use the special features of your host PBX such as transferring an extension call, or accessing optional telephone services.
Note:
R To change the flash time, see page 43.
For call waiting or Call Waiting C
aller ID service users
To use call waiting or Call Waiting Caller ID, you must first subscribe with your service provider/telephone company. This feature allows you to receive calls while you are already talking on the phone. If you receive a call while on the phone, you will hear a call waiting tone.
If you subscribe to both Caller ID and Call Waiting with Caller ID services, the 2nd
caller’s information is displayed after you hear the call waiting tone on the handset.
1 Press MCALL WAITN to answer the 2nd
call.
2 To switch between calls, press MCALL
WAITN.
Note:
R Please contact your service provider/
telephone company for details and availability of this service in your area.
Temporary tone dialing for landline calls (for rotary/pulse service users)
Press * (TONE) before entering access numbers which require tone dialing.
Handset clarity booster
This feature can improve sound clarity when the handset is used in an area where there may be interference. During an outside call, this feature is turned on automatically when necessary.
R When this feature is turned on,
is
displayed. However, during a cellular call,
is not displayed even though the
feature is activated.
Handset noise reduction
This feature allows you to hear the voice of the person you are talking to clearly, by reducing the surrounding noise coming from the other party’s telephone.
Press M
N to turn on/off while talking.
Note:
R Depending on the environment where this
handset is being used, this feature may not be effective.
R This feature is not available using the
speakerphone.
Handset equalizer
This feature clarifies the voice of the person you are talking to, producing a more natural-sounding voice that is easier to hear and understand.
1 Press MMENUN while talking. 2 MbN: “Equalizer” a MSELECTN 3 M
bN: Select the desired setting.
4 Press MOKN to exit.
Note:
R Depending on the condition and quality of
your telephone line, this feature may emphasize existing line noise. If it becomes difficult to hear, turn this feature off.
R This feature is not available while using the
speakerphone.
R When both the Equalizer” setting and
noise reduction are activated,
is
shown on the display.
Call share
You can join an existing outside call.
n While another unit is on a cellular call:
1 To join the conversation, press
MCELLN. R You can join the conversation when:
– only 1 cellular phone is paired.
24
For assistance, please visit http://www.panasonic.com/help
Making/Answering Calls Using the Handset
TGE26x_27x(en)_0123_ver110.pdf 24 2015/01/23 9:57:42
– a specific line is set to make
cellular calls (page 21).
2 M
bN: Select the desired cellular phone.
a MSELECTN
n While another unit is on a landline call:
To join the conversation, press M
N.
Note:
R A maximum of 3 parties (including 1 outside
party) can join a conversation using 2 extensions. (3-way conference)
R To prevent other users from joining your
conversations with outside callers, turn call sharing mode off (page 43).
Transferring calls, conference calls
Outside calls can be transferred or a conference call with an outside party can be made between 2 handsets.
1 During an outside call, press MMENUN. 2 M
bN: “Intercom” a MSELECTN
3 M
bN: Select the desired unit. a MSELECTN
4 Wait for the paged party to answer.
R If the paged party does not answer,
press M
N to return to the outside
call.
5 To complete the transfer:
Press MOFFN. To establish a conference call:
MMENUN a M
bN: Conference” a MSELECTN R To leave the conference, press MOFFN.
The other 2 parties can continue the conversation.
R To put the outside call on hold:
MMENUN a M
bN: Hold” a MSELECTN To resume the conference: MMENUN a M
bN: Conference” a MSELECTN
R To cancel the conference: MMENUN a
M
bN: Stop conference a
MSELECTN
You can continue the conversation with the outside caller.
Transferring a cellular call between the handset and a cellular phone
Transferring a cellular call from the handset to a cellular phone
1 Press MMENUN during a cellular call. 2 M
bN: Transfer to cell a MSELECTN R The cellular call is transferred to the
cellular phone.
Note:
R Depending on your cellular phone type, you
may need to set the cellular phone to be ready to talk before transferring. For example, if your cellular phone has a top cover, open it beforehand.
Transferring a cellular call from a cellular phone to the handset
During a conversation using a cellular phone, the call cannot be transferred to the handset by the cellular phone. Perform the following with the handset.
1 During a conversation using a cellular
phone, press MCELLN. R The call is transferred to the handset
when: – only 1 cellular phone is paired. – a specific line is set to make cellular
calls (page 21).
2 M
bN: Select the desired cellular phone. a MSELECTN R The call is transferred to the handset.
Answering a 2nd call
If you receive a call while talking on the phone, the interrupt tone sounds (page 41) and the 2nd caller’s information is displayed if you subscribe to Caller ID (page 49).
Answering a 2nd call during a landline call
1 Press MMENUN during a landline call.
For assistance, please visit http://www.panasonic.com/help
25
Making/Answering Calls Using the Handset
TGE26x_27x(en)_0123_ver110.pdf 25 2015/01/23 9:57:42
2 MbN: “Hold” a MSELECTN 3 To answer the 2nd call:
Press MCELLN while the 2nd call is being received.
4 To hang up the 2nd call and return to the
1st call (landline call), press MOFFN, then press M
N.
Answering a 2nd call during a cellular call
1 Press MMENUN during a cellular call. 2 M
bN: “Hold” a MSELECTN
3 To answer the 2nd call:
Press M
N or MCELLN while the 2nd call
is being received.
4 To hang up the 2nd call and return to the
1st call (cellular call), press MOFFN, then press MCELLN*1.
*1 If you press MCELLN and the selection list
is displayed, select the desired cellular line and press MSELECTN.

Power back-up operation for landline

When a power failure occurs, the charged handset temporarily supplies power to the base unit (power back-up mode). This allows you to make and receive landline calls using a handset during a power failure. The base unit will not perform any other functions. However, some functions such as Caller ID and phonebook are available only when using a handset other than the handset supplying power to the base unit. You can program
Power failure” and the default setting isAuto (page 43).
Important:
R If a handset is not placed on the base unit
when a power failure occurs, Base no power Press OFF” is displayed. After pressing MOFFN on the handset, place it on the base unit to start power back-up mode.
R Power back-up mode will not work if the
battery level of the power supplying handset is
or .
R Do not lift the power supplying handset
from the base unit during power back-up mode.
Panasonic Ni-MH battery performance (supplied batteries) during power back-up mode
When the batteries are fully charged, operating time of the handset in power back-up mode varies depending on usage. – Continuous use of the handset in power
back-up mode: 1.5 hours max.
– Continuous use of the handset other than a
handset in power back-up mode: 2 hours max.
– Not in use in power back-up mode: 2 hours
max.
Making calls during a power failure
n When only 1 handset is registered:
1 Lift the handset and dial the phone
number.
2 Within 1 minute, place the handset on
the base unit. R Wait until speakerphone is turned
on automatically and the call is made.
3 When the other party answers the call,
keep the handset on the base unit and talk using the speakerphone.
4 When you finish talking, press MOFFN.
n When 2 or more handsets are registered:
You should leave one handset on the base unit for supplying the power, and use another handset for making calls.
Note:
R The range of the base unit is limited during
a power failure. Please use the handset close to the base unit.
26
For assistance, please visit http://www.panasonic.com/help
Making/Answering Calls Using the Handset
TGE26x_27x(en)_0123_ver110.pdf 26 2015/01/23 9:57:42
Making a call using the redial list
n When only 1 handset is registered:
1 Lift the handset. 2 M
EN REDIAL
3 M
bN: Select the desired phone number.
4 Within 1 minute, place the handset on
the base unit. R Wait until speakerphone is turned
on automatically and the call is made.
n When 2 or more handsets are registered:
You should leave one handset on the base unit for supplying the power, and use another handset for making calls.
Making a call using the phonebook
There must be at least 2 handsets registered to the base unit in order for the phonebook feature to be used during a power failure.
You should leave one handset on the base unit for supplying the power, and use another handset for making calls.
Answering calls during a power failure
n When only 1 handset is registered:
1 When the unit rings, keep the handset
on the base unit and press M
N or
M
ZN.
R Speakerphone is turned on.
2 When you finish talking, press MOFFN.
n When 2 or more handsets are registered:
When the unit rings, use a handset which is not supplying power to the base unit. R Do not use or lift the handset which is
placed on the base unit during power back-up mode.
Note:
R The range of the base unit is limited during
a power failure. Please use the handset close to the base unit.
For assistance, please visit http://www.panasonic.com/help
27
Making/Answering Calls Using the Handset
TGE26x_27x(en)_0123_ver110.pdf 27 2015/01/23 9:57:42

Making cellular calls

Available for:
K
X-TGE270 series (page 3)
1 Press MCELL 1N or MCELL 2N. 2 Dial the phone number. 3 When the other party answers, speak into
the microphone.
4 When you finish talking, press M
ZN.
Note:
R For best performance, use the
speakerphone in a quiet environment.
R While on a call, you can switch from the
base unit to the handset: – With the call sharing mode on
(page 43), press MCELLN*1 on the handset. a M
bN: Select the desired cellular phone. a MSELECTN a Press MZN on the base unit.
– If the handset is on the base unit, simply
lift it.
*1 The call is taken when:
– only 1 cellular phone is paired. – a specific line is set to make cellular
calls (page 21).
Adjusting the speaker volume
Press M
jN or MkN repeatedly while talking.
Redialing the last number dialed
1 Press MCELL 1N or MCELL 2N. 2 MREDIALN

Making landline calls

1 MZN 2 Dial the phone number. 3 When the other party answers, speak into
the microphone.
4 When you finish talking, press M
ZN.
Note:
R While on a call, you can switch from the
base unit to the handset: – Press M
N on the handset, then press
M
ZN on the base unit with the call
sharing mode on (page 43).
– If the handset is on the base unit, simply
lift it.
Redialing the last number dialed
M
ZN a MREDIALN
Pause (for PBX/long distance service users)
A pause is sometimes required when making calls using a PBX or long distance service. When storing a calling card access number and/or PIN in the phonebook, a pause is also needed (page 35).
Example: If you need to dial the line access number “9” when making outside calls with a PBX:
1 M
ZN
2 9 a MPAUSEN 3 Dial the phone number.
Note:
R A 3.5 second pause is inserted each time
MPAUSEN is pressed.

Answering calls

When a landline call is being received, the SP-PHONE indicator flashes rapidly. When a cellular call is being received, the CELL indicator and SP-PHONE indicator flash rapidly.
1 Press M
ZN when the unit rings.
R You can also answer the cellular call
by pressing MCELL 1N or MCELL 2N.
2 Speak into the microphone. 3 When you finish talking, press MZN.
28
For assistance, please visit http://www.panasonic.com/help

Making/Answering Calls Using the Base Unit

TGE26x_27x(en)_0123_ver110.pdf 28 2015/01/23 9:57:42
Adjusting the base unit ringer volume
Press M
jN or MkN repeatedly to select the
desired volume while ringing. R To turn the ringer off, press and hold MkN
until the unit beeps.

Useful features during a call

Hold
1 Press MHOLDN during an outside call. 2 To release hold on the cellular line:
Press MCELL 1N or MCELL 2N. R A handset user can take the call:
MCELLN*1 a MSELECTN
*1 The call is taken when:
– only 1 cellular phone is paired. – a specific line is set to make
cellular calls (page 21).
To release hold on the landline:
Press M
ZN.
R A handset user can take the call by
pressing M
N.
Note:
R While a landline call is on hold, the
SP-PHONE indicator flashes.
R After holding for 10 minutes, the call is
disconnected.
Mute
1 Press MMUTEN during a call.
R The SP-PHONE indicator flashes.
2 To return to the call, press MMUTEN.
Flash for landline calls
MFLASHN allows you to use the special features of your host PBX such as transferring an extension call, or accessing optional telephone services.
Note:
R To change the flash time, see page 43.
For call waiting service users
To use call waiting, you must first subscribe with your service provider/telephone company. This feature allows you to receive calls while you are already talking on the phone. If you receive a call while on the phone, you will hear a call waiting tone.
1 Press MCALL WAITN to answer the 2nd
call.
2 To switch between calls, press MCALL
WAITN.
Note:
R Please contact your service provider/
telephone company for details and availability of this service in your area.
Temporary tone dialing for landline calls (for rotary/pulse service users)
Press * (TONE) before entering access numbers which require tone dialing.
Call share
You can join an existing outside call. To select the line that is being used for the call: – for a cellular line press MCELL 1N or MCELL
2N.
– for the landline press MZN.
Note:
R A maximum of 3 parties (including 1 outside
party) can join a conversation using 2 extensions. (3-way conference)
R To prevent other users from joining your
conversations with outside callers, turn call sharing mode off (page 43).
Transferring calls, conference calls
Outside calls can be transferred or a conference call with an outside party can be made between a handset and the base unit.
For assistance, please visit http://www.panasonic.com/help
29
Making/Answering Calls Using the Base Unit
TGE26x_27x(en)_0123_ver110.pdf 29 2015/01/23 9:57:42
Loading...
+ 67 hidden pages