Panasonic KX-TGA290, KX-TGA290B User Manual

2.4 GHz Expandable Cordless Handset

)

Model No.

KX-TGA290

Installation Manual

PLEASE READ BEFORE USE AND SAVE.

This handset is an accessory cordless handset, for use with Panasonic base unit
KX-TG2970. This installation manual only describes the steps necessary to start up the
handset. Please read the base unit operating instructions for further details.

Accessories (included) For extra orders, call 1-800-332-5368.

A Charger Unit . . . . . . . . . . . . . . . . . . . . . . . . .1

Charger Order No. PQLV30028ZB
AC Adaptor Order No. KX-TCA1-G (KX-TCA1)

A Handset Cover. . . . . . . . . . . . . . . . . . . . . . . .1

Order No. PQYNTG2970BR

Installation

Connecting the Charger unit

AC Adaptor

CHARGE

A Battery . . . . . . . . . . . . . . . . . . .1

Order No. HHR-P402

A Belt Clip . . . . . . . . . . . . . . . . . .1

Order No. PQKE10340Z2

Power Outlet
(AC 120 V, 60 Hz

• USE ONLY WITH Panasonic AC ADAPTOR KX-TCA1 (Order No. KX-TCA1-G).

• The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel

warm during use.)

• The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet.

Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the
adaptor may cause it to become disconnected.

Installing the battery

Insert the battery (1), and press it down until it snaps into the compartment (2).
Close the cover.

2

1

For assistance, please call: 1-800-ADT-ASAP

– 1 –

PQQX14266ZA S0804-1094

Charging the battery
Place the cordless handset on the charger and
charge for 6 hours before initial use.

• The unit beeps once, the CHARGE indicator lights

and “Charging” is displayed.

• When the battery is fully charged, “Charge

completed” is displayed if there are no new calls in

the Caller List.

• Recharge the battery when:

—“Recharge battery” is displayed on the

cordless handset,

3” flashes, or

—“
— the cordless handset beeps intermittently while it

is in use.

• If the battery has been discharged, the cordless handset will display “Charge for 6

HRS” and “

handset will not work unless the battery is charged. Continue charging.

4” when you place the cordless handset on the charger. The cordless

Charge
Contacts

CHARGE
Indicator

Handset battery information

After your Panasonic battery is fully charged, you can expect the following performance:

Operation Operating time

While in use (TALK) Up to 6 hours While not in use (Standby) Up to 14 days While using the Clarity Booster feature Up to 4 hours

• Clean the charge contacts of the cordless handset and the charger with a soft, dry
cloth once a month. Clean more often if the unit is subject to grease, dust or high
humidity. Otherwise the battery may not charge properly.

Belt Clip

You can hang the cordless handset on your belt or pocket using the included belt clip.

To attach the belt clip To remove the belt clip

While pressing the top of the clip (1),
pull the right edge in the direction of the
arrow (

– 2 –

2).

1

2

Registration

O KO K

This cordless handset must be registered to the KX-TG2970 base unit. The cordless
handset will be assigned the extension number at registration. Only one cordless handset
can be registered at a time. Charge the battery fully. Make sure the base unit and the

other cordless handsets are not being used.
base unit nearby during registration.

Have both the

[-]
Press MUTE on
base unit, then
OK on handset to
register handset

cordless

handset and

To operate “ ”,

[MUTE] and Indicator

The cordless handset display shows the instructions as shown
on the right.

press the right soft key.

OK

Press MUTE on
base unit, then
OK on handset to
register handset

BACK

PLAY OK

1 Base unit: Press [MUTE].

• The MUTE indicator flashes. After the MUTE indicator starts flashing, the rest of the

procedure must be completed within 1 minute.

2 Cordless Handset:

(1) Press the soft key ( ).

OK

IN USE

SPI

PRIVACY

Handset
Registering

(2) Wait until 3 beeps sound and the display shows

the new extension number.

• Registration is complete.

Ex. Extension number 2

IN USE

SPI

PRIVACY

Handset [2]
Registered

1

1

-

]

2

]

• The registered number “[1]” to “[3]” is shown on the top right of the display.

• You can stop registration by pressing [OFF] on the cordless handset and pressing
[MUTE] on the base unit.

To cancel the handset registration, please see your base unit Operating Instructions.

For assistance, please call: 1-800-ADT-ASAP

– 3 –

Optional Headset

k

Connecting an optional headset to the cordless handset allows hands-free phone
conversation. Please use only a Panasonic KX-TCA60, KX-TCA86, KX-TCA88,
KX-TCA88HA, KX-TCA91, KX-TCA92 or KX-TCA98 headset. To order, call the
accessories telephone number on page 1.

Connecting an optional headset

Open the headset jack cover, and insert the headset plug into the headset jack as shown
below.

Headset Jack

Headset Jac

• Headset sold separately. Model shown here is KX-TCA88.

Wall Mounting

The charger can be wall mounted. Connect the AC adaptor. Install screws using the wall
template (see below). Mount the charger (A). Slide it down (B), then slide down to the
right (C) until it is secured.

2.45 cm

31

⁄32")

(

2.45 cm
(31⁄32")

Screws
(not included)

To Power
Outlet

Wall Template

A

B

C

– 4 –

FCC and Other Information

WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST CALLS TO
EMERGENCY NUMBERS:

1. Remain on the line and briefly explain to the dispatcher the reason for the call.

Perform such activities in the off-peak hours, such as early morning or late evenings.

2.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

Privacy of communications may not be ensured when using this phone.

CAUTION:

Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this device.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

— Consult the dealer or an experienced radio/TV technician for help.
Operating near 2.4 GHz electrical appliances may cause interference. Move away from the

electrical appliances.

FCC RF Exposure Warning:

To comply with FCC RF exposure requirements, the handset unit may be carried and
operated with only the specific provided belt-clip. Other non-tested belt-clips or similar
body-worn accessories may not comply and must be avoided.

This equipment is hearing aid compatible as defined by the FCC in 47 CFR Section 68.316.

When you hold the phone to your ear, noise might be heard in your Hearing Aid. Some
Hearing Aids are not adequately shielded from external RF (radio frequency) energy. If
noise occurs, use an optional headset accessory or the speakerphone option (if
applicable) when using this phone. Consult your audiologist or Hearing Aid manufacturer
about the availability of Hearing Aids which provide adequate shielding to RF energy
commonly emitted by digital devices.

For assistance, please call: 1-800-ADT-ASAP

– 5 –

CAUTION:

To reduce the risk of fire or injury to persons, read and follow these instructions.

1. Use only the battery(ies) specified.

2. Do not dispose of the battery(ies) in a fire. They may explode. Check with local waste
management codes for special disposal instructions.

3. Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may
cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.

4. Exercise care in handling batteries in order not to short the battery to conductive
materials such as rings, bracelets, and keys. The battery and/or conductor may
overheat and cause burns.

5. Charge the battery(ies) provided with or identified for use with this product only in
accordance with the instructions and limitations specified in this manual.

A nickel metal hydride battery that is recyclable powers the product you
have purchased. Please call 1-800-8-BATTERY for information on how to
recycle this battery

.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR ANY TYPE OF MOISTURE.

• The AC adaptor is used as the main disconnect device, ensure that the AC outlet is

located/installed near the unit and is easily accessible.

Copyright:

This material is copyrighted by Panasonic Communications Co., Ltd., and may be
reproduced for internal use only. All other reproduction, in whole or in part, is prohibited
without the written consent of Panasonic Communications Co., Ltd.

© 2004 Panasonic Communications Co., Ltd. All Rights Reserved.

For your future reference

Serial No. Date of purchase

(found on the bottom of the unit)
Name and address of dealer.

If you need assistance with the setup or operation,
please call 1-800-ADT-ASAP

Panasonic World Wide Web address: http://www.panasonic.com

for customers in the USA or Puerto Rico
For customer inquiries:

• Read this Installation Manual or your base unit Operating Instructions.

• Please call 1-800-ADT-ASAP

Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America

One Panasonic Way, Secaucus, New Jersey 07094

Panasonic Sales Company,
Division of Matsushita Electric of Puerto Rico, Inc.

Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park
Carolina, Puerto Rico 00985

– 6 –

Unidad portátil inalámbrica expandible de 2.4 GHz

GE

T

Modelo

KX-TGA290

Manual de instalación

LÉALO ANTES DE LA UTILIZACIÓN Y LUEGO GUÁRDELO.

Esta unidad portátil es una unidad inalámbrica accesoria utilizable con la unidad base
KX-TG2970. Este manual de instalación sólo describe los pasos necesarios para poner en
funcionamiento la unidad portátil. Lea las instrucciones de funcionamiento de la unidad
base para más detalles.

Accesorios (incluidos) Para más pedidos, llame al 1-800-332-5368.

A Unidad de carga . . . . . . . . . . . . . . . . . . . . . .1

Nº. de pedido de la unidad de carga:
PQLV30028ZB
Nº. de pedido del adaptador de CA:
KX-TCA1-G (KX-TCA1)

A Cubierta de la unidad portátil. . . . . . . . . . . . .1

Nº. de pedido: PQYNTG2970BR

Instalación

Conecte la unidad de carga

A Batería . . . . . . . . . . . . . . . . . . .1

Nº. de pedido: HHR-P402

A Presilla para el cinturón . . . . . .1

Nº. de pedido: PQKE10340Z2

oma de corriente

Adaptador
de CA

(CA 120 V, 60 Hz)

CHARGE

• USAR SÓLO CON EL ADAPTADOR DE CA KX-TCA1 (Nº. de pedido: KX-TCA1-G) de

Panasonic.

• El adaptador de CA debe permanecer conectado en todo momento. (Es normal que el

adaptador se caliente durante su uso.)

Instalación de la batería

Inserte la batería (1), y empújela hacia abajo hasta que encaje con un chasquido
en el compartimento (2).

Cierre la cubierta

2

1

– (1) –

.

Carga de la batería

Coloque la unidad portátil en la unidad de carga y
cárguela durante 6 horas antes de empezar a usarla.

• La unidad emite un pitido, el indicador CHARGE se

ilumina, y “Charging” aparece en pantalla.

• Cuando la batería está completamente cargada,

aparece “Charge completed” si no hay llamadas
nuevas en la lista de personas que llaman.

• Recargue la batería cuando:

—“Recharge battery” aparece en la unidad

portátil,

3” parpadee, o

—“
— la unidad portátil emita pitidos intermitentes

mientras está en uso.

• Si la batería se ha descargado, la unidad portátil mostrará en pantalla “Charge for 6

HRS” y “4” cuando coloque la unidad portátil sobre la unidad de carga. La unidad

portátil no funcionará a no ser que la batería esté cargada. Siga cargando.

Contactos
de carga

Indicador
CHARGE

Información sobre la batería de la unidad portátil

Una vez que la batería de Panasonic está completamente cargada, puede esperar el
siguiente rendimiento:

Operación Tiempo de operación

En uso (HABLAR) Hasta 6 horas En espera (Espera) Hasta 14 días Mientras está en uso la función de refuerzo de la recepción Hasta 4 horas

• Limpie los contactos de carga de la unidad portátil y de la unidad de carga con un
paño suave y seco una vez al mes. Límpielos más a menudo si la unidad está
sometida a grasa, polvo o a humedad de nivel alta. De lo contrario, puede que la

batería no se cargue correctamente.

Presilla para el cinturón

La unidad portátil se puede colgar en el cinturón o en el bolsillo por medio de la presilla
para el cinturón suministrada.

Para poner la presilla para el cinturón Para quitar la presilla para el cinturón

A la vez que presiona la parte superior
de la presilla (
en dirección de la flecha (

– (2) –

1), tire del borde derecho

2).

1

2

Registro

O KO K

Esta unidad portátil inalámbrica debe registrarse en una unidad base KX-TG2970. A la
unidad portátil se le asignará su número de extensión al registrarla. Sólo se puede registrar
una unidad portátil cada vez. Cargue la batería completamente. Asegúrese de que la

unidad base y las demás unidades portátiles no se están utilizando.
tanto la unidad portátil como la unidad base durante el registro.

[-]
Press MUTE on
base unit, then
OK on handset to
register handset

Tenga a mano

Para accionar “ ”,

[MUTE] e indicador

La pantalla de la unidad portátil muestra las instrucciones tal y
como aparecen a la derecha.

1

Unidad base: Presione

• El indicador MUTE parpadea. Después de que el indicador MUTE empiece a

parpadear, el resto del procedimiento debe completarse antes de que pase 1 minuto.

[MUTE]

.

presione la tecla blanda
derecha.

2 Unidad portátil:

(1) Presione la tecla blanda ( ).

OK

OK

Press MUTE on
base unit, then
OK on handset to
register handset

BACK

IN USE

PLAY OK

SPI

PRIVACY

Handset
Registering

(2) Espere hasta que suene tres pitidos largos y que la

pantalla muestre el nuevo número de extensión.

• El registro ha finalizado.

Ej. Número de extensión 2

IN USE

SPI

PRIVACY

Handset [2]
Registered

1

1

-

]

2

]

• El número registrado “[1]” a “[3]” aparece en la esquina superior derecha de la pantalla.

• Puede detener el proceso de registro presionando [OFF] en la unidad portátil y

presionando [MUTE] en la unidad base.
Para cancelar el registro de la unidad portátil, consulte las instrucciones de

funcionamiento de la unidad base.

– (3) –

Auricular opcional

La conexión de un auricular opcional a la unidad portátil permite conversar telefónicamente
con las manos libres. Por favor, utilice solamente un auricular KX-TCA60, KX-TCA86,
KX-TCA88, KX-TCA88HA, KX-TCA91, KX-TCA92 o KX-TCA98 de Panasonic. Para hacer
un pedido, llame al número de teléfono de accesorios indicado en la página 1.

Conexión de un auricular opcional

Abra la cubierta de la toma del auricular, e inserte allí la clavija del auricular como se indica
abajo.

Toma del auricular

• El auricular se vende por separado. El modelo mostrado aquí es un KX-TCA88.

Montaje en pared

La unidad de carga se puede montar en la pared. Conecte el adaptador de CA. Introduzca
los tornillos usando la plantilla de pared (ver abajo). Monte la unidad de carga (
Deslícela hacia abajo (B), luego deslícela hacia abajo y a la derecha (C) hasta que
quede bien sujeta.

A).

2.45 cm

31

⁄32")

(

2.45 cm

31

⁄32")

(

Tornillos
(no incluído)

A la toma
de
corriente

Plantilla de pared

A

B

C

– (4) –

✄

For ADT Security System Customers, please call 1-800-ADT-ASAP

For ADT Security System Customers, please call 1-800-ADT-ASAP