Panasonic HQ-2102UH, HQ-2122UH User Manual

ROOM AIR CONDITIONER
INSTALLATION AND OPERATING INSTRUCTIONS
MODEL: HQ-2102UH
HQ-2122UH
Please read these operating instructions thoroughly before using your air conditioner and keep them for future reference.
For assistance, please call: 1-800-211-PANA (7262) or send e-mail to
consumerproducts@panasonic.com
© 2003 Matsushita Electrical Co., Ltd. All Right Reserved.
or refer to
www.panasonic.com
F564236
1
Please observe these following safety precautions when using your air conditioner.
Failure or negligence in observing these safety precautions could cause fire, electrical shock or personal injury.
INSTALLATION PRECAUTIONS
• Due to the weight of this product, we recommend that you have a helper to assist in the installation. To avoid injury, use the proper method of lifting. Avoid any sharp
SAFETY PRECAUTIONS
edges.
• Make sure the window frame to be used can properly support this product.
• This product must be installed in accordance with all local codes and ordinances.
• Do not install the unit in places where inflammable gas, fumes or soot may be generated.
OPERATION PRECAUTIONS
• Operate your air conditioner from a stable 115 volt AC supply.
• Plug into a separate 15 amp grounded outlet only.
• Use of extension cords Avoid using extension cords. If there are no alternatives,
ensure that the cord is a UL listed 3-wire grounding type, rated 125 volts with a minimum current-carrying rating of 15 amps, number 14 or heavier wire.
• Use a 15 amp time delay fuse or a circuit breaker.
• Do not switch off by unplugging the power plug while it is operating. Press the OFF/ON pad to “OFF” before unplugging.
This symbol (with a white background) denotes an action that is PROHIBITED.
These symbols (with a blue background) denote actions that are COMPULSORY.
OPERATION PRECAUTIONS
WARNING
• Do not modify the length of the power cord or use an extension cord.
• Do not touch or operate with wet hands. Do not modify or damage the cord.
• Do not turn on the unit by inserting the power plug. Do not switch off the unit by pulling out the power plug.
• Avoid an extended period of direct airflow.
• Do not insert sticks, fingers or other objects into the unit.
• Do not try to repair the unit yourself.
• Plug in properly before operating and use a specified power cord.
• If abnormal conditions (burnt smell, etc) occur, switch off and remove the power plug.
CAUTION
• Do not use the unit for other purposes, than its intended use.
• Do not remove the power plug by pulling the cord.
• Do not block the air intake and outlet vanes.
• Do not splash or direct water at the unit
• Do not expose the unit to direct sunlight during operation.
• Do not operate the unit without the air filter installed or when the front intake grille has been removed.
• Do not place any objects on the unit.
• Do not operate any combustion equipment near the unit’s airflow area.
• Switch off the breaker and remove the power plug from the socket if the unit will not be operated for a long period.
• Pay attention to any damages on the unit caused by extensive usage.
• Ventilate the room occasionally where the unit is installed.
• Remove the power plug when cleaning the unit.
This sign warns of risk of death or serious injury.
This sign warns of injury or damage to property.
POWER SUPPLY
Time Delay Fuse : 15 Amps Rated Voltage : 115V
• Socket Type
• Line Cord Plug
2
INSTALLATION BOX CONTENTS
Sealer 50 g (1.8 oz) (Putty)
Type A screws
Type C screws
Type A screw
Left side expandable panel
Top sealing ribbon
To p angle
Type B screws
ACCESSORIES
AIR CONDITIONER INSTALLATION
NOTE Check that none of the accessories are missing.
Window sash foam seal
Type A screws
(6 pcs) (XTN5D25A)
(5 pcs) (CWH4580211)
(6 pcs) (XTT4D8C)
Window sash sealing ribbon
SCREW FURNISHED
Side sealing ribbon
Type A screw
Type A Type B Type C (Qty 6) (Qty 5) (Qty 6)
SUGGESTED TOOL LIST
Type C screws
Right side expandable panel
SELECT THE BEST LOCATION
(Single or Double
Window
hung window)
Front grille
SIDE VIEW
Wood Machine Tapping Screw Screw Screw
Medium sized screwdriver (#2 Phillips)
Tape Measure
Pencil
Level
Knife or Scissor
19–3/
inches
16
12 inches
More than 4 inches
WINDOW REQUIREMENTS
• Hot sun rays hitting the outside surface of the cabinet will create considerable heat load. If the outside of the cabinet is exposed to direct sunlight, consider building an awning to shade the cabinet while providing ample area for the heated air to be exhausted from the condenser (both sides) and the top.
This unit is designed for installation in standard double hung windows.
NOTE The unit may also be installed “through the wall”. You should, however, observe standard carpentry practices and frame the opening without violating local ordinances.
INSTALLATION PROCEDURES
CHASSIS INSTALLATION INTO THE CABINET
1 Slide the chassis into the cabinet.
2 Reinstall the cabinet screws.
Secure the cabinet to chassis by using screws (from rear cabinet).
1 Remove the rear cabinet
screws and save for later use.
2 Slide the chassis out from the
cabinet.
HOW TO ASSEMBLE THE EXPANDABLE PANELS
Top angle
Expandable panel
Type B screws
NOTE This procedure applies to left and right
Type C screws
of assembling expandable panel.
• Attach the top angle to the cabinet using screw type B (3 pcs).
• Insert expandable panels to cabinet sides as shown.
• Secure the first fold of expansion panel to cabinet using screw type C (3 each).
CABINET INSTALLATION
1 Cut the “Sealing Ribbon” to the
proper length, and attach it along the bottom edge of the bottom window sash.
Window sash sealing ribbon
INSTALLATION OF THE FRONT GRILLE
Depending upon the location of the AC outlet, route the AC cord to either the left or right side while installing the front grille.
This figure shows the AC cord routed to the left side.
INSERT THE (OPTIONAL)
Attach the (part no. CZ-SF6P) to the frame.
Slot in the and the frame (part no. CZ-SFW6P) to the front grille.
2 To prevent condensation water
from dripping inside, the cabinet should be installed level or very slightly tilted to the outside.
3 Secure the cabinet using screws.
• Expand the expandable panel fully into the grooves of the window frame, secure the expandable panel, left, right and top mounting frames to the bottom of the window sash using 6 screws type A and 2 screws type B.
• Secure the cabinet using wood screws type A.
• Cut the window sash foam seal to the proper size and seal the opening between the top of the inside window sash and the outside window sash.
Note :If a gap exists between the unit and window sash, you may
use “Sealer” supplied with the installation kit for a better seal.
The and the frame can be obtained separately from your nearest service center.
INSERT THE AIR FILTER
Attach the air filter to the intake grille
°F
TIM ER
O P E R
ATIO
N
T E M
P / T
I M E
R
hr
S E T
O
S E
F
T
F
/
/O N
C A N C E L
C O O
L F A
M
N
O D
E
A I R
S W
I N G
E C
H
O
I G
N
H
O M
Y
M E
D
F
A
N S
P E E
D L O W
W
ire
less
R e m
o t e
C o n
t r o l
PLACE FRONT INTAKE GRILLE OVER THE FRONT GRILLE
Slide the front intake grille slightly to the right to reattach the tabs and then push it down to close tight.
Loading...
+ 5 hidden pages