Panasonic DP-100L User guide

INSTRUCTION MANUAL

DP-100L Series INDEX LIST

IMJE-DPLINDEX No.0061-91V

IO-Link setting file (IODD) can be downloaded from our website ( http://panasonic.net/id/pidsx/global ).

1 PHYSICAL LAYER

Model No.	DP-101ZL3-M-P-□		DP-102ZL3-M-P-□
Baud rate	COM3(230.4kbps)
Minimum cycle time		1ms
Process data length		4byte
Vendor ID		834
Device ID	0x060000		0x060001

2 PROCESS DATA(PD)

				bit
	7	6	5	4	3	2	1	0
PD0	Upper byte of pressure data
PD1	Lower byte of pressure data
	Scale
PD2	DP-101ZL3-M-P-□ : -1			(0.1kPa)
	DP-102ZL3-M-P-□ : -3			(0.001MPa
			0 (1kPa)

			PD3					Assignment		Remarks
			bit
7	6	5	4	3	2	1	0	Control output	0	: OFF
								(DO)	1	: ON
								Fixed	0
								Fixed	0
								Fixed	0
								Fixed	0
								Information	0	: No notification
								notification	1	: Notified
									0	: Normal
								Error level	1	: Caution
									2	: Fault

SERVICE DATA(SD)

	Index	Sub index	Name	R/W	Back up target	Format	Data length	Default data		Description of settings
									0x82 :	Reset setting
									0xA0 : Zero-adjustment setting
	2	0	System-Command	W		UInteger	1byte		0xA1 :	Remote zero-adjustment setting
									0xA2 : Zero-adjust setting unset
									0xA3 : Auto-reference setting
									Local User InterFace Lock
	12	0	Device Access Locks	R/W		Record	2byte	0	0 : UnLock , 8 : Lock
									Main unit : Linked with key lock
	16	0	Vendor Name	R		String	64byte
	17	0	Vendor Text	R		String	64byte
	18	0	Product Name	R		String	64byte
	19	0	Product ID	R		String	64byte
	20	0	Product Text	R		String	64byte
	21	0	Serial Number	R		String	16byte
	22	0	Hardware Version	R		String	8byte
	23	0	Firmware Version	R		String	8byte
	24	0	Application Specific Tag	R/W	○	String	32byte
	37	0	Detailed Device Status	R		UInteger	12byte
	40	0	Process-Data Input	R		UInteger	4byte
								DP-101□:	Threshold value of EASY mode
		1	Threshold Value Setting 1	R/W	○	Integer	2byte	-500 (-50.0)	Low-side threshold value of window comparator
								DP-102□:	mode / hysteresis mode
									DP101□ : -1010 to 1010		0xFC0E to 0x03F2
	60							0500 (0.500)	DP102□ : -101 to 1010		0xFF9B to 0x03F2
								DP-101□:	High-side threshold value of window comparator
		2	Threshold Value Setting 2	R/W	○	Integer	2byte	-495 (-49.5)	mode / hysteresis mode
								DP-102□:	DP101□ : -1010 to 1010		0xFC0E to 0x03F2
								0505 (0.505)	DP102□ : -101 to 1010		0xFF9B to 0x03F2
		1	Output Operation Setting of C/Q	R/W	○	UInteger	1byte	DP-101□:1	0 : N.O.		1 : N.C.
			Output					DP-102□:0
	61		Sensing Output Setting of C/Q						0x01 :	EASY mode
		2		R/W	○	UInteger	1byte	0x01	0x02 :	Hysteresis mode
			Output
									0x03 : Window comparator mode
		3	Hysteresis Setting of C/Q Output	R/W	○	Integer	2byte	3	Hysteresis value 8-step setting : 1 to 8
		1	Output Operation Setting of DO	R	○	UInteger	1byte		Linkage with Index61_1
			Output
	63	2	Sensing Output Setting of DO	R	○	UInteger	1byte		Linkage with Index61_2
			Output
		3	Hysteresis Setting of DO Output	R	○	Integer	2byte		Linkage with Index61_3
									1 : 2.5ms		6 : 100ms
									2 : 5ms		7 : 250ms
	66	0	Response Time Setting of Output	R/W	○	UInteger	1byte	1	3 : 10ms		8 : 500ms
									4 : 25ms		9 : 1,000ms
									5 : 50ms		A : 5,000ms
									0 : Normal operation (ECO mode is OFF)
	80	0	ECO Setting	R/W	○	UInteger	1byte	0	1 : Dimming mode (Std : The display becomes
									dark)
									3 : Off mode (FULL : The display is turned OFF)

Index	Sub index	Name	R/W	Back up target	Format	Data length	Default data		Description of settings
								0	: Red when ON,Green when OFF
	1	Display Color Setting of Main-	R/W	○	UInteger	1byte	0	1 : Green when ON,Red when OFF
		display Selection						2 : Always red
								3	: Always green
								0	: Std (Displays threshold)
								1	: OFF (Displays nothing)
		Display Setting of Sub-display						2	: Unit (Presently selected pressure unit is
	2		R/W	○	UInteger	2byte	0		displayed)
82		Selection
								3	: No** (Desired No. can be shown)
								4	: Cust (Desired numbers, alphabets and signs
									can be shown)
								0	: 250ms
	3	Display Speed Set	R/W	○	UInteger	1byte	0	1 : 500ms
								2	: 1000ms
	4	Peak / Bottom Hold Set	R/W	○	UInteger	1byte	0	0	: OFF
								1	: ON
							DP-101□ : 2	1 : MPa (This cannot be selected in the case of
83	0	Pressure Unit Set	R/W	○	UInteger	1byte	DP-102□ : 1	DP-101□)
								2	: kPa
	1	No** Display Set	R/W	○	String	2byte	01	Two half-width numeric characters : 01 to 99
84								Four half-width alphanumeric characters
	2	Custom Display Set	R/W	○	String	4byte	AAAA	* Error is generated if any of the following characters
								is entered.
								T , j , k , m , p , s , x
85	0	Zero-adjust	R		UInteger	1byte		0	: Not executed
								1	: In execution
163	0	Operating Time	R		UInteger	4byte		Operating time per 1-hour unit [h]
164	0	Number of Data Save Operations	R		UInteger	4byte		Increments each time setting data is stored in
								the nonvolatile memory.
168	0	Notification Flag Setting	R/W	○	UInteger	1byte		0	: Notify
								1	: Do not notify
169	0	Notification Event Code	R		UInteger	2byte		Newest event code readout

EVENT FUNCTION

Error indication	Event code	Error level	State
	0x7710	Fault	Short circuit overcurrent
	0x8CB0	Normal	Pressure applied during zero-adjustment	Information notification
	0x8CB1	Normal	External input outside the rated pressure range
	0x1811	Fault	Pressure element abnormality
Display of measured value	0x8D00	Caution	Operating time exceeded
Display of measured value	0x8D01	Caution	Max. number of the nonvolatile memory save opera-tions exceeded

http://panasonic.net/id/pidsx/global

Overseas Sales Division (Head Office)

2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan Phone: [phone] FAX: [phone]

For sales network, please visit our website.

© Panasonic Industrial Devices SUNX Co., Ltd. 2018 PRINTED IN JAPAN